diff mbox series

power: supply: core: return -EAGAIN on uninitialized read temp

Message ID 20240704-topic-sm8x50-upstream-fix-battmgr-temp-tz-warn-v1-1-9d66d6f6efde@linaro.org (mailing list archive)
State Not Applicable
Headers show
Series power: supply: core: return -EAGAIN on uninitialized read temp | expand

Commit Message

Neil Armstrong July 4, 2024, 8:52 a.m. UTC
If the thermal core tries to update the temperature from an
uninitialized power supply, it will swawn the following warning:
thermal thermal_zoneXX: failed to read out thermal zone (-19)

But reading from an uninitialized power supply should not be
considered as a fatal error, but the thermal core expects
the -EAGAIN error to be returned in this particular case.

So convert -ENODEV as -EAGAIN to express the fact that reading
temperature from an uninitialized power supply shouldn't be
a fatal error, but should indicate to the thermal zone it should
retry later.

It notably removes such messages on Qualcomm platforms using the
qcom_battmgr driver spawning warnings until the aDSP firmware
gets up and the battery manager reports valid data.

Link: https://lore.kernel.org/all/2ed4c630-204a-4f80-a37f-f2ca838eb455@linaro.org/
Fixes: 5bc28b93a36e ("power_supply: power_supply_read_temp only if use_cnt > 0")
Fixes: 3be330bf8860 ("power_supply: Register battery as a thermal zone")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/power/supply/power_supply_core.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)


---
base-commit: 82e4255305c554b0bb18b7ccf2db86041b4c8b6e
change-id: 20240704-topic-sm8x50-upstream-fix-battmgr-temp-tz-warn-077166861efb

Best regards,

Comments

Greg KH July 4, 2024, 9:12 a.m. UTC | #1
On Thu, Jul 04, 2024 at 10:52:08AM +0200, Neil Armstrong wrote:
> If the thermal core tries to update the temperature from an
> uninitialized power supply, it will swawn the following warning:
> thermal thermal_zoneXX: failed to read out thermal zone (-19)
> 
> But reading from an uninitialized power supply should not be
> considered as a fatal error, but the thermal core expects
> the -EAGAIN error to be returned in this particular case.
> 
> So convert -ENODEV as -EAGAIN to express the fact that reading
> temperature from an uninitialized power supply shouldn't be
> a fatal error, but should indicate to the thermal zone it should
> retry later.
> 
> It notably removes such messages on Qualcomm platforms using the
> qcom_battmgr driver spawning warnings until the aDSP firmware
> gets up and the battery manager reports valid data.
> 
> Link: https://lore.kernel.org/all/2ed4c630-204a-4f80-a37f-f2ca838eb455@linaro.org/
> Fixes: 5bc28b93a36e ("power_supply: power_supply_read_temp only if use_cnt > 0")
> Fixes: 3be330bf8860 ("power_supply: Register battery as a thermal zone")
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
>  drivers/power/supply/power_supply_core.c | 7 ++++++-
>  1 file changed, 6 insertions(+), 1 deletion(-)

Hi,

This is the friendly patch-bot of Greg Kroah-Hartman.  You have sent him
a patch that has triggered this response.  He used to manually respond
to these common problems, but in order to save his sanity (he kept
writing the same thing over and over, yet to different people), I was
created.  Hopefully you will not take offence and will fix the problem
in your patch and resubmit it so that it can be accepted into the Linux
kernel tree.

You are receiving this message because of the following common error(s)
as indicated below:

- You have marked a patch with a "Fixes:" tag for a commit that is in an
  older released kernel, yet you do not have a cc: stable line in the
  signed-off-by area at all, which means that the patch will not be
  applied to any older kernel releases.  To properly fix this, please
  follow the documented rules in the
  Documentation/process/stable-kernel-rules.rst file for how to resolve
  this.

If you wish to discuss this problem further, or you have questions about
how to resolve this issue, please feel free to respond to this email and
Greg will reply once he has dug out from the pending patches received
from other developers.

thanks,

greg k-h's patch email bot
Daniel Lezcano July 4, 2024, 4:41 p.m. UTC | #2
On 04/07/2024 10:52, Neil Armstrong wrote:
> If the thermal core tries to update the temperature from an
> uninitialized power supply, it will swawn the following warning:
> thermal thermal_zoneXX: failed to read out thermal zone (-19)
> 
> But reading from an uninitialized power supply should not be
> considered as a fatal error, but the thermal core expects
> the -EAGAIN error to be returned in this particular case.
> 
> So convert -ENODEV as -EAGAIN to express the fact that reading
> temperature from an uninitialized power supply shouldn't be
> a fatal error, but should indicate to the thermal zone it should
> retry later.
> 
> It notably removes such messages on Qualcomm platforms using the
> qcom_battmgr driver spawning warnings until the aDSP firmware
> gets up and the battery manager reports valid data.

