| Message ID | 20240913083724.1217691-6-quic_qianyu@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add support for PCIe3 on x1e80100 | expand |
On Fri, Sep 13, 2024 at 01:37:24AM GMT, Qiang Yu wrote: > Describe PCIe3 controller and PHY. Also add required system resources like > regulators, clocks, interrupts and registers configuration for PCIe3. > > Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com> > --- > arch/arm64/boot/dts/qcom/x1e80100.dtsi | 202 ++++++++++++++++++++++++- > 1 file changed, 201 insertions(+), 1 deletion(-) I didn't verify the addresses, the rest LGTM Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
On Fri, Sep 13, 2024 at 01:37:24AM -0700, Qiang Yu wrote: > Describe PCIe3 controller and PHY. Also add required system resources like > regulators, clocks, interrupts and registers configuration for PCIe3. > > Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com> > --- > arch/arm64/boot/dts/qcom/x1e80100.dtsi | 202 ++++++++++++++++++++++++- > 1 file changed, 201 insertions(+), 1 deletion(-) > > diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi > index a36076e3c56b..a7703e4974a6 100644 > --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi > +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi > @@ -744,7 +744,7 @@ gcc: clock-controller@100000 { > > clocks = <&bi_tcxo_div2>, > <&sleep_clk>, > - <0>, > + <&pcie3_phy>, > <&pcie4_phy>, > <&pcie5_phy>, > <&pcie6a_phy>, > @@ -2907,6 +2907,206 @@ mmss_noc: interconnect@1780000 { > #interconnect-cells = <2>; > }; > > + pcie3: pci@1bd0000 { pcie@ > + device_type = "pci"; > + compatible = "qcom,pcie-x1e80100"; > + reg = <0 0x01bd0000 0 0x3000>, > + <0 0x78000000 0 0xf1d>, 0x0 here and below. > + <0 0x78000f40 0 0xa8>, > + <0 0x78001000 0 0x1000>, > + <0 0x78100000 0 0x100000>, > + <0 0x01bd3000 0 0x1000>; > + reg-names = "parf", > + "dbi", > + "elbi", > + "atu", > + "config", > + "mhi"; > + #address-cells = <3>; > + #size-cells = <2>; > + ranges = <0x01000000 0x0 0x00000000 0x0 0x78200000 0x0 0x100000>, > + <0x02000000 0x0 0x78300000 0x0 0x78300000 0x0 0x3d00000>, > + <0x03000000 0x7 0x40000000 0x7 0x40000000 0x0 0x40000000>; > + bus-range = <0x00 0xff>; > + > + dma-coherent; > + > + linux,pci-domain = <3>; > + num-lanes = <8>; > + > + interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 769 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "msi0", > + "msi1", > + "msi2", > + "msi3", > + "msi4", > + "msi5", > + "msi6", > + "msi7"; Can you add 'global' interrupt as well? While doing so, please make sure the global_irq related patches are applied and Link up works fine. Those patches are already in linux-next. > + > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 0x7>; > + interrupt-map = <0 0 0 1 &intc 0 0 0 220 IRQ_TYPE_LEVEL_HIGH>, Use GIC_SPI for the parent interrupt specifier. - Mani > + <0 0 0 2 &intc 0 0 0 221 IRQ_TYPE_LEVEL_HIGH>, > + <0 0 0 3 &intc 0 0 0 237 IRQ_TYPE_LEVEL_HIGH>, > + <0 0 0 4 &intc 0 0 0 238 IRQ_TYPE_LEVEL_HIGH>; > + > + clocks = <&gcc GCC_PCIE_3_AUX_CLK>, > + <&gcc GCC_PCIE_3_CFG_AHB_CLK>, > + <&gcc GCC_PCIE_3_MSTR_AXI_CLK>, > + <&gcc