| Message ID | 20240613093706.480700-1-j-choudhary@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2] arm64: dts: ti: k3-j721e: Add overlay for J721E Infotainment Expansion Board | expand |
Adding Tomi in the loop. On 13-Jun-24 15:07, Jayesh Choudhary wrote: > From: Tomi Valkeinen <tomi.valkeinen@ti.com> > > J721E common processor board can be interfaced with the infotainment > expansion board[0] to enable the following audio/video interfaces in > addition to the peripherals provided by the common processor board: > - Two Audio codecs each with three Stereo Inputs and four Stereo Outputs > - Audio input over FPD Link III > - Digital Audio Interface TX/RX > - HDMI/FPD LINK III Display out > - LI/OV Camera input > > Add support for TFP410 HDMI bridge located on the Infotainment Expansion > Board (connected to J46 & J51). > Add a HDMI connector node and connect the endpoints as below: > DSS => TFP410 bridge => HDMI connector > Also add the pinmux data and board muxes for DPI. > > Rest of the peripherals are not added as of now. > > [0]: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf> > > Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> > [j-choudhary@ti.com: minor cleanup] > Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com> > --- > > Testlog: > <https://gist.github.com/Jayesh2000/45f75cf075cc969d1dfc9015c6f23fd4> > > Changelog v1->v2: > - rebased on next-20240613 > - add dtbo in ascending order in Makefile > - Mention in commit message that other peripherals on the expansion board > are not added as of now. > > v1 patch: > <https://lore.kernel.org/all/20240227120310.661579-1-j-choudhary@ti.com/> > > arch/arm64/boot/dts/ti/Makefile | 4 + > ...-j721e-common-proc-board-infotainment.dtso | 164 ++++++++++++++++++ > 2 files changed, 168 insertions(+) > create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso > > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile > index d956372a7163..5c6701897f31 100644 > --- a/arch/arm64/boot/dts/ti/Makefile > +++ b/arch/arm64/boot/dts/ti/Makefile > @@ -83,6 +83,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-evm.dtb > # Boards with J721e SoC > k3-j721e-evm-dtbs := k3-j721e-common-proc-board.dtb k3-j721e-evm-quad-port-eth-exp.dtbo > dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb > +dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board-infotainment.dtbo > dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm.dtb > dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-gesi-exp-board.dtbo > dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-pcie0-ep.dtbo > @@ -151,6 +152,8 @@ k3-am68-sk-base-board-csi2-dual-imx219-dtbs := k3-am68-sk-base-board.dtb \ > k3-j721e-sk-csi2-dual-imx219.dtbo > k3-am69-sk-csi2-dual-imx219-dtbs := k3-am69-sk.dtb \ > k3-j721e-sk-csi2-dual-imx219.dtbo > +k3-j721e-common-proc-board-infotainment-dtbs := k3-j721e-common-proc-board.dtb \ > + k3-j721e-common-proc-board-infotainment.dtbo > k3-j721e-evm-pcie0-ep-dtbs := k3-j721e-common-proc-board.dtb \ > k3-j721e-evm-pcie0-ep.dtbo > k3-j721e-sk-csi2-dual-imx219-dtbs := k3-j721e-sk.dtb \ > @@ -182,6 +185,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \ > k3-am642-tqma64xxl-mbax4xxl-wlan.dtb \ > k3-am68-sk-base-board-csi2-dual-imx219.dtb \ > k3-am69-sk-csi2-dual-imx219.dtb \ > + k3-j721e-common-proc-board-infotainment.dtb \ > k3-j721e-evm-pcie0-ep.dtb \ > k3-j721e-sk-csi2-dual-imx219.dtb \ > k3-j721s2-evm-pcie1-ep.dtb \ > diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso > new file mode 100644 > index 000000000000..65a7e54f0884 > --- /dev/null > +++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso > @@ -0,0 +1,164 @@ > +// SPDX-License-Identifier: GPL-2.0-only OR MIT> +/* > + * Infotainment Expansion Board for j721e-evm > + * User Guide: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf> > + * > + * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/ > + */ > + > +/dts-v1/; > +/plugin/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/irq.h> > + > +#include "k3-pinctrl.h" > + > +&{/} { > + hdmi-connector { > + compatible = "hdmi-connector"; > + label = "hdmi"; > + type = "a"; > + ddc-i2c-bus = <&main_i2c1>; > + digital; > + /* P12 - HDMI_HPD */ > + hpd-gpios = <&exp6 10 GPIO_ACTIVE_HIGH>; > + > + port { > + hdmi_connector_in: endpoint { > + remote-endpoint = <&tfp410_out>; > + }; > + }; > + }; > + > + dvi-bridge { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "ti,tfp410"; > + /* P10 - HDMI_PDn */ > + powerdown-gpios = <&exp6 8 GPIO_ACTIVE_LOW>; > + > + port@0 { > + reg = <0>; > + > + tfp410_in: endpoint { > + remote-endpoint = <&dpi_out0>; > + pclk-sample = <1>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + tfp410_out: endpoint { > + remote-endpoint = > + <&hdmi_connector_in>; > + }; > + }; > + }; > +}; > + > +&main_pmx0 { > + main_i2c1_exp6_pins_default: main-i2c1-exp6-default-pins { > + pinctrl-single,pins = < > + J721E_IOPAD(0x264, PIN_INPUT, 7) /* (T29) MMC2_DAT2.GPIO1_24 */ > + >; > + }; > + > + dss_vout0_pins_default: dss-vout0-default-pins { > + pinctrl-single,pins = < > + J721E_IOPAD(0x58, PIN_OUTPUT, 10) /* (AE22) PRG1_PRU1_GPO0.VOUT0_DATA0 */ > + J721E_IOPAD(0x5c, PIN_OUTPUT, 10) /* (AG23) PRG1_PRU1_GPO1.VOUT0_DATA1 */ > + J721E_IOPAD(0x60, PIN_OUTPUT, 10) /* (AF23) PRG1_PRU1_GPO2.VOUT0_DATA2 */ > + J721E_IOPAD(0x64, PIN_OUTPUT, 10) /* (AD23) PRG1_PRU1_GPO3.VOUT0_DATA3 */ > + J721E_IOPAD(0x68, PIN_OUTPUT, 10) /* (AH24) PRG1_PRU1_GPO4.VOUT0_DATA4 */ > + J721E_IOPAD(0x6c, PIN_OUTPUT, 10) /* (AG21) PRG1_PRU1_GPO5.VOUT0_DATA5 */ > + J721E_IOPAD(0x70, PIN_OUTPUT, 10) /* (AE23) PRG1_PRU1_GPO6.VOUT0_DATA6 */ > + J721E_IOPAD(0x74, PIN_OUTPUT, 10) /* (AC21) PRG1_PRU1_GPO7.VOUT0_DATA7 */ > + J721E_IOPAD(0x78, PIN_OUTPUT, 10) /* (Y23) PRG1_PRU1_GPO8.VOUT0_DATA8 */ > + J721E_IOPAD(0x7c, PIN_OUTPUT, 10) /* (AF21) PRG1_PRU1_GPO9.VOUT0_DATA9 */ > + J721E_IOPAD(0x80, PIN_OUTPUT, 10) /* (AB23) PRG1_PRU1_GPO10.VOUT0_DATA10 */ > + J721E_IOPAD(0x84, PIN_OUTPUT, 10) /* (AJ25) PRG1_PRU1_GPO11.VOUT0_DATA11 */ > + J721E_IOPAD(0x88, PIN_OUTPUT, 10) /* (AH25) PRG1_PRU1_GPO12.VOUT0_DATA12 */ > + J721E_IOPAD(0x8c, PIN_OUTPUT, 10) /* (AG25) PRG1_PRU1_GPO13.VOUT0_DATA13 */ > + J721E_IOPAD(0x90, PIN_OUTPUT, 10) /* (AH26) PRG1_PRU1_GPO14.VOUT0_DATA14 */ > + J721E_IOPAD(0x94, PIN_OUTPUT, 10) /* (AJ27) PRG1_PRU1_GPO15.VOUT0_DATA15 */ > + J721E_IOPAD(0x30, PIN_OUTPUT, 10) /* (AF24) PRG1_PRU0_GPO11.VOUT0_DATA16 */ > + J721E_IOPAD(0x34, PIN_OUTPUT, 10) /* (AJ24) PRG1_PRU0_GPO12.VOUT0_DATA17 */ > + J721E_IOPAD(0x38, PIN_OUTPUT, 10) /* (AG24) PRG1_PRU0_GPO13.VOUT0_DATA18 */ > + J721E_IOPAD(0x3c, PIN_OUTPUT, 10) /* (AD24) PRG1_PRU0_GPO14.VOUT0_DATA19 */ > + J721E_IOPAD(0x40, PIN_OUTPUT, 10) /* (AC24) PRG1_PRU0_GPO15.VOUT0_DATA20 */ > + J721E_IOPAD(0x44, PIN_OUTPUT, 10) /* (AE24) PRG1_PRU0_GPO16.VOUT0_DATA21 */ > + J721E_IOPAD(0x24, PIN_OUTPUT, 10) /* (AJ20) PRG1_PRU0_GPO8.VOUT0_DATA22 */ > + J721E_IOPAD(0x28, PIN_OUTPUT, 10) /* (AG20) PRG1_PRU0_GPO9.VOUT0_DATA23 */ > + J721E_IOPAD(0x9c, PIN_OUTPUT, 10) /* (AC22) PRG1_PRU1_GPO17.VOUT0_DE */ > + J721E_IOPAD(0x98, PIN_OUTPUT, 10) /* (AJ26) PRG1_PRU1_GPO16.VOUT0_HSYNC */ > + J721E_IOPAD(0xa4, PIN_OUTPUT, 10) /* (AH22) PRG1_PRU1_GPO19.VOUT0_PCLK */ > + J721E_IOPAD(0xa0, PIN_OUTPUT, 10) /* (AJ22) PRG1_PRU1_GPO18.VOUT0_VSYNC */ > + >; > + }; > +}; > + > +&exp1 { > + p14-hog { > + /* P14 - VINOUT_MUX_SEL0 */ > + gpio-hog; > + gpios = <12 GPIO_ACTIVE_HIGH>; > + output-low; > + line-name = "VINOUT_MUX_SEL0"; > + }; > + > + p15-hog { > + /* P15 - VINOUT_MUX_SEL1 */ > + gpio-hog; > + gpios = <13 GPIO_ACTIVE_HIGH>; > + output-high; > + line-name = "VINOUT_MUX_SEL1"; > + }; > +}; > + > +&main_i2c1 { > + /* i2c1 is used for DVI DDC, so we need to use 100kHz */ > + clock-frequency = <100000>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + exp6: gpio@21 { > + compatible = "ti,tca6416"; > + reg = <0x21>; > + gpio-controller; > + #gpio-cells = <2>; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_i2c1_exp6_pins_default>; > + interrupt-parent = <&main_gpio1>; > + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; > + interrupt-controller; > + #interrupt-cells = <2>; > + > + p11-hog { > + /* P11 - HDMI_DDC_OE */ > + gpio-hog; > + gpios = <9 GPIO_ACTIVE_HIGH>; > + output-high; > + line-name = "HDMI_DDC_OE"; > + }; > + }; > +}; > + > +&dss { > + pinctrl-names = "default"; > + pinctrl-0 = <&dss_vout0_pins_default>; > +}; > + > +&dss_ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@1 { > + reg = <1>; > + > + dpi_out0: endpoint { > + remote-endpoint = <&tfp410_in>; > + }; > + }; > +}; Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Hi Jayesh Choudhary, On Thu, 13 Jun 2024 15:07:06 +0530, Jayesh Choudhary wrote: > J721E common processor board can be interfaced with the infotainment > expansion board[0] to enable the following audio/video interfaces in > addition to the peripherals provided by the common processor board: > - Two Audio codecs each with three Stereo Inputs and four Stereo Outputs > - Audio input over FPD Link III > - Digital Audio Interface TX/RX > - HDMI/FPD LINK III Display out > - LI/OV Camera input > > [...] I have applied the following to branch ti-k3-dts-next on [1]. Thank you! [1/1] arm64: dts: ti: k3-j721e: Add overlay for J721E Infotainment Expansion Board commit: 9c0fa304fa561abfe83d328ffc4f638c0152bead All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted. You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed. If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced. Please add any relevant lists and maintainers to the CCs when replying to this mail. [1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git -- Vignesh
