@@ -79,6 +79,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-jethome-jethub-j200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l-ts050.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-sm1-s905d3-libretech-cc.dtb
new file mode 100644
@@ -0,0 +1,614 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 JetHome
+ * Author: Viacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1.dtsi"
+
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+
+/ {
+
+ compatible = "jethome,jethub-j200", "amlogic,sm1";
+ model = "JetHome JetHub D2";
+
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ rtc0 = &rtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ tflash_vdd: regulator-tflash_vdd {
+ compatible = "regulator-fixed";
+
+ regulator-name = "TFLASH_VDD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio_ao GPIOAO_3 GPIO_OPEN_DRAIN>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ tf_io: gpio-regulator-tf_io {
+ compatible = "regulator-gpio";
+
+ regulator-name = "TF_IO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_5v>;
+
+ enable-gpios = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
+ enable-active-high;
+ regulator-always-on;
+
+ gpios = <&gpio_ao GPIOAO_6 GPIO_OPEN_SOURCE>;
+ gpios-states = <0>;
+
+ states = <3300000 0>,
+ <1800000 1>;
+ };
+
+ flash_1v8: regulator-flash_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "FLASH_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ main_12v: regulator-main_12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&main_12v>;
+ gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+ enable-active-high;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddcpu: regulator-vddcpu {
+ /*
+ * MP8756GD Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ pwm-supply = <&main_12v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ usb_pwr_en: regulator-usb_pwr_en {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR_EN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ /* Connected to the microUSB port power enable */
+ gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ audio-aux-devs = <&tdmout_b>;
+ audio-routing = "TDM_B Playback", "TDMOUT_B OUT";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+
+ /* 8ch hdmi interface */
+ dai-link-0 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ /* hdmi glue */
+ dai-link-1 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ panic-indicator;
+ };
+
+ led-red {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ };
+
+ sound {
+ model = "JETHUB-D2";
+ };
+
+ usb-hub {
+ dr_mode = "host";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* USB 2.0 hub with reset gpio */
+ hub_2_0: hub@1 {
+ compatible = "usb5e3,610";
+ reg = <1>;
+ reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&vcc_5v>;
+ };
+ };
+
+};
+
+&arb {
+ status = "okay";
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU1_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu2 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU2_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu3 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU3_CLK>;
+ clock-latency = <50000>;
+};
+
+&ext_mdio {
+ external_phy: ethernet-phy@0 {
+ /* Realtek RTL8211F (0x001cc916) */
+ reg = <0>;
+ max-speed = <1000>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <80000>;
+ reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_14 */
+ interrupts = <IRQID_GPIOZ_14 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+ðmac {
+ pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&external_phy>;
+ amlogic,tx-delay-ns = <2>;
+};
+
+&gpio {
+ gpio-line-names =
+ /* GPIOZ */
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ /* GPIOH */
+ "", "", "", "", "",
+ "LED_RED", /* GPIOH_5 */
+ "I2C_SDA_MODULES", /* GPIOH_6 */
+ "I2C_SCL_MODULES", /* GPIOH_7 */
+ "",
+ /* BOOT */
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ /* GPIOC */
+ "", "", "", "", "", "", "", "",
+ /* GPIOA */
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "",
+ "I2C_SDA_SYSBUS", /* GPIOA_14 */
+ "I2C_SCL_SYSBUS", /* GPIOA_15 */
+ /* GPIOX */
