| Message ID | 20240715110251.261844-4-heiko@sntech.de (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
| Series | Binding and driver for voltage controlled oscillators | expand |
Hi Heiko, On Mon, 15 Jul 2024 at 16:35, Heiko Stuebner <heiko@sntech.de> wrote: > > The Rock 5 ITX uses two PCIe controllers to drive both a M.2 slot and its > SATA controller with 2 lanes each. The supply for the refclk oscillator is > the same that supplies the M.2 slot, but the SATA controller port is > supplied by a different rail. > > This leads to the effect that if the PCIe30x4 controller for the M.2 > probes first, everything works normally. But if the PCIe30x2 controller > that is connected to the SATA controller probes first, it will hang on > the first DBI read as nothing will have enabled the refclock before. > I just checked the rk3588-rock-5-itx.dts in the linux-next. You have not enabled sata0 and sata2, which might be the problem for the SATA controller not getting initialized. Thanks -Anand > Fix this by describing the clock generator with its supplies so that > both controllers can reference it as needed. > > Signed-off-by: Heiko Stuebner <heiko@sntech.de> > --- > .../boot/dts/rockchip/rk3588-rock-5-itx.dts | 38 ++++++++++++++++++- > 1 file changed, 36 insertions(+), 2 deletions(-) > > diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts > index d0b922b8d67e8..37bc53f2796fc 100644 > --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts > +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts > @@ -72,6 +72,15 @@ hdd-led2 { > }; > }; > > + /* Unnamed voltage oscillator: 100MHz,3.3V,3225 */ > + pcie30_port0_refclk: pcie30_port1_refclk: pcie-voltage-oscillator { > + compatible = "voltage-oscillator"; > + #clock-cells = <0>; > + clock-frequency = <100000000>; > + clock-output-names = "pcie30_refclk"; > + vdd-supply = <&vcc3v3_pi6c_05>; > + }; > + > fan0: pwm-fan { > compatible = "pwm-fan"; > #cooling-cells = <2>; > @@ -146,13 +155,14 @@ vcc3v3_lan: vcc3v3_lan_phy2: regulator-vcc3v3-lan { > vin-supply = <&vcc_3v3_s3>; > }; > > - vcc3v3_mkey: regulator-vcc3v3-mkey { > + /* The PCIE30x4_PWREN_H controls two regulators */ > + vcc3v3_mkey: vcc3v3_pi6c_05: regulator-vcc3v3-pi6c-05 { > compatible = "regulator-fixed"; > enable-active-high; > gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; > pinctrl-names = "default"; > pinctrl-0 = <&pcie30x4_pwren_h>; > - regulator-name = "vcc3v3_mkey"; > + regulator-name = "vcc3v3_pi6c_05"; > regulator-min-microvolt = <3300000>; > regulator-max-microvolt = <3300000>; > startup-delay-us = <5000>; > @@ -513,6 +523,18 @@ &pcie30phy { > > /* ASMedia ASM1164 Sata controller */ > &pcie3x2 { > + /* > + * The board has a "pcie_refclk" oscillator that needs enabling, > + * so add it to the list of clocks. > + */ > + clocks = <&cru ACLK_PCIE_2L_MSTR>, <&cru ACLK_PCIE_2L_SLV>, > + <&cru ACLK_PCIE_2L_DBI>, <&cru PCLK_PCIE_2L>, > + <&cru CLK_PCIE_AUX1>, <&cru CLK_PCIE2L_PIPE>, > + <&pcie30_port1_refclk>; > + clock-names = "aclk_mst", "aclk_slv", > + "aclk_dbi", "pclk", > + "aux", "pipe", > + "ref"; > pinctrl-names = "default"; > pinctrl-0 = <&pcie30x2_perstn_m1_l>; > reset-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>; > @@ -522,6 +544,18 @@ &pcie3x2 { > > /* M.2 M.key */ > &pcie3x4 { > + /* > + * The board has a "pcie_refclk" oscillator that needs enabling, > + * so add it to the list of clocks. > + */ > + clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>, > + <&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>, > + <&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>, > + <&pcie30_port0_refclk>; > + clock-names = "aclk_mst", "aclk_slv", > + "aclk_dbi", "pclk", > + "aux", "pipe", > + "ref"; > num-lanes = <2>; > pinctrl-names = "default"; > pinctrl-0 = <&pcie30x4_perstn_m1_l>; > -- > 2.39.2 > > > _______________________________________________ > Linux-rockchip mailing list > Linux-rockchip@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-rockchip
