@@ -1007,3 +1007,1086 @@ void ixgbe_copy_phy_caps_to_cfg(struct ixgbe_aci_cmd_get_phy_caps_data *caps,
cfg->module_compliance_enforcement =
caps->module_compliance_enforcement;
}
+
+/**
+ * ixgbe_aci_set_phy_cfg - set PHY configuration
+ * @hw: pointer to the HW struct
+ * @cfg: structure with PHY configuration data to be set
+ *
+ * Set the various PHY configuration parameters supported on the Port
+ * using ACI command (0x0601).
+ * One or more of the Set PHY config parameters may be ignored in an MFP
+ * mode as the PF may not have the privilege to set some of the PHY Config
+ * parameters.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_set_phy_cfg(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_set_phy_cfg_data *cfg)
+{
+ struct ixgbe_aci_desc desc;
+ int err;
+
+ if (!cfg)
+ return -EINVAL;
+
+ /* Ensure that only valid bits of cfg->caps can be turned on. */
+ cfg->caps &= IXGBE_ACI_PHY_ENA_VALID_MASK;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_set_phy_cfg);
+ desc.params.set_phy.lport_num = hw->bus.func;
+ desc.flags |= IXGBE_ACI_FLAG_RD;
+
+ err = ixgbe_aci_send_cmd(hw, &desc, cfg, sizeof(*cfg));
+
+ if (!err)
+ hw->phy.curr_user_phy_cfg = *cfg;
+
+ return err;
+}
+
+/**
+ * ixgbe_aci_set_link_restart_an - set up link and restart AN
+ * @hw: pointer to the HW struct
+ * @ena_link: if true: enable link, if false: disable link
+ *
+ * Function sets up the link and restarts the Auto-Negotiation over the link.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_set_link_restart_an(struct ixgbe_hw *hw, bool ena_link)
+{
+ struct ixgbe_aci_cmd_restart_an *cmd;
+ struct ixgbe_aci_desc desc;
+
+ cmd = &desc.params.restart_an;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_restart_an);
+
+ cmd->cmd_flags = IXGBE_ACI_RESTART_AN_LINK_RESTART;
+ cmd->lport_num = hw->bus.func;
+ if (ena_link)
+ cmd->cmd_flags |= IXGBE_ACI_RESTART_AN_LINK_ENABLE;
+ else
+ cmd->cmd_flags &= ~IXGBE_ACI_RESTART_AN_LINK_ENABLE;
+
+ return ixgbe_aci_send_cmd(hw, &desc, NULL, 0);
+}
+
+/**
+ * ixgbe_is_media_cage_present - check if media cage is present
+ * @hw: pointer to the HW struct
+ *
+ * Identify presence of media cage using the ACI command (0x06E0).
+ *
+ * Return: true if media cage is present, else false. If no cage, then
+ * media type is backplane or BASE-T.
+ */
+static bool ixgbe_is_media_cage_present(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_link_topo *cmd;
+ struct ixgbe_aci_desc desc;
+
+ cmd = &desc.params.get_link_topo;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_get_link_topo);
+
+ cmd->addr.topo_params.node_type_ctx =
+ FIELD_PREP(IXGBE_ACI_LINK_TOPO_NODE_CTX_M,
+ IXGBE_ACI_LINK_TOPO_NODE_CTX_PORT);
+
+ /* Set node type. */
+ cmd->addr.topo_params.node_type_ctx |=
+ (IXGBE_ACI_LINK_TOPO_NODE_TYPE_M &
+ IXGBE_ACI_LINK_TOPO_NODE_TYPE_CAGE);
+
+ /* Node type cage can be used to determine if cage is present. If AQC
+ * returns error (ENOENT), then no cage present. If no cage present then
+ * connection type is backplane or BASE-T.
+ */
+ return ixgbe_aci_get_netlist_node(hw, cmd, NULL, NULL);
+}
+
+/**
+ * ixgbe_get_media_type_from_phy_type - Gets media type based on phy type
+ * @hw: pointer to the HW struct
+ *
+ * Try to identify the media type based on the phy type.
+ * If more than one media type, the ixgbe_media_type_unknown is returned.
+ * First, phy_type_low is checked, then phy_type_high.
+ * If none are identified, the ixgbe_media_type_unknown is returned
+ *
+ * Return: type of a media based on phy type in form of enum.
