diff mbox series

[net-next,2/2] net: stmmac: dwmac-stm32: stm32: add management of stm32mp25 for stm32

Message ID 20240614130812.72425-3-christophe.roullier@foss.st.com (mailing list archive)
State Superseded
Delegated to: Netdev Maintainers
Headers show
Series Series to deliver Ethernet for STM32MP25 | expand

Checks

Context Check Description
netdev/series_format success Posting correctly formatted
netdev/tree_selection success Clearly marked for net-next
netdev/ynl success Generated files up to date; no warnings/errors; no diff in generated;
netdev/fixes_present success Fixes tag not required for -next series
netdev/header_inline success No static functions without inline keyword in header files
netdev/build_32bit success Errors and warnings before: 845 this patch: 845
netdev/build_tools success No tools touched, skip
netdev/cc_maintainers success CCed 9 of 9 maintainers
netdev/build_clang success Errors and warnings before: 849 this patch: 849
netdev/verify_signedoff success Signed-off-by tag matches author and committer
netdev/deprecated_api success None detected
netdev/check_selftest success No net selftest shell script
netdev/verify_fixes success No Fixes tag
netdev/build_allmodconfig_warn success Errors and warnings before: 849 this patch: 849
netdev/checkpatch warning WARNING: line length of 88 exceeds 80 columns
netdev/build_clang_rust success No Rust files in patch. Skipping build
netdev/kdoc success Errors and warnings before: 0 this patch: 0
netdev/source_inline success Was 0 now: 0
netdev/contest success net-next-2024-06-14--21-00 (tests: 650)

Commit Message

Christophe Roullier June 14, 2024, 1:08 p.m. UTC
Add Ethernet support for STM32MP25.
STM32MP25 is STM32 SOC with 2 GMACs instances.
GMAC IP version is SNPS 5.3x.
GMAC IP configure with 2 RX and 4 TX queue.
DMA HW capability register supported
RX Checksum Offload Engine supported
TX Checksum insertion supported
Wake-Up On Lan supported
TSO supported

Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 121 +++++++++++++++---
 1 file changed, 104 insertions(+), 17 deletions(-)

Comments

Marek Vasut June 14, 2024, 1:58 p.m. UTC | #1
On 6/14/24 3:08 PM, Christophe Roullier wrote:

[...]

> +static int stm32mp2_configure_syscfg(struct plat_stmmacenet_data *plat_dat)
> +{
> +	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
> +	u32 reg = dwmac->mode_reg;
> +	int val = 0;
> +
> +	switch (plat_dat->mac_interface) {
> +	case PHY_INTERFACE_MODE_MII:
> +		break;

dwmac->enable_eth_ck does not apply to MII mode ? Why ?

> +	case PHY_INTERFACE_MODE_GMII:
> +		if (dwmac->enable_eth_ck)
> +			val |= SYSCFG_ETHCR_ETH_CLK_SEL;
> +		break;
> +	case PHY_INTERFACE_MODE_RMII:
> +		val = SYSCFG_ETHCR_ETH_SEL_RMII;
> +		if (dwmac->enable_eth_ck)
> +			val |= SYSCFG_ETHCR_ETH_REF_CLK_SEL;
> +		break;
> +	case PHY_INTERFACE_MODE_RGMII:
> +	case PHY_INTERFACE_MODE_RGMII_ID:
> +	case PHY_INTERFACE_MODE_RGMII_RXID:
> +	case PHY_INTERFACE_MODE_RGMII_TXID:
> +		val = SYSCFG_ETHCR_ETH_SEL_RGMII;
> +		if (dwmac->enable_eth_ck)
> +			val |= SYSCFG_ETHCR_ETH_CLK_SEL;
> +		break;
> +	default:
> +		dev_err(dwmac->dev, "Mode %s not supported",
> +			phy_modes(plat_dat->mac_interface));
> +		/* Do not manage others interfaces */
> +		return -EINVAL;
> +	}
> +
> +	dev_dbg(dwmac->dev, "Mode %s", phy_modes(plat_dat->mac_interface));
> +
> +	/*  select PTP (IEEE1588) clock selection from RCC (ck_ker_ethxptp) */

Drop extra leading space.
Sentence starts with capital letter.

