Message ID | 20240805083636.1381205-1-marge.yang@tw.synaptics.com (mailing list archive) |
---|---|
State | Mainlined |
Commit | 14d650fcb7fb57f121fda361b9f63eeefd8d59a5 |
Headers | show |
Series | [V2] Input: synaptics-rmi4 - Supports to query DPM value. | expand |
On Mon, Aug 05, 2024 at 08:36:36AM +0000, Marge Yang wrote: > Newer firmware allows to query touchpad resolution > information by reading from resolution register. > Presence of resolution register is signalled via bit > 29 of the "register presence" register. > On devices that lack this resolution register > we fall back to using pitch and number of receivers > data to calculate size of the sensor. > > RMI4 F12 will support to query DPM value on Touchpad. > When TP firmware doesn't support to report logical and > physical value within the Touchpad's HID report. > We can directly query the DPM value through RMI. > > Signed-off-by: Marge Yang <marge.yang@tw.synaptics.com> > Signed-off-by: Vincent Huang <Vincent.Huang@tw.synaptics.com> Applied, thank you.
Thanks Dmitry. Regards, Derek Synaptics -----Original Message----- From: Dmitry Torokhov <dmitry.torokhov@gmail.com> Sent: Tuesday, August 6, 2024 1:32 AM To: Marge Yang <Marge.Yang@tw.synaptics.com> Cc: linux-input@vger.kernel.org; linux-kernel@vger.kernel.org; Vincent Huang <Vincent.huang@tw.synaptics.com>; David Chiu <David.Chiu@tw.synaptics.com>; Derek Cheng <derek.cheng@tw.synaptics.com>; Sam Tsai <Sam.Tsai@synaptics.com> Subject: Re: [PATCH V2] Input: synaptics-rmi4 - Supports to query DPM value. CAUTION: Email originated externally, do not click links or open attachments unless you recognize the sender and know the content is safe. On Mon, Aug 05, 2024 at 08:36:36AM +0000, Marge Yang wrote: > Newer firmware allows to query touchpad resolution information by > reading from resolution register. > Presence of resolution register is signalled via bit > 29 of the "register presence" register. > On devices that lack this resolution register we fall back to using > pitch and number of receivers data to calculate size of the sensor. > > RMI4 F12 will support to query DPM value on Touchpad. > When TP firmware doesn't support to report logical and physical value > within the Touchpad's HID report. > We can directly query the DPM value through RMI. > > Signed-off-by: Marge Yang <marge.yang@tw.synaptics.com> > Signed-off-by: Vincent Huang <Vincent.Huang@tw.synaptics.com> Applied, thank you. -- Dmitry
Hi, On Mon, Aug 05, 2024 at 08:36:36AM +0000, Marge Yang wrote: > Newer firmware allows to query touchpad resolution > information by reading from resolution register. > Presence of resolution register is signalled via bit > 29 of the "register presence" register. > On devices that lack this resolution register > we fall back to using pitch and number of receivers > data to calculate size of the sensor. > > RMI4 F12 will support to query DPM value on Touchpad. > When TP firmware doesn't support to report logical and > physical value within the Touchpad's HID report. > We can directly query the DPM value through RMI. > > Signed-off-by: Marge Yang <marge.yang@tw.synaptics.com> > Signed-off-by: Vincent Huang <Vincent.Huang@tw.synaptics.com> > --- > drivers/input/rmi4/rmi_f12.c | 41 +++++++++++++++++++++++++++--------- > 1 file changed, 31 insertions(+), 10 deletions(-) > > diff --git a/drivers/input/rmi4/rmi_f12.c b/drivers/input/rmi4/rmi_f12.c > index 7e97944f7616..b8dfb9ffdbf5 100644 > --- a/drivers/input/rmi4/rmi_f12.c > +++ b/drivers/input/rmi4/rmi_f12.c > @@ -24,6 +24,7 @@ enum rmi_f12_object_type { > }; > > #define F12_DATA1_BYTES_PER_OBJ 8 > +#define RMI_F12_QUERY_RESOLUTION 29 > > struct f12_data { > struct rmi_2d_sensor sensor; > @@ -73,6 +74,8 @@ static int rmi_f12_read_sensor_tuning(struct f12_data *f12) > int pitch_y = 0; > int rx_receivers = 0; > int tx_receivers = 0; > + u16 query_dpm_addr = 0; > + int dpm_resolution = 0; > > item = rmi_get_register_desc_item(&f12->control_reg_desc, 8); > if (!item) { > @@ -122,18 +125,36 @@ static int rmi_f12_read_sensor_tuning(struct f12_data *f12) > offset += 4; > } > > - if (rmi_register_desc_has_subpacket(item, 3)) { > - rx_receivers = buf[offset]; > - tx_receivers = buf[offset + 1]; > - offset += 2; > - } > + /* Use the Query DPM feature when the query register exists for resolution. */ > + item = rmi_get_register_desc_item(&f12->query_reg_desc, RMI_F12_QUERY_RESOLUTION); > + if (item) { > + offset = rmi_register_desc_calc_reg_offset(&f12->query_reg_desc, > + RMI_F12_QUERY_RESOLUTION); > + query_dpm_addr = fn->fd.query_base_addr + offset; > + ret = rmi_read(fn->rmi_dev, query_dpm_addr, buf); > + if (ret < 0) { > + dev_err(&fn->dev, "Failed to read DPM value: %d\n", ret); > + return -ENODEV; > + } > + dpm_resolution = buf[0]; > + > + sensor->x_mm = sensor->max_x / dpm_resolution; > + sensor->y_mm = sensor->max_y / dpm_resolution; > + } else { > + if (rmi_register_desc_has_subpacket(item, 3)) { The item variable is NULL in this branch, as it was overwritten just before the if statement. This patch causes a NULL pointer dereference: [ 1.738650] rmi4_f01 rmi4-00.fn01: found RMI device, manufacturer: Synaptics, product: S3706B, fw id: 2869618 [ 1.771232] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000018 [ 1.771245] Mem abort info: [ 1.771248] ESR = 0x0000000096000004 [ 1.771254] EC = 0x25: DABT (current EL), IL = 32 bits [ 1.771261] SET = 0, FnV = 0 [ 1.771266] EA = 0, S1PTW = 0 [ 1.771271] FSC = 0x04: level 0 translation fault [ 1.771276] Data abort info: [ 1.771280] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 1.771285] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 1.771291] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 1.771298] user pgtable: 4k pages, 48-bit VAs, pgdp=00000000986a9000 [ 1.771308] [0000000000000018] pgd=0000000000000000, p4d=0000000000000000 [ 1.771326] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [ 1.771335] Modules linked in: rmi_i2c(+) rmi_core gpi [ 1.771358] CPU: 1 UID: 0 PID: 165 Comm: udevd Not tainted 6.11.0-rc6-next-20240902-sdm670-00022-g6ab596a153e1-dirty #10 [ 1.771371] Hardware name: Google Inc. MSM sdm670 S4 PVT v1.0 (DT) [ 1.771378] pstate: 20400005 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 1.771389] pc : _find_next_bit+0x18/0x78 [ 1.771411] lr : rmi_register_desc_has_subpacket+0x24/0x40 [rmi_core] [ 1.771444] sp : ffff800080fdb0b0 [ 1.771448] x29: ffff800080fdb0b0 x28: 0000000000000000 x27: 000000000000000c [ 1.771463] x26: ffff614ec34aa880 x25: ffff800080fdb0f9 x24: ffff614ec34aa958 [ 1.771477] x23: ffff614ec34adc00 x22: ffff614ed8a02880 x21: ffff614ec34aa9c8 [ 1.771492] x20: ffff614ec34adc18 x19: 0000000000000003 x18: 000000005e77a5e3 [ 1.771506] x17: 000000040044ffff x16: ffffb02de6d83ba8 x15: 0000000000000000 [ 1.771520] x14: ffff614ec1a85640 x13: ffff614ec96dc580 x12: 000000003474591d [ 1.771534] x11: 0000000068d948e4 x10: ffffb02d74a1c000 x9 : 0000000000000000 [ 1.771548] x8 : ffff614ec96dc500 x7 : 0000000000000001 x6 : 0000000000000001 [ 1.771561] x5 : 0000000000000000 x4 : fffffffffffffff8 x3 : 0000000000000000 [ 1.771574] x2 : 0000000000000003 x1 : 0000000000000100 x0 : 0000000000000018 [ 1.771588] Call trace: [ 1.771593] _find_next_bit+0x18/0x78 [ 1.771608] rmi_f12_probe+0x728/0x960 [rmi_core] [ 1.771632] rmi_function_probe+0x8c/0x20c [rmi_core] [ 1.771654] really_probe+0xbc/0x2c0 [ 1.771671] __driver_probe_device+0x78/0x120 [ 1.771686] driver_probe_device+0x3c/0x154 [ 1.771699] __device_attach_driver+0xb8/0x140 [ 1.771713] bus_for_each_drv+0x88/0xe8 [ 1.771727] __device_attach+0xa0/0x190 [ 1.771735] device_initial_probe+0x14/0x20 [ 1.771744] bus_probe_device+0xb4/0xc0 [ 1.771757] device_add+0x578/0x750 [ 1.771769] rmi_register_function+0x64/0xc8 [rmi_core] [ 1.771792] rmi_create_function+0x11c/0x1c4 [rmi_core] [ 1.771815] rmi_scan_pdt+0x90/0x1e4 [rmi_core] [ 1.771837] rmi_init_functions+0x6c/0x13c [rmi_core] [ 1.771860] rmi_driver_probe+0x130/0x3a0 [rmi_core] [ 1.771882] really_probe+0xbc/0x2c0 [ 1.771896] __driver_probe_device+0x78/0x120 [ 1.771911] driver_probe_device+0x3c/0x154 [ 1.771925] __device_attach_driver+0xb8/0x140 [ 1.771939] bus_for_each_drv+0x88/0xe8 [ 1.771952] __device_attach+0xa0/0x190 [ 1.771960] device_initial_probe+0x14/0x20 [ 1.771970] bus_probe_device+0xb4/0xc0 [ 1.771983] device_add+0x578/0x750 [ 1.771994] rmi_register_transport_device+0x8c/0x138 [rmi_core] [ 1.772017] rmi_i2c_probe+0x1b0/0x304 [rmi_i2c] [ 1.772040] i2c_device_probe+0x130/0x290 [ 1.772056] really_probe+0xbc/0x2c0 [ 1.772070] __driver_probe_device+0x78/0x120 [ 1.772084] driver_probe_device+0x3c/0x154 [ 1.772098] __driver_attach+0x90/0x1a0 [ 1.772111] bus_for_each_dev+0x7c/0xe0 [ 1.772124] driver_attach+0x24/0x30 [ 1.772137] bus_add_driver+0xe4/0x208 [ 1.772150] driver_register+0x68/0x124 [ 1.772159] i2c_register_driver+0x48/0xcc [ 1.772173] rmi_i2c_driver_init+0x20/0x1000 [rmi_i2c] [ 1.772185] do_one_initcall+0x60/0x1d4 [ 1.772198] do_init_module+0x5c/0x21c [ 1.772211] load_module+0x18cc/0x1e60 [ 1.772222] init_module_from_file+0x88/0xd0 [ 1.772234] __arm64_sys_finit_module+0x1c0/0x320 [ 1.772246] invoke_syscall+0x48/0x104 [ 1.772261] el0_svc_common.constprop.0+0x40/0xe0 [ 1.772274] do_el0_svc+0x1c/0x28 [ 1.772287] el0_svc+0x34/0xe0 [ 1.772298] el0t_64_sync_handler+0x120/0x12c [ 1.772309] el0t_64_sync+0x190/0x194 [ 1.772324] Code: d346fc43 92800004 9ac22084 d37df065 (f8656802) [ 1.772331] ---[ end trace 0000000000000000 ]---
On Tue, Sep 03, 2024 at 02:07:23PM -0400, Richard Acayan wrote: > > + /* Use the Query DPM feature when the query register exists for resolution. */ > > + item = rmi_get_register_desc_item(&f12->query_reg_desc, RMI_F12_QUERY_RESOLUTION); > > + if (item) { > > + offset = rmi_register_desc_calc_reg_offset(&f12->query_reg_desc, > > + RMI_F12_QUERY_RESOLUTION); > > + query_dpm_addr = fn->fd.query_base_addr + offset; > > + ret = rmi_read(fn->rmi_dev, query_dpm_addr, buf); > > + if (ret < 0) { > > + dev_err(&fn->dev, "Failed to read DPM value: %d\n", ret); > > + return -ENODEV; > > + } > > + dpm_resolution = buf[0]; > > + > > + sensor->x_mm = sensor->max_x / dpm_resolution; > > + sensor->y_mm = sensor->max_y / dpm_resolution; > > + } else { > > + if (rmi_register_desc_has_subpacket(item, 3)) { > > The item variable is NULL in this branch, as it was overwritten just > before the if statement. > > This patch causes a NULL pointer dereference: Ugh, indeed. I guess the simplest way of fixing this would be: diff --git a/drivers/input/rmi4/rmi_f12.c b/drivers/input/rmi4/rmi_f12.c index fc2cc8e2b0ba..8246fe77114b 100644 --- a/drivers/input/rmi4/rmi_f12.c +++ b/drivers/input/rmi4/rmi_f12.c @@ -129,9 +129,8 @@ static int rmi_f12_read_sensor_tuning(struct f12_data *f12) * Use the Query DPM feature when the resolution query register * exists. */ - item = rmi_get_register_desc_item(&f12->query_reg_desc, - RMI_F12_QUERY_RESOLUTION); - if (item) { + if (rmi_get_register_desc_item(&f12->query_reg_desc, + RMI_F12_QUERY_RESOLUTION)) { offset = rmi_register_desc_calc_reg_offset(&f12->query_reg_desc, RMI_F12_QUERY_RESOLUTION); query_dpm_addr = fn->fd.query_base_addr + offset; Could you please tell me if this works for you? Thanks.
