| Message ID | 20240426125707.585269-11-christophe.roullier@foss.st.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Series to deliver Ethernets for STM32MP13 | expand |
On 4/26/24 2:57 PM, Christophe Roullier wrote: > Add dual Ethernet: > -Ethernet1: RMII with crystal > -Ethernet2: RMII without crystal > PHYs used are SMSC (LAN8742A) > > With Ethernet1, we can performed WoL from PHY instead of GMAC point > of view. > (in this case IRQ for WoL is managed as wakeup pin and configured > in OS secure). How does the Linux PHY driver process such a PHY IRQ ? Or is Linux unaware of the PHY IRQ ? Doesn't that cause issues ? > diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts b/arch/arm/boot/dts/st/stm32mp135f-dk.dts > index 567e53ad285f..3b8eb0ab9ab9 100644 > --- a/arch/arm/boot/dts/st/stm32mp135f-dk.dts > +++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts > @@ -19,6 +19,8 @@ / { > compatible = "st,stm32mp135f-dk", "st,stm32mp135"; > > aliases { > + ethernet0 = ðernet1; > + ethernet1 = ðernet2; > serial0 = &uart4; > serial1 = &usart1; > serial2 = &uart8; > @@ -141,6 +143,52 @@ &cryp { > status = "okay"; > }; > > +ðernet1 { > + status = "okay"; > + pinctrl-0 = <ð1_rmii_pins_a>; > + pinctrl-1 = <ð1_rmii_sleep_pins_a>; > + pinctrl-names = "default", "sleep"; > + phy-mode = "rmii"; > + max-speed = <100>; > + phy-handle = <&phy0_eth1>; Keep the list sorted please (is the max-speed even needed? if not, drop it) > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "snps,dwmac-mdio"; > + > + phy0_eth1: ethernet-phy@0 { > + compatible = "ethernet-phy-id0007.c131"; > + reset-gpios = <&mcp23017 9 GPIO_ACTIVE_LOW>; > + reg = <0>; > + wakeup-source; > + }; > + }; > +}; > + > +ðernet2 { > + status = "okay"; > + pinctrl-0 = <ð2_rmii_pins_a>; > + pinctrl-1 = <ð2_rmii_sleep_pins_a>; > + pinctrl-names = "default", "sleep"; > + phy-mode = "rmii"; > + max-speed = <100>; > + phy-handle = <&phy0_eth2>; > + st,ext-phyclk; > + phy-supply = <&scmi_v3v3_sw>; Sort please [...]
Hi Marek On 4/26/24 17:44, Marek Vasut wrote: > On 4/26/24 2:57 PM, Christophe Roullier wrote: >> Add dual Ethernet: >> -Ethernet1: RMII with crystal >> -Ethernet2: RMII without crystal >> PHYs used are SMSC (LAN8742A) >> >> With Ethernet1, we can performed WoL from PHY instead of GMAC point >> of view. >> (in this case IRQ for WoL is managed as wakeup pin and configured >> in OS secure). > > How does the Linux PHY driver process such a PHY IRQ ? > > Or is Linux unaware of the PHY IRQ ? Doesn't that cause issues ? In this case, we want to have an example to wakeup the system from Standby low power mode (VDDCPU and VDD_CORE off) thanks to a magic packet detected by the PHY. The PHY then assert his interrupt output signal. On MP13 DK platform, this PHY signal is connected to a specific GPIO aka "Wakeup pins" (only 6 wakeup pins an MP13). Those specific GPIOs are handled by the PWR peripheral which is controlled by the secure OS. On WoL packet, the Secure OS catches the PHY interrupt and uses asynchronous notification mechanism to warn Linux (on our platform we use a PPI). On Linux side, Optee core driver creates an irq domain/irqchip triggered on the asynchronous notification. Each device which use