| Message ID | 20240805155242.151661-3-biju.das.jz@bp.renesas.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add support for RZ/G2UL Display Unit | expand |
Hi Biju, Thank you for the patch. On Mon, Aug 05, 2024 at 04:52:36PM +0100, Biju Das wrote: > The LCD controller is composed of Frame Compression Processor (FCPVD), > Video Signal Processor (VSPD), and Display Unit (DU). > > It has DPI interface and supports a maximum resolution of WXGA along > with 2 RPFs to support the blending of two picture layers and raster > operations (ROPs). > > The DU module is connected to VSPD. Add RZ/G2UL DU support. > > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> > --- > v2->v3: > * Avoided the line break in rzg2l_du_start_stop() for rstate. > * Replaced port->du_output in struct rzg2l_du_output_routing and > dropped using the port number to indicate the output type in > rzg2l_du_encoders_init(). > * Updated rzg2l_du_r9a07g043u_info and rzg2l_du_r9a07g044_info > v1->v2: > * No change. > --- > drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c | 8 +++++++- > drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c | 18 ++++++++++++++++-- > drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h | 5 +++-- > drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c | 4 ++-- > 4 files changed, 28 insertions(+), 7 deletions(-) > > diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c > index 6e7aac6219be..fd7675c7f181 100644 > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c > @@ -28,6 +28,7 @@ > #include "rzg2l_du_vsp.h" > > #define DU_MCR0 0x00 > +#define DU_MCR0_DPI_OE BIT(0) > #define DU_MCR0_DI_EN BIT(8) > > #define DU_DITR0 0x10 > @@ -216,9 +217,14 @@ static void rzg2l_du_crtc_put(struct rzg2l_du_crtc *rcrtc) > > static void rzg2l_du_start_stop(struct rzg2l_du_crtc *rcrtc, bool start) > { > + struct rzg2l_du_crtc_state *rstate = to_rzg2l_crtc_state(rcrtc->crtc.state); > struct rzg2l_du_device *rcdu = rcrtc->dev; > + u32 val = DU_MCR0_DI_EN; > > - writel(start ? DU_MCR0_DI_EN : 0, rcdu->mmio + DU_MCR0); > + if (rstate->outputs == BIT(RZG2L_DU_OUTPUT_DPAD0)) Is output supposed to contain a single bit, or can it contain multiple bits ? In the first case I would rename it to output, in the second case you should probably use '&' instead of '=='. > + val |= DU_MCR0_DPI_OE; > + > + writel(start ? val : 0, rcdu->mmio + DU_MCR0); > } > > static void rzg2l_du_crtc_start(struct rzg2l_du_crtc *rcrtc) > diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c > index e5eca8691a33..69b8e216ee1a 100644 > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c > @@ -25,21 +25,35 @@ > * Device Information > */ > > +static const struct rzg2l_du_device_info rzg2l_du_r9a07g043u_info = { > + .channels_mask = BIT(0), > + .routes = { > + [RZG2L_DU_OUTPUT_DSI0] = { > + .du_output = RZG2L_DU_OUTPUT_INVALID, > + }, You can drop this entry, as well as the RZG2L_DU_OUTPUT_INVALID macro. See below. > + [RZG2L_DU_OUTPUT_DPAD0] = { > + .possible_outputs = BIT(0), > + .du_output = RZG2L_DU_OUTPUT_DPAD0, > + }, > + }, > +}; > + > static const struct rzg2l_du_device_info rzg2l_du_r9a07g044_info = { > .channels_mask = BIT(0), > .routes = { > [RZG2L_DU_OUTPUT_DSI0] = { > .possible_outputs = BIT(0), > - .port = 0, > + .du_output = RZG2L_DU_OUTPUT_DSI0, > }, > [RZG2L_DU_OUTPUT_DPAD0] = { > .possible_outputs = BIT(0), > - .port = 1, > + .du_output = RZG2L_DU_OUTPUT_DPAD0, > } > } > }; > > static const struct of_device_id rzg2l_du_of_table[] = { > + { .compatible = "renesas,r9a07g043u-du", .data = &rzg2l_du_r9a07g043u_info }, > { .compatible = "renesas,r9a07g044-du", .data = &rzg2l_du_r9a07g044_info }, > { /* sentinel */ } > }; > diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h > index 58806c2a8f2b..ab82b5c86d6e 100644 > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h > @@ -29,7 +29,7 @@ enum rzg2l_du_output { > /* > * struct rzg2l_du_output_routing - Output routing specification > * @possible_outputs: bitmask of possible outputs > - * @port: device tree port number corresponding to this output route > + * @du_output: DU output > * > * The DU has 2 possible outputs (DPAD0, DSI0). Output routing data > * specify the valid SoC outputs, which CRTC can drive the output, and the type > @@ -37,7 +37,7 @@ enum rzg2l_du_output { > */ > struct rzg2l_du_output_routing { > unsigned int possible_outputs; > - unsigned int port; > + unsigned int du_output; > }; > > /* > @@ -53,6 +53,7 @@ struct rzg2l_du_device_info { > #define RZG2L_DU_MAX_CRTCS 1 > #define RZG2L_DU_MAX_VSPS 1 > #define RZG2L_DU_MAX_DSI 1 > +#define RZG2L_DU_OUTPUT_INVALID -1 > > struct rzg2l_du_device { > struct device *dev; > diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > index 07b312b6f81e..361350f2999e 100644 > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > @@ -183,8 +183,8 @@ static int rzg2l_du_encoders_init(struct rzg2l_du_device *rcdu) > > /* Find the output route corresponding to the port number. */ > for (i = 0; i < RZG2L_DU_OUTPUT_MAX; ++i) { > - if (rcdu->info->routes[i].port == ep.port) { > - output = i; > + if (i == rcdu->info->routes[i].du_output) { If I understand the code correctly, this will always be true except for the routes marked with RZG2L_DU_OUTPUT_INVALID, so you will match the first valid route, regardless of the value of ep.port. I don't think that's correct. I would keep the port field in the rzg2l_du_output_routing, drop the newly added du_output field, and use the following logic: for (i = 0; i < RZG2L_DU_OUTPUT_MAX; ++i) { if (rcdu->info->routes[i].possible_outputs && rcdu->info->routes[i].port == ep.port) { output = i; break; } } Testing possible_outputs skips the routes that don't exist for the device, and the ep.port comparison picks the route corresponding to the port. > + output = rcdu->info->routes[i].du_output; > break; > } > }
Hi Laurent, Thanks for the feedback. > -----Original Message----- > From: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Sent: Tuesday, August 13, 2024 8:49 PM > Subject: Re: [PATCH v3 2/4] drm: renesas: rz-du: Add RZ/G2UL DU Support > > Hi Biju, > > Thank you for the patch. > > On Mon, Aug 05, 2024 at 04:52:36PM +0100, Biju Das wrote: > > The LCD controller is composed of Frame Compression Processor (FCPVD), > > Video Signal Processor (VSPD), and Display Unit (DU). > > > > It has DPI interface and supports a maximum resolution of WXGA along > > with 2 RPFs to support the blending of two picture layers and raster > > operations (ROPs). > > > > The DU module is connected to VSPD. Add RZ/G2UL DU support. > > > > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> > > --- > > v2->v3: > > * Avoided the line break in rzg2l_du_start_stop() for rstate. > > * Replaced port->du_output in struct rzg2l_du_output_routing and > > dropped using the port number to indicate the output type in > > rzg2l_du_encoders_init(). > > * Updated rzg2l_du_r9a07g043u_info and rzg2l_du_r9a07g044_info > > v1->v2: > > * No change. > > --- > > drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c | 8 +++++++- > > drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c | 18 ++++++++++++++++-- > > drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h | 5 +++-- > > drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c | 4 ++-- > > 4 files changed, 28 insertions(+), 7 deletions(-) > > > > diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c > > b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c > > index 6e7aac6219be..fd7675c7f181 100644 > > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c > > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c > > @@ -28,6 +28,7 @@ > > #include "rzg2l_du_vsp.h" > > > > #define DU_MCR0 0x00 > > +#define DU_MCR0_DPI_OE BIT(0) > > #define DU_MCR0_DI_EN BIT(8) > > > > #define DU_DITR0 0x10 > > @@ -216,9 +217,14 @@ static void rzg2l_du_crtc_put(struct > > rzg2l_du_crtc *rcrtc) > > > > static void rzg2l_du_start_stop(struct rzg2l_du_crtc *rcrtc, bool > > start) { > > + struct rzg2l_du_crtc_state *rstate = > > +to_rzg2l_crtc_state(rcrtc->crtc.state); > > struct rzg2l_du_device *rcdu = rcrtc->dev; > > + u32 val = DU_MCR0_DI_EN; > > > > - writel(start ? DU_MCR0_DI_EN : 0, rcdu->mmio + DU_MCR0); > > + if (rstate->outputs == BIT(RZG2L_DU_OUTPUT_DPAD0)) > > Is