| Message ID | 20240830113347.4048370-2-ciprianmarian.costea@oss.nxp.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | add S32G2/S32G3 uSDHC pinmux | expand |
On 30/08/2024 13:33, Ciprian Costea wrote: > From: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> > > Adding 100mhz & 200mhz pinmux support for uSDHC helps to enable > higher speed modes for SD (SDR50, DDR50, SDR104) and > eMMC (such as HS200, HS400/HS400ES). > > Signed-off-by: Radu Pirea <radu-nicolae.pirea@nxp.com> > Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> Reviewed-by: Matthias Brugger <mbrugger@suse.com> > --- > arch/arm64/boot/dts/freescale/s32g2.dtsi | 153 ++++++++++++++++++ > .../arm64/boot/dts/freescale/s32g274a-evb.dts | 4 + > .../boot/dts/freescale/s32g274a-rdb2.dts | 4 + > arch/arm64/boot/dts/freescale/s32g3.dtsi | 153 ++++++++++++++++++ > .../boot/dts/freescale/s32g399a-rdb3.dts | 4 + > 5 files changed, 318 insertions(+) > > diff --git a/arch/arm64/boot/dts/freescale/s32g2.dtsi b/arch/arm64/boot/dts/freescale/s32g2.dtsi > index fa054bfe7d5c..7be430b78c83 100644 > --- a/arch/arm64/boot/dts/freescale/s32g2.dtsi > +++ b/arch/arm64/boot/dts/freescale/s32g2.dtsi > @@ -162,6 +162,159 @@ jtag-grp4 { > slew-rate = <166>; > }; > }; > + > + pinctrl_usdhc0: usdhc0grp-pins { > + usdhc0-grp0 { > + pinmux = <0x2e1>, > + <0x381>; > + output-enable; > + bias-pull-down; > + slew-rate = <150>; > + }; > + > + usdhc0-grp1 { > + pinmux = <0x2f1>, > + <0x301>, > + <0x311>, > + <0x321>, > + <0x331>, > + <0x341>, > + <0x351>, > + <0x361>, > + <0x371>; > + output-enable; > + input-enable; > + bias-pull-up; > + slew-rate = <150>; > + }; > + > + usdhc0-grp2 { > + pinmux = <0x391>; > + output-enable; > + slew-rate = <150>; > + }; > + > + usdhc0-grp3 { > + pinmux = <0x3a0>; > + input-enable; > + slew-rate = <150>; > + }; > + > + usdhc0-grp4 { > + pinmux = <0x2032>, > + <0x2042>, > + <0x2052>, > + <0x2062>, > + <0x2072>, > + <0x2082>, > + <0x2092>, > + <0x20a2>, > + <0x20b2>, > + <0x20c2>; > + }; > + }; > + > + pinctrl_usdhc0_100mhz: usdhc0-100mhzgrp-pins { > + usdhc0-100mhz-grp0 { > + pinmux = <0x2e1>, > + <0x381>; > + output-enable; > + bias-pull-down; > + slew-rate = <150>; > + }; > + > + usdhc0-100mhz-grp1 { > + pinmux = <0x2f1>, > + <0x301>, > + <0x311>, > + <0x321>, > + <0x331>, > + <0x341>, > + <0x351>, > + <0x361>, > + <0x371>; > + output-enable; > + input-enable; > + bias-pull-up; > + slew-rate = <150>; > + }; > + > + usdhc0-100mhz-grp2 { > + pinmux = <0x391>; > + output-enable; > + slew-rate = <150>; > + }; > + > + usdhc0-100mhz-grp3 { > + pinmux = <0x3a0>; > + input-enable; > + slew-rate = <150>; > + }; > + > + usdhc0-100mhz-grp4 { > + pinmux = <0x2032>, > + <0x2042>, > + <0x2052>, > + <0x2062>, > + <0x2072>, > + <0x2082>, > + <0x2092>, > + <0x20a2>, > + <0x20b2>, > + <0x20c2>; > + }; > + }; > + > + pinctrl_usdhc0_200mhz: usdhc0-200mhzgrp-pins { > + usdhc0-200mhz-grp0 { > + pinmux = <0x2e1>, > + <0x381>; > + output-enable; > + bias-pull-down; > + slew-rate = <208>; > + }; > + > + usdhc0-200mhz-grp1 { > + pinmux = <0x2f1>, > + <0x301>, > + <0x311>, > + <0x321>, > + <0x331>, > + <0x341>, > + <0x351>, > + <0x361>, > + <0x371>; > + output-enable; > + input-enable; > + bias-pull-up; > + slew-rate = <208>; > + }; > + > + usdhc0-200mhz-grp2 { > + pinmux = <0x391>; > + output-enable; > + slew-rate = <208>; > + }; > + > + usdhc0-200mhz-grp3 { > + pinmux = <0x3a0>; > + input-enable; > + slew-rate = <208>; > + }; > + > + usdhc0-200mhz-grp4 { > + pinmux = <0x2032>, > + <0x2042>, > + <0x2052>, > + <0x2062>, > + <0x2072>, > + <0x2082>, > + <0x2092>, > + <0x20a2>, > + <0x20b2>, > + <0x20c2>; > + }; > + }; > }; > > uart0: serial@401c8000 { > diff --git