Is it possible to have the aDSP firmware ready first ?

> Link: https://lore.kernel.org/all/2ed4c630-204a-4f80-a37f-f2ca838eb455@linaro.org/
> Fixes: 5bc28b93a36e ("power_supply: power_supply_read_temp only if use_cnt > 0")
> Fixes: 3be330bf8860 ("power_supply: Register battery as a thermal zone")
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
>   drivers/power/supply/power_supply_core.c | 7 ++++++-
>   1 file changed, 6 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/power/supply/power_supply_core.c b/drivers/power/supply/power_supply_core.c
> index 8f6025acd10a..b38bff4dbfc7 100644
> --- a/drivers/power/supply/power_supply_core.c
> +++ b/drivers/power/supply/power_supply_core.c
> @@ -1287,8 +1287,13 @@ static int power_supply_read_temp(struct thermal_zone_device *tzd,
>   	WARN_ON(tzd == NULL);
>   	psy = thermal_zone_device_priv(tzd);
>   	ret = power_supply_get_property(psy, POWER_SUPPLY_PROP_TEMP, &val);
> +	/*
> +	 * The thermal core expects -EAGAIN as non-fatal error,
> +	 * convert -ENODEV as -EAGAIN since -ENODEV is returned
> +	 * when a power supply device isn't initialized
> +	 */
>   	if (ret)
> -		return ret;
> +		return ret == -ENODEV ? -EAGAIN : ret;
>   
>   	/* Convert tenths of degree Celsius to milli degree Celsius. */
>   	*temp = val.intval * 100;
> 
> ---
> base-commit: 82e4255305c554b0bb18b7ccf2db86041b4c8b6e
> change-id: 20240704-topic-sm8x50-upstream-fix-battmgr-temp-tz-warn-077166861efb
> 
> Best regards,
Krzysztof Kozlowski July 5, 2024, 5:56 a.m. UTC | #3
On 04/07/2024 18:41, Daniel Lezcano wrote:
> On 04/07/2024 10:52, Neil Armstrong wrote:
>> If the thermal core tries to update the temperature from an
>> uninitialized power supply, it will swawn the following warning:
>> thermal thermal_zoneXX: failed to read out thermal zone (-19)
>>
>> But reading from an uninitialized power supply should not be
>> considered as a fatal error, but the thermal core expects
>> the -EAGAIN error to be returned in this particular case.
>>
>> So convert -ENODEV as -EAGAIN to express the fact that reading
>> temperature from an uninitialized power supply shouldn't be
>> a fatal error, but should indicate to the thermal zone it should
>> retry later.
>>
>> It notably removes such messages on Qualcomm platforms using the
>> qcom_battmgr driver spawning warnings until the aDSP firmware
>> gets up and the battery manager reports valid data.
> 
> Is it possible to have the aDSP firmware ready first ?

I don't think so. ADSP firmware is a file, so as every firmware it can
be loaded from rootfs, not initramfs (unlike this driver), or even missing.

Best regards,
Krzysztof
Daniel Lezcano July 5, 2024, 8:08 a.m. UTC | #4
On 05/07/2024 07:56, Krzysztof Kozlowski wrote:
> On 04/07/2024 18:41, Daniel Lezcano wrote:
>> On 04/07/2024 10:52, Neil Armstrong wrote:
>>> If the thermal core tries to update the temperature from an
>>> uninitialized power supply, it will swawn the following warning:
>>> thermal thermal_zoneXX: failed to read out thermal zone (-19)
>>>
>>> But reading from an uninitialized power supply should not be
>>> considered as a fatal error, but the thermal core expects
>>> the -EAGAIN error to be returned in this particular case.
>>>
>>> So convert -ENODEV as -EAGAIN to express the fact that reading
>>> temperature from an uninitialized power supply shouldn't be
>>> a fatal error, but should indicate to the thermal zone it should
>>> retry later.
>>>
>>> It notably removes such messages on Qualcomm platforms using the
>>> qcom_battmgr driver spawning warnings until the aDSP firmware
>>> gets up and the battery manager reports valid data.
>>
>> Is it possible to have the aDSP firmware ready first ?
> 
> I don't think so. ADSP firmware is a file, so as every firmware it can
> be loaded from rootfs, not initramfs (unlike this driver), or even missing.