+ */
+static enum ixgbe_media_type
+ixgbe_get_media_type_from_phy_type(struct ixgbe_hw *hw)
+{
+ struct ixgbe_link_status *hw_link_info;
+
+ if (!hw)
+ return ixgbe_media_type_unknown;
+
+ hw_link_info = &hw->link.link_info;
+ if (hw_link_info->phy_type_low && hw_link_info->phy_type_high)
+ /* If more than one media type is selected, report unknown */
+ return ixgbe_media_type_unknown;
+
+ if (hw_link_info->phy_type_low) {
+ /* 1G SGMII is a special case where some DA cable PHYs
+ * may show this as an option when it really shouldn't
+ * be since SGMII is meant to be between a MAC and a PHY
+ * in a backplane. Try to detect this case and handle it
+ */
+ if (hw_link_info->phy_type_low == IXGBE_PHY_TYPE_LOW_1G_SGMII &&
+ (hw_link_info->module_type[IXGBE_ACI_MOD_TYPE_IDENT] ==
+ IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_ACTIVE ||
+ hw_link_info->module_type[IXGBE_ACI_MOD_TYPE_IDENT] ==
+ IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_PASSIVE))
+ return ixgbe_media_type_da;
+
+ switch (hw_link_info->phy_type_low) {
+ case IXGBE_PHY_TYPE_LOW_1000BASE_SX:
+ case IXGBE_PHY_TYPE_LOW_1000BASE_LX:
+ case IXGBE_PHY_TYPE_LOW_10GBASE_SR:
+ case IXGBE_PHY_TYPE_LOW_10GBASE_LR:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_SR:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_LR:
+ return ixgbe_media_type_fiber;
+ case IXGBE_PHY_TYPE_LOW_10G_SFI_AOC_ACC:
+ case IXGBE_PHY_TYPE_LOW_25G_AUI_AOC_ACC:
+ return ixgbe_media_type_fiber;
+ case IXGBE_PHY_TYPE_LOW_100BASE_TX:
+ case IXGBE_PHY_TYPE_LOW_1000BASE_T:
+ case IXGBE_PHY_TYPE_LOW_2500BASE_T:
+ case IXGBE_PHY_TYPE_LOW_5GBASE_T:
+ case IXGBE_PHY_TYPE_LOW_10GBASE_T:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_T:
+ return ixgbe_media_type_copper;
+ case IXGBE_PHY_TYPE_LOW_10G_SFI_DA:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_CR:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_CR_S:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_CR1:
+ return ixgbe_media_type_da;
+ case IXGBE_PHY_TYPE_LOW_25G_AUI_C2C:
+ if (ixgbe_is_media_cage_present(hw))
+ return ixgbe_media_type_aui;
+ fallthrough;
+ case IXGBE_PHY_TYPE_LOW_1000BASE_KX:
+ case IXGBE_PHY_TYPE_LOW_2500BASE_KX:
+ case IXGBE_PHY_TYPE_LOW_2500BASE_X:
+ case IXGBE_PHY_TYPE_LOW_5GBASE_KR:
+ case IXGBE_PHY_TYPE_LOW_10GBASE_KR_CR1:
+ case IXGBE_PHY_TYPE_LOW_10G_SFI_C2C:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_KR:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_KR1:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_KR_S:
+ return ixgbe_media_type_backplane;
+ }
+ } else {
+ switch (hw_link_info->phy_type_high) {
+ case IXGBE_PHY_TYPE_HIGH_10BASE_T:
+ return ixgbe_media_type_copper;
+ }
+ }
+ return ixgbe_media_type_unknown;
+}
+
+/**
+ * ixgbe_update_link_info - update status of the HW network link
+ * @hw: pointer to the HW struct
+ *
+ * Update the status of the HW network link.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_update_link_info(struct ixgbe_hw *hw)
+{
+ struct ixgbe_link_status *li;
+ int err;
+
+ if (!hw)
+ return -EINVAL;
+
+ li = &hw->link.link_info;
+
+ err = ixgbe_aci_get_link_info(hw, true, NULL);
+ if (err)
+ return err;
+
+ if (li->link_info & IXGBE_ACI_MEDIA_AVAILABLE) {
+ struct ixgbe_aci_cmd_get_phy_caps_data __free(kfree) *pcaps;
+
+ pcaps = kzalloc(sizeof(*pcaps), GFP_KERNEL);
+ if (!pcaps)
+ return -ENOMEM;
+
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_TOPO_CAP_MEDIA,
+ pcaps);
+
+ if (!err)
+ memcpy(li->module_type, &pcaps->module_type,
+ sizeof(li->module_type));
+ }
+
+ return err;
+}
+
+/**
+ * ixgbe_get_link_status - get status of the HW network link
+ * @hw: pointer to the HW struct
+ * @link_up: pointer to bool (true/false = linkup/linkdown)
+ *
+ * Variable link_up is true if link is up, false if link is down.