On Tue, Sep 03, 2024 at 11:40:38AM -0700, Dmitry Torokhov wrote: > On Tue, Sep 03, 2024 at 02:07:23PM -0400, Richard Acayan wrote: > > > + /* Use the Query DPM feature when the query register exists for resolution. */ > > > + item = rmi_get_register_desc_item(&f12->query_reg_desc, RMI_F12_QUERY_RESOLUTION); > > > + if (item) { > > > + offset = rmi_register_desc_calc_reg_offset(&f12->query_reg_desc, > > > + RMI_F12_QUERY_RESOLUTION); > > > + query_dpm_addr = fn->fd.query_base_addr + offset; > > > + ret = rmi_read(fn->rmi_dev, query_dpm_addr, buf); > > > + if (ret < 0) { > > > + dev_err(&fn->dev, "Failed to read DPM value: %d\n", ret); > > > + return -ENODEV; > > > + } > > > + dpm_resolution = buf[0]; > > > + > > > + sensor->x_mm = sensor->max_x / dpm_resolution; > > > + sensor->y_mm = sensor->max_y / dpm_resolution; > > > + } else { > > > + if (rmi_register_desc_has_subpacket(item, 3)) { > > > > The item variable is NULL in this branch, as it was overwritten just > > before the if statement. > > > > This patch causes a NULL pointer dereference: > > Ugh, indeed. I guess the simplest way of fixing this would be: > > diff --git a/drivers/input/rmi4/rmi_f12.c b/drivers/input/rmi4/rmi_f12.c > index fc2cc8e2b0ba..8246fe77114b 100644 > --- a/drivers/input/rmi4/rmi_f12.c > +++ b/drivers/input/rmi4/rmi_f12.c > @@ -129,9 +129,8 @@ static int rmi_f12_read_sensor_tuning(struct f12_data *f12) > * Use the Query DPM feature when the resolution query register > * exists. > */ > - item = rmi_get_register_desc_item(&f12->query_reg_desc, > - RMI_F12_QUERY_RESOLUTION); > - if (item) { > + if (rmi_get_register_desc_item(&f12->query_reg_desc, > + RMI_F12_QUERY_RESOLUTION)) { > offset = rmi_register_desc_calc_reg_offset(&f12->query_reg_desc, > RMI_F12_QUERY_RESOLUTION); > query_dpm_addr = fn->fd.query_base_addr + offset; > > Could you please tell me if this works for you? Yeah, it fixes the bug.