> +	val |= SYSCFG_ETHCR_ETH_PTP_CLK_SEL;
> +
> +	/* Update ETHCR (set register) */
> +	return regmap_update_bits(dwmac->regmap, reg,
> +				 SYSCFG_MP2_ETH_MASK, val);
> +}
> +
>   static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
>   {
>   	int ret;
> @@ -292,6 +346,21 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
>   	return stm32mp1_configure_pmcr(plat_dat);
>   }
>   
> +static int stm32mp2_set_mode(struct plat_stmmacenet_data *plat_dat)
> +{
> +	int ret;
> +
> +	ret = stm32mp1_select_ethck_external(plat_dat);
> +	if (ret)
> +		return ret;
> +
> +	ret = stm32mp1_validate_ethck_rate(plat_dat);
> +	if (ret)
> +		return ret;


Is it necessary to duplicate this entire function instead of some:

if (is_mp2)
   return stm32mp2_configure_syscfg(plat_dat);
else
   return stm32mp1_configure_syscfg(plat_dat);

?

> +	return stm32mp2_configure_syscfg(plat_dat);
> +}
> +
>   static int stm32mcu_set_mode(struct plat_stmmacenet_data *plat_dat)
>   {
>   	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
> @@ -348,12 +417,6 @@ static int stm32_dwmac_parse_data(struct stm32_dwmac *dwmac,
>   		return PTR_ERR(dwmac->clk_rx);
>   	}
>   
> -	if (dwmac->ops->parse_data) {
> -		err = dwmac->ops->parse_data(dwmac, dev);
> -		if (err)
> -			return err;
> -	}
> -
>   	/* Get mode register */
>   	dwmac->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscon");
>   	if (IS_ERR(dwmac->regmap))
> @@ -365,20 +428,14 @@ static int stm32_dwmac_parse_data(struct stm32_dwmac *dwmac,
>   		return err;
>   	}
>   
> -	dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
> -	err = of_property_read_u32_index(np, "st,syscon", 2, &dwmac->mode_mask);
> -	if (err) {
> -		if (dwmac->ops->is_mp13)
> -			dev_err(dev, "Sysconfig register mask must be set (%d)\n", err);
> -		else
> -			dev_dbg(dev, "Warning sysconfig register mask not set\n");
> -	}
> +	if (dwmac->ops->parse_data)
> +		err = dwmac->ops->parse_data(dwmac, dev);

Why is this change here ? What is the purpose ?
This should be documented in commit message too.

The indirect call is not necessary either, simply do

if (is_mp2)
   return err;

... do mp15/13 stuff here ...

return err;

[...]
Christophe Roullier June 17, 2024, 11:23 a.m. UTC | #2
Hi Marek,

On 6/14/24 15:58, Marek Vasut wrote:
> On 6/14/24 3:08 PM, Christophe Roullier wrote:
>
> [...]
>
>> +static int stm32mp2_configure_syscfg(struct plat_stmmacenet_data 
>> *plat_dat)
>> +{
>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>> +    u32 reg = dwmac->mode_reg;
>> +    int val = 0;
>> +
>> +    switch (plat_dat->mac_interface) {
>> +    case PHY_INTERFACE_MODE_MII:
>> +        break;
>
> dwmac->enable_eth_ck does not apply to MII mode ? Why ?

It is like MP1 and MP13, nothing to set in syscfg register for case MII 
mode wo crystal.