Hello Anand, On 2024-07-18 09:26, Anand Moon wrote: > On Mon, 15 Jul 2024 at 16:35, Heiko Stuebner <heiko@sntech.de> wrote: >> >> The Rock 5 ITX uses two PCIe controllers to drive both a M.2 slot and >> its >> SATA controller with 2 lanes each. The supply for the refclk >> oscillator is >> the same that supplies the M.2 slot, but the SATA controller port is >> supplied by a different rail. >> >> This leads to the effect that if the PCIe30x4 controller for the M.2 >> probes first, everything works normally. But if the PCIe30x2 >> controller >> that is connected to the SATA controller probes first, it will hang on >> the first DBI read as nothing will have enabled the refclock before. > > I just checked the rk3588-rock-5-itx.dts in the linux-next. > You have not enabled sata0 and sata2, which might be the problem > for the SATA controller not getting initialized. Rock 5 ITX doesn't use RK5588's built-in SATA interfaces, so that's fine. Please have a look at the board schematic, it uses a separate PCI Express SATA controller for its four SATA ports. >> Fix this by describing the clock generator with its supplies so that >> both controllers can reference it as needed. >> >> Signed-off-by: Heiko Stuebner <heiko@sntech.de> >> --- >> .../boot/dts/rockchip/rk3588-rock-5-itx.dts | 38 >> ++++++++++++++++++- >> 1 file changed, 36 insertions(+), 2 deletions(-) >> >> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts >> b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts >> index d0b922b8d67e8..37bc53f2796fc 100644 >> --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts >> +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts >> @@ -72,6 +72,15 @@ hdd-led2 { >> }; >> }; >> >> + /* Unnamed voltage oscillator: 100MHz,3.3V,3225 */ >> + pcie30_port0_refclk: pcie30_port1_refclk: >> pcie-voltage-oscillator { >> + compatible = "voltage-oscillator"; >> + #clock-cells = <0>; >> + clock-frequency = <100000000>; >> + clock-output-names = "pcie30_refclk"; >> + vdd-supply = <&vcc3v3_pi6c_05>; >> + }; >> + >> fan0: pwm-fan { >> compatible = "pwm-fan"; >> #cooling-cells = <2>; >> @@ -146,13 +155,14 @@ vcc3v3_lan: vcc3v3_lan_phy2: >> regulator-vcc3v3-lan { >> vin-supply = <&vcc_3v3_s3>; >> }; >> >> - vcc3v3_mkey: regulator-vcc3v3-mkey { >> + /* The PCIE30x4_PWREN_H controls two regulators */ >> + vcc3v3_mkey: vcc3v3_pi6c_05: regulator-vcc3v3-pi6c-05 { >> compatible = "regulator-fixed"; >> enable-active-high; >> gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; >> pinctrl-names = "default"; >> pinctrl-0 = <&pcie30x4_pwren_h>; >> - regulator-name = "vcc3v3_mkey"; >> + regulator-name = "vcc3v3_pi6c_05"; >> regulator-min-microvolt = <3300000>; >> regulator-max-microvolt = <3300000>; >> startup-delay-us = <5000>; >> @@ -513,6 +523,18 @@ &pcie30phy { >> >> /* ASMedia ASM1164 Sata controller */ >> &pcie3x2 { >> + /* >> + * The board has a "pcie_refclk" oscillator that needs >> enabling, >> + * so add it to the list of clocks. >> + */ >> + clocks = <&cru ACLK_PCIE_2L_MSTR>, <&cru ACLK_PCIE_2L_SLV>, >> + <&cru ACLK_PCIE_2L_DBI>, <&cru PCLK_PCIE_2L>, >> + <&cru CLK_PCIE_AUX1>, <&cru CLK_PCIE2L_PIPE>, >> + <&pcie30_port1_refclk>; >> + clock-names = "aclk_mst", "aclk_slv", >> + "aclk_dbi", "pclk", >> + "aux", "pipe", >> + "ref"; >> pinctrl-names = "default"; >> pinctrl-0 = <&pcie30x2_perstn_m1_l>; >> reset-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>; >> @@ -522,6 +544,18 @@ &pcie3x2 { >> >> /* M.2 M.key */ >> &pcie3x4 { >> + /* >> + * The board has a "pcie_refclk" oscillator that needs >> enabling, >> + * so add it to the list of clocks. >> + */ >> + clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>, >> + <&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>, >> + <&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>, >> + <&pcie30_port0_refclk>; >> + clock-names = "aclk_mst", "aclk_slv", >> + "aclk_dbi", "pclk", >> + "aux", "pipe", >> + "ref"; >> num-lanes = <2>; >> pinctrl-names = "default"; >> pinctrl-0 = <&pcie30x4_perstn_m1_l>; >> -- >> 2.39.2
Hi Dragan, On Thu, 18 Jul 2024 at 13:02, Dragan Simic <dsimic@manjaro.org> wrote: > > Hello Anand, > > On 2024-07-18 09:26, Anand Moon wrote: > > On Mon, 15 Jul 2024 at 16:35, Heiko Stuebner <heiko@sntech.de> wrote: > >> > >> The Rock 5 ITX uses two PCIe controllers to drive both a M.2 slot and > >> its > >> SATA controller with 2 lanes each. The supply for the refclk > >> oscillator is > >> the same that supplies the M.2 slot, but the SATA controller port is > >> supplied by a different rail. > >> > >> This leads to the effect that if the PCIe30x4 controller for the M.2 > >> probes first, everything works normally. But if the PCIe30x2 > >> controller > >> that is connected to the SATA controller probes first, it will hang on > >> the first DBI read as nothing will have enabled the refclock before. > > > > I just checked the rk3588-rock-5-itx.dts in the linux-next. > > You have not enabled sata0 and sata2, which might be the problem > > for the SATA controller not getting initialized. > > Rock 5 ITX doesn't use RK5588's built-in SATA interfaces, so that's > fine. > Please have a look at the board schematic, it uses a separate PCI > Express > SATA controller for its four SATA ports. > yes, But I am referring to sata node not enabled which enable the PHY_TYPE_SATA. see rk3588-coolpi-cm5-evb.dts and rk3588-edgeble-neu6a-io.dtsi rk3588-quartzpro64.dts which have sata port on board. &sata0 { status = "okay"; }; Thanks -Anand
On 2024-07-18 09:52, Anand Moon wrote: > On Thu, 18 Jul 2024 at 13:02, Dragan Simic <dsimic@manjaro.org> wrote: >> On 2024-07-18 09:26, Anand Moon wrote: >> > On Mon, 15 Jul 2024 at 16:35, Heiko Stuebner <heiko@sntech.de> wrote: >> >> >> >> The Rock 5 ITX uses two PCIe controllers to drive both a M.2 slot and >> >> its >> >> SATA controller with 2 lanes each. The supply for the refclk >> >> oscillator is >> >> the same that supplies the M.2 slot, but the SATA controller port is >> >> supplied by a different rail. >> >> >> >> This leads to the effect that if the PCIe30x4 controller for the M.2 >> >> probes first, everything works normally. But if the PCIe30x2 >> >> controller >> >> that is connected to the SATA controller probes first, it will hang on >> >> the first DBI read as nothing will have enabled the refclock before. >> > >> > I just checked the rk3588-rock-5-itx.dts in the linux-next. >> > You have not enabled sata0 and sata2, which might be the problem >> > for the SATA controller not getting initialized. >> >> Rock 5 ITX doesn't use RK5588's built-in SATA interfaces, so that's >> fine. >> Please have a look at the board schematic, it uses a separate PCI >> Express >> SATA controller for its four SATA ports. >> > yes, But I am referring to sata node not enabled which enable > the PHY_TYPE_SATA. > > see rk3588-coolpi-cm5-evb.dts and rk3588-edgeble-neu6a-io.dtsi > rk3588-quartzpro64.dts > which have sata port on board. > > &sata0 { > status = "okay"; > }; QuartzPro64, as an example, uses RK3588's built-in SATA interfaces, so it enables sata0 in its board dts. Rock 5 ITX doesn't do that, as I already described.