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index d956372a7163..5c6701897f31 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -83,6 +83,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-evm.dtb # Boards with J721e SoC k3-j721e-evm-dtbs := k3-j721e-common-proc-board.dtb k3-j721e-evm-quad-port-eth-exp.dtbo dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb +dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board-infotainment.dtbo dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm.dtb dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-gesi-exp-board.dtbo dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-pcie0-ep.dtbo @@ -151,6 +152,8 @@ k3-am68-sk-base-board-csi2-dual-imx219-dtbs := k3-am68-sk-base-board.dtb \ k3-j721e-sk-csi2-dual-imx219.dtbo k3-am69-sk-csi2-dual-imx219-dtbs := k3-am69-sk.dtb \ k3-j721e-sk-csi2-dual-imx219.dtbo +k3-j721e-common-proc-board-infotainment-dtbs := k3-j721e-common-proc-board.dtb \ + k3-j721e-common-proc-board-infotainment.dtbo k3-j721e-evm-pcie0-ep-dtbs := k3-j721e-common-proc-board.dtb \ k3-j721e-evm-pcie0-ep.dtbo k3-j721e-sk-csi2-dual-imx219-dtbs := k3-j721e-sk.dtb \ @@ -182,6 +185,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \ k3-am642-tqma64xxl-mbax4xxl-wlan.dtb \ k3-am68-sk-base-board-csi2-dual-imx219.dtb \ k3-am69-sk-csi2-dual-imx219.dtb \ + k3-j721e-common-proc-board-infotainment.dtb \ k3-j721e-evm-pcie0-ep.dtb \ k3-j721e-sk-csi2-dual-imx219.dtb \ k3-j721s2-evm-pcie1-ep.dtb \ diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso new file mode 100644 index 000000000000..65a7e54f0884 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board-infotainment.dtso @@ -0,0 +1,164 @@ +// SPDX-License-Identifier: GPL-2.0-only OR MIT +/* + * Infotainment Expansion Board for j721e-evm + * User Guide: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf> + * + * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#include "k3-pinctrl.h" + +&{/} { + hdmi-connector { + compatible = "hdmi-connector"; + label = "hdmi"; + type = "a"; + ddc-i2c-bus = <&main_i2c1>; + digital; + /* P12 - HDMI_HPD */ + hpd-gpios = <&exp6 10 GPIO_ACTIVE_HIGH>; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tfp410_out>; + }; + }; + }; + + dvi-bridge { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,tfp410"; + /* P10 - HDMI_PDn */ + powerdown-gpios = <&exp6 8 GPIO_ACTIVE_LOW>; + + port@0 { + reg = <0>; + + tfp410_in: endpoint { + remote-endpoint = <&dpi_out0>; + pclk-sample = <1>; + }; + }; + + port@1 { + reg = <1>; + + tfp410_out: endpoint { + remote-endpoint = + <&hdmi_connector_in>; + }; + }; + }; +}; + +&main_pmx0 { + main_i2c1_exp6_pins_default: main-i2c1-exp6-default-pins { + pinctrl-single,pins = < + J721E_IOPAD(0x264, PIN_INPUT, 7) /* (T29) MMC2_DAT2.GPIO1_24 */ + >; + }; + + dss_vout0_pins_default: dss-vout0-default-pins { + pinctrl-single,pins = < + J721E_IOPAD(0x58, PIN_OUTPUT, 10) /* (AE22) PRG1_PRU1_GPO0.VOUT0_DATA0 */ + J721E_IOPAD(0x5c, PIN_OUTPUT, 10) /* (AG23) PRG1_PRU1_GPO1.VOUT0_DATA1 */ + J721E_IOPAD(0x60, PIN_OUTPUT, 10) /* (AF23) PRG1_PRU1_GPO2.VOUT0_DATA2 */ + J721E_IOPAD(0x64, PIN_OUTPUT, 10) /* (AD23) PRG1_PRU1_GPO3.VOUT0_DATA3 */ + J721E_IOPAD(0x68, PIN_OUTPUT, 10) /* (AH24) PRG1_PRU1_GPO4.VOUT0_DATA4 */ + J721E_IOPAD(0x6c, PIN_OUTPUT, 10) /* (AG21) PRG1_PRU1_GPO5.VOUT0_DATA5 */ + J721E_IOPAD(0x70, PIN_OUTPUT, 10) /* (AE23) PRG1_PRU1_GPO6.VOUT0_DATA6 */ + J721E_IOPAD(0x74, PIN_OUTPUT, 10) /* (AC21) PRG1_PRU1_GPO7.VOUT0_DATA7 */ + J721E_IOPAD(0x78, PIN_OUTPUT, 10) /* (Y23) PRG1_PRU1_GPO8.VOUT0_DATA8 */ + J721E_IOPAD(0x7c, PIN_OUTPUT, 10) /* (AF21) PRG1_PRU1_GPO9.VOUT0_DATA9 */ + J721E_IOPAD(0x80, PIN_OUTPUT, 10) /* (AB23) PRG1_PRU1_GPO10.VOUT0_DATA10 */ + J721E_IOPAD(0x84, PIN_OUTPUT, 10) /* (AJ25) PRG1_PRU1_GPO11.VOUT0_DATA11 */ + J721E_IOPAD(0x88, PIN_OUTPUT, 10) /* (AH25) PRG1_PRU1_GPO12.VOUT0_DATA12 */ + J721E_IOPAD(0x8c, PIN_OUTPUT, 10) /* (AG25) PRG1_PRU1_GPO13.VOUT0_DATA13 */ + J721E_IOPAD(0x90, PIN_OUTPUT, 10) /* (AH26) PRG1_PRU1_GPO14.VOUT0_DATA14 */ + J721E_IOPAD(0x94, PIN_OUTPUT, 10) /* (AJ27) PRG1_PRU1_GPO15.VOUT0_DATA15 */ + J721E_IOPAD(0x30, PIN_OUTPUT, 10) /* (AF24) PRG1_PRU0_GPO11.VOUT0_DATA16 */ + J721E_IOPAD(0x34, PIN_OUTPUT, 10) /* (AJ24) PRG1_PRU0_GPO12.VOUT0_DATA17 */ + J721E_IOPAD(0x38, PIN_OUTPUT, 10) /* (AG24) PRG1_PRU0_GPO13.VOUT0_DATA18 */ + J721E_IOPAD(0x3c, PIN_OUTPUT, 10) /* (AD24) PRG1_PRU0_GPO14.VOUT0_DATA19 */ + J721E_IOPAD(0x40, PIN_OUTPUT, 10) /* (AC24) PRG1_PRU0_GPO15.VOUT0_DATA20 */ + J721E_IOPAD(0x44, PIN_OUTPUT, 10) /* (AE24) PRG1_PRU0_GPO16.VOUT0_DATA21 */ + J721E_IOPAD(0x24, PIN_OUTPUT, 10) /* (AJ20) PRG1_PRU0_GPO8.VOUT0_DATA22 */ + J721E_IOPAD(0x28, PIN_OUTPUT, 10) /* (AG20) PRG1_PRU0_GPO9.VOUT0_DATA23 */ + J721E_IOPAD(0x9c, PIN_OUTPUT, 10) /* (AC22) PRG1_PRU1_GPO17.VOUT0_DE */ + J721E_IOPAD(0x98, PIN_OUTPUT, 10) /* (AJ26) PRG1_PRU1_GPO16.VOUT0_HSYNC */ + J721E_IOPAD(0xa4, PIN_OUTPUT, 10) /* (AH22) PRG1_PRU1_GPO19.VOUT0_PCLK */ + J721E_IOPAD(0xa0, PIN_OUTPUT, 10) /* (AJ22) PRG1_PRU1_GPO18.VOUT0_VSYNC */ + >; + }; +}; + +&exp1 { + p14-hog { + /* P14 - VINOUT_MUX_SEL0 */ + gpio-hog; + gpios = <12 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "VINOUT_MUX_SEL0"; + }; + + p15-hog { + /* P15 - VINOUT_MUX_SEL1 */ + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "VINOUT_MUX_SEL1"; + }; +}; + +&main_i2c1 { + /* i2c1 is used for DVI DDC, so we need to use 100kHz */ + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + + exp6: gpio@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_exp6_pins_default>; + interrupt-parent = <&main_gpio1>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + + p11-hog { + /* P11 - HDMI_DDC_OE */ + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "HDMI_DDC_OE"; + }; + }; +}; + +&dss { + pinctrl-names = "default"; + pinctrl-0 = <&dss_vout0_pins_default>; +}; + +&dss_ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + dpi_out0: endpoint { + remote-endpoint = <&tfp410_in>; + }; + }; +};