>
>> +    case PHY_INTERFACE_MODE_GMII:
>> +        if (dwmac->enable_eth_ck)
>> +            val |= SYSCFG_ETHCR_ETH_CLK_SEL;
>> +        break;
>> +    case PHY_INTERFACE_MODE_RMII:
>> +        val = SYSCFG_ETHCR_ETH_SEL_RMII;
>> +        if (dwmac->enable_eth_ck)
>> +            val |= SYSCFG_ETHCR_ETH_REF_CLK_SEL;
>> +        break;
>> +    case PHY_INTERFACE_MODE_RGMII:
>> +    case PHY_INTERFACE_MODE_RGMII_ID:
>> +    case PHY_INTERFACE_MODE_RGMII_RXID:
>> +    case PHY_INTERFACE_MODE_RGMII_TXID:
>> +        val = SYSCFG_ETHCR_ETH_SEL_RGMII;
>> +        if (dwmac->enable_eth_ck)
>> +            val |= SYSCFG_ETHCR_ETH_CLK_SEL;
>> +        break;
>> +    default:
>> +        dev_err(dwmac->dev, "Mode %s not supported",
>> +            phy_modes(plat_dat->mac_interface));
>> +        /* Do not manage others interfaces */
>> +        return -EINVAL;
>> +    }
>> +
>> +    dev_dbg(dwmac->dev, "Mode %s", phy_modes(plat_dat->mac_interface));
>> +
>> +    /*  select PTP (IEEE1588) clock selection from RCC 
>> (ck_ker_ethxptp) */
>
> Drop extra leading space.
> Sentence starts with capital letter.
ok
>
>> +    val |= SYSCFG_ETHCR_ETH_PTP_CLK_SEL;
>> +
>> +    /* Update ETHCR (set register) */
>> +    return regmap_update_bits(dwmac->regmap, reg,
>> +                 SYSCFG_MP2_ETH_MASK, val);
>> +}
>> +
>>   static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
>>   {
>>       int ret;
>> @@ -292,6 +346,21 @@ static int stm32mp1_set_mode(struct 
>> plat_stmmacenet_data *plat_dat)
>>       return stm32mp1_configure_pmcr(plat_dat);
>>   }
>>   +static int stm32mp2_set_mode(struct plat_stmmacenet_data *plat_dat)
>> +{
>> +    int ret;
>> +
>> +    ret = stm32mp1_select_ethck_external(plat_dat);
>> +    if (ret)
>> +        return ret;
>> +
>> +    ret = stm32mp1_validate_ethck_rate(plat_dat);
>> +    if (ret)
>> +        return ret;
>
>
> Is it necessary to duplicate this entire function instead of some:
>
> if (is_mp2)
>   return stm32mp2_configure_syscfg(plat_dat);
> else
>   return stm32mp1_configure_syscfg(plat_dat);
>
> ?
ok I would like to avoid to use is_mp2 boolean but you are right it is 
simplify visibility of the code.
>
>> +    return stm32mp2_configure_syscfg(plat_dat);
>> +}
>> +
>>   static int stm32mcu_set_mode(struct plat_stmmacenet_data *plat_dat)
>>   {
>>       struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>> @@ -348,12 +417,6 @@ static int stm32_dwmac_parse_data(struct 
>> stm32_dwmac *dwmac,
>>           return PTR_ERR(dwmac->clk_rx);
>>       }
>>   -    if (dwmac->ops->parse_data) {
>> -        err = dwmac->ops->parse_data(dwmac, dev);
>> -        if (err)
>> -            return err;
>> -    }
>> -
>>       /* Get mode register */
>>       dwmac->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscon");
>>       if (IS_ERR(dwmac->regmap))
>> @@ -365,20 +428,14 @@ static int stm32_dwmac_parse_data(struct 
>> stm32_dwmac *dwmac,
>>           return err;
>>       }
>>   -    dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
>> -    err = of_property_read_u32_index(np, "st,syscon", 2, 
>> &dwmac->mode_mask);
>> -    if (err) {
>> -        if (dwmac->ops->is_mp13)
>> -            dev_err(dev, "Sysconfig register mask must be set 
>> (%d)\n", err);
>> -        else
>> -            dev_dbg(dev, "Warning sysconfig register mask not set\n");
>> -    }
>> +    if (dwmac->ops->parse_data)
>> +        err = dwmac->ops->parse_data(dwmac, dev);
>
> Why is this change here ? What is the purpose ?
> This should be documented in commit message too.
>
> The indirect call is not necessary either, simply do
>
> if (is_mp2)
>   return err;
>
> ... do mp15/13 stuff here ...
>
> return err;
Right, with use of is_mp2 variable it is more simple
>
> [...]
Marek Vasut June 17, 2024, 3:57 p.m. UTC | #3
On 6/17/24 1:23 PM, Christophe ROULLIER wrote:

Hi,

>>> +static int stm32mp2_configure_syscfg(struct plat_stmmacenet_data 
>>> *plat_dat)
>>> +{
>>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>>> +    u32 reg = dwmac->mode_reg;
>>> +    int val = 0;
>>> +
>>> +    switch (plat_dat->mac_interface) {
>>> +    case PHY_INTERFACE_MODE_MII:
>>> +        break;
>>
>> dwmac->enable_eth_ck does not apply to MII mode ? Why ?
> 
> It is like MP1 and MP13, nothing to set in syscfg register for case MII 
> mode wo crystal.

Have a look at STM32MP15xx RM0436 Figure 83. Peripheral clock 
distribution for Ethernet.

If RCC (top-left corner of the figure) generates 25 MHz MII clock 
(yellow line) on eth_clk_fb (top-right corner), can I set 
ETH_REF_CLK_SEL to position '1' and ETH_SEL[2] to '0' and feed ETH 
(right side) clk_rx_i input with 25 MHz clock that way ?

I seems like this should be possible, at least theoretically. Can you 
check with the hardware/silicon people ?

