| Message ID | 20240719120853.1924771-1-m.majewski2@samsung.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | Add initial Exynos 850 support to the thermal driver | expand |
Hi Mateusz, On Fri, Jul 19, 2024 at 7:09 AM Mateusz Majewski <m.majewski2@samsung.com> wrote: > > This series adds initial Exynos 850 support to the thermal driver > together with its requirements (tmu_temp_mask fix, making data->clk > optional, adding the new string to dt-bindings), while also cleaning up > a bit (using DEFINE_SIMPLE_DEV_PM_OPS and removing some outdated > information from dt-bindings). > > Mateusz Majewski (6): > drivers/thermal/exynos: use DEFINE_SIMPLE_DEV_PM_OPS > drivers/thermal/exynos: use tmu_temp_mask consistently > drivers/thermal/exynos: check IS_ERR(data->clk) consistently > dt-bindings: thermal: samsung,exynos: add exynos850-tmu string > drivers/thermal/exynos: add initial Exynos 850 support > dt-bindings: thermal: samsung,exynos: remove outdated information on > trip point count > > .../thermal/samsung,exynos-thermal.yaml | 33 ++- > drivers/thermal/samsung/exynos_tmu.c | 279 +++++++++++++++--- > 2 files changed, 270 insertions(+), 42 deletions(-) > > -- Thank you for the contribution! Did you by chance test it on any hardware, perhaps on E850-96 board? Just noticed there are no dts changes in this series (or as separate patches). If no -- I'll be glad to assist you on that, if you can share dts definitions for E850-96 and the testing instructions with me. Thanks! > 2.45.1 > >
Hi :) > Thank you for the contribution! Did you by chance test it on any > hardware, perhaps on E850-96 board? Just noticed there are no dts > changes in this series (or as separate patches). If no -- I'll be glad > to assist you on that, if you can share dts definitions for E850-96 > and the testing instructions with me. I did test it on our copy of E850-96. I used this for testing: diff --git a/arch/arm64/boot/dts/exynos/exynos850.dtsi b/arch/arm64/boot/dts/exynos/exynos850.dtsi index f1c8b4613cbc..cffc173fd059 100644 --- a/arch/arm64/boot/dts/exynos/exynos850.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos850.dtsi @@ -617,6 +617,53 @@ sysreg_cmgp: syscon@11c20000 { clocks = <&cmu_cmgp CLK_GOUT_SYSREG_CMGP_PCLK>; }; + tmuctrl_0: tmu@10070000{ + compatible = "samsung,exynos850-tmu"; + reg = <0x10070000 0x800>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; + #thermal-sensor-cells = <0>; + }; + + thermal-zones { + test_thermal: test-thermal{ + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tmuctrl_0>; + trips { + test_40000: test-40000 { + temperature = <40000>; + hysteresis = <1000>; + type = "passive"; + }; + test_50000: test-50000 { + temperature = <50000>; + hysteresis = <1000>; + type = "passive"; + }; + test_60000: test-60000 { + temperature = <60000>; + hysteresis = <1000>; + type = "passive"; + }; + test_70000: test-70000 { + temperature = <70000>; + hysteresis = <1000>; + type = "passive"; + }; + test_80000: test-80000 { + temperature = <80000>; + hysteresis = <1000>; + type = "passive"; + }; + test_crit: test-crit { + temperature = <90000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + }; + usbdrd: usb@13600000 { compatible = "samsung,exynos850-dwusb3"; ranges = <0x0 0x13600000 0x10000>; I did not post this because it would probably need some more thought, and it probably wouldn't get merged until this series does anyway I think? During testing I couldn't get readings higher than 35C, but the values reacted to CPU load as expected. Also, Marek had physical access to the board while I was testing it and has confirmed that the values are realistic. Some more testing was done with some combination of lowering the trip points, emul_temp and those temporary changes: diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index bd52663f1a5a..8db3f9039e7a 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -941,6 +941,7 @@ static irqreturn_t exynos_tmu_threaded_irq(int irq, void *id) { struct exynos_tmu_data *data = id; + pr_info("interrupt\n"); thermal_zone_device_update(data->tzd, THERMAL_EVENT_UNSPECIFIED); mutex_lock(&data->lock); diff --git a/drivers/thermal/thermal_sysfs.c b/drivers/thermal/thermal_sysfs.c index 72b302bf914e..0864179526e2 100644 --- a/drivers/thermal/thermal_sysfs.c +++ b/drivers/thermal/thermal_sysfs.c @@ -232,13 +232,11 @@ emul_temp_store(struct device *dev, struct device_attribute *attr, mutex_lock(&tz->lock); - if (!tz->ops.set_emul_temp) + if (!tz->ops.set_emul_temp) { tz->emul_temperature = temperature; - else - ret = tz->ops.set_emul_temp(tz, temperature); - - if (!ret) __thermal_zone_device_update(tz, THERMAL_EVENT_UNSPECIFIED); + } else + ret = tz->ops.set_emul_temp(tz, temperature); mutex_unlock(&tz->lock);
On Tue, Jul 23, 2024 at 9:16 AM Mateusz Majewski <m.majewski2@samsung.com> wrote: > > Hi :) > > > Thank you for the contribution! Did you by chance test it on any > > hardware, perhaps on E850-96 board? Just noticed there are no dts > > changes in this series (or as separate patches). If no -- I'll be glad > > to assist you on that, if you can share dts definitions for E850-96 > > and the testing instructions with me. > > I did test it on our copy of E850-96. I used this for testing: > Good to know, thanks for the detailed info, Mateusz! Just wanted to be sure it was tested properly and my help is not needed. Btw, I'm curious what is the reason for implementing TMU? Do you have some use cases where it's needed?
> Btw, I'm > curious what is the reason for implementing TMU? Do you have some use > cases where it's needed? Not really AFAIK? Mostly because we have the hardware, are familiar with this driver, and have some time to do this :)
On Wed, Jul 24, 2024 at 10:31 AM Mateusz Majewski <m.majewski2@samsung.com> wrote: > > > Btw, I'm > > curious what is the reason for implementing TMU? Do you have some use > > cases where it's needed? > > Not really AFAIK? Mostly because we have the hardware, are familiar with > this driver, and have some time to do this :) No complaints from my side! Wish more folks were working on this platform :) Please let me know if I can assist you in any way. Hope in v2 you can account for the TMU clock I enabled in [1], and test it. Thanks! [1] https://lore.kernel.org/linux-samsung-soc/20240723163311.28654-1-semen.protsenko@linaro.org/
This series adds initial Exynos 850 support to the thermal driver together with its requirements (tmu_temp_mask fix, making data->clk optional, adding the new string to dt-bindings), while also cleaning up a bit (using DEFINE_SIMPLE_DEV_PM_OPS and removing some outdated information from dt-bindings). Mateusz Majewski (6): drivers/thermal/exynos: use DEFINE_SIMPLE_DEV_PM_OPS drivers/thermal/exynos: use tmu_temp_mask consistently drivers/thermal/exynos: check IS_ERR(data->clk) consistently dt-bindings: thermal: samsung,exynos: add exynos850-tmu string drivers/thermal/exynos: add initial Exynos 850 support dt-bindings: thermal: samsung,exynos: remove outdated information on trip point count .../thermal/samsung,exynos-thermal.yaml | 33 ++- drivers/thermal/samsung/exynos_tmu.c | 279 +++++++++++++++--- 2 files changed, 270 insertions(+), 42 deletions(-)