On Tue, Sep 03, 2024 at 05:33:23PM -0400, Richard Acayan wrote: > On Tue, Sep 03, 2024 at 11:40:38AM -0700, Dmitry Torokhov wrote: > > On Tue, Sep 03, 2024 at 02:07:23PM -0400, Richard Acayan wrote: > > > > + /* Use the Query DPM feature when the query register exists for resolution. */ > > > > + item = rmi_get_register_desc_item(&f12->query_reg_desc, RMI_F12_QUERY_RESOLUTION); > > > > + if (item) { > > > > + offset = rmi_register_desc_calc_reg_offset(&f12->query_reg_desc, > > > > + RMI_F12_QUERY_RESOLUTION); > > > > + query_dpm_addr = fn->fd.query_base_addr + offset; > > > > + ret = rmi_read(fn->rmi_dev, query_dpm_addr, buf); > > > > + if (ret < 0) { > > > > + dev_err(&fn->dev, "Failed to read DPM value: %d\n", ret); > > > > + return -ENODEV; > > > > + } > > > > + dpm_resolution = buf[0]; > > > > + > > > > + sensor->x_mm = sensor->max_x / dpm_resolution; > > > > + sensor->y_mm = sensor->max_y / dpm_resolution; > > > > + } else { > > > > + if (rmi_register_desc_has_subpacket(item, 3)) { > > > > > > The item variable is NULL in this branch, as it was overwritten just > > > before the if statement. > > > > > > This patch causes a NULL pointer dereference: > > > > Ugh, indeed. I guess the simplest way of fixing this would be: > > > > diff --git a/drivers/input/rmi4/rmi_f12.c b/drivers/input/rmi4/rmi_f12.c > > index fc2cc8e2b0ba..8246fe77114b 100644 > > --- a/drivers/input/rmi4/rmi_f12.c > > +++ b/drivers/input/rmi4/rmi_f12.c > > @@ -129,9 +129,8 @@ static int rmi_f12_read_sensor_tuning(struct f12_data *f12) > > * Use the Query DPM feature when the resolution query register > > * exists. > > */ > > - item = rmi_get_register_desc_item(&f12->query_reg_desc, > > - RMI_F12_QUERY_RESOLUTION); > > - if (item) { > > + if (rmi_get_register_desc_item(&f12->query_reg_desc, > > + RMI_F12_QUERY_RESOLUTION)) { > > offset = rmi_register_desc_calc_reg_offset(&f12->query_reg_desc, > > RMI_F12_QUERY_RESOLUTION); > > query_dpm_addr = fn->fd.query_base_addr + offset; > > > > Could you please tell me if this works for you? > > Yeah, it fixes the bug. Great, thank you for reporting and testing!
diff --git a/drivers/input/rmi4/rmi_f12.c b/drivers/input/rmi4/rmi_f12.c index 7e97944f7616..b8dfb9ffdbf5 100644 --- a/drivers/input/rmi4/rmi_f12.c +++ b/drivers/input/rmi4/rmi_f12.c @@ -24,6 +24,7 @@ enum rmi_f12_object_type { }; #define F12_DATA1_BYTES_PER_OBJ 8 +#define RMI_F12_QUERY_RESOLUTION 29 struct f12_data { struct rmi_2d_sensor sensor; @@ -73,6 +74,8 @@ static int rmi_f12_read_sensor_tuning(struct f12_data *f12) int pitch_y = 0; int rx_receivers = 0; int tx_receivers = 0; + u16 query_dpm_addr = 0; + int dpm_resolution = 0; item = rmi_get_register_desc_item(&f12->control_reg_desc, 8); if (!item) { @@ -122,18 +125,36 @@ static int rmi_f12_read_sensor_tuning(struct f12_data *f12) offset += 4; } - if (rmi_register_desc_has_subpacket(item, 3)) { - rx_receivers = buf[offset]; - tx_receivers = buf[offset + 1]; - offset += 2; - } + /* Use the Query DPM feature when the query register exists for resolution. */ + item = rmi_get_register_desc_item(&f12->query_reg_desc, RMI_F12_QUERY_RESOLUTION); + if (item) { + offset = rmi_register_desc_calc_reg_offset(&f12->query_reg_desc, + RMI_F12_QUERY_RESOLUTION); + query_dpm_addr = fn->fd.query_base_addr + offset; + ret = rmi_read(fn->rmi_dev, query_dpm_addr, buf); + if (ret < 0) { + dev_err(&fn->dev, "Failed to read DPM value: %d\n", ret); + return -ENODEV; + } + dpm_resolution = buf[0]; + + sensor->x_mm = sensor->max_x / dpm_resolution; + sensor->y_mm = sensor->max_y / dpm_resolution; + } else { + if (rmi_register_desc_has_subpacket(item, 3)) { + rx_receivers = buf[offset]; + tx_receivers = buf[offset + 1]; + offset += 2; + } - /* Skip over sensor flags */ - if (rmi_register_desc_has_subpacket(item, 4)) - offset += 1; + /* Skip over sensor flags */ + if (rmi_register_desc_has_subpacket(item, 4)) + offset += 1; + + sensor->x_mm = (pitch_x * rx_receivers) >> 12; + sensor->y_mm = (pitch_y * tx_receivers) >> 12; + } - sensor->x_mm = (pitch_x * rx_receivers) >> 12; - sensor->y_mm = (pitch_y * tx_receivers) >> 12; rmi_dbg(RMI_DEBUG_FN, &fn->dev, "%s: x_mm: %d y_mm: %d\n", __func__, sensor->x_mm, sensor->y_mm);