output supposed to contain a single bit, or can it contain multiple bits ? In the first case I > would rename it to output, in the second case you should probably use '&' instead of '=='. It may contain multiple bits for the future SoCs. So, I will use '&' instead. > > > + val |= DU_MCR0_DPI_OE; > > + > > + writel(start ? val : 0, rcdu->mmio + DU_MCR0); > > } > > > > static void rzg2l_du_crtc_start(struct rzg2l_du_crtc *rcrtc) diff > > --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c > > b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c > > index e5eca8691a33..69b8e216ee1a 100644 > > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c > > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c > > @@ -25,21 +25,35 @@ > > * Device Information > > */ > > > > +static const struct rzg2l_du_device_info rzg2l_du_r9a07g043u_info = { > > + .channels_mask = BIT(0), > > + .routes = { > > + [RZG2L_DU_OUTPUT_DSI0] = { > > + .du_output = RZG2L_DU_OUTPUT_INVALID, > > + }, > > You can drop this entry, as well as the RZG2L_DU_OUTPUT_INVALID macro. > See below. OK. > > > + [RZG2L_DU_OUTPUT_DPAD0] = { > > + .possible_outputs = BIT(0), > > + .du_output = RZG2L_DU_OUTPUT_DPAD0, > > + }, > > + }, > > +}; > > + > > static const struct rzg2l_du_device_info rzg2l_du_r9a07g044_info = { > > .channels_mask = BIT(0), > > .routes = { > > [RZG2L_DU_OUTPUT_DSI0] = { > > .possible_outputs = BIT(0), > > - .port = 0, > > + .du_output = RZG2L_DU_OUTPUT_DSI0, > > }, > > [RZG2L_DU_OUTPUT_DPAD0] = { > > .possible_outputs = BIT(0), > > - .port = 1, > > + .du_output = RZG2L_DU_OUTPUT_DPAD0, > > } > > } > > }; > > > > static const struct of_device_id rzg2l_du_of_table[] = { > > + { .compatible = "renesas,r9a07g043u-du", .data = > > +&rzg2l_du_r9a07g043u_info }, > > { .compatible = "renesas,r9a07g044-du", .data = &rzg2l_du_r9a07g044_info }, > > { /* sentinel */ } > > }; > > diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h > > b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h > > index 58806c2a8f2b..ab82b5c86d6e 100644 > > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h > > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h > > @@ -29,7 +29,7 @@ enum rzg2l_du_output { > > /* > > * struct rzg2l_du_output_routing - Output routing specification > > * @possible_outputs: bitmask of possible outputs > > - * @port: device tree port number corresponding to this output route > > + * @du_output: DU output > > * > > * The DU has 2 possible outputs (DPAD0, DSI0). Output routing data > > * specify the valid SoC outputs, which CRTC can drive the output, > > and the type @@ -37,7 +37,7 @@ enum rzg2l_du_output { > > */ > > struct rzg2l_du_output_routing { > > unsigned int possible_outputs; > > - unsigned int port; > > + unsigned int du_output; > > }; > > > > /* > > @@ -53,6 +53,7 @@ struct rzg2l_du_device_info { > > #define RZG2L_DU_MAX_CRTCS 1 > > #define RZG2L_DU_MAX_VSPS 1 > > #define RZG2L_DU_MAX_DSI 1 > > +#define RZG2L_DU_OUTPUT_INVALID -1 > > > > struct rzg2l_du_device { > > struct device *dev; > > diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > > b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > > index 07b312b6f81e..361350f2999e 100644 > > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > > @@ -183,8 +183,8 @@ static int rzg2l_du_encoders_init(struct > > rzg2l_du_device *rcdu) > > > > /* Find the output route corresponding to the port number. */ > > for (i = 0; i < RZG2L_DU_OUTPUT_MAX; ++i) { > > - if (rcdu->info->routes[i].port == ep.port) { > > - output = i; > > + if (i == rcdu->info->routes[i].du_output) { > > If I understand the code correctly, this will always be true except for the routes marked with > RZG2L_DU_OUTPUT_INVALID, so you will match the first valid route, regardless of the value of ep.port. > I don't think that's correct. > > I would keep the port field in the rzg2l_du_output_routing, drop the newly added du_output field, and > use the following logic: > > for (i = 0; i < RZG2L_DU_OUTPUT_MAX; ++i) { > if (rcdu->info->routes[i].possible_outputs && > rcdu->info->routes[i].port == ep.port) { > output = i; > break; > } > } > > Testing possible_outputs skips the routes that don't exist for the device, and the ep.port comparison > picks the route corresponding to the port. Thanks, this will work. Cheers, Biju > > > + output = rcdu->info->routes[i].du_output; > > break; > > } > > } > > -- > Regards, > > Laurent Pinchart
