| Message ID | a3fde99c2e522ef1fbf4e4bb125bc1d97a715eaf.1724159867.git.andrea.porta@suse.com (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
| Series | Add support for RaspberryPi RP1 PCI device using a DT overlay | expand |
On Tue, Aug 20, 2024 at 04:36:13PM +0200, Andrea della Porta wrote: > RaspberryPi RP1 is multi function PCI endpoint device that > exposes several subperipherals via PCI BAR. > Add an ethernet node for Cadence MACB to the RP1 dtso > > Signed-off-by: Andrea della Porta <andrea.porta@suse.com> > --- > arch/arm64/boot/dts/broadcom/rp1.dtso | 23 +++++++++++++++++++++++ > 1 file changed, 23 insertions(+) > > diff --git a/arch/arm64/boot/dts/broadcom/rp1.dtso b/arch/arm64/boot/dts/broadcom/rp1.dtso > index d80178a278ee..b40e203c28d5 100644 > --- a/arch/arm64/boot/dts/broadcom/rp1.dtso > +++ b/arch/arm64/boot/dts/broadcom/rp1.dtso > @@ -78,6 +78,29 @@ rp1_clocks: clocks@c040018000 { > <50000000>; // RP1_CLK_ETH_TSU > }; > > + rp1_eth: ethernet@c040100000 { > + reg = <0xc0 0x40100000 0x0 0x4000>; > + compatible = "cdns,macb"; Please start using DTS coding style... Best regards, Krzysztof
On 8/20/24 07:36, Andrea della Porta wrote: > RaspberryPi RP1 is multi function PCI endpoint device that > exposes several subperipherals via PCI BAR. > Add an ethernet node for Cadence MACB to the RP1 dtso > > Signed-off-by: Andrea della Porta <andrea.porta@suse.com> > --- > arch/arm64/boot/dts/broadcom/rp1.dtso | 23 +++++++++++++++++++++++ > 1 file changed, 23 insertions(+) > > diff --git a/arch/arm64/boot/dts/broadcom/rp1.dtso b/arch/arm64/boot/dts/broadcom/rp1.dtso > index d80178a278ee..b40e203c28d5 100644 > --- a/arch/arm64/boot/dts/broadcom/rp1.dtso > +++ b/arch/arm64/boot/dts/broadcom/rp1.dtso > @@ -78,6 +78,29 @@ rp1_clocks: clocks@c040018000 { > <50000000>; // RP1_CLK_ETH_TSU > }; > > + rp1_eth: ethernet@c040100000 { > + reg = <0xc0 0x40100000 0x0 0x4000>; > + compatible = "cdns,macb"; > + #address-cells = <1>; > + #size-cells = <0>; > + interrupts = <RP1_INT_ETH IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&macb_pclk &macb_hclk &rp1_clocks RP1_CLK_ETH_TSU>; > + clock-names = "pclk", "hclk", "tsu_clk"; > + phy-mode = "rgmii-id"; > + cdns,aw2w-max-pipe = /bits/ 8 <8>; > + cdns,ar2r-max-pipe = /bits/ 8 <8>; > + cdns,use-aw2b-fill; > + local-mac-address = [00 00 00 00 00 00]; > + phy-handle = <&phy1>; > + phy-reset-gpios = <&rp1_gpio 32 GPIO_ACTIVE_LOW>; > + phy-reset-duration = <5>; > + > + phy1: ethernet-phy@1 { > + reg = <0x1>; > + brcm,powerdown-enable; Undocumented property, and I would like to understand why this needs to be specified in the Device Tree? What model of Broadcom Ethernet PHY is being used here?