a/arch/arm64/boot/dts/freescale/s32g274a-evb.dts b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts > index dbe498798bd9..7ab917f547ef 100644 > --- a/arch/arm64/boot/dts/freescale/s32g274a-evb.dts > +++ b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts > @@ -34,6 +34,10 @@ &uart0 { > }; > > &usdhc0 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc0>; > + pinctrl-1 = <&pinctrl_usdhc0_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc0_200mhz>; > disable-wp; > status = "okay"; > }; > diff --git a/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts > index ab1e5caaeae7..8739f63771bc 100644 > --- a/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts > +++ b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts > @@ -40,6 +40,10 @@ &uart1 { > }; > > &usdhc0 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc0>; > + pinctrl-1 = <&pinctrl_usdhc0_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc0_200mhz>; > disable-wp; > status = "okay"; > }; > diff --git a/arch/arm64/boot/dts/freescale/s32g3.dtsi b/arch/arm64/boot/dts/freescale/s32g3.dtsi > index b4226a9143c8..6c572ffe37ca 100644 > --- a/arch/arm64/boot/dts/freescale/s32g3.dtsi > +++ b/arch/arm64/boot/dts/freescale/s32g3.dtsi > @@ -219,6 +219,159 @@ jtag-grp4 { > slew-rate = <166>; > }; > }; > + > + pinctrl_usdhc0: usdhc0grp-pins { > + usdhc0-grp0 { > + pinmux = <0x2e1>, > + <0x381>; > + output-enable; > + bias-pull-down; > + slew-rate = <150>; > + }; > + > + usdhc0-grp1 { > + pinmux = <0x2f1>, > + <0x301>, > + <0x311>, > + <0x321>, > + <0x331>, > + <0x341>, > + <0x351>, > + <0x361>, > + <0x371>; > + output-enable; > + input-enable; > + bias-pull-up; > + slew-rate = <150>; > + }; > + > + usdhc0-grp2 { > + pinmux = <0x391>; > + output-enable; > + slew-rate = <150>; > + }; > + > + usdhc0-grp3 { > + pinmux = <0x3a0>; > + input-enable; > + slew-rate = <150>; > + }; > + > + usdhc0-grp4 { > + pinmux = <0x2032>, > + <0x2042>, > + <0x2052>, > + <0x2062>, > + <0x2072>, > + <0x2082>, > + <0x2092>, > + <0x20a2>, > + <0x20b2>, > + <0x20c2>; > + }; > + }; > + > + pinctrl_usdhc0_100mhz: usdhc0-100mhzgrp-pins { > + usdhc0-100mhz-grp0 { > + pinmux = <0x2e1>, > + <0x381>; > + output-enable; > + bias-pull-down; > + slew-rate = <150>; > + }; > + > + usdhc0-100mhz-grp1 { > + pinmux = <0x2f1>, > + <0x301>, > + <0x311>, > + <0x321>, > + <0x331>, > + <0x341>, > + <0x351>, > + <0x361>, > + <0x371>; > + output-enable; > + input-enable; > + bias-pull-up; > + slew-rate = <150>; > + }; > + > + usdhc0-100mhz-grp2 { > + pinmux = <0x391>; > + output-enable; > + slew-rate = <150>; > + }; > + > + usdhc0-100mhz-grp3 { > + pinmux = <0x3a0>; > + input-enable; > + slew-rate = <150>; > + }; > + > + usdhc0-100mhz-grp4 { > + pinmux = <0x2032>, > + <0x2042>, > + <0x2052>, > + <0x2062>, > + <0x2072>, > + <0x2082>, > + <0x2092>, > + <0x20a2>, > + <0x20b2>, > + <0x20c2>; > + }; > + }; > + > + pinctrl_usdhc0_200mhz: usdhc0-200mhzgrp-pins { > + usdhc0-200mhz-grp0 { > + pinmux = <0x2e1>, > + <0x381>; > + output-enable; > + bias-pull-down; > + slew-rate = <208>; > + }; > + > + usdhc0-200mhz-grp1 { > + pinmux = <0x2f1>, > + <0x301>, > + <0x311>, > + <0x321>, > + <0x331>, > + <0x341>, > + <0x351>, > + <0x361>, > + <0x371>; > + output-enable; > + input-enable; > + bias-pull-up; > + slew-rate = <208>; > + }; > + > + usdhc0-200mhz-grp2 { > + pinmux = <0x391>; > + output-enable; > + slew-rate = <208>; > + }; > + > + usdhc0-200mhz-grp3 { > + pinmux = <0x3a0>; > + input-enable; > + slew-rate = <208>; > + }; > + > + usdhc0-200mhz-grp4 { > + pinmux = <0x2032>, > + <0x2042>, > + <0x2052>, > + <0x2062>, > + <0x2072>, > + <0x2082>, > + <0x2092>, > + <0x20a2>, > + <0x20b2>, > + <0x20c2>; > + }; > + }; > }; > > uart0: serial@401c8000 { > diff --git a/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts b/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts > index 176e5af191c8..828e353455b5 100644 > --- a/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts > +++ b/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts > @@ -40,6 +40,10 @@ &uart1 { > }; > > &usdhc0 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc0>; > + pinctrl-1 = <&pinctrl_usdhc0_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc0_200mhz>; > bus-width = <8>; > disable-wp; > status = "okay";
On 30/08/2024 13:33, Ciprian Costea wrote: > From: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> > > Adding 100mhz & 200mhz pinmux support for uSDHC helps to enable > higher speed modes for SD (SDR50, DDR50, SDR104) and > eMMC (such as HS200, HS400/HS400ES). > > Signed-off-by: Radu Pirea <radu-nicolae.pirea@nxp.com> > Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> > --- > arch/arm64/boot/dts/freescale/s32g2.dtsi | 153 ++++++++++++++++++ > .../arm64/boot/dts/freescale/s32g274a-evb.dts | 4 + > .../boot/dts/freescale/s32g274a-rdb2.dts | 4 + > arch/arm64/boot/dts/freescale/s32g3.dtsi | 153 ++++++++++++++++++ > .../boot/dts/freescale/s32g399a-rdb3.dts | 4 + > 5 files changed, 318 insertions(+) > > diff --git a/arch/arm64/boot/dts/freescale/s32g2.dtsi b/arch/arm64/boot/dts/freescale/s32g2.dtsi > index fa054bfe7d5c..7be430b78c83 100644 > --- a/arch/arm64/boot/dts/freescale/s32g2.dtsi > +++ b/arch/arm64/boot/dts/freescale/s32g2.dtsi > @@ -162,6 +162,159 @@ jtag-grp4 { > slew-rate = <166>; > }; > }; > + > + pinctrl_usdhc0: usdhc0grp-pins { > + usdhc0-grp0 { Are you sure that this passes dtbs_check W=1? Best regards, Krzysztof
On 9/17/2024 8:44 PM, Krzysztof Kozlowski wrote: > On 30/08/2024 13:33, Ciprian Costea wrote: >> From: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> >> >> Adding 100mhz & 200mhz pinmux support for uSDHC helps to enable >> higher speed modes for SD (SDR50, DDR50, SDR104) and >> eMMC (such as HS200, HS400/HS400ES). >> >> Signed-off-by: Radu Pirea <radu-nicolae.pirea@nxp.com> >> Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> >> --- >> arch/arm64/boot/dts/freescale/s32g2.dtsi | 153 ++++++++++++++++++ >> .../arm64/boot/dts/freescale/s32g274a-evb.dts | 4 + >> .../boot/dts/freescale/s32g274a-rdb2.dts | 4 + >> arch/arm64/boot/dts/freescale/s32g3.dtsi | 153 ++++++++++++++++++ >> .../boot/dts/freescale/s32g399a-rdb3.dts | 4 + >> 5 files changed, 318 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/freescale/s32g2.dtsi b/arch/arm64/boot/dts/freescale/s32g2.dtsi >> index fa054bfe7d5c..7be430b78c83 100644 >> --- a/arch/arm64/boot/dts/freescale/s32g2.dtsi >> +++ b/arch/arm64/boot/dts/freescale/s32g2.dtsi >> @@ -162,6 +162,159 @@ jtag-grp4 { >> slew-rate = <166>; >> }; >> }; >> + >> + pinctrl_usdhc0: usdhc0grp-pins { >> + usdhc0-grp0 { > > Are you sure that this passes dtbs_check W=1? > > Best regards, > Krzysztof > Hello Krzysztof, I've checked as follows: $ make ARCH=arm64 CHECK_DTBS=y W=1 freescale/s32g274a-evb.dtb freescale/s32g274a-rdb2.dtb freescale/s32g399a-rdb3.dtb DTC [C] arch/arm64/boot/dts/freescale/s32g274a-evb.dtb DTC [C] arch/arm64/boot/dts/freescale/s32g274a-rdb2.dtb DTC [C] arch/arm64/boot/dts/freescale/s32g399a-rdb3.dtb Best Regards, Ciprian