+ * The variable link_up is invalid if status is non zero. As a
+ * result of this call, link status reporting becomes enabled
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_get_link_status(struct ixgbe_hw *hw, bool *link_up)
+{
+ int err = 0;
+
+ if (!hw || !link_up)
+ return -EINVAL;
+
+ if (hw->link.get_link_info) {
+ err = ixgbe_update_link_info(hw);
+ if (err)
+ return err;
+ }
+
+ *link_up = hw->link.link_info.link_info & IXGBE_ACI_LINK_UP;
+
+ return err;
+}
+
+/**
+ * ixgbe_aci_get_link_info - get the link status
+ * @hw: pointer to the HW struct
+ * @ena_lse: enable/disable LinkStatusEvent reporting
+ * @link: pointer to link status structure - optional
+ *
+ * Get the current Link Status using ACI command (0x607).
+ * The current link can be optionally provided to update
+ * the status.
+ *
+ * Return: the link status of the adapter.
+ */
+int ixgbe_aci_get_link_info(struct ixgbe_hw *hw, bool ena_lse,
+ struct ixgbe_link_status *link)
+{
+ struct ixgbe_aci_cmd_get_link_status_data link_data = { 0 };
+ struct ixgbe_aci_cmd_get_link_status *resp;
+ struct ixgbe_link_status *li_old, *li;
+ struct ixgbe_fc_info *hw_fc_info;
+ enum ixgbe_media_type *hw_media_type;
+ struct ixgbe_aci_desc desc;
+ bool tx_pause, rx_pause;
+ u16 cmd_flags;
+ int err;
+
+ if (!hw)
+ return -EINVAL;
+
+ li_old = &hw->link.link_info_old;
+ hw_media_type = &hw->phy.media_type;
+ li = &hw->link.link_info;
+ hw_fc_info = &hw->fc;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_get_link_status);
+ cmd_flags = (ena_lse) ? IXGBE_ACI_LSE_ENA : IXGBE_ACI_LSE_DIS;
+ resp = &desc.params.get_link_status;
+ resp->cmd_flags = cmd_flags;
+ resp->lport_num = hw->bus.func;
+
+ err = ixgbe_aci_send_cmd(hw, &desc, &link_data, sizeof(link_data));
+
+ if (err)
+ return err;
+
+ /* Save off old link status information. */
+ *li_old = *li;
+
+ /* Update current link status information. */
+ li->link_speed = link_data.link_speed;
+ li->phy_type_low = link_data.phy_type_low;
+ li->phy_type_high = link_data.phy_type_high;
+ *hw_media_type = ixgbe_get_media_type_from_phy_type(hw);
+ li->link_info = link_data.link_info;
+ li->link_cfg_err = link_data.link_cfg_err;
+ li->an_info = link_data.an_info;
+ li->ext_info = link_data.ext_info;
+ li->max_frame_size = link_data.max_frame_size;
+ li->fec_info = link_data.cfg & IXGBE_ACI_FEC_MASK;
+ li->topo_media_conflict = link_data.topo_media_conflict;
+ li->pacing = link_data.cfg & (IXGBE_ACI_CFG_PACING_M |
+ IXGBE_ACI_CFG_PACING_TYPE_M);
+
+ /* Update fc info. */
+ tx_pause = !!(link_data.an_info & IXGBE_ACI_LINK_PAUSE_TX);
+ rx_pause = !!(link_data.an_info & IXGBE_ACI_LINK_PAUSE_RX);
+ if (tx_pause && rx_pause)
+ hw_fc_info->current_mode = ixgbe_fc_full;
+ else if (tx_pause)
+ hw_fc_info->current_mode = ixgbe_fc_tx_pause;
+ else if (rx_pause)
+ hw_fc_info->current_mode = ixgbe_fc_rx_pause;
+ else
+ hw_fc_info->current_mode = ixgbe_fc_none;
+
+ li->lse_ena = !!(resp->cmd_flags & IXGBE_ACI_LSE_IS_ENABLED);
+
+ /* Save link status information. */
+ if (link)
+ *link = *li;
+
+ /* Flag cleared so calling functions don't call AQ again. */
+ hw->link.get_link_info = false;
+
+ return 0;
+}
+
+/**
+ * ixgbe_aci_set_event_mask - set event mask
+ * @hw: pointer to the HW struct
+ * @port_num: port number of the physical function
+ * @mask: event mask to be set
+ *
+ * Set the event mask using ACI command (0x0613).
