mbox series

[v2,0/5] Add support for PCIe3 on x1e80100

Message ID 20240913083724.1217691-1-quic_qianyu@quicinc.com
Headers show
Series Add support for PCIe3 on x1e80100 | expand

Message

Qiang Yu Sept. 13, 2024, 8:37 a.m. UTC 
This series add support for PCIe3 on x1e80100.

PCIe3 needs additional set of clocks, regulators and new set of PCIe QMP
PHY configuration compare other PCIe instances on x1e80100. Hence add
required resource configuration and usage for PCIe3.

v2->v1:
1. Squash [PATCH 1/8], [PATCH 2/8],[PATCH 3/8] into one patch and make the
   indentation consistent.
2. Put dts patch at the end of the patchset.
3. Put dt-binding patch at the first of the patchset.
4. Add a new patch where opp-table is added in dt-binding to avoid dtbs
   checking error.
5. Remove GCC_PCIE_3_AUX_CLK, RPMH_CXO_CLK, put in TCSR_PCIE_8L_CLKREF_EN
   as ref.
6. Remove lane_broadcasting.
7. Add 64 bit bar, Remove GCC_PCIE_3_PIPE_CLK_SRC, 
   GCC_CFG_NOC_PCIE_ANOC_SOUTH_AHB_CLK is changed to
   GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK.
8. Add Reviewed-by tag.
9. Remove [PATCH 7/8], [PATCH 8/8].

Qiang Yu (5):
  dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the X1E80100
    QMP PCIe PHY Gen4 x8
  dt-bindings: PCI: qcom: Add OPP table for X1E80100
  phy: qcom: qmp: Add phy register and clk setting for x1e80100 PCIe3
  clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks
  arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100

 .../bindings/pci/qcom,pcie-x1e80100.yaml      |   4 +
 .../phy/qcom,sc8280xp-qmp-pcie-phy.yaml       |   3 +
 arch/arm64/boot/dts/qcom/x1e80100.dtsi        | 202 ++++++++++++++++-
 drivers/clk/qcom/gcc-x1e80100.c               |  10 +-
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 211 ++++++++++++++++++
 .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h    |  25 +++
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h |  19 ++
 7 files changed, 468 insertions(+), 6 deletions(-)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h

Comments

Krishna chaitanya chundru Sept. 14, 2024, 3:59 a.m. UTC | #1 
Hi qiang,

In next series can you add logic in controller driver
to have new ops for this x1e80100 since this hardware
has smmuv3 support but currently the ops_1_9_0 ops which
is being used has configuring bdf to sid table which will
be not present for this devices.


- Krishna Chaitanya.

On 9/13/2024 2:07 PM, Qiang Yu wrote:
> This series add support for PCIe3 on x1e80100.
> 
> PCIe3 needs additional set of clocks, regulators and new set of PCIe QMP
> PHY configuration compare other PCIe instances on x1e80100. Hence add
> required resource configuration and usage for PCIe3.
> 
> v2->v1:
> 1. Squash [PATCH 1/8], [PATCH 2/8],[PATCH 3/8] into one patch and make the
>     indentation consistent.
> 2. Put dts patch at the end of the patchset.
> 3. Put dt-binding patch at the first of the patchset.
> 4. Add a new patch where opp-table is added in dt-binding to avoid dtbs
>     checking error.
> 5. Remove GCC_PCIE_3_AUX_CLK, RPMH_CXO_CLK, put in TCSR_PCIE_8L_CLKREF_EN
>     as ref.
> 6. Remove lane_broadcasting.
> 7. Add 64 bit bar, Remove GCC_PCIE_3_PIPE_CLK_SRC,
>     GCC_CFG_NOC_PCIE_ANOC_SOUTH_AHB_CLK is changed to
>     GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK.
> 8. Add Reviewed-by tag.
> 9. Remove [PATCH 7/8], [PATCH 8/8].
> 
> Qiang Yu (5):
>    dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the X1E80100
>      QMP PCIe PHY Gen4 x8
>    dt-bindings: PCI: qcom: Add OPP table for X1E80100
>    phy: qcom: qmp: Add phy register and clk setting for x1e80100 PCIe3
>    clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks
>    arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100
> 
>   .../bindings/pci/qcom,pcie-x1e80100.yaml      |   4 +
>   .../phy/qcom,sc8280xp-qmp-pcie-phy.yaml       |   3 +
>   arch/arm64/boot/dts/qcom/x1e80100.dtsi        | 202 ++++++++++++++++-
>   drivers/clk/qcom/gcc-x1e80100.c               |  10 +-
>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 211 ++++++++++++++++++
>   .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h    |  25 +++
>   drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h |  19 ++
>   7 files changed, 468 insertions(+), 6 deletions(-)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h
>
Qiang Yu Sept. 19, 2024, 2:14 p.m. UTC | #2 
On 9/14/2024 11:59 AM, Krishna Chaitanya Chundru wrote:
> Hi qiang,
>
> In next series can you add logic in controller driver
> to have new ops for this x1e80100 since this hardware
> has smmuv3 support but currently the ops_1_9_0 ops which
> is being used has configuring bdf to sid table which will
> be not present for this devices.
>
Sure, bdf2sid map is not supported and required since we use smmuv3 for
pcie on x1e80100. Can I add a new ops which is same as ops_1_9_0 basically
and only config_sid callback is removed. Or add a new flag to determine if
we need to config bdf2sid map like no_l0s.