As a result, the MII/RMII mode would behave in a very similar way, and 
so would GMII/RGMII mode behave in a very similar way. Effectively you 
would end up with this (notice the fallthrough statements):

+	case PHY_INTERFACE_MODE_RMII:
+		val = SYSCFG_ETHCR_ETH_SEL_RMII;
+		fallthrough;
+	case PHY_INTERFACE_MODE_MII:
+		if (dwmac->enable_eth_ck)
+			val |= SYSCFG_ETHCR_ETH_REF_CLK_SEL;
+		break;
+
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		val = SYSCFG_ETHCR_ETH_SEL_RGMII;
+		fallthrough;
+	case PHY_INTERFACE_MODE_GMII:
+		if (dwmac->enable_eth_ck)
+			val |= SYSCFG_ETHCR_ETH_CLK_SEL;
+		break;

[...]
Christophe Roullier June 18, 2024, 9:09 a.m. UTC | #4
Hi Marek,

On 6/17/24 17:57, Marek Vasut wrote:
> On 6/17/24 1:23 PM, Christophe ROULLIER wrote:
>
> Hi,
>
>>>> +static int stm32mp2_configure_syscfg(struct plat_stmmacenet_data 
>>>> *plat_dat)
>>>> +{
>>>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>>>> +    u32 reg = dwmac->mode_reg;
>>>> +    int val = 0;
>>>> +
>>>> +    switch (plat_dat->mac_interface) {
>>>> +    case PHY_INTERFACE_MODE_MII:
>>>> +        break;
>>>
>>> dwmac->enable_eth_ck does not apply to MII mode ? Why ?
>>
>> It is like MP1 and MP13, nothing to set in syscfg register for case 
>> MII mode wo crystal.
>
> Have a look at STM32MP15xx RM0436 Figure 83. Peripheral clock 
> distribution for Ethernet.
>
> If RCC (top-left corner of the figure) generates 25 MHz MII clock 
> (yellow line) on eth_clk_fb (top-right corner), can I set 
> ETH_REF_CLK_SEL to position '1' and ETH_SEL[2] to '0' and feed ETH 
> (right side) clk_rx_i input with 25 MHz clock that way ?
>
> I seems like this should be possible, at least theoretically. Can you 
> check with the hardware/silicon people ?
No it is not possible (it will work if speed (and frequency) is fixed  
25Mhz=100Mbps, but for speed 10Mbps (2,5MHz) it will not work. (you can 
see than diviser are only for RMII mode)
>
> As a result, the MII/RMII mode would behave in a very similar way, and 
> so would GMII/RGMII mode behave in a very similar way. Effectively you 
> would end up with this (notice the fallthrough statements):
>
> +    case PHY_INTERFACE_MODE_RMII:
> +        val = SYSCFG_ETHCR_ETH_SEL_RMII;
> +        fallthrough;
> +    case PHY_INTERFACE_MODE_MII:
> +        if (dwmac->enable_eth_ck)
> +            val |= SYSCFG_ETHCR_ETH_REF_CLK_SEL;
> +        break;
> +
> +    case PHY_INTERFACE_MODE_RGMII:
> +    case PHY_INTERFACE_MODE_RGMII_ID:
> +    case PHY_INTERFACE_MODE_RGMII_RXID:
> +    case PHY_INTERFACE_MODE_RGMII_TXID:
> +        val = SYSCFG_ETHCR_ETH_SEL_RGMII;
> +        fallthrough;
> +    case PHY_INTERFACE_MODE_GMII:
> +        if (dwmac->enable_eth_ck)
> +            val |= SYSCFG_ETHCR_ETH_CLK_SEL;
> +        break;
>
> [...]
Marek Vasut June 18, 2024, 3 p.m. UTC | #5
On 6/18/24 11:09 AM, Christophe ROULLIER wrote:

Hi,

>>>>> +static int stm32mp2_configure_syscfg(struct plat_stmmacenet_data 
>>>>> *plat_dat)
>>>>> +{
>>>>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>>>>> +    u32 reg = dwmac->mode_reg;
>>>>> +    int val = 0;
>>>>> +
>>>>> +    switch (plat_dat->mac_interface) {
>>>>> +    case PHY_INTERFACE_MODE_MII:
>>>>> +        break;
>>>>
>>>> dwmac->enable_eth_ck does not apply to MII mode ? Why ?
>>>
>>> It is like MP1 and MP13, nothing to set in syscfg register for case 
>>> MII mode wo crystal.
>>
>> Have a look at STM32MP15xx RM0436 Figure 83. Peripheral clock 
>> distribution for Ethernet.
>>
>> If RCC (top-left corner of the figure) generates 25 MHz MII clock 
>> (yellow line) on eth_clk_fb (top-right corner), can I set 
>> ETH_REF_CLK_SEL to position '1' and ETH_SEL[2] to '0' and feed ETH 
>> (right side) clk_rx_i input with 25 MHz clock that way ?
>>
>> I seems like this should be possible, at least theoretically. Can you 
>> check with the hardware/silicon people ?
> No it is not possible (it will work if speed (and frequency) is fixed 
> 25Mhz=100Mbps, but for speed 10Mbps (2,5MHz) it will not work.

Could the pll4_p_ck or pll3_q_ck generate either 25 MHz or 2.5 MHz as 
needed in that case ? Then it would work, right ?