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_set_event_mask(struct ixgbe_hw *hw, u8 port_num, u16 mask)
+{
+ struct ixgbe_aci_cmd_set_event_mask *cmd;
+ struct ixgbe_aci_desc desc;
+
+ cmd = &desc.params.set_event_mask;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_set_event_mask);
+
+ cmd->lport_num = port_num;
+
+ cmd->event_mask = mask;
+ return ixgbe_aci_send_cmd(hw, &desc, NULL, 0);
+}
+
+/**
+ * ixgbe_configure_lse - enable/disable link status events
+ * @hw: pointer to the HW struct
+ * @activate: true for enable lse, false otherwise
+ * @mask: event mask to be set; a set bit means deactivation of the
+ * corresponding event
+ *
+ * Set the event mask and then enable or disable link status events
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_configure_lse(struct ixgbe_hw *hw, bool activate, u16 mask)
+{
+ int err;
+
+ err = ixgbe_aci_set_event_mask(hw, hw->bus.func, mask);
+ if (err)
+ return err;
+
+ /* Enabling link status events generation by fw */
+ err = ixgbe_aci_get_link_info(hw, activate, NULL);
+ if (err)
+ return err;
+
+ return 0;
+}
+
+/**
+ * ixgbe_get_media_type_e610 - Gets media type
+ * @hw: pointer to the HW struct
+ *
+ * In order to get the media type, the function gets PHY
+ * capabilities and later on use them to identify the PHY type
+ * checking phy_type_high and phy_type_low.
+ *
+ * Return: the type of media in form of ixgbe_media_type enum
+ * or ixgbe_media_type_unknown in case of an error.
+ */
+enum ixgbe_media_type ixgbe_get_media_type_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data pcaps;
+ int rc;
+
+ rc = ixgbe_update_link_info(hw);
+ if (rc)
+ return ixgbe_media_type_unknown;
+
+ /* If there is no link but PHY (dongle) is available SW should use
+ * Get PHY Caps admin command instead of Get Link Status, find most
+ * significant bit that is set in PHY types reported by the command
+ * and use it to discover media type.
+ */
+ if (!(hw->link.link_info.link_info & IXGBE_ACI_LINK_UP) &&
+ (hw->link.link_info.link_info & IXGBE_ACI_MEDIA_AVAILABLE)) {
+ int highest_bit;
+
+ /* Get PHY Capabilities */
+ rc = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_TOPO_CAP_MEDIA,
+ &pcaps);
+ if (rc)
+ return ixgbe_media_type_unknown;
+
+ highest_bit = fls64(pcaps.phy_type_high);
+ if (highest_bit) {
+ hw->link.link_info.phy_type_high =
+ BIT_ULL(highest_bit - 1);
+ hw->link.link_info.phy_type_low = 0;
+ } else {
+ highest_bit = fls64(pcaps.phy_type_low);
+ if (highest_bit)
+ hw->link.link_info.phy_type_low =
+ BIT_ULL(highest_bit - 1);
+ }
+
+ /* Based on search above try to discover media type */
+ hw->phy.media_type = ixgbe_get_media_type_from_phy_type(hw);
+ }
+
+ return hw->phy.media_type;
+}
+
+/**
+ * ixgbe_setup_link_e610 - Set up link
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait: true when waiting for completion is needed
+ *
+ * Set up the link with the specified speed.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_setup_link_e610(struct ixgbe_hw *hw, ixgbe_link_speed speed,
+ bool autoneg_wait)
+{
+ /* Simply request FW to perform proper PHY setup */
+ return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait);
+}
+
+/**
+ * ixgbe_check_link_e610 - Determine link and speed status
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @link_up: true when link is up
+ * @link_up_wait_to_complete: bool used to wait for link up or not
+ *
+ * Determine if the link is up and the current link speed
+ * using ACI command (0x0607).
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_check_link_e610(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
+ bool *link_up, bool link_up_wait_to_complete)
+{
+ int err;
+ u32 i;
+
+ if (!speed || !link_up)
+ return -EINVAL;
+
+ /* Set get_link_info flag to ensure that fresh
+ * link information will be obtained from FW
+ * by sending Get Link Status admin command.
+ */
+ hw->link.get_link_info = true;
+
+ /* Update link information in adapter context. */
+ err = ixgbe_get_link_status(hw, link_up);
+ if (err)
+ return err;
+
+ /* Wait for link up if it was requested. */
+ if (!link_up_wait_to_complete && *link_up) {
+ for (i = 0; i < hw->mac.max_link_up_time; i++) {
+ msleep(100);
+ hw->link.get_link_info = true;
+ err = ixgbe_get_link_status(hw, link_up);
+ if (err)
+ return err;
+ if (*link_up)
+ break;
+ }
+ }
+
+ /* Use link information in adapter context updated by the call
+ * to ixgbe_get_link_status() to determine current link speed.
+ * Link speed information is valid only when link up was
+ * reported by FW.