+ "", /* GPIOX_0 */
+ "", /* GPIOX_1 */
+ "", /* GPIOX_2 */
+ "", /* GPIOX_3 */
+ "", /* GPIOX_4 */
+ "", /* GPIOX_5 */
+ "RS485_TX", /* GPIOX_6 */
+ "RS485_RX", /* GPIOX_7 */
+ "", /* GPIOX_8 */
+ "", /* GPIOX_9 */
+ "", /* GPIOX_10 */
+ "", /* GPIOX_11 */
+ "", /* GPIOX_12 */
+ "", /* GPIOX_13 */
+ "", /* GPIOX_14 */
+ "", /* GPIOX_15 */
+ "", /* GPIOX_16 */
+ "I2C_SDA_LCDBUS", /* GPIOX_17 */
+ "I2C_SCL_LCDBUS", /* GPIOX_18 */
+ ""; /* GPIOX_19 */
+};
+
+&gpio_ao {
+ gpio-line-names =
+ /* GPIOAO */
+ "", "", "", "",
+ "MCU_RESET", /* GPIOAO_4 */
+ "POWER_GOOD", /* GPIOAO_5 */
+ "",
+ "MCU_BOOT", /* GPIOAO_7 */
+ "MCU_UART_TX", /* GPIOAO_8 */
+ "MCU_UART_RX", /* GPIOAO_9 */
+ "BUTTON_USR", /* GPIOAO_10 */
+ "LED_GREEN", /* GPIOAO_11 */
+ /* GPIOE */
+ "", "", "";
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>; // GPIOE_1
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <200000000>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&tflash_vdd>;
+ vqmmc-supply = <&tf_io>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&flash_1v8>;
+};
+
+&spifc {
+ status = "disabled";
+ pinctrl-0 = <&nor_pins>;
+ pinctrl-names = "default";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <104000000>;
+ };
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_8_9_pins>;
+ pinctrl-names = "default";
+};
+
+&uart_B {
+ status = "okay";
+ pinctrl-0 = <&uart_b_pins>;
+ pinctrl-names = "default";
+};
+
+
+&usb {
+ status = "okay";
+ vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+ phy-supply = <&vcc_5v>;
+};
+
+
+/* I2C for modules */
+&i2c1 {
+ status = "okay";
+ pinctrl-0 = <&i2c1_sda_h6_pins>, <&i2c1_sck_h7_pins>;
+ pinctrl-names = "default";
+
+ /* GPIO expander */
+ u9: gpio@22 {
+ compatible = "nxp,pca9535";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "RELAY_1", "RELAY_2",
+ "", "",
+ "UXM1_RESET", "UXM1_BOOT",
+ "UXM2_RESET", "UXM2_BOOT",
+ "DIN_1", "DIN_2", "DIN_3",
+ "","","","","";
+ };
+
+ /* 1-wire */
+ w1: onewire@18 {
+ compatible = "maxim,ds2482";
+ reg = <0x18>;
+ };
+
+};
+
+
+/* I2C for lcd/etc */
+&i2c2 {
+ status = "okay";
+ pinctrl-0 = <&i2c2_sda_x_pins>, <&i2c2_sck_x_pins>;
+ pinctrl-names = "default";
+};
+
+/* I2C_EE_M3: I2C for CPU board */
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+
+ /* I2C for rtc */
+ rtc: rtc@51 {
+ status = "okay";
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ wakeup-source;
+ };
+
+ /* FRAM on base board */
+ fram: eeprom@52 {
+ compatible = "atmel,24c64";
+ reg = <0x52>;
+ pagesize = <0x20>;
+ label = "fram";
+ address-width = <0x10>;
+ vcc-supply = <&vddao_3v3>;
+ };
+
+ /* EEPROM on CPU board */
+ eepromc: eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ pagesize = <0x20>;
+ label = "eepromc";
+ address-width = <0x10>;
+ vcc-supply = <&vddao_3v3>;
+ };
+
+ /* EEPROM on base board */
+ eeprompd: eeprom@56 {
+ compatible = "atmel,24c64";
+ reg = <0x56>;
+ pagesize = <0x20>;
+ label = "eeprompd";
+ address-width = <0x10>;
+ vcc-supply = <&vddao_3v3>;
+ };
+
+ /* EEPROM on power module */
+ eeprompm: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <0x20>;
+ label = "eeprompm";
+ address-width = <0x10>;
+ vcc-supply = <&vddao_3v3>;
+ };
+
+ /* temperature sensors */
+ temp1: tmp102@48 {
+ compatible = "ti,tmp102";
+ reg = <0x48>;
+ };
+
+ temp2: tmp102@49 {
+ compatible = "ti,tmp102";
+ reg = <0x49>;
+ };
+
+};
JetHome Jethub D2 is a home automation controller with the following features: - DIN Rail Mounting - Amlogic S905X3 (ARM Cortex-A55) quad-core - micro-HDMI video out - 4GB LPDDR4 - 32GB eMMC flash - 1 x USB 2.0 - 1 x 10/100/1000Mbps ethernet - two module slots for radio/wire interface cards - 2 x gpio LEDS - 1 x 1-Wire - 1 x RS-485 - 3 x dry contact digital GPIO inputs - 2 x relay GPIO outputs - DC 9-36V power source with battery UPS on board option Signed-off-by: Viacheslav Bocharov <adeep@lexina.in> --- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../amlogic/meson-sm1-jethome-jethub-j200.dts | 614 ++++++++++++++++++ 2 files changed, 615 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-jethome-jethub-j200.dts