| Message ID | 20240820-c3_add_node-v2-3-8fd3f06b7bce@amlogic.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | add some node for amlogic c3 | expand |
On 20/08/2024 11:41, Xianwei Zhao via B4 Relay wrote: > From: Xianwei Zhao <xianwei.zhao@amlogic.com> > > Add Amlogic C3 C308L AW419 board. The corresponding binding > has been applied, therefore, this series does not need to > add a binding corresponding to the AW419 board. > > Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com> > --- > arch/arm64/boot/dts/amlogic/Makefile | 1 + > .../boot/dts/amlogic/amlogic-c3-c308l-aw419.dts | 262 +++++++++++++++++++++ > 2 files changed, 263 insertions(+) > > diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile > index 29417f04f886..2fbda8419c65 100644 > --- a/arch/arm64/boot/dts/amlogic/Makefile > +++ b/arch/arm64/boot/dts/amlogic/Makefile > @@ -2,6 +2,7 @@ > dtb-$(CONFIG_ARCH_MESON) += amlogic-a4-a113l2-ba400.dtb > dtb-$(CONFIG_ARCH_MESON) += amlogic-a5-a113x2-av400.dtb > dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c302x-aw409.dtb > +dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c308l-aw419.dtb > dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-an400.dtb > dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-khadas-vim4.dtb > dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb > diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts b/arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts > new file mode 100644 > index 000000000000..4477a2659e27 > --- /dev/null > +++ b/arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts > @@ -0,0 +1,262 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (c) 2024 Amlogic, Inc. All rights reserved. > + */ > + > +/dts-v1/; > + > +#include "amlogic-c3.dtsi" > + > +/ { > + model = "Amlogic C308l aw419 Development Board"; > + compatible = "amlogic,aw419", "amlogic,c3"; > + interrupt-parent = <&gic>; > + #address-cells = <2>; > + #size-cells = <2>; > + > + aliases { > + serial0 = &uart_b; > + spi0 = &spifc; > + }; > + > + memory@0 { > + device_type = "memory"; > + reg = <0x0 0x0 0x0 0x80000000>; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + /* 9 MiB reserved for ARM Trusted Firmware */ > + secmon_reserved: secmon@7f00000 { > + compatible = "shared-dma-pool"; > + reg = <0x0 0x07f00000 0x0 0x900000>; > + no-map; > + }; > + }; > + > + main_12v: regulator-main-12v { > + compatible = "regulator-fixed"; > + regulator-name = "12V"; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vcc_5v: regulator-vcc-5v { > + compatible = "regulator-fixed"; > + regulator-name = "VCC5V"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&main_12v>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vddq: regulator-vddq { > + compatible = "regulator-fixed"; > + regulator-name = "VDDQ"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + vin-supply = <&main_12v>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vddao_3v3: regulator-vddao-3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "VDDAO3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&main_12v>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vddao_1v8: regulator-vddao-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "VDDAO1V8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vddao_3v3>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ddr4_2v5: regulator-ddr4-2v5 { > + compatible = "regulator-fixed"; > + regulator-name = "DDR4_2V5"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + vin-supply = <&vddao_3v3>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vcc_3v3: regulator-vcc-3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "VCC3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vddao_3v3>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vcc_1v8: regulator-vcc-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "VCC1V8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vcc_3v3>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vdd_1v8: regulator-vdd-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "VDD1V8_BOOT"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vcc_3v3>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vddio_b: regulator-vddio-3v3-b { > + compatible = "regulator-fixed"; > + regulator-name = "VDDIO_B"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vcc_3v3>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sdcard: regulator-sdcard { > + compatible = "regulator-fixed"; > + regulator-name = "SDCARD_POWER"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vddao_3v3>; > + gpio = <&gpio GPIOA_4 GPIO_ACTIVE_LOW>; > + regulator-boot-on; > + regulator-always-on; > + }; > +}; > + > +&uart_b { > + status = "okay"; > +}; > + > +&nand { > + status = "okay"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pinctrl-0 = <&nand_pins>; > + pinctrl-names = "default"; > + > + nand@0 { > + reg = <0>; > + #address-cells = <1>; > + #size-cells = <1>; > + nand-on-flash-bbt; > + > + partition@0 { > + label = "boot"; > + reg = <0x0 0x00200000>; > + }; > + partition@200000 { > + label = "env"; > + reg = <0x00200000 0x00400000>; > + }; > + partition@600000 { > + label = "system"; > + reg = <0x00600000 0x00a00000>; > + }; > + partition@1000000 { > + label = "rootfs"; > + reg = <0x01000000 0x03000000>; > + }; > + partition@4000000 { > + label = "media"; > + reg = <0x04000000 0x8000000>; > + }; > + }; > +}; > + > +ðmac { > + status = "okay"; > + phy-handle = <&internal_ephy>; > + phy-mode = "rmii"; > +}; > + > +&spifc { > + #address-cells = <1>; > + #size-cells = <0>; > + > + pinctrl-0 = <&spifc_pins>; > + pinctrl-names = "default"; > + > + nand@0 { > + compatible = "spi-nand"; > + reg = <0>; > + spi-max-frequency = <83000000>; > + spi-tx-bus-width = <4>; > + spi-rx-bus-width = <4>; > + #address-cells = <1>; > + #size-cells = <1>; > + status = "disabled"; > + > + partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "boot"; > + reg = <0 0x200000>; > + }; > + > + partition@200000 { > + label = "env"; > + reg = <0x200000 0x400000>; > + }; > + > + partition@600000 { > + label = "system"; > + reg = <0x600000 0xa00000>; > + }; > + > + partition@1000000 { > + label = "rootfs"; > + reg = <0x1000000 0x3000000>; > + }; > + > + partition@4000000 { > + label = "data"; > + reg = <0x4000000 0x8000000>; > + }; > + }; > + }; > +}; > + > +&sd { > + status = "okay"; > + pinctrl-0 = <&sdcard_pins>; > + pinctrl-1 = <&sdcard_clk_gate_pins>; > + pinctrl-names = "default","clk-gate"; > + > + bus-width = <4>; > + cap-sd-highspeed; > + max-frequency = <50000000>; > + disable-wp; > + > + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; > + vmmc-supply = <&sdcard>; > + vqmmc-supply = <&sdcard>; > +}; > Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index 29417f04f886..2fbda8419c65 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -2,6 +2,7 @@ dtb-$(CONFIG_ARCH_MESON) += amlogic-a4-a113l2-ba400.dtb dtb-$(CONFIG_ARCH_MESON) += amlogic-a5-a113x2-av400.dtb dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c302x-aw409.dtb +dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c308l-aw419.dtb dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-an400.dtb dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-khadas-vim4.dtb dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts b/arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts new file mode 100644 index 000000000000..4477a2659e27 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts @@ -0,0 +1,262 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2024 Amlogic, Inc. All rights reserved. + */ + +/dts-v1/; + +#include "amlogic-c3.dtsi" + +/ { + model = "Amlogic C308l aw419 Development Board"; + compatible = "amlogic,aw419", "amlogic,c3"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + serial0 = &uart_b; + spi0 = &spifc; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* 9 MiB reserved for ARM Trusted Firmware */ + secmon_reserved: secmon@7f00000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x07f00000 0x0 0x900000>; + no-map; + }; + }; + + main_12v: regulator-main-12v { + compatible = "regulator-fixed"; + regulator-name = "12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-boot-on; + regulator-always-on; + }; + + vcc_5v: regulator-vcc-5v { + compatible = "regulator-fixed"; + regulator-name = "VCC5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&main_12v>; + regulator-boot-on; + regulator-always-on; + }; + + vddq: regulator-vddq { + compatible = "regulator-fixed"; + regulator-name = "VDDQ"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + vin-supply = <&main_12v>; + regulator-boot-on; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao-3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&main_12v>; + regulator-boot-on; + regulator-always-on; + }; + + vddao_1v8: regulator-vddao-1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-boot-on; + regulator-always-on; + }; + + ddr4_2v5: regulator-ddr4-2v5 { + compatible = "regulator-fixed"; + regulator-name = "DDR4_2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + vin-supply = <&vddao_3v3>; + regulator-boot-on; + regulator-always-on; + }; + + vcc_3v3: regulator-vcc-3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vddao_3v3>; + regulator-boot-on; + regulator-always-on; + }; + + vcc_1v8: regulator-vcc-1v8 { + compatible = "regulator-fixed"; + regulator-name = "VCC1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-boot-on; + regulator-always-on; + }; + + vdd_1v8: regulator-vdd-1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDD1V8_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-boot-on; + regulator-always-on; + }; + + vddio_b: regulator-vddio-3v3-b { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_B"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_3v3>; + regulator-boot-on; + regulator-always-on; + }; + + sdcard: regulator-sdcard { + compatible = "regulator-fixed"; + regulator-name = "SDCARD_POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vddao_3v3>; + gpio = <&gpio GPIOA_4 GPIO_ACTIVE_LOW>; + regulator-boot-on; + regulator-always-on; + }; +}; + +&uart_b { + status = "okay"; +}; + +&nand { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-on-flash-bbt; + + partition@0 { + label = "boot"; + reg = <0x0 0x00200000>; + }; + partition@200000 { + label = "env"; + reg = <0x00200000 0x00400000>; + }; + partition@600000 { + label = "system"; + reg = <0x00600000 0x00a00000>; + }; + partition@1000000 { + label = "rootfs"; + reg = <0x01000000 0x03000000>; + }; + partition@4000000 { + label = "media"; + reg = <0x04000000 0x8000000>; + }; + }; +}; + +ðmac { + status = "okay"; + phy-handle = <&internal_ephy>; + phy-mode = "rmii"; +}; + +&spifc { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-0 = <&spifc_pins>; + pinctrl-names = "default"; + + nand@0 { + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <83000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot"; + reg = <0 0x200000>; + }; + + partition@200000 { + label = "env"; + reg = <0x200000 0x400000>; + }; + + partition@600000 { + label = "system"; + reg = <0x600000 0xa00000>; + }; + + partition@1000000 { + label = "rootfs"; + reg = <0x1000000 0x3000000>; + }; + + partition@4000000 { + label = "data"; + reg = <0x4000000 0x8000000>; + }; + }; + }; +}; + +&sd { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-1 = <&sdcard_clk_gate_pins>; + pinctrl-names = "default","clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&sdcard>; + vqmmc-supply = <&sdcard>; +};