GCC_PCIE_3_SLV_AXI_CLK>, > + <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>, > + <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>, > + <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>; > + clock-names = "aux", > + "cfg", > + "bus_master", > + "bus_slave", > + "slave_q2a", > + "noc_aggr", > + "cnoc_sf_axi"; > + > + assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>; > + assigned-clock-rates = <19200000>; > + > + interconnects = <&pcie_south_anoc MASTER_PCIE_3 QCOM_ICC_TAG_ALWAYS > + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, > + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS > + &cnoc_main SLAVE_PCIE_3 QCOM_ICC_TAG_ALWAYS>; > + interconnect-names = "pcie-mem", > + "cpu-pcie"; > + > + resets = <&gcc GCC_PCIE_3_BCR>, > + <&gcc GCC_PCIE_3_LINK_DOWN_BCR>; > + reset-names = "pci", > + "link_down"; > + > + power-domains = <&gcc GCC_PCIE_3_GDSC>; > + > + phys = <&pcie3_phy>; > + phy-names = "pciephy"; > + > + operating-points-v2 = <&pcie3_opp_table>; > + > + status = "disabled"; > + > + pcie3_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + /* GEN 1 x1 */ > + opp-2500000 { > + opp-hz = /bits/ 64 <2500000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + opp-peak-kBps = <250000 1>; > + }; > + > + /* GEN 1 x2 and GEN 2 x1 */ > + opp-5000000 { > + opp-hz = /bits/ 64 <5000000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + opp-peak-kBps = <500000 1>; > + }; > + > + /* GEN 1 x4 and GEN 2 x2 */ > + opp-10000000 { > + opp-hz = /bits/ 64 <10000000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + opp-peak-kBps = <1000000 1>; > + }; > + > + /* GEN 1 x8 and GEN 2 x4 */ > + opp-20000000 { > + opp-hz = /bits/ 64 <20000000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + opp-peak-kBps = <2000000 1>; > + }; > + > + /* GEN 2 x8 */ > + opp-40000000 { > + opp-hz = /bits/ 64 <40000000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + opp-peak-kBps = <4000000 1>; > + }; > + > + /* GEN 3 x1 */ > + opp-8000000 { > + opp-hz = /bits/ 64 <8000000>; > + required-opps = <&rpmhpd_opp_svs>; > + opp-peak-kBps = <984500 1>; > + }; > + > + /* GEN 3 x2 and GEN 4 x1 */ > + opp-16000000 { > + opp-hz = /bits/ 64 <16000000>; > + required-opps = <&rpmhpd_opp_svs>; > + opp-peak-kBps = <1969000 1>; > + }; > + > + /* GEN 3 x4 and GEN 4 x2 */ > + opp-32000000 { > + opp-hz = /bits/ 64 <32000000>; > + required-opps = <&rpmhpd_opp_svs>; > + opp-peak-kBps = <3938000 1>; > + }; > + > + /* GEN 3 x8 and GEN 4 x4 */ > + opp-64000000 { > + opp-hz = /bits/ 64 <64000000>; > + required-opps = <&rpmhpd_opp_svs>; > + opp-peak-kBps = <7876000 1>; > + }; > + > + /* GEN 4 x8 */ > + opp-128000000 { > + opp-hz = /bits/ 64 <128000000>; > + required-opps = <&rpmhpd_opp_svs>; > + opp-peak-kBps = <15753000 1>; > + }; > + }; > + }; > + > + pcie3_phy: phy@1be0000 { > + compatible = "qcom,x1e80100-qmp-gen4x8-pcie-phy"; > + reg = <0 0x01be0000 0 0x10000>; > + > + clocks = <&gcc GCC_PCIE_3_PHY_AUX_CLK>, > + <&gcc GCC_PCIE_3_CFG_AHB_CLK>, > + <&tcsr TCSR_PCIE_8L_CLKREF_EN>, > + <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>, > + <&gcc GCC_PCIE_3_PIPE_CLK>, > + <&gcc GCC_PCIE_3_PIPEDIV2_CLK>; > + clock-names = "aux", > + "cfg_ahb", > + "ref", > + "rchng", > + "pipe", > + "pipediv2"; > + > + resets = <&gcc GCC_PCIE_3_PHY_BCR>, > + <&gcc GCC_PCIE_3_NOCSR_COM_PHY_BCR>; > + reset-names = "phy", > + "phy_nocsr"; > + > + assigned-clocks = <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>; > + assigned-clock-rates = <100000000>; > + > + power-domains = <&gcc GCC_PCIE_3_PHY_GDSC>; > + > + #clock-cells = <0>; > + clock-output-names = "pcie3_pipe_clk"; > + > + #phy-cells = <0>; > + > + status = "disabled"; > + }; > + > pcie6a: pci@1bf8000 { > device_type = "pci"; > compatible = "qcom,pcie-x1e80100"; > -- > 2.34.1 >
On 9/13/2024 9:57 PM, Manivannan Sadhasivam wrote: > On Fri, Sep 13, 2024 at 01:37:24AM -0700, Qiang Yu wrote: >> Describe PCIe3 controller and PHY. Also add required system resources like >> regulators, clocks, interrupts and registers configuration for PCIe3. >> >> Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com> >> --- >> arch/arm64/boot/dts/qcom/x1e80100.dtsi | 202 ++++++++++++++++++++++++- >> 1 file changed, 201 insertions(+), 1 deletion(-) >> >> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi >> index a36076e3c56b..a7703e4974a6 100644 >> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi >> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi >> @@ -744,7 +744,7 @@ gcc: clock-controller@100000 { >> >> clocks = <&bi_tcxo_div2>, >> <&sleep_clk>, >> - <0>, >> + <&pcie3_phy>, >> <&pcie4_phy>, >> <&pcie5_phy>, >> <&pcie6a_phy>, >> @@ -2907,6 +2907,206 @@ mmss_noc: interconnect@1780000 { >> #interconnect-cells = <2>; >> }; >> >> + pcie3: pci@1bd0000 { > pcie@ > >> + device_type = "pci"; >> + compatible = "qcom,pcie-x1e80100"; >> + reg = <0 0x01bd0000 0 0x3000>, >> + <0 0x78000000 0 0xf1d>, > 0x0 here and below. > >> + <0 0x78000f40 0 0xa8>, >> + <0 0x78001000 0 0x1000>, >> + <0 0x78100000 0 0x100000>, >> + <0 0x01bd3000 0 0x1000>; >> + reg-names = "parf", >> + "dbi", >> + "elbi", >> + "atu", >> + "config", >> + "mhi"; >> + #address-cells = <3>; >> + #size-cells = <2>; >> + ranges = <0x01000000 0x0 0x00000000 0x0 0x78200000 0x0 0x100000>, >> + <0x02000000 0x0 0x78300000 0x0 0x78300000 0x0 0x3d00000>, >> + <0x03000000 0x7 0x40000000 0x7 0x40000000 0x0 0x40000000>; >> + bus-range = <0x00 0xff>; >> + >> + dma-coherent; >> + >> + linux,pci-domain = <3>; >> + num-lanes = <8>; >> + >> + interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 769 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names = "msi0", >> + "msi1", >> + "msi2", >> + "msi3", >> + "msi4", >> + "msi5", >> + "msi6", >> + "msi7"; > Can you add 'global' interrupt as well? While doing so, please make sure the > global_irq related patches are applied and Link up works fine. Those patches are > already in linux-next. Sure, let me add global interrupt and have a try. Will also update patch according to your other comments. Thanks, Qiang > >> + >> + #interrupt-cells = <1>; >> + interrupt-map-mask = <0 0 0 0x7>; >> + interrupt-map = <0 0 0 1 &intc 0 0 0 220 IRQ_TYPE_LEVEL_HIGH>, > Use GIC_SPI for the parent interrupt specifier. > > - Mani > >> + <0 0 0 2 &intc 0 0 0 221 IRQ_TYPE_LEVEL_HIGH>, >> + <0 0 0 3 &intc 0 0 0 237 IRQ_TYPE_LEVEL_HIGH>, >> + <0 