| Message ID | 20240827084815.1931169-1-ciprianmarian.costea@oss.nxp.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: dts: s32g: Add S32G2/S32G3 uSDHC pinmux | expand |
On Tue, 27 Aug 2024 11:48:15 +0300, Ciprian Costea wrote: > From: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> > > Adding 100mhz & 200mhz pinmux support for uSDHC helps to support > higher speed modes for SD (SDR50, DDR50, SDR104) and > eMMC (such as HS200, HS400/HS400ES). > > Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> > --- > arch/arm64/boot/dts/freescale/s32g2.dtsi | 153 ++++++++++++++++++ > .../arm64/boot/dts/freescale/s32g274a-evb.dts | 4 + > .../boot/dts/freescale/s32g274a-rdb2.dts | 4 + > arch/arm64/boot/dts/freescale/s32g3.dtsi | 153 ++++++++++++++++++ > .../boot/dts/freescale/s32g399a-rdb3.dts | 4 + > 5 files changed, 318 insertions(+) > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade New warnings running 'make CHECK_DTBS=y freescale/s32g274a-evb.dtb freescale/s32g274a-rdb2.dtb freescale/s32g399a-rdb3.dtb' for 20240827084815.1931169-1-ciprianmarian.costea@oss.nxp.com: arch/arm64/boot/dts/freescale/s32g274a-rdb2.dtb: pinctrl@4009c240: 'usdhc0-100mhzgrp', 'usdhc0-200mhzgrp', 'usdhc0grp' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/pinctrl/nxp,s32g2-siul2-pinctrl.yaml# arch/arm64/boot/dts/freescale/s32g274a-evb.dtb: pinctrl@4009c240: 'usdhc0-100mhzgrp', 'usdhc0-200mhzgrp', 'usdhc0grp' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/pinctrl/nxp,s32g2-siul2-pinctrl.yaml# arch/arm64/boot/dts/freescale/s32g399a-rdb3.dtb: pinctrl@4009c240: 'usdhc0-100mhzgrp', 'usdhc0-200mhzgrp', 'usdhc0grp' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/pinctrl/nxp,s32g2-siul2-pinctrl.yaml#
On 8/27/2024 3:31 PM, Rob Herring (Arm) wrote: > > On Tue, 27 Aug 2024 11:48:15 +0300, Ciprian Costea wrote: >> From: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> >> >> Adding 100mhz & 200mhz pinmux support for uSDHC helps to support >> higher speed modes for SD (SDR50, DDR50, SDR104) and >> eMMC (such as HS200, HS400/HS400ES). >> >> Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> >> --- >> arch/arm64/boot/dts/freescale/s32g2.dtsi | 153 ++++++++++++++++++ >> .../arm64/boot/dts/freescale/s32g274a-evb.dts | 4 + >> .../boot/dts/freescale/s32g274a-rdb2.dts | 4 + >> arch/arm64/boot/dts/freescale/s32g3.dtsi | 153 ++++++++++++++++++ >> .../boot/dts/freescale/s32g399a-rdb3.dts | 4 + >> 5 files changed, 318 insertions(+) >> > > > My bot found new DTB warnings on the .dts files added or changed in this > series. > > Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings > are fixed by another series. Ultimately, it is up to the platform > maintainer whether these warnings are acceptable or not. No need to reply > unless the platform maintainer has comments. > > If you already ran DT checks and didn't see these error(s), then > make sure dt-schema is up to date: > > pip3 install dtschema --upgrade > > > New warnings running 'make CHECK_DTBS=y freescale/s32g274a-evb.dtb freescale/s32g274a-rdb2.dtb freescale/s32g399a-rdb3.dtb' for 20240827084815.1931169-1-ciprianmarian.costea@oss.nxp.com: > > arch/arm64/boot/dts/freescale/s32g274a-rdb2.dtb: pinctrl@4009c240: 'usdhc0-100mhzgrp', 'usdhc0-200mhzgrp', 'usdhc0grp' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+' > from schema $id: http://devicetree.org/schemas/pinctrl/nxp,s32g2-siul2-pinctrl.yaml# > arch/arm64/boot/dts/freescale/s32g274a-evb.dtb: pinctrl@4009c240: 'usdhc0-100mhzgrp', 'usdhc0-200mhzgrp', 'usdhc0grp' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+' > from schema $id: http://devicetree.org/schemas/pinctrl/nxp,s32g2-siul2-pinctrl.yaml# > arch/arm64/boot/dts/freescale/s32g399a-rdb3.dtb: pinctrl@4009c240: 'usdhc0-100mhzgrp', 'usdhc0-200mhzgrp', 'usdhc0grp' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+' > from schema $id: http://devicetree.org/schemas/pinctrl/nxp,s32g2-siul2-pinctrl.yaml# > > > > > Hello Rob, Thanks for pointing out these warnings. I will fix them in V2. Best Regards, Ciprian Costea