> (you can 
> see than diviser are only for RMII mode)

Do you refer to /2 and /20 dividers to the left of mac_speed_o[0] ?
Christophe Roullier June 19, 2024, 7:41 a.m. UTC | #6
Hi Marek,

On 6/18/24 17:00, Marek Vasut wrote:
> On 6/18/24 11:09 AM, Christophe ROULLIER wrote:
>
> Hi,
>
>>>>>> +static int stm32mp2_configure_syscfg(struct plat_stmmacenet_data 
>>>>>> *plat_dat)
>>>>>> +{
>>>>>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>>>>>> +    u32 reg = dwmac->mode_reg;
>>>>>> +    int val = 0;
>>>>>> +
>>>>>> +    switch (plat_dat->mac_interface) {
>>>>>> +    case PHY_INTERFACE_MODE_MII:
>>>>>> +        break;
>>>>>
>>>>> dwmac->enable_eth_ck does not apply to MII mode ? Why ?
>>>>
>>>> It is like MP1 and MP13, nothing to set in syscfg register for case 
>>>> MII mode wo crystal.
>>>
>>> Have a look at STM32MP15xx RM0436 Figure 83. Peripheral clock 
>>> distribution for Ethernet.
>>>
>>> If RCC (top-left corner of the figure) generates 25 MHz MII clock 
>>> (yellow line) on eth_clk_fb (top-right corner), can I set 
>>> ETH_REF_CLK_SEL to position '1' and ETH_SEL[2] to '0' and feed ETH 
>>> (right side) clk_rx_i input with 25 MHz clock that way ?
>>>
>>> I seems like this should be possible, at least theoretically. Can 
>>> you check with the hardware/silicon people ?
>> No it is not possible (it will work if speed (and frequency) is fixed 
>> 25Mhz=100Mbps, but for speed 10Mbps (2,5MHz) it will not work.
>
> Could the pll4_p_ck or pll3_q_ck generate either 25 MHz or 2.5 MHz as 
> needed in that case ? Then it would work, right ?

Yes you can set frequency you want for pll4 or pll3, if you set 25MHz 
and auto-negotiation of speed is 100Mbps it should work (pad ETH_CK of 
25MHz clock the PHY and eth_clk_fb set to 25MHz for clk_RX)

but if autoneg of speed is 10Mbps, then 2.5MHz is needed for clk_RX (you 
will provide 25Mhz). For RMII case, frequency from pll (eth_clk_fb) is 
automatically adjust in function of speed value, thanks to diviser /2, 
/20 with mac_speed_o.

>
>> (you can see than diviser are only for RMII mode)
>
> Do you refer to /2 and /20 dividers to the left of mac_speed_o[0] ?
Marek Vasut June 19, 2024, 1:14 p.m. UTC | #7
On 6/19/24 9:41 AM, Christophe ROULLIER wrote:

Hi,

>>>>>>> +static int stm32mp2_configure_syscfg(struct plat_stmmacenet_data 
>>>>>>> *plat_dat)
>>>>>>> +{
>>>>>>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>>>>>>> +    u32 reg = dwmac->mode_reg;
>>>>>>> +    int val = 0;
>>>>>>> +
>>>>>>> +    switch (plat_dat->mac_interface) {
>>>>>>> +    case PHY_INTERFACE_MODE_MII:
>>>>>>> +        break;
>>>>>>
>>>>>> dwmac->enable_eth_ck does not apply to MII mode ? Why ?
>>>>>
>>>>> It is like MP1 and MP13, nothing to set in syscfg register for case 
>>>>> MII mode wo crystal.
>>>>
>>>> Have a look at STM32MP15xx RM0436 Figure 83. Peripheral clock 
>>>> distribution for Ethernet.
>>>>
>>>> If RCC (top-left corner of the figure) generates 25 MHz MII clock 
>>>> (yellow line) on eth_clk_fb (top-right corner), can I set 
>>>> ETH_REF_CLK_SEL to position '1' and ETH_SEL[2] to '0' and feed ETH 
>>>> (right side) clk_rx_i input with 25 MHz clock that way ?
>>>>
>>>> I seems like this should be possible, at least theoretically. Can 
>>>> you check with the hardware/silicon people ?
>>> No it is not possible (it will work if speed (and frequency) is fixed 
>>> 25Mhz=100Mbps, but for speed 10Mbps (2,5MHz) it will not work.
>>
>> Could the pll4_p_ck or pll3_q_ck generate either 25 MHz or 2.5 MHz as 
>> needed in that case ? Then it would work, right ?
> 
> Yes you can set frequency you want for pll4 or pll3, if you set 25MHz 
> and auto-negotiation of speed is 100Mbps it should work (pad ETH_CK of 
> 25MHz clock the PHY and eth_clk_fb set to 25MHz for clk_RX)
> 
> but if autoneg of speed is 10Mbps, then 2.5MHz is needed for clk_RX (you 
> will provide 25Mhz)

What if:

- Aneg is 10 Mbps
- PLL4_P_CK/PLL3_Q_CK = 2.5 MHz
- ETH_REF_CLK_SEL = 1
- ETH_SEL[2] = 0

?