0 0 4 &intc 0 0 0 238 IRQ_TYPE_LEVEL_HIGH>; >> + >> + clocks = <&gcc GCC_PCIE_3_AUX_CLK>, >> + <&gcc GCC_PCIE_3_CFG_AHB_CLK>, >> + <&gcc GCC_PCIE_3_MSTR_AXI_CLK>, >> + <&gcc GCC_PCIE_3_SLV_AXI_CLK>, >> + <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>, >> + <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>, >> + <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>; >> + clock-names = "aux", >> + "cfg", >> + "bus_master", >> + "bus_slave", >> + "slave_q2a", >> + "noc_aggr", >> + "cnoc_sf_axi"; >> + >> + assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>; >> + assigned-clock-rates = <19200000>; >> + >> + interconnects = <&pcie_south_anoc MASTER_PCIE_3 QCOM_ICC_TAG_ALWAYS >> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, >> + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS >> + &cnoc_main SLAVE_PCIE_3 QCOM_ICC_TAG_ALWAYS>; >> + interconnect-names = "pcie-mem", >> + "cpu-pcie"; >> + >> + resets = <&gcc GCC_PCIE_3_BCR>, >> + <&gcc GCC_PCIE_3_LINK_DOWN_BCR>; >> + reset-names = "pci", >> + "link_down"; >> + >> + power-domains = <&gcc GCC_PCIE_3_GDSC>; >> + >> + phys = <&pcie3_phy>; >> + phy-names = "pciephy"; >> + >> + operating-points-v2 = <&pcie3_opp_table>; >> + >> + status = "disabled"; >> + >> + pcie3_opp_table: opp-table { >> + compatible = "operating-points-v2"; >> + >> + /* GEN 1 x1 */ >> + opp-2500000 { >> + opp-hz = /bits/ 64 <2500000>; >> + required-opps = <&rpmhpd_opp_low_svs>; >> + opp-peak-kBps = <250000 1>; >> + }; >> + >> + /* GEN 1 x2 and GEN 2 x1 */ >> + opp-5000000 { >> + opp-hz = /bits/ 64 <5000000>; >> + required-opps = <&rpmhpd_opp_low_svs>; >> + opp-peak-kBps = <500000 1>; >> + }; >> + >> + /* GEN 1 x4 and GEN 2 x2 */ >> + opp-10000000 { >> + opp-hz = /bits/ 64 <10000000>; >> + required-opps = <&rpmhpd_opp_low_svs>; >> + opp-peak-kBps = <1000000 1>; >> + }; >> + >> + /* GEN 1 x8 and GEN 2 x4 */ >> + opp-20000000 { >> + opp-hz = /bits/ 64 <20000000>; >> + required-opps = <&rpmhpd_opp_low_svs>; >> + opp-peak-kBps = <2000000 1>; >> + }; >> + >> + /* GEN 2 x8 */ >> + opp-40000000 { >> + opp-hz = /bits/ 64 <40000000>; >> + required-opps = <&rpmhpd_opp_low_svs>; >> + opp-peak-kBps = <4000000 1>; >> + }; >> + >> + /* GEN 3 x1 */ >> + opp-8000000 { >> + opp-hz = /bits/ 64 <8000000>; >> + required-opps = <&rpmhpd_opp_svs>; >> + opp-peak-kBps = <984500 1>; >> + }; >> + >> + /* GEN 3 x2 and GEN 4 x1 */ >> + opp-16000000 { >> + opp-hz = /bits/ 64 <16000000>; >> + required-opps = <&rpmhpd_opp_svs>; >> + opp-peak-kBps = <1969000 1>; >> + }; >> + >> + /* GEN 3 x4 and GEN 4 x2 */ >> + opp-32000000 { >> + opp-hz = /bits/ 64 <32000000>; >> + required-opps = <&rpmhpd_opp_svs>; >> + opp-peak-kBps = <3938000 1>; >> + }; >> + >> + /* GEN 3 x8 and GEN 4 x4 */ >> + opp-64000000 { >> + opp-hz = /bits/ 64 <64000000>; >> + required-opps = <&rpmhpd_opp_svs>; >> + opp-peak-kBps = <7876000 1>; >> + }; >> + >> + /* GEN 4 x8 */ >> + opp-128000000 { >> + opp-hz = /bits/ 64 <128000000>; >> + required-opps = <&rpmhpd_opp_svs>; >> + opp-peak-kBps = <15753000 1>; >> + }; >> + }; >> + }; >> + >> + pcie3_phy: phy@1be0000 { >> + compatible = "qcom,x1e80100-qmp-gen4x8-pcie-phy"; >> + reg = <0 0x01be0000 0 0x10000>; >> + >> + clocks = <&gcc GCC_PCIE_3_PHY_AUX_CLK>, >> + <&gcc GCC_PCIE_3_CFG_AHB_CLK>, >> + <&tcsr TCSR_PCIE_8L_CLKREF_EN>, >> + <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>, >> + <&gcc GCC_PCIE_3_PIPE_CLK>, >> + <&gcc GCC_PCIE_3_PIPEDIV2_CLK>; >> + clock-names = "aux", >> + "cfg_ahb", >> + "ref", >> + "rchng", >> + "pipe", >> + "pipediv2"; >> + >> + resets = <&gcc GCC_PCIE_3_PHY_BCR>, >> + <&gcc GCC_PCIE_3_NOCSR_COM_PHY_BCR>; >> + reset-names = "phy", >> + "phy_nocsr"; >> + >> + assigned-clocks = <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>; >> + assigned-clock-rates = <100000000>; >> + >> + power-domains = <&gcc GCC_PCIE_3_PHY_GDSC>; >> + >> + #clock-cells = <0>; >> + clock-output-names = "pcie3_pipe_clk"; >> + >> + #phy-cells = <0>; >> + >> + status = "disabled"; >> + }; >> + >> pcie6a: pci@1bf8000 { >> device_type = "pci"; >> compatible = "qcom,pcie-x1e80100"; >> -- >> 2.34.1 >>
diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi index a36076e3c56b..a7703e4974a6 100644 --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi @@ -744,7 +744,7 @@ gcc: clock-controller@100000 { clocks = <&bi_tcxo_div2>, <&sleep_clk>, - <0>, + <&pcie3_phy>, <&pcie4_phy>, <&pcie5_phy>, <&pcie6a_phy>, @@ -2907,6 +2907,206 @@ mmss_noc: interconnect@1780000 { #interconnect-cells = <2>; }; + pcie3: pci@1bd0000 { + device_type = "pci"; + compatible = "qcom,pcie-x1e80100"; + reg = <0 0x01bd0000 0 0x3000>, + <0 0x78000000 0 0xf1d>, + <0 0x78000f40 0 0xa8>, + <0 0x78001000 0 0x1000>, + <0 0x78100000 0 0x100000>, + <0 0x01bd3000 0 0x1000>; + reg-names = "parf", + "dbi", + "elbi", + "atu", + "config", + "mhi"; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x01000000 0x0 0x00000000 0x0 0x78200000 0x0 0x100000>, + <0x02000000 0x0 0x78300000 0x0 0x78300000 0x0 0x3d00000>, + <0x03000000 0x7 0x40000000 0x7 0x40000000 0x0 0x40000000>; + bus-range = <0x00 0xff>; + + dma-coherent; + + linux,pci-domain = <3>; + num-lanes = <8>; + + interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 769 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi0", + "msi1", + "msi2", + "msi3", + "msi4", + "msi5", + "msi6", + "msi7"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 0 0 220 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc 0 0 0 221 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc 0 0 0 237 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc 0 0 0 238 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_PCIE_3_AUX_CLK>, + <&gcc GCC_PCIE_3_CFG_AHB_CLK>, + <&gcc GCC_PCIE_3_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_3_SLV_AXI_CLK>, + <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>, + <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>, + <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>; + clock-names = "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "noc_aggr", + "cnoc_sf_axi"; + + assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>; + assigned-clock-rates = <19200000>; + + interconnects = <&pcie_south_anoc MASTER_PCIE_3 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &cnoc_main SLAVE_PCIE_3 