+ */
+ if (*link_up) {
+ switch (hw->link.link_info.link_speed) {
+ case IXGBE_ACI_LINK_SPEED_10MB:
+ *speed = IXGBE_LINK_SPEED_10_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_100MB:
+ *speed = IXGBE_LINK_SPEED_100_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_1000MB:
+ *speed = IXGBE_LINK_SPEED_1GB_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_2500MB:
+ *speed = IXGBE_LINK_SPEED_2_5GB_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_5GB:
+ *speed = IXGBE_LINK_SPEED_5GB_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_10GB:
+ *speed = IXGBE_LINK_SPEED_10GB_FULL;
+ break;
+ default:
+ *speed = IXGBE_LINK_SPEED_UNKNOWN;
+ break;
+ }
+ } else {
+ *speed = IXGBE_LINK_SPEED_UNKNOWN;
+ }
+
+ return 0;
+}
+
+/**
+ * ixgbe_get_link_capabilities_e610 - Determine link capabilities
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @autoneg: true when autoneg or autotry is enabled
+ *
+ * Determine speed and AN parameters of a link.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_get_link_capabilities_e610(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg)
+{
+ if (!speed || !autoneg)
+ return -EINVAL;
+
+ *autoneg = true;
+ *speed = hw->phy.speeds_supported;
+
+ return 0;
+}
+
+/**
+ * ixgbe_cfg_phy_fc - Configure PHY Flow Control (FC) data based on FC mode
+ * @hw: pointer to hardware structure
+ * @cfg: PHY configuration data to set FC mode
+ * @req_mode: FC mode to configure
+ *
+ * Configures PHY Flow Control according to the provided configuration.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_cfg_phy_fc(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_set_phy_cfg_data *cfg,
+ enum ixgbe_fc_mode req_mode)
+{
+ u8 pause_mask = 0x0;
+
+ if (!cfg)
+ return -EINVAL;
+
+ switch (req_mode) {
+ case ixgbe_fc_full:
+ pause_mask |= IXGBE_ACI_PHY_EN_TX_LINK_PAUSE;
+ pause_mask |= IXGBE_ACI_PHY_EN_RX_LINK_PAUSE;
+ break;
+ case ixgbe_fc_rx_pause:
+ pause_mask |= IXGBE_ACI_PHY_EN_RX_LINK_PAUSE;
+ break;
+ case ixgbe_fc_tx_pause:
+ pause_mask |= IXGBE_ACI_PHY_EN_TX_LINK_PAUSE;
+ break;
+ default:
+ break;
+ }
+
+ /* Clear the old pause settings. */
+ cfg->caps &= ~(IXGBE_ACI_PHY_EN_TX_LINK_PAUSE |
+ IXGBE_ACI_PHY_EN_RX_LINK_PAUSE);
+
+ /* Set the new capabilities. */
+ cfg->caps |= pause_mask;
+
+ return 0;
+}
+
+/**
+ * ixgbe_setup_fc_e610 - Set up flow control
+ * @hw: pointer to hardware structure
+ *
+ * Set up flow control. This has to be done during init time.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_setup_fc_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data pcaps = { 0 };
+ struct ixgbe_aci_cmd_set_phy_cfg_data cfg = { 0 };
+ int err;
+
+ /* Get the current PHY config */
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_ACTIVE_CFG, &pcaps);
+ if (err)
+ return err;
+
+ ixgbe_copy_phy_caps_to_cfg(&pcaps, &cfg);
+
+ /* Configure the set PHY data */
+ err = ixgbe_cfg_phy_fc(hw, &cfg, hw->fc.requested_mode);
+ if (err)
+ return err;
+
+ /* If the capabilities have changed, then set the new config */
+ if (cfg.caps != pcaps.caps) {
+ cfg.caps |= IXGBE_ACI_PHY_ENA_AUTO_LINK_UPDT;
+
+ err = ixgbe_aci_set_phy_cfg(hw, &cfg);
+ if (err)
+ return err;
+ }
+
+ return err;
+}
+
+/**
+ * ixgbe_fc_autoneg_e610 - Configure flow control
+ * @hw: pointer to hardware structure
+ *
+ * Configure Flow Control.
+ */
+void ixgbe_fc_autoneg_e610(struct ixgbe_hw *hw)
+{
+ int err;
+
+ /* Get current link err.
+ * Current FC mode will be stored in the hw context.
+ */
+ err = ixgbe_aci_get_link_info(hw, false, NULL);
+ if (err)
+ goto out;
+
+ /* Check if the link is up */
+ if (!(hw->link.link_info.link_info & IXGBE_ACI_LINK_UP)) {
+ err = -EIO;
+ goto out;
+ }
+
+ /* Check if auto-negotiation has completed */
+ if (!(hw->link.link_info.an_info & IXGBE_ACI_AN_COMPLETED)) {
+ err = -EIO;
+ goto out;
+ }
+
+out:
+ if (!err) {
+ hw->fc.fc_was_autonegged = true;
+ } else {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ }
+}
+
+/**
+ * ixgbe_disable_rx_e610 - Disable RX unit
+ * @hw: pointer to hardware structure
+ *
+ * Disable RX DMA unit on E610 with use of ACI command (0x000C).
+ *
+ * Return: the exit code of the operation.