Then, clk_rx_i is 2.5 MHz, right ?

Does this configuration work ?

> . For RMII case, frequency from pll (eth_clk_fb) is 
> automatically adjust in function of speed value, thanks to diviser /2, 
> /20 with mac_speed_o.
Christophe Roullier June 19, 2024, 3:40 p.m. UTC | #8
On 6/19/24 15:14, Marek Vasut wrote:
> On 6/19/24 9:41 AM, Christophe ROULLIER wrote:
>
> Hi,
>
>>>>>>>> +static int stm32mp2_configure_syscfg(struct 
>>>>>>>> plat_stmmacenet_data *plat_dat)
>>>>>>>> +{
>>>>>>>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>>>>>>>> +    u32 reg = dwmac->mode_reg;
>>>>>>>> +    int val = 0;
>>>>>>>> +
>>>>>>>> +    switch (plat_dat->mac_interface) {
>>>>>>>> +    case PHY_INTERFACE_MODE_MII:
>>>>>>>> +        break;
>>>>>>>
>>>>>>> dwmac->enable_eth_ck does not apply to MII mode ? Why ?
>>>>>>
>>>>>> It is like MP1 and MP13, nothing to set in syscfg register for 
>>>>>> case MII mode wo crystal.
>>>>>
>>>>> Have a look at STM32MP15xx RM0436 Figure 83. Peripheral clock 
>>>>> distribution for Ethernet.
>>>>>
>>>>> If RCC (top-left corner of the figure) generates 25 MHz MII clock 
>>>>> (yellow line) on eth_clk_fb (top-right corner), can I set 
>>>>> ETH_REF_CLK_SEL to position '1' and ETH_SEL[2] to '0' and feed ETH 
>>>>> (right side) clk_rx_i input with 25 MHz clock that way ?
>>>>>
>>>>> I seems like this should be possible, at least theoretically. Can 
>>>>> you check with the hardware/silicon people ?
>>>> No it is not possible (it will work if speed (and frequency) is 
>>>> fixed 25Mhz=100Mbps, but for speed 10Mbps (2,5MHz) it will not work.
>>>
>>> Could the pll4_p_ck or pll3_q_ck generate either 25 MHz or 2.5 MHz 
>>> as needed in that case ? Then it would work, right ?
>>
>> Yes you can set frequency you want for pll4 or pll3, if you set 25MHz 
>> and auto-negotiation of speed is 100Mbps it should work (pad ETH_CK 
>> of 25MHz clock the PHY and eth_clk_fb set to 25MHz for clk_RX)
>>
>> but if autoneg of speed is 10Mbps, then 2.5MHz is needed for clk_RX 
>> (you will provide 25Mhz)
>
> What if:
>
> - Aneg is 10 Mbps
> - PLL4_P_CK/PLL3_Q_CK = 2.5 MHz
> - ETH_REF_CLK_SEL = 1
> - ETH_SEL[2] = 0
>
> ?
>
> Then, clk_rx_i is 2.5 MHz, right ?
Yes that right
>
> Does this configuration work ?
For me no, because PHY Ethernet Oscillator/cristal need in PAD 25Mhz or 
50Mhz, I think it is does not work if oscillator frequency provided is 
2.5MHz (To my knowledge there is no Ethernet PHY which have oscillator 
working to 2.5MHz)
>
>> . For RMII case, frequency from pll (eth_clk_fb) is automatically 
>> adjust in function of speed value, thanks to diviser /2, /20 with 
>> mac_speed_o.
Marek Vasut June 19, 2024, 6:56 p.m. UTC | #9
On 6/19/24 5:40 PM, Christophe ROULLIER wrote:
> 
> On 6/19/24 15:14, Marek Vasut wrote:
>> On 6/19/24 9:41 AM, Christophe ROULLIER wrote:
>>
>> Hi,
>>
>>>>>>>>> +static int stm32mp2_configure_syscfg(struct 
>>>>>>>>> plat_stmmacenet_data *plat_dat)
>>>>>>>>> +{
>>>>>>>>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>>>>>>>>> +    u32 reg = dwmac->mode_reg;
>>>>>>>>> +    int val = 0;
>>>>>>>>> +
>>>>>>>>> +    switch (plat_dat->mac_interface) {
>>>>>>>>> +    case PHY_INTERFACE_MODE_MII:
>>>>>>>>> +        break;
>>>>>>>>
>>>>>>>> dwmac->enable_eth_ck does not apply to MII mode ? Why ?
>>>>>>>
>>>>>>> It is like MP1 and MP13, nothing to set in syscfg register for 
>>>>>>> case MII mode wo crystal.
>>>>>>
>>>>>> Have a look at STM32MP15xx RM0436 Figure 83. Peripheral clock 
>>>>>> distribution for Ethernet.
>>>>>>
>>>>>> If RCC (top-left corner of the figure) generates 25 MHz MII clock 
>>>>>> (yellow line) on eth_clk_fb (top-right corner), can I set 
>>>>>> ETH_REF_CLK_SEL to position '1' and ETH_SEL[2] to '0' and feed ETH 
>>>>>> (right side) clk_rx_i input with 25 MHz clock that way ?
>>>>>>
>>>>>> I seems like this should be possible, at least theoretically. Can 
>>>>>> you check with the hardware/silicon people ?
>>>>> No it is not possible (it will work if speed (and frequency) is 
>>>>> fixed 25Mhz=100Mbps, but for speed 10Mbps (2,5MHz) it will not work.
>>>>
>>>> Could the pll4_p_ck or pll3_q_ck generate either 25 MHz or 2.5 MHz 
>>>> as needed in that case ? Then it would work, right ?
>>>
>>> Yes you can set frequency you want for pll4 or pll3, if you set 25MHz 
>>> and auto-negotiation of speed is 100Mbps it should work (pad ETH_CK 
>>> of 25MHz clock the PHY and eth_clk_fb set to 25MHz for clk_RX)
>>>
>>> but if autoneg of speed is 10Mbps, then 2.5MHz is needed for clk_RX 
>>> (you will provide 25Mhz)
>>
>> What if:
>>
>> - Aneg is 10 Mbps
>> - PLL4_P_CK/PLL3_Q_CK = 2.5 MHz
>> - ETH_REF_CLK_SEL = 1
>> - ETH_SEL[2] = 0
>>
>> ?
>>
>> Then, clk_rx_i is 2.5 MHz, right ?
> Yes that right
>>
>> Does this configuration work ?
> For me no, because PHY Ethernet Oscillator/cristal need in PAD 25Mhz or 
> 50Mhz, I think it is does not work if oscillator frequency provided is 
> 2.5MHz (To my knowledge there is no Ethernet PHY which have oscillator 
> working to 2.5MHz)