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "pcie-mem", + "cpu-pcie"; + + resets = <&gcc GCC_PCIE_3_BCR>, + <&gcc GCC_PCIE_3_LINK_DOWN_BCR>; + reset-names = "pci", + "link_down"; + + power-domains = <&gcc GCC_PCIE_3_GDSC>; + + phys = <&pcie3_phy>; + phy-names = "pciephy"; + + operating-points-v2 = <&pcie3_opp_table>; + + status = "disabled"; + + pcie3_opp_table: opp-table { + compatible = "operating-points-v2"; + + /* GEN 1 x1 */ + opp-2500000 { + opp-hz = /bits/ 64 <2500000>; + required-opps = <&rpmhpd_opp_low_svs>; + opp-peak-kBps = <250000 1>; + }; + + /* GEN 1 x2 and GEN 2 x1 */ + opp-5000000 { + opp-hz = /bits/ 64 <5000000>; + required-opps = <&rpmhpd_opp_low_svs>; + opp-peak-kBps = <500000 1>; + }; + + /* GEN 1 x4 and GEN 2 x2 */ + opp-10000000 { + opp-hz = /bits/ 64 <10000000>; + required-opps = <&rpmhpd_opp_low_svs>; + opp-peak-kBps = <1000000 1>; + }; + + /* GEN 1 x8 and GEN 2 x4 */ + opp-20000000 { + opp-hz = /bits/ 64 <20000000>; + required-opps = <&rpmhpd_opp_low_svs>; + opp-peak-kBps = <2000000 1>; + }; + + /* GEN 2 x8 */ + opp-40000000 { + opp-hz = /bits/ 64 <40000000>; + required-opps = <&rpmhpd_opp_low_svs>; + opp-peak-kBps = <4000000 1>; + }; + + /* GEN 3 x1 */ + opp-8000000 { + opp-hz = /bits/ 64 <8000000>; + required-opps = <&rpmhpd_opp_svs>; + opp-peak-kBps = <984500 1>; + }; + + /* GEN 3 x2 and GEN 4 x1 */ + opp-16000000 { + opp-hz = /bits/ 64 <16000000>; + required-opps = <&rpmhpd_opp_svs>; + opp-peak-kBps = <1969000 1>; + }; + + /* GEN 3 x4 and GEN 4 x2 */ + opp-32000000 { + opp-hz = /bits/ 64 <32000000>; + required-opps = <&rpmhpd_opp_svs>; + opp-peak-kBps = <3938000 1>; + }; + + /* GEN 3 x8 and GEN 4 x4 */ + opp-64000000 { + opp-hz = /bits/ 64 <64000000>; + required-opps = <&rpmhpd_opp_svs>; + opp-peak-kBps = <7876000 1>; + }; + + /* GEN 4 x8 */ + opp-128000000 { + opp-hz = /bits/ 64 <128000000>; + required-opps = <&rpmhpd_opp_svs>; + opp-peak-kBps = <15753000 1>; + }; + }; + }; + + pcie3_phy: phy@1be0000 { + compatible = "qcom,x1e80100-qmp-gen4x8-pcie-phy"; + reg = <0 0x01be0000 0 0x10000>; + + clocks = <&gcc GCC_PCIE_3_PHY_AUX_CLK>, + <&gcc GCC_PCIE_3_CFG_AHB_CLK>, + <&tcsr TCSR_PCIE_8L_CLKREF_EN>, + <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>, + <&gcc GCC_PCIE_3_PIPE_CLK>, + <&gcc GCC_PCIE_3_PIPEDIV2_CLK>; + clock-names = "aux", + "cfg_ahb", + "ref", + "rchng", + "pipe", + "pipediv2"; + + resets = <&gcc GCC_PCIE_3_PHY_BCR>, + <&gcc GCC_PCIE_3_NOCSR_COM_PHY_BCR>; + reset-names = "phy", + "phy_nocsr"; + + assigned-clocks = <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>; + assigned-clock-rates = <100000000>; + + power-domains = <&gcc GCC_PCIE_3_PHY_GDSC>; + + #clock-cells = <0>; + clock-output-names = "pcie3_pipe_clk"; + + #phy-cells = <0>; + + status = "disabled"; + }; + pcie6a: pci@1bf8000 { device_type = "pci"; compatible = "qcom,pcie-x1e80100";
Describe PCIe3 controller and PHY. Also add required system resources like regulators, clocks, interrupts and registers configuration for PCIe3. Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com> --- arch/arm64/boot/dts/qcom/x1e80100.dtsi | 202 ++++++++++++++++++++++++- 1 file changed, 201 insertions(+), 1 deletion(-)