diff --git a/arch/arm64/boot/dts/freescale/s32g2.dtsi b/arch/arm64/boot/dts/freescale/s32g2.dtsi index fa054bfe7d5c..7be430b78c83 100644 --- a/arch/arm64/boot/dts/freescale/s32g2.dtsi +++ b/arch/arm64/boot/dts/freescale/s32g2.dtsi @@ -162,6 +162,159 @@ jtag-grp4 { slew-rate = <166>; }; }; + + pinctrl_usdhc0: usdhc0grp-pins { + usdhc0-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <150>; + }; + + usdhc0-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <150>; + }; + + usdhc0-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <150>; + }; + + usdhc0-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <150>; + }; + + usdhc0-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; + + pinctrl_usdhc0_100mhz: usdhc0-100mhzgrp-pins { + usdhc0-100mhz-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; + + pinctrl_usdhc0_200mhz: usdhc0-200mhzgrp-pins { + usdhc0-200mhz-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; }; uart0: serial@401c8000 { diff --git a/arch/arm64/boot/dts/freescale/s32g274a-evb.dts b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts index dbe498798bd9..7ab917f547ef 100644 --- a/arch/arm64/boot/dts/freescale/s32g274a-evb.dts +++ b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts @@ -34,6 +34,10 @@ &uart0 { }; &usdhc0 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc0>; + pinctrl-1 = <&pinctrl_usdhc0_100mhz>; + pinctrl-2 = <&pinctrl_usdhc0_200mhz>; disable-wp; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts index ab1e5caaeae7..8739f63771bc 100644 --- a/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts +++ b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts @@ -40,6 +40,10 @@ &uart1 { }; &usdhc0 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc0>; + pinctrl-1 = <&pinctrl_usdhc0_100mhz>; + pinctrl-2 = <&pinctrl_usdhc0_200mhz>; disable-wp; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/s32g3.dtsi b/arch/arm64/boot/dts/freescale/s32g3.dtsi index b4226a9143c8..6c572ffe37ca 100644 --- a/arch/arm64/boot/dts/freescale/s32g3.dtsi +++ b/arch/arm64/boot/dts/freescale/s32g3.dtsi @@ -219,6 +219,159 @@ jtag-grp4 { slew-rate = <166>; }; }; + + pinctrl_usdhc0: usdhc0grp-pins { + usdhc0-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <150>; + }; + + usdhc0-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <150>; + }; + + usdhc0-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <150>; + }; + + usdhc0-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <150>; + }; + + usdhc0-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; + + pinctrl_usdhc0_100mhz: usdhc0-100mhzgrp-pins { + usdhc0-100mhz-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <150>; + }; + + usdhc0-100mhz-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; + + pinctrl_usdhc0_200mhz: usdhc0-200mhzgrp-pins { + usdhc0-200mhz-grp0 { + pinmux = <0x2e1>, + <0x381>; + output-enable; + bias-pull-down; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp1 { + pinmux = <0x2f1>, + <0x301>, + <0x311>, + <0x321>, + <0x331>, + <0x341>, + <0x351>, + <0x361>, + <0x371>; + output-enable; + input-enable; + bias-pull-up; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp2 { + pinmux = <0x391>; + output-enable; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp3 { + pinmux = <0x3a0>; + input-enable; + slew-rate = <208>; + }; + + usdhc0-200mhz-grp4 { + pinmux = <0x2032>, + <0x2042>, + <0x2052>, + <0x2062>, + <0x2072>, + <0x2082>, + <0x2092>, + <0x20a2>, + <0x20b2>, + <0x20c2>; + }; + }; }; uart0: serial@401c8000 { diff --git a/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts b/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts index 176e5af191c8..828e353455b5 100644 --- a/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts +++ b/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts @@ -40,6 +40,10 @@ &uart1 { }; &usdhc0 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc0>; + pinctrl-1 = <&pinctrl_usdhc0_100mhz>; + pinctrl-2 = <&pinctrl_usdhc0_200mhz>; bus-width = <8>; disable-wp; status = "okay";