+ */
+void ixgbe_disable_rx_e610(struct ixgbe_hw *hw)
+{
+ u32 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
+
+ if (rxctrl & IXGBE_RXCTRL_RXEN) {
+ u32 pfdtxgswc;
+ int err;
+
+ pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
+ if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) {
+ pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN;
+ IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
+ hw->mac.set_lben = true;
+ } else {
+ hw->mac.set_lben = false;
+ }
+
+ err = ixgbe_aci_disable_rxen(hw);
+
+ /* If we fail - disable RX using register write */
+ if (err) {
+ rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
+ if (rxctrl & IXGBE_RXCTRL_RXEN) {
+ rxctrl &= ~IXGBE_RXCTRL_RXEN;
+ IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl);
+ }
+ }
+ }
+}
+
+/**
+ * ixgbe_init_phy_ops_e610 - PHY specific init
+ * @hw: pointer to hardware structure
+ *
+ * Initialize any function pointers that were not able to be
+ * set during init_shared_code because the PHY type was not known.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_init_phy_ops_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+ struct ixgbe_phy_info *phy = &hw->phy;
+ int ret_val;
+
+ if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper)
+ phy->ops.set_phy_power = ixgbe_set_phy_power_e610;
+ else
+ phy->ops.set_phy_power = NULL;
+
+ /* Identify the PHY */
+ ret_val = phy->ops.identify(hw);
+ if (ret_val)
+ return ret_val;
+
+ return ret_val;
+}
+
+/**
+ * ixgbe_identify_phy_e610 - Identify PHY
+ * @hw: pointer to hardware structure
+ *
+ * Determine PHY type, supported speeds and PHY ID.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_identify_phy_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data pcaps;
+ int err;
+
+ /* Set PHY type */
+ hw->phy.type = ixgbe_phy_fw;
+
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_TOPO_CAP_MEDIA, &pcaps);
+ if (err)
+ return err;
+
+ if (!(pcaps.module_compliance_enforcement &
+ IXGBE_ACI_MOD_ENFORCE_STRICT_MODE)) {
+ /* Handle lenient mode */
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_TOPO_CAP_NO_MEDIA,
+ &pcaps);
+ if (err)
+ return err;
+ }
+
+ /* Determine supported speeds */
+ hw->phy.speeds_supported = IXGBE_LINK_SPEED_UNKNOWN;
+
+ if (pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_10BASE_T ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_10M_SGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_10_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_100BASE_TX ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_100M_SGMII ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_100M_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_100_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1000BASE_T ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1000BASE_SX ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1000BASE_LX ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1000BASE_KX ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1G_SGMII ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_1G_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_1GB_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_2500BASE_T ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_2500BASE_X ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_2500BASE_KX ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_2500M_SGMII ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_2500M_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_2_5GB_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_5GBASE_T ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_5GBASE_KR ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_5G_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_5GB_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10GBASE_T ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10G_SFI_DA ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10GBASE_SR ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10GBASE_LR ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10GBASE_KR_CR1 ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10G_SFI_AOC_ACC ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10G_SFI_C2C ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_10G_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_10GB_FULL;
+
+ /* Initialize autoneg speeds */
+ if (!hw->phy.autoneg_advertised)
+ hw->phy.autoneg_advertised = hw->phy.speeds_supported;
+
+ /* Set PHY ID */
+ memcpy(&hw->phy.id, pcaps.phy_id_oui, sizeof(u32));
+
+ hw->phy.eee_speeds_supported = IXGBE_LINK_SPEED_10_FULL |
+ IXGBE_LINK_SPEED_100_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ hw->phy.eee_speeds_advertised = hw->phy.eee_speeds_supported;
+
+ return 0;
+}
+
+/**
+ * ixgbe_identify_module_e610 - Identify SFP module type
+ * @hw: pointer to hardware structure
+ *
+ * Identify the SFP module type.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_identify_module_e610(struct ixgbe_hw *hw)
+{
+ bool media_available;
+ u8 module_type;
+ int err;
+
+ err = ixgbe_update_link_info(hw);
+ if (err)
+ goto err;
+
+ media_available =
+ (hw->link.link_info.link_info & IXGBE_ACI_MEDIA_AVAILABLE);
+
+ if (media_available) {
+ hw->phy.sfp_type = ixgbe_sfp_type_unknown;
+
+ /* Get module type from hw context updated by
+ * ixgbe_update_link_info()
+ */
+ module_type = hw->link.link_info.module_type[IXGBE_ACI_MOD_TYPE_IDENT];
+
+ if ((module_type & IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_PASSIVE) ||
+ (module_type & IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_ACTIVE)) {
+ hw->phy.sfp_type = ixgbe_sfp_type_da_cu;
+ } else if (module_type & IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_SR) {
+ hw->phy.sfp_type = ixgbe_sfp_type_sr;