diff --git a/arch/arm64/boot/dts/freescale/s32g2.dtsi b/arch/arm64/boot/dts/freescale/s32g2.dtsi index fa054bfe7d5c..303be64399b5 100644 --- a/arch/arm64/boot/dts/freescale/s32g2.dtsi +++ b/arch/arm64/boot/dts/freescale/s32g2.dtsi @@ -162,6 +162,159 @@ jtag-grp4 { slew-rate = <166>; }; }; + + pinctrl_usdhc0: usdhc0grp { + usdhc0-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <150>; + }; + + usdhc0-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <150>; + }; + + usdhc0-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <150>; + }; + + usdhc0-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <150>; + }; + + usdhc0-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; + + pinctrl_usdhc0_100mhz: usdhc0-100mhzgrp { + usdhc0-100mhz-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; + + pinctrl_usdhc0_200mhz: usdhc0-200mhzgrp { + usdhc0-200mhz-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; }; uart0: serial@401c8000 { diff --git a/arch/arm64/boot/dts/freescale/s32g274a-evb.dts b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts index dbe498798bd9..7ab917f547ef 100644 --- a/arch/arm64/boot/dts/freescale/s32g274a-evb.dts +++ b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts @@ -34,6 +34,10 @@ &uart0 { }; &usdhc0 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc0>; + pinctrl-1 = <&pinctrl_usdhc0_100mhz>; + pinctrl-2 = <&pinctrl_usdhc0_200mhz>; disable-wp; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts index ab1e5caaeae7..8739f63771bc 100644 --- a/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts +++ b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts @@ -40,6 +40,10 @@ &uart1 { }; &usdhc0 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc0>; + pinctrl-1 = <&pinctrl_usdhc0_100mhz>; + pinctrl-2 = <&pinctrl_usdhc0_200mhz>; disable-wp; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/s32g3.dtsi b/arch/arm64/boot/dts/freescale/s32g3.dtsi index b4226a9143c8..0d6f077b1eb9 100644 --- a/arch/arm64/boot/dts/freescale/s32g3.dtsi +++ b/arch/arm64/boot/dts/freescale/s32g3.dtsi @@ -219,6 +219,159 @@ jtag-grp4 { slew-rate = <166>; }; }; + + pinctrl_usdhc0: usdhc0grp { + usdhc0-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <150>; + }; + + usdhc0-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <150>; + }; + + usdhc0-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <150>; + }; + + usdhc0-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <150>; + }; + + usdhc0-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; + + pinctrl_usdhc0_100mhz: usdhc0-100mhzgrp { + usdhc0-100mhz-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; + + pinctrl_usdhc0_200mhz: usdhc0-200mhzgrp { + usdhc0-200mhz-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; }; uart0: serial@401c8000 { diff --git a/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts b/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts index 176e5af191c8..828e353455b5 100644 --- a/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts +++ b/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts @@ -40,6 +40,10 @@ &uart1 { }; &usdhc0 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc0>; + pinctrl-1 = <&pinctrl_usdhc0_100mhz>; + pinctrl-2 = <&pinctrl_usdhc0_200mhz>; bus-width = <8>; disable-wp; status = "okay";