Would it work if the PHY had a dedicated Xtal , while the clocking of 
the MAC was done using RCC ?
diff mbox series

Patch

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index b2db0e26c4e4..49685fc9c7ee 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -53,7 +53,18 @@ 
 #define SYSCFG_MCU_ETH_SEL_MII		0
 #define SYSCFG_MCU_ETH_SEL_RMII		1
 
-/* STM32MP1 register definitions
+/* STM32MP2 register definitions */
+#define SYSCFG_MP2_ETH_MASK		GENMASK(31, 0)
+
+#define SYSCFG_ETHCR_ETH_PTP_CLK_SEL	BIT(2)
+#define SYSCFG_ETHCR_ETH_CLK_SEL	BIT(1)
+#define SYSCFG_ETHCR_ETH_REF_CLK_SEL	BIT(0)
+
+#define SYSCFG_ETHCR_ETH_SEL_MII	0
+#define SYSCFG_ETHCR_ETH_SEL_RGMII	BIT(4)
+#define SYSCFG_ETHCR_ETH_SEL_RMII	BIT(6)
+
+/* STM32MPx register definitions
  *
  * Below table summarizes the clock requirement and clock sources for
  * supported phy interface modes.
@@ -277,6 +288,49 @@  static int stm32mp1_configure_pmcr(struct plat_stmmacenet_data *plat_dat)
 				 dwmac->mode_mask, val);
 }
 