+ } else if ((module_type & IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_LR) ||
+ (module_type & IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_LRM)) {
+ hw->phy.sfp_type = ixgbe_sfp_type_lr;
+ }
+ err = 0;
+ } else {
+ hw->phy.sfp_type = ixgbe_sfp_type_not_present;
+ err = -ENOENT;
+ }
+err:
+ return err;
+}
+
+/**
+ * ixgbe_setup_phy_link_e610 - Sets up firmware-controlled PHYs
+ * @hw: pointer to hardware structure
+ *
+ * Set the parameters for the firmware-controlled PHYs.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_setup_phy_link_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data pcaps;
+ struct ixgbe_aci_cmd_set_phy_cfg_data pcfg;
+ int err;
+
+ err = ixgbe_aci_get_link_info(hw, false, NULL);
+ if (err)
+ goto err;
+
+ /* Set PHY Configuration only if media is available */
+ if (!(hw->link.link_info.link_info & IXGBE_ACI_MEDIA_AVAILABLE)) {
+ err = ixgbe_aci_set_link_restart_an(hw, false);
+ if (err)
+ goto err;
+
+ return 0;
+ }
+
+ err = ixgbe_aci_get_phy_caps(hw, false, IXGBE_ACI_REPORT_DFLT_CFG,
+ &pcaps);
+ if (err)
+ goto err;
+
+ ixgbe_copy_phy_caps_to_cfg(&pcaps, &pcfg);
+
+ pcfg.caps |= IXGBE_ACI_PHY_ENA_LINK;
+ pcfg.caps |= IXGBE_ACI_PHY_ENA_AUTO_LINK_UPDT;
+
+ /* Set default PHY types for a given speed */
+ pcfg.phy_type_low = 0;
+ pcfg.phy_type_high = 0;
+
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10_FULL) {
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_10BASE_T;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_10M_SGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_100BASE_TX;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_100M_SGMII;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_100M_USXGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1000BASE_T;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1000BASE_SX;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1000BASE_LX;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1000BASE_KX;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1G_SGMII;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_1G_USXGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_2_5GB_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_2500BASE_T;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_2500BASE_X;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_2500BASE_KX;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_2500M_SGMII;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_2500M_USXGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_5GB_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_5GBASE_T;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_5GBASE_KR;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_5G_USXGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10GB_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10GBASE_T;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10G_SFI_DA;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10GBASE_SR;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10GBASE_LR;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10GBASE_KR_CR1;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10G_SFI_AOC_ACC;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10G_SFI_C2C;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_10G_USXGMII;
+ }
+
+ /* Mask the set values to avoid requesting unsupported link types */
+ pcfg.phy_type_low &= pcaps.phy_type_low;
+ pcfg.phy_type_high &= pcaps.phy_type_high;
+
+ err = ixgbe_aci_set_phy_cfg(hw, &pcfg);
+ if (err)
+ goto err;
+
+ /* Request link restart - without putting it down */
+ err = ixgbe_aci_set_link_restart_an(hw, true);
+ if (err)
+ goto err;
+
+err:
+ return err;
+}
+
+/**
+ * ixgbe_set_phy_power_e610 - Control power for copper PHY
+ * @hw: pointer to hardware structure
+ * @on: true for on, false for off
+ *
+ * Set the power on/off of the PHY
+ * by getting its capabilities and setting the appropriate
+ * configuration parameters.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_set_phy_power_e610(struct ixgbe_hw *hw, bool on)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data phy_caps = { 0 };
+ struct ixgbe_aci_cmd_set_phy_cfg_data phy_cfg = { 0 };
+ int err;
+
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_ACTIVE_CFG,
+ &phy_caps);
+ if (err)
+ return err;
+
+ ixgbe_copy_phy_caps_to_cfg(&phy_caps, &phy_cfg);
+
+ if (on)
+ phy_cfg.caps &= ~IXGBE_ACI_PHY_ENA_LOW_POWER;
+ else
+ phy_cfg.caps |= IXGBE_ACI_PHY_ENA_LOW_POWER;
+
+ phy_cfg.caps |= IXGBE_ACI_PHY_ENA_LINK;
+ phy_cfg.caps |= IXGBE_ACI_PHY_ENA_AUTO_LINK_UPDT;
+
+ err = ixgbe_aci_set_phy_cfg(hw, &phy_cfg);
+
+ return err;
+}
+
+/**
+ * ixgbe_enter_lplu_e610 - Transition to low power states
+ * @hw: pointer to hardware structure
+ *
+ * Configures Low Power Link Up on transition to low power states
+ * (from D0 to non-D0). Link is required to enter LPLU so avoid resetting the
+ * X557 PHY immediately prior to entering LPLU.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_enter_lplu_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data phy_caps = { 0 };
+ struct ixgbe_aci_cmd_set_phy_cfg_data phy_cfg = { 0 };
+ int err;
+
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_ACTIVE_CFG,
+ &phy_caps);
+ if (err)
+ return err;
+
+ ixgbe_copy_phy_caps_to_cfg(&phy_caps, &phy_cfg);
+
+ phy_cfg.low_power_ctrl_an |= IXGBE_ACI_PHY_EN_D3COLD_LOW_POWER_AUTONEG;
+
+ err = ixgbe_aci_set_phy_cfg(hw, &phy_cfg);
+
+ return err;
+}
+
+/**
+ * ixgbe_aci_get_netlist_node - get a node handle
+ * @hw: pointer to the hw struct
+ * @cmd: get_link_topo AQ structure
+ * @node_part_number: output node part number if node found
+ * @node_handle: output node handle parameter if node found
+ *
+ * Get the netlist node and assigns it to
+ * the provided handle using ACI command (0x06E0).