Hi Dragan On Thu, 18 Jul 2024 at 13:28, Dragan Simic <dsimic@manjaro.org> wrote: > > On 2024-07-18 09:52, Anand Moon wrote: > > On Thu, 18 Jul 2024 at 13:02, Dragan Simic <dsimic@manjaro.org> wrote: > >> On 2024-07-18 09:26, Anand Moon wrote: > >> > On Mon, 15 Jul 2024 at 16:35, Heiko Stuebner <heiko@sntech.de> wrote: > >> >> > >> >> The Rock 5 ITX uses two PCIe controllers to drive both a M.2 slot and > >> >> its > >> >> SATA controller with 2 lanes each. The supply for the refclk > >> >> oscillator is > >> >> the same that supplies the M.2 slot, but the SATA controller port is > >> >> supplied by a different rail. > >> >> > >> >> This leads to the effect that if the PCIe30x4 controller for the M.2 > >> >> probes first, everything works normally. But if the PCIe30x2 > >> >> controller > >> >> that is connected to the SATA controller probes first, it will hang on > >> >> the first DBI read as nothing will have enabled the refclock before. > >> > > >> > I just checked the rk3588-rock-5-itx.dts in the linux-next. > >> > You have not enabled sata0 and sata2, which might be the problem > >> > for the SATA controller not getting initialized. > >> > >> Rock 5 ITX doesn't use RK5588's built-in SATA interfaces, so that's > >> fine. > >> Please have a look at the board schematic, it uses a separate PCI > >> Express > >> SATA controller for its four SATA ports. > >> > > yes, But I am referring to sata node not enabled which enable > > the PHY_TYPE_SATA. > > > > see rk3588-coolpi-cm5-evb.dts and rk3588-edgeble-neu6a-io.dtsi > > rk3588-quartzpro64.dts > > which have sata port on board. > > > > &sata0 { > > status = "okay"; > > }; > > QuartzPro64, as an example, uses RK3588's built-in SATA interfaces, > so it enables sata0 in its board dts. Rock 5 ITX doesn't do that, > as I already described. Ok no problem, Thanks -Anand
Am Donnerstag, 18. Juli 2024, 10:00:51 CEST schrieb Anand Moon: > Hi Dragan > > On Thu, 18 Jul 2024 at 13:28, Dragan Simic <dsimic@manjaro.org> wrote: > > > > On 2024-07-18 09:52, Anand Moon wrote: > > > On Thu, 18 Jul 2024 at 13:02, Dragan Simic <dsimic@manjaro.org> wrote: > > >> On 2024-07-18 09:26, Anand Moon wrote: > > >> > On Mon, 15 Jul 2024 at 16:35, Heiko Stuebner <heiko@sntech.de> wrote: > > >> >> > > >> >> The Rock 5 ITX uses two PCIe controllers to drive both a M.2 slot and > > >> >> its > > >> >> SATA controller with 2 lanes each. The supply for the refclk > > >> >> oscillator is > > >> >> the same that supplies the M.2 slot, but the SATA controller port is > > >> >> supplied by a different rail. > > >> >> > > >> >> This leads to the effect that if the PCIe30x4 controller for the M.2 > > >> >> probes first, everything works normally. But if the PCIe30x2 > > >> >> controller > > >> >> that is connected to the SATA controller probes first, it will hang on > > >> >> the first DBI read as nothing will have enabled the refclock before. > > >> > > > >> > I just checked the rk3588-rock-5-itx.dts in the linux-next. > > >> > You have not enabled sata0 and sata2, which might be the problem > > >> > for the SATA controller not getting initialized. > > >> > > >> Rock 5 ITX doesn't use RK5588's built-in SATA interfaces, so that's > > >> fine. > > >> Please have a look at the board schematic, it uses a separate PCI > > >> Express > > >> SATA controller for its four SATA ports. > > >> > > > yes, But I am referring to sata node not enabled which enable > > > the PHY_TYPE_SATA. > > > > > > see rk3588-coolpi-cm5-evb.dts and rk3588-edgeble-neu6a-io.dtsi > > > rk3588-quartzpro64.dts > > > which have sata port on board. > > > > > > &sata0 { > > > status = "okay"; > > > }; > > > > QuartzPro64, as an example, uses RK3588's built-in SATA interfaces, > > so it enables sata0 in its board dts. Rock 5 ITX doesn't do that, > > as I already described. > > Ok no problem, For the Rock 5 ITX it really only routes 2 PCIe lanes to one M.2 port and the other 2 lanes to the separate ASMedia SATA controller. So from the Rock5 PoV, it's really just 2 PCIe 2-lane slots and the SATA controller simply gets probed as PCIe device. I even have a sample of the Rock 5+ here, that actually drops the separate SATA controller and instead provides a 2nd M.2 slot ;-) Heiko
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts index d0b922b8d67e8..37bc53f2796fc 100644 --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts @@ -72,6 +72,15 @@ hdd-led2 { }; }; + /* Unnamed voltage oscillator: 100MHz,3.3V,3225 */ + pcie30_port0_refclk: pcie30_port1_refclk: pcie-voltage-oscillator { + compatible = "voltage-oscillator"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "pcie30_refclk"; + vdd-supply = <&vcc3v3_pi6c_05>; + }; + fan0: pwm-fan { compatible = "pwm-fan"; #cooling-cells = <2>; @@ -146,13 +155,14 @@ vcc3v3_lan: vcc3v3_lan_phy2: regulator-vcc3v3-lan { vin-supply = <&vcc_3v3_s3>; }; - vcc3v3_mkey: regulator-vcc3v3-mkey { + /* The PCIE30x4_PWREN_H controls two regulators */ + vcc3v3_mkey: vcc3v3_pi6c_05: regulator-vcc3v3-pi6c-05 { compatible = "regulator-fixed"; enable-active-high; gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pcie30x4_pwren_h>; - regulator-name = "vcc3v3_mkey"; + regulator-name = "vcc3v3_pi6c_05"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; startup-delay-us = <5000>; @@ -513,6 +523,18 @@ &pcie30phy { /* ASMedia ASM1164 Sata controller */ &pcie3x2 { + /* + * The board has a "pcie_refclk" oscillator that needs enabling, + * so add it to the list of clocks. + */ + clocks = <&cru ACLK_PCIE_2L_MSTR>, <&cru ACLK_PCIE_2L_SLV>, + <&cru ACLK_PCIE_2L_DBI>, <&cru PCLK_PCIE_2L>, + <&cru CLK_PCIE_AUX1>, <&cru CLK_PCIE2L_PIPE>, + <&pcie30_port1_refclk>; + clock-names = "aclk_mst", "aclk_slv", + "aclk_dbi", "pclk", + "aux", "pipe", + "ref"; pinctrl-names = "default"; pinctrl-0 = <&pcie30x2_perstn_m1_l>; reset-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>; @@ -522,6 +544,18 @@ &pcie3x2 { /* M.2 M.key */ &pcie3x4 { + /* + * The board has a "pcie_refclk" oscillator that needs enabling, + * so add it to the list of clocks. + */ + clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>, + <&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>, + <&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>, + <&pcie30_port0_refclk>; + clock-names = "aclk_mst", "aclk_slv", + "aclk_dbi", "pclk", + "aux", "pipe", + "ref"; num-lanes = <2>; pinctrl-names = "default"; pinctrl-0 = <&pcie30x4_perstn_m1_l>;
The Rock 5 ITX uses two PCIe controllers to drive both a M.2 slot and its SATA controller with 2 lanes each. The supply for the refclk oscillator is the same that supplies the M.2 slot, but the SATA controller port is supplied by a different rail. This leads to the effect that if the PCIe30x4 controller for the M.2 probes first, everything works normally. But if the PCIe30x2 controller that is connected to the SATA controller probes first, it will hang on the first DBI read as nothing will have enabled the refclock before. Fix this by describing the clock generator with its supplies so that both controllers can reference it as needed. Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- .../boot/dts/rockchip/rk3588-rock-5-itx.dts | 38 ++++++++++++++++++- 1 file changed, 36 insertions(+), 2 deletions(-)