Hi Biju, On Mon, Aug 5, 2024 at 6:22 PM Biju Das <biju.das.jz@bp.renesas.com> wrote: > The LCD controller is composed of Frame Compression Processor (FCPVD), > Video Signal Processor (VSPD), and Display Unit (DU). > > It has DPI interface and supports a maximum resolution of WXGA along > with 2 RPFs to support the blending of two picture layers and raster > operations (ROPs). > > The DU module is connected to VSPD. Add RZ/G2UL DU support. > > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> > --- > v2->v3: > * Avoided the line break in rzg2l_du_start_stop() for rstate. > * Replaced port->du_output in struct rzg2l_du_output_routing and > dropped using the port number to indicate the output type in > rzg2l_du_encoders_init(). > * Updated rzg2l_du_r9a07g043u_info and rzg2l_du_r9a07g044_info Thanks for your patch! > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > @@ -183,8 +183,8 @@ static int rzg2l_du_encoders_init(struct rzg2l_du_device *rcdu) > > /* Find the output route corresponding to the port number. */ > for (i = 0; i < RZG2L_DU_OUTPUT_MAX; ++i) { > - if (rcdu->info->routes[i].port == ep.port) { > - output = i; > + if (i == rcdu->info->routes[i].du_output) { > + output = rcdu->info->routes[i].du_output; Notwithstanding Laurent's comment, the above replacement is equivalent to the original "output = i;", so there is no need to change this line. > break; > } > } Gr{oetje,eeting}s, Geert
Hi Geert Uytterhoeven, Thanks for the feedback. > -----Original Message----- > From: Geert Uytterhoeven <geert@linux-m68k.org> > Sent: Thursday, August 22, 2024 1:31 PM > Subject: Re: [PATCH v3 2/4] drm: renesas: rz-du: Add RZ/G2UL DU Support > > Hi Biju, > > On Mon, Aug 5, 2024 at 6:22 PM Biju Das <biju.das.jz@bp.renesas.com> wrote: > > The LCD controller is composed of Frame Compression Processor (FCPVD), > > Video Signal Processor (VSPD), and Display Unit (DU). > > > > It has DPI interface and supports a maximum resolution of WXGA along > > with 2 RPFs to support the blending of two picture layers and raster > > operations (ROPs). > > > > The DU module is connected to VSPD. Add RZ/G2UL DU support. > > > > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> > > --- > > v2->v3: > > * Avoided the line break in rzg2l_du_start_stop() for rstate. > > * Replaced port->du_output in struct rzg2l_du_output_routing and > > dropped using the port number to indicate the output type in > > rzg2l_du_encoders_init(). > > * Updated rzg2l_du_r9a07g043u_info and rzg2l_du_r9a07g044_info > > Thanks for your patch! > > > --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > > +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c > > @@ -183,8 +183,8 @@ static int rzg2l_du_encoders_init(struct > > rzg2l_du_device *rcdu) > > > > /* Find the output route corresponding to the port number. */ > > for (i = 0; i < RZG2L_DU_OUTPUT_MAX; ++i) { > > - if (rcdu->info->routes[i].port == ep.port) { > > - output = i; > > + if (i == rcdu->info->routes[i].du_output) { > > + output = > > + rcdu->info->routes[i].du_output; > > Notwithstanding Laurent's comment, the above replacement is equivalent to the original "output = i;", > so there is no need to change this line. Agreed. I missed that. Cheers, Biju > > > break; > > } > > } > > Gr{oetje,eeting}s, > > Geert > > -- > Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org > > In personal conversations with technical people, I call myself a hacker. But when I'm talking to > journalists I just say "programmer" or something like that. > -- Linus Torvalds
diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c index 6e7aac6219be..fd7675c7f181 100644 --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c @@ -28,6 +28,7 @@ #include "rzg2l_du_vsp.h" #define DU_MCR0 0x00 +#define DU_MCR0_DPI_OE BIT(0) #define DU_MCR0_DI_EN BIT(8) #define DU_DITR0 0x10 @@ -216,9 +217,14 @@ static void rzg2l_du_crtc_put(struct rzg2l_du_crtc *rcrtc) static void rzg2l_du_start_stop(struct rzg2l_du_crtc *rcrtc, bool start) { + struct rzg2l_du_crtc_state *rstate = to_rzg2l_crtc_state(rcrtc->crtc.state); struct rzg2l_du_device *rcdu = rcrtc->dev; + u32 val = DU_MCR0_DI_EN; - writel(start ? DU_MCR0_DI_EN : 0, rcdu->mmio + DU_MCR0); + if (rstate->outputs == BIT(RZG2L_DU_OUTPUT_DPAD0)) + val |= DU_MCR0_DPI_OE; + + writel(start ? val : 0, rcdu->mmio + DU_MCR0); } static void rzg2l_du_crtc_start(struct rzg2l_du_crtc *rcrtc) diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c index e5eca8691a33..69b8e216ee1a 100644 --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c @@ -25,21 +25,35 @@ * Device Information */ +static const struct rzg2l_du_device_info rzg2l_du_r9a07g043u_info = { + .channels_mask = BIT(0), + .routes = { + [RZG2L_DU_OUTPUT_DSI0] = { + .du_output = RZG2L_DU_OUTPUT_INVALID, + }, + [RZG2L_DU_OUTPUT_DPAD0] = { + .possible_outputs = BIT(0), + .du_output = RZG2L_DU_OUTPUT_DPAD0, + }, + }, +}; + static const struct rzg2l_du_device_info rzg2l_du_r9a07g044_info = { .channels_mask = BIT(0), .routes = { [RZG2L_DU_OUTPUT_DSI0] = { .possible_outputs = BIT(0), - .port = 0, + .du_output = RZG2L_DU_OUTPUT_DSI0, }, [RZG2L_DU_OUTPUT_DPAD0] = { .possible_outputs = BIT(0), - .port = 1, + .du_output = RZG2L_DU_OUTPUT_DPAD0, } } }; static const struct of_device_id rzg2l_du_of_table[] = { + { .compatible = "renesas,r9a07g043u-du", .data = &rzg2l_du_r9a07g043u_info }, { .compatible = "renesas,r9a07g044-du", .data = &rzg2l_du_r9a07g044_info }, { /* sentinel */ } }; diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h index 58806c2a8f2b..ab82b5c86d6e 100644 --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h @@ -29,7 +29,7 @@ enum rzg2l_du_output { /* * struct rzg2l_du_output_routing - Output routing specification * @possible_outputs: bitmask of possible outputs - * @port: device tree port number corresponding to this output route + * @du_output: DU output * * The DU has 2 possible outputs (DPAD0, DSI0). Output routing data * specify the valid SoC outputs, which CRTC can drive the output, and the type @@ -37,7 +37,7 @@ enum rzg2l_du_output { */ struct rzg2l_du_output_routing { unsigned int possible_outputs; - unsigned int port; + unsigned int du_output; }; /* @@ -53,6 +53,7 @@ struct rzg2l_du_device_info { #define RZG2L_DU_MAX_CRTCS 1 #define RZG2L_DU_MAX_VSPS 1 #define RZG2L_DU_MAX_DSI 1 +#define RZG2L_DU_OUTPUT_INVALID -1 struct rzg2l_du_device { struct device *dev; diff --git a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c index 07b312b6f81e..361350f2999e 100644 --- a/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c +++ b/drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c @@ -183,8 +183,8 @@ static int rzg2l_du_encoders_init(struct rzg2l_du_device *rcdu) /* Find the output route corresponding to the port number. */ for (i = 0; i < RZG2L_DU_OUTPUT_MAX; ++i) { - if (rcdu->info->routes[i].port == ep.port) { - output = i; + if (i == rcdu->info->routes[i].du_output) { + output = rcdu->info->routes[i].du_output; break; } }
The LCD controller is composed of Frame Compression Processor (FCPVD), Video Signal Processor (VSPD), and Display Unit (DU). It has DPI interface and supports a maximum resolution of WXGA along with 2 RPFs to support the blending of two picture layers and raster operations (ROPs). The DU module is connected to VSPD. Add RZ/G2UL DU support. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> --- v2->v3: * Avoided the line break in rzg2l_du_start_stop() for rstate. * Replaced port->du_output in struct rzg2l_du_output_routing and dropped using the port number to indicate the output type in rzg2l_du_encoders_init(). * Updated rzg2l_du_r9a07g043u_info and rzg2l_du_r9a07g044_info v1->v2: * No change. --- drivers/gpu/drm/renesas/rz-du/rzg2l_du_crtc.c | 8 +++++++- drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.c | 18 ++++++++++++++++-- drivers/gpu/drm/renesas/rz-du/rzg2l_du_drv.h | 5 +++-- drivers/gpu/drm/renesas/rz-du/rzg2l_du_kms.c | 4 ++-- 4 files changed, 28 insertions(+), 7 deletions(-)