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_get_netlist_node(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_get_link_topo *cmd,
+ u8 *node_part_number, u16 *node_handle)
+{
+ struct ixgbe_aci_desc desc;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_get_link_topo);
+ desc.params.get_link_topo = *cmd;
+
+ if (ixgbe_aci_send_cmd(hw, &desc, NULL, 0))
+ return -EOPNOTSUPP;
+
+ if (node_handle)
+ *node_handle = desc.params.get_link_topo.addr.handle;
+ if (node_part_number)
+ *node_part_number = desc.params.get_link_topo.node_part_num;
+
+ return 0;
+}
@@ -26,5 +26,37 @@ int ixgbe_aci_get_phy_caps(struct ixgbe_hw *hw, bool qual_mods, u8 report_mode,
struct ixgbe_aci_cmd_get_phy_caps_data *pcaps);
void ixgbe_copy_phy_caps_to_cfg(struct ixgbe_aci_cmd_get_phy_caps_data *caps,
struct ixgbe_aci_cmd_set_phy_cfg_data *cfg);
+int ixgbe_aci_set_phy_cfg(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_set_phy_cfg_data *cfg);
+int ixgbe_aci_set_link_restart_an(struct ixgbe_hw *hw, bool ena_link);
+int ixgbe_update_link_info(struct ixgbe_hw *hw);
+int ixgbe_get_link_status(struct ixgbe_hw *hw, bool *link_up);
+int ixgbe_aci_get_link_info(struct ixgbe_hw *hw, bool ena_lse,
+ struct ixgbe_link_status *link);
+int ixgbe_aci_set_event_mask(struct ixgbe_hw *hw, u8 port_num, u16 mask);
+int ixgbe_configure_lse(struct ixgbe_hw *hw, bool activate, u16 mask);
+enum ixgbe_media_type ixgbe_get_media_type_e610(struct ixgbe_hw *hw);
+int ixgbe_setup_link_e610(struct ixgbe_hw *hw, ixgbe_link_speed speed,
+ bool autoneg_wait);
+int ixgbe_check_link_e610(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
+ bool *link_up, bool link_up_wait_to_complete);
+int ixgbe_get_link_capabilities_e610(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg);
+int ixgbe_cfg_phy_fc(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_set_phy_cfg_data *cfg,
+ enum ixgbe_fc_mode req_mode);
+int ixgbe_setup_fc_e610(struct ixgbe_hw *hw);
+void ixgbe_fc_autoneg_e610(struct ixgbe_hw *hw);
+void ixgbe_disable_rx_e610(struct ixgbe_hw *hw);
+int ixgbe_init_phy_ops_e610(struct ixgbe_hw *hw);
+int ixgbe_identify_phy_e610(struct ixgbe_hw *hw);
+int ixgbe_identify_module_e610(struct ixgbe_hw *hw);
+int ixgbe_setup_phy_link_e610(struct ixgbe_hw *hw);
+int ixgbe_set_phy_power_e610(struct ixgbe_hw *hw, bool on);
+int ixgbe_enter_lplu_e610(struct ixgbe_hw *hw);
+int ixgbe_aci_get_netlist_node(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_get_link_topo *cmd,
+ u8 *node_part_number, u16 *node_handle);
#endif /* _IXGBE_E610_H_ */
@@ -647,6 +647,7 @@ struct ixgbe_aci_cmd_link_topo_params {
#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_CLK_MUX 10
#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_GPS 11
#define IXGBE_ACI_LINK_TOPO_NODE_CTX_S 4
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_M GENMASK(7, 4)
#define IXGBE_ACI_LINK_TOPO_NODE_CTX_GLOBAL 0
#define IXGBE_ACI_LINK_TOPO_NODE_CTX_BOARD 1
#define IXGBE_ACI_LINK_TOPO_NODE_CTX_PORT 2