Hi Florian, On 10:02 Wed 21 Aug , Florian Fainelli wrote: > On 8/20/24 07:36, Andrea della Porta wrote: > > RaspberryPi RP1 is multi function PCI endpoint device that > > exposes several subperipherals via PCI BAR. > > Add an ethernet node for Cadence MACB to the RP1 dtso > > > > Signed-off-by: Andrea della Porta <andrea.porta@suse.com> > > --- > > arch/arm64/boot/dts/broadcom/rp1.dtso | 23 +++++++++++++++++++++++ > > 1 file changed, 23 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/broadcom/rp1.dtso b/arch/arm64/boot/dts/broadcom/rp1.dtso > > index d80178a278ee..b40e203c28d5 100644 > > --- a/arch/arm64/boot/dts/broadcom/rp1.dtso > > +++ b/arch/arm64/boot/dts/broadcom/rp1.dtso > > @@ -78,6 +78,29 @@ rp1_clocks: clocks@c040018000 { > > <50000000>; // RP1_CLK_ETH_TSU > > }; > > + rp1_eth: ethernet@c040100000 { > > + reg = <0xc0 0x40100000 0x0 0x4000>; > > + compatible = "cdns,macb"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + interrupts = <RP1_INT_ETH IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&macb_pclk &macb_hclk &rp1_clocks RP1_CLK_ETH_TSU>; > > + clock-names = "pclk", "hclk", "tsu_clk"; > > + phy-mode = "rgmii-id"; > > + cdns,aw2w-max-pipe = /bits/ 8 <8>; > > + cdns,ar2r-max-pipe = /bits/ 8 <8>; > > + cdns,use-aw2b-fill; > > + local-mac-address = [00 00 00 00 00 00]; > > + phy-handle = <&phy1>; > > + phy-reset-gpios = <&rp1_gpio 32 GPIO_ACTIVE_LOW>; > > + phy-reset-duration = <5>; > > + > > + phy1: ethernet-phy@1 { > > + reg = <0x1>; > > + brcm,powerdown-enable; > > Undocumented property, and I would like to understand why this needs to be > specified in the Device Tree? What model of Broadcom Ethernet PHY is being > used here? It's a Broadcom BCM5421 transceiver, and that property is intended to support the optional link-down powersave from DT. It will require slight changes in drivers/net/phy/broadcom.c too and is not really necessary for minimal support, so I will drop it in the next iteration. Many thanks, Andrea > -- > Florian >
Hi Krzysztof, On 10:43 Wed 21 Aug , Krzysztof Kozlowski wrote: > On Tue, Aug 20, 2024 at 04:36:13PM +0200, Andrea della Porta wrote: > > RaspberryPi RP1 is multi function PCI endpoint device that > > exposes several subperipherals via PCI BAR. > > Add an ethernet node for Cadence MACB to the RP1 dtso > > > > Signed-off-by: Andrea della Porta <andrea.porta@suse.com> > > --- > > arch/arm64/boot/dts/broadcom/rp1.dtso | 23 +++++++++++++++++++++++ > > 1 file changed, 23 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/broadcom/rp1.dtso b/arch/arm64/boot/dts/broadcom/rp1.dtso > > index d80178a278ee..b40e203c28d5 100644 > > --- a/arch/arm64/boot/dts/broadcom/rp1.dtso > > +++ b/arch/arm64/boot/dts/broadcom/rp1.dtso > > @@ -78,6 +78,29 @@ rp1_clocks: clocks@c040018000 { > > <50000000>; // RP1_CLK_ETH_TSU > > }; > > > > + rp1_eth: ethernet@c040100000 { > > + reg = <0xc0 0x40100000 0x0 0x4000>; > > + compatible = "cdns,macb"; > > Please start using DTS coding style... Ack. Regards, Andrea > > Best regards, > Krzysztof >
diff --git a/arch/arm64/boot/dts/broadcom/rp1.dtso b/arch/arm64/boot/dts/broadcom/rp1.dtso index d80178a278ee..b40e203c28d5 100644 --- a/arch/arm64/boot/dts/broadcom/rp1.dtso +++ b/arch/arm64/boot/dts/broadcom/rp1.dtso @@ -78,6 +78,29 @@ rp1_clocks: clocks@c040018000 { <50000000>; // RP1_CLK_ETH_TSU }; + rp1_eth: ethernet@c040100000 { + reg = <0xc0 0x40100000 0x0 0x4000>; + compatible = "cdns,macb"; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <RP1_INT_ETH IRQ_TYPE_LEVEL_HIGH>; + clocks = <&macb_pclk &macb_hclk &rp1_clocks RP1_CLK_ETH_TSU>; + clock-names = "pclk", "hclk", "tsu_clk"; + phy-mode = "rgmii-id"; + cdns,aw2w-max-pipe = /bits/ 8 <8>; + cdns,ar2r-max-pipe = /bits/ 8 <8>; + cdns,use-aw2b-fill; + local-mac-address = [00 00 00 00 00 00]; + phy-handle = <&phy1>; + phy-reset-gpios = <&rp1_gpio 32 GPIO_ACTIVE_LOW>; + phy-reset-duration = <5>; + + phy1: ethernet-phy@1 { + reg = <0x1>; + brcm,powerdown-enable; + }; + }; + rp1_gpio: pinctrl@c0400d0000 { reg = <0xc0 0x400d0000 0x0 0xc000>, <0xc0 0x400e0000 0x0 0xc000>,
RaspberryPi RP1 is multi function PCI endpoint device that exposes several subperipherals via PCI BAR. Add an ethernet node for Cadence MACB to the RP1 dtso Signed-off-by: Andrea della Porta <andrea.porta@suse.com> --- arch/arm64/boot/dts/broadcom/rp1.dtso | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)