a wakeup pin need then to request an IRQ on this "Optee irq domain". This OPTEE irq domain will be pushed soon. cheers Alex > >> diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts >> b/arch/arm/boot/dts/st/stm32mp135f-dk.dts >> index 567e53ad285f..3b8eb0ab9ab9 100644 >> --- a/arch/arm/boot/dts/st/stm32mp135f-dk.dts >> +++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts >> @@ -19,6 +19,8 @@ / { >> compatible = "st,stm32mp135f-dk", "st,stm32mp135"; >> aliases { >> + ethernet0 = ðernet1; >> + ethernet1 = ðernet2; >> serial0 = &uart4; >> serial1 = &usart1; >> serial2 = &uart8; >> @@ -141,6 +143,52 @@ &cryp { >> status = "okay"; >> }; >> +ðernet1 { >> + status = "okay"; >> + pinctrl-0 = <ð1_rmii_pins_a>; >> + pinctrl-1 = <ð1_rmii_sleep_pins_a>; >> + pinctrl-names = "default", "sleep"; >> + phy-mode = "rmii"; >> + max-speed = <100>; >> + phy-handle = <&phy0_eth1>; > > Keep the list sorted please (is the max-speed even needed? if not, drop it) > >> + mdio { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "snps,dwmac-mdio"; >> + >> + phy0_eth1: ethernet-phy@0 { >> + compatible = "ethernet-phy-id0007.c131"; >> + reset-gpios = <&mcp23017 9 GPIO_ACTIVE_LOW>; >> + reg = <0>; >> + wakeup-source; >> + }; >> + }; >> +}; >> + >> +ðernet2 { >> + status = "okay"; >> + pinctrl-0 = <ð2_rmii_pins_a>; >> + pinctrl-1 = <ð2_rmii_sleep_pins_a>; >> + pinctrl-names = "default", "sleep"; >> + phy-mode = "rmii"; >> + max-speed = <100>; >> + phy-handle = <&phy0_eth2>; >> + st,ext-phyclk; >> + phy-supply = <&scmi_v3v3_sw>; > > Sort please > > [...]
On 5/13/24 6:01 PM, Alexandre TORGUE wrote: > Hi Marek Hi, > On 4/26/24 17:44, Marek Vasut wrote: >> On 4/26/24 2:57 PM, Christophe Roullier wrote: >>> Add dual Ethernet: >>> -Ethernet1: RMII with crystal >>> -Ethernet2: RMII without crystal >>> PHYs used are SMSC (LAN8742A) >>> >>> With Ethernet1, we can performed WoL from PHY instead of GMAC point >>> of view. >>> (in this case IRQ for WoL is managed as wakeup pin and configured >>> in OS secure). >> >> How does the Linux PHY driver process such a PHY IRQ ? >> >> Or is Linux unaware of the PHY IRQ ? Doesn't that cause issues ? > > In this case, we want to have an example to wakeup the system from > Standby low power mode (VDDCPU and VDD_CORE off) thanks to a magic > packet detected by the PHY. The PHY then assert his interrupt output > signal. > On MP13 DK platform, this PHY signal is connected to a specific GPIO > aka "Wakeup pins" (only 6 wakeup pins an MP13). Those specific GPIOs are > handled by the PWR peripheral which is controlled by the secure OS. What does configure the PHY for this wakeup mode ? > On WoL packet, the Secure OS catches the PHY interrupt and uses > asynchronous notification mechanism to warn Linux (on our platform we > use a PPI). On Linux side, Optee core driver creates an irq > domain/irqchip triggered on the asynchronous notification. Each device > which use a wakeup pin need then to request an IRQ on this "Optee irq > domain". > > This OPTEE irq domain will be pushed soon. I suspect it might make sense to add this WoL part separately from the actual ethernet DT nodes, so ethernet could land and the WoL functionality can be added when it is ready ?