+static int stm32mp2_configure_syscfg(struct plat_stmmacenet_data *plat_dat)
+{
+	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
+	u32 reg = dwmac->mode_reg;
+	int val = 0;
+
+	switch (plat_dat->mac_interface) {
+	case PHY_INTERFACE_MODE_MII:
+		break;
+	case PHY_INTERFACE_MODE_GMII:
+		if (dwmac->enable_eth_ck)
+			val |= SYSCFG_ETHCR_ETH_CLK_SEL;
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		val = SYSCFG_ETHCR_ETH_SEL_RMII;
+		if (dwmac->enable_eth_ck)
+			val |= SYSCFG_ETHCR_ETH_REF_CLK_SEL;
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		val = SYSCFG_ETHCR_ETH_SEL_RGMII;
+		if (dwmac->enable_eth_ck)
+			val |= SYSCFG_ETHCR_ETH_CLK_SEL;
+		break;
+	default:
+		dev_err(dwmac->dev, "Mode %s not supported",
+			phy_modes(plat_dat->mac_interface));
+		/* Do not manage others interfaces */
+		return -EINVAL;
+	}
+
+	dev_dbg(dwmac->dev, "Mode %s", phy_modes(plat_dat->mac_interface));
+
+	/*  select PTP (IEEE1588) clock selection from RCC (ck_ker_ethxptp) */
+	val |= SYSCFG_ETHCR_ETH_PTP_CLK_SEL;
+
+	/* Update ETHCR (set register) */
+	return regmap_update_bits(dwmac->regmap, reg,
+				 SYSCFG_MP2_ETH_MASK, val);
+}
+
 static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 {
 	int ret;
@@ -292,6 +346,21 @@  static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 	return stm32mp1_configure_pmcr(plat_dat);
 }
 
+static int stm32mp2_set_mode(struct plat_stmmacenet_data *plat_dat)
+{
+	int ret;
+
+	ret = stm32mp1_select_ethck_external(plat_dat);
+	if (ret)
+		return ret;
+
+	ret = stm32mp1_validate_ethck_rate(plat_dat);
+	if (ret)
+		return ret;
+
+	return stm32mp2_configure_syscfg(plat_dat);
+}
+
 static int stm32mcu_set_mode(struct plat_stmmacenet_data *plat_dat)
 {
 	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
@@ -348,12 +417,6 @@  static int stm32_dwmac_parse_data(struct stm32_dwmac *dwmac,
 		return PTR_ERR(dwmac->clk_rx);
 	}
 
-	if (dwmac->ops->parse_data) {
-		err = dwmac->ops->parse_data(dwmac, dev);
-		if (err)
-			return err;
-	}
-
 	/* Get mode register */
 	dwmac->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscon");
 	if (IS_ERR(dwmac->regmap))
@@ -365,20 +428,14 @@  static int stm32_dwmac_parse_data(struct stm32_dwmac *dwmac,
 		return err;
 	}
 
-	dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
-	err = of_property_read_u32_index(np, "st,syscon", 2, &dwmac->mode_mask);
-	if (err) {
-		if (dwmac->ops->is_mp13)
-			dev_err(dev, "Sysconfig register mask must be set (%d)\n", err);
-		else
-			dev_dbg(dev, "Warning sysconfig register mask not set\n");
-	}
+	if (dwmac->ops->parse_data)
+		err = dwmac->ops->parse_data(dwmac, dev);
 
 	return err;
 }
 
-static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
-			       struct device *dev)
+static int stm32mpx_common_parse_data(struct stm32_dwmac *dwmac,
+				      struct device *dev)
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct device_node *np = dev->of_node;
@@ -439,6 +496,27 @@  static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
 	return err;
 }
 
+static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
+			       struct device *dev)
+{
+	struct device_node *np = dev->of_node;
+	int err = 0;
+
+	if (stm32mpx_common_parse_data(dwmac, dev))
+		return err;
+
+	dwmac->mode_mask = SYSCFG_MP1_ETH_MASK;
+	err = of_property_read_u32_index(np, "st,syscon", 2, &dwmac->mode_mask);
+	if (err) {
+		if (dwmac->ops->is_mp13)
+			dev_err(dev, "Sysconfig register mask must be set (%d)\n", err);
+		else
+			dev_dbg(dev, "Warning sysconfig register mask not set\n");
+	}
+
+	return err;
+}
+
 static int stm32_dwmac_probe(struct platform_device *pdev)
 {
 	struct plat_stmmacenet_data *plat_dat;
@@ -586,10 +664,19 @@  static struct stm32_ops stm32mp13_dwmac_data = {
 	.clk_rx_enable_in_suspend = true
 };
 
+static struct stm32_ops stm32mp25_dwmac_data = {
+	.set_mode = stm32mp2_set_mode,
+	.suspend = stm32mp1_suspend,
+	.resume = stm32mp1_resume,
+	.parse_data = stm32mpx_common_parse_data,
+	.clk_rx_enable_in_suspend = true
+};
+
 static const struct of_device_id stm32_dwmac_match[] = {
 	{ .compatible = "st,stm32-dwmac", .data = &stm32mcu_dwmac_data},
 	{ .compatible = "st,stm32mp1-dwmac", .data = &stm32mp1_dwmac_data},
 	{ .compatible = "st,stm32mp13-dwmac", .data = &stm32mp13_dwmac_data},
+	{ .compatible = "st,stm32mp25-dwmac", .data = &stm32mp25_dwmac_data},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, stm32_dwmac_match);