Ok, said differently, can't we initialize the thermal zone after the 
firmware is loaded ?
Neil Armstrong July 15, 2024, 9:30 a.m. UTC | #5
On 05/07/2024 10:08, Daniel Lezcano wrote:
> On 05/07/2024 07:56, Krzysztof Kozlowski wrote:
>> On 04/07/2024 18:41, Daniel Lezcano wrote:
>>> On 04/07/2024 10:52, Neil Armstrong wrote:
>>>> If the thermal core tries to update the temperature from an
>>>> uninitialized power supply, it will swawn the following warning:
>>>> thermal thermal_zoneXX: failed to read out thermal zone (-19)
>>>>
>>>> But reading from an uninitialized power supply should not be
>>>> considered as a fatal error, but the thermal core expects
>>>> the -EAGAIN error to be returned in this particular case.
>>>>
>>>> So convert -ENODEV as -EAGAIN to express the fact that reading
>>>> temperature from an uninitialized power supply shouldn't be
>>>> a fatal error, but should indicate to the thermal zone it should
>>>> retry later.
>>>>
>>>> It notably removes such messages on Qualcomm platforms using the
>>>> qcom_battmgr driver spawning warnings until the aDSP firmware
>>>> gets up and the battery manager reports valid data.
>>>
>>> Is it possible to have the aDSP firmware ready first ?
>>
>> I don't think so. ADSP firmware is a file, so as every firmware it can
>> be loaded from rootfs, not initramfs (unlike this driver), or even missing.
> 
> Ok, said differently, can't we initialize the thermal zone after the firmware is loaded ?

This is the goal, but this can't be a fix but a proper rework.

> 

I think changing power_supply_core.c is not the right solution.

qcom_battmgr_bat_get_property() should return -EAGAIN instead of
-ENODEV.

Neil
Daniel Lezcano July 15, 2024, 9:41 a.m. UTC | #6
On 15/07/2024 11:30, Neil Armstrong wrote:
> On 05/07/2024 10:08, Daniel Lezcano wrote:
>> On 05/07/2024 07:56, Krzysztof Kozlowski wrote:
>>> On 04/07/2024 18:41, Daniel Lezcano wrote:
>>>> On 04/07/2024 10:52, Neil Armstrong wrote:
>>>>> If the thermal core tries to update the temperature from an
>>>>> uninitialized power supply, it will swawn the following warning:
>>>>> thermal thermal_zoneXX: failed to read out thermal zone (-19)
>>>>>
>>>>> But reading from an uninitialized power supply should not be
>>>>> considered as a fatal error, but the thermal core expects
>>>>> the -EAGAIN error to be returned in this particular case.
>>>>>
>>>>> So convert -ENODEV as -EAGAIN to express the fact that reading
>>>>> temperature from an uninitialized power supply shouldn't be
>>>>> a fatal error, but should indicate to the thermal zone it should
>>>>> retry later.
>>>>>
>>>>> It notably removes such messages on Qualcomm platforms using the
>>>>> qcom_battmgr driver spawning warnings until the aDSP firmware
>>>>> gets up and the battery manager reports valid data.
>>>>
>>>> Is it possible to have the aDSP firmware ready first ?
>>>
>>> I don't think so. ADSP firmware is a file, so as every firmware it can
>>> be loaded from rootfs, not initramfs (unlike this driver), or even 
>>> missing.
>>
>> Ok, said differently, can't we initialize the thermal zone after the 
>> firmware is loaded ?
> 
> This is the goal, but this can't be a fix but a proper rework.

Right, it is a design issue and we are finding this problem in several 
drivers using the thermal zone. Unfortunately that forces the thermal 
core to do cumbersome mechanisms because of this and obviously it is a 
friction for thermal core cleanups / rework. IOW, bad driver design => 
thermal core impacted.

> I think changing power_supply_core.c is not the right solution.

 From my POV, it is the right solution but I agree it could take a cycle 
or more to fix.

> qcom_battmgr_bat_get_property() should return -EAGAIN instead of
> -ENODEV.

Yes, we can do that in the first place and come back to solve this 
firmware / async issue in a more generic way later
diff mbox series

Patch

diff --git a/drivers/power/supply/power_supply_core.c b/drivers/power/supply/power_supply_core.c
index 8f6025acd10a..b38bff4dbfc7 100644
--- a/drivers/power/supply/power_supply_core.c
+++ b/drivers/power/supply/power_supply_core.c
@@ -1287,8 +1287,13 @@  static int power_supply_read_temp(struct thermal_zone_device *tzd,
 	WARN_ON(tzd == NULL);
 	psy = thermal_zone_device_priv(tzd);
 	ret = power_supply_get_property(psy, POWER_SUPPLY_PROP_TEMP, &val);
+	/*
+	 * The thermal core expects -EAGAIN as non-fatal error,
+	 * convert -ENODEV as -EAGAIN since -ENODEV is returned
+	 * when a power supply device isn't initialized
+	 */
 	if (ret)
-		return ret;
+		return ret == -ENODEV ? -EAGAIN : ret;
 
 	/* Convert tenths of degree Celsius to milli degree Celsius. */
 	*temp = val.intval * 100;