Hi On 5/16/24 02:23, Marek Vasut wrote: > On 5/13/24 6:01 PM, Alexandre TORGUE wrote: >> Hi Marek > > Hi, > >> On 4/26/24 17:44, Marek Vasut wrote: >>> On 4/26/24 2:57 PM, Christophe Roullier wrote: >>>> Add dual Ethernet: >>>> -Ethernet1: RMII with crystal >>>> -Ethernet2: RMII without crystal >>>> PHYs used are SMSC (LAN8742A) >>>> >>>> With Ethernet1, we can performed WoL from PHY instead of GMAC point >>>> of view. >>>> (in this case IRQ for WoL is managed as wakeup pin and configured >>>> in OS secure). >>> >>> How does the Linux PHY driver process such a PHY IRQ ? >>> >>> Or is Linux unaware of the PHY IRQ ? Doesn't that cause issues ? >> >> In this case, we want to have an example to wakeup the system from >> Standby low power mode (VDDCPU and VDD_CORE off) thanks to a magic >> packet detected by the PHY. The PHY then assert his interrupt output >> signal. >> On MP13 DK platform, this PHY signal is connected to a specific GPIO >> aka "Wakeup pins" (only 6 wakeup pins an MP13). Those specific GPIOs >> are handled by the PWR peripheral which is controlled by the secure OS. > > What does configure the PHY for this wakeup mode ? Linux device tree. > >> On WoL packet, the Secure OS catches the PHY interrupt and uses >> asynchronous notification mechanism to warn Linux (on our platform we >> use a PPI). On Linux side, Optee core driver creates an irq >> domain/irqchip triggered on the asynchronous notification. Each device >> which use a wakeup pin need then to request an IRQ on this "Optee irq >> domain". >> >> This OPTEE irq domain will be pushed soon. > > I suspect it might make sense to add this WoL part separately from the > actual ethernet DT nodes, so ethernet could land and the WoL > functionality can be added when it is ready ? If at the end we want to have this Wol from PHY then I agree we need to wait. We could push a WoL from MAC for this node before optee driver patches merge but not sure it makes sens. Alex
> > I suspect it might make sense to add this WoL part separately from the > > actual ethernet DT nodes, so ethernet could land and the WoL > > functionality can be added when it is ready ? > > If at the end we want to have this Wol from PHY then I agree we need to > wait. We could push a WoL from MAC for this node before optee driver patches > merge but not sure it makes sens. In general, it is better if the PHY does WoL, since the MAC can then be powered down. MAC WoL should only be used when the PHY does not support the requested WoL configuration, but the MAC can. And sometimes you need to spread it over both the PHY and the MAC. Andrew
On 5/16/24 14:22, Andrew Lunn wrote: >>> I suspect it might make sense to add this WoL part separately from the >>> actual ethernet DT nodes, so ethernet could land and the WoL >>> functionality can be added when it is ready ? >> >> If at the end we want to have this Wol from PHY then I agree we need to >> wait. We could push a WoL from MAC for this node before optee driver patches >> merge but not sure it makes sens. > > In general, it is better if the PHY does WoL, since the MAC can then > be powered down. MAC WoL should only be used when the PHY does not > support the requested WoL configuration, but the MAC can. And > sometimes you need to spread it over both the PHY and the MAC. > thanks Andrew. So lets wait the optee driver missing part. alex > Andrew
diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts b/arch/arm/boot/dts/st/stm32mp135f-dk.dts index 567e53ad285f..3b8eb0ab9ab9 100644 --- a/arch/arm/boot/dts/st/stm32mp135f-dk.dts +++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts @@ -19,6 +19,8 @@ / { compatible = "st,stm32mp135f-dk", "st,stm32mp135"; aliases { + ethernet0 = ðernet1; + ethernet1 = ðernet2; serial0 = &uart4; serial1 = &usart1; serial2 = &uart8; @@ -141,6 +143,52 @@ &cryp { status = "okay"; }; +ðernet1 { + status = "okay"; + pinctrl-0 = <ð1_rmii_pins_a>; + pinctrl-1 = <ð1_rmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rmii"; + max-speed = <100>; + phy-handle = <&phy0_eth1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0_eth1: ethernet-phy@0 { + compatible = "ethernet-phy-id0007.c131"; + reset-gpios = <&mcp23017 9 GPIO_ACTIVE_LOW>; + reg = <0>; + wakeup-source; + }; + }; +}; + +ðernet2 { + status = "okay"; + pinctrl-0 = <ð2_rmii_pins_a>; + pinctrl-1 = <ð2_rmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rmii"; + max-speed = <100>; + phy-handle = <&phy0_eth2>; + st,ext-phyclk; + phy-supply = <&scmi_v3v3_sw>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0_eth2: ethernet-phy@0 { + compatible = "ethernet-phy-id0007.c131"; + reset-gpios = <&mcp23017 10 GPIO_ACTIVE_LOW>; + reg = <0>; + }; + }; +}; + &i2c1 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c1_pins_a>;
Add dual Ethernet: -Ethernet1: RMII with crystal -Ethernet2: RMII without crystal PHYs used are SMSC (LAN8742A) With Ethernet1, we can performed WoL from PHY instead of GMAC point of view. (in this case IRQ for WoL is managed as wakeup pin and configured in OS secure). Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com> --- arch/arm/boot/dts/st/stm32mp135f-dk.dts | 48 +++++++++++++++++++++++++ 1 file changed, 48 insertions(+)