Hi Mani, what do you think about this?

Thanks,
Qiang
>
> - Krishna Chaitanya.
>
> On 9/13/2024 2:07 PM, Qiang Yu wrote:
>> This series add support for PCIe3 on x1e80100.
>>
>> PCIe3 needs additional set of clocks, regulators and new set of PCIe QMP
>> PHY configuration compare other PCIe instances on x1e80100. Hence add
>> required resource configuration and usage for PCIe3.
>>
>> v2->v1:
>> 1. Squash [PATCH 1/8], [PATCH 2/8],[PATCH 3/8] into one patch and 
>> make the
>>     indentation consistent.
>> 2. Put dts patch at the end of the patchset.
>> 3. Put dt-binding patch at the first of the patchset.
>> 4. Add a new patch where opp-table is added in dt-binding to avoid dtbs
>>     checking error.
>> 5. Remove GCC_PCIE_3_AUX_CLK, RPMH_CXO_CLK, put in 
>> TCSR_PCIE_8L_CLKREF_EN
>>     as ref.
>> 6. Remove lane_broadcasting.
>> 7. Add 64 bit bar, Remove GCC_PCIE_3_PIPE_CLK_SRC,
>>     GCC_CFG_NOC_PCIE_ANOC_SOUTH_AHB_CLK is changed to
>>     GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK.
>> 8. Add Reviewed-by tag.
>> 9. Remove [PATCH 7/8], [PATCH 8/8].
>>
>> Qiang Yu (5):
>>    dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the X1E80100
>>      QMP PCIe PHY Gen4 x8
>>    dt-bindings: PCI: qcom: Add OPP table for X1E80100
>>    phy: qcom: qmp: Add phy register and clk setting for x1e80100 PCIe3
>>    clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks
>>    arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100
>>
>>   .../bindings/pci/qcom,pcie-x1e80100.yaml      |   4 +
>>   .../phy/qcom,sc8280xp-qmp-pcie-phy.yaml       |   3 +
>>   arch/arm64/boot/dts/qcom/x1e80100.dtsi        | 202 ++++++++++++++++-
>>   drivers/clk/qcom/gcc-x1e80100.c               |  10 +-
>>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 211 ++++++++++++++++++
>>   .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h    |  25 +++
>>   drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h |  19 ++
>>   7 files changed, 468 insertions(+), 6 deletions(-)
>>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h
>>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h
>>
Manivannan Sadhasivam Sept. 22, 2024, 5:09 p.m. UTC | #3 
On Thu, Sep 19, 2024 at 10:14:06PM +0800, Qiang Yu wrote:
> 
> On 9/14/2024 11:59 AM, Krishna Chaitanya Chundru wrote:
> > Hi qiang,
> > 
> > In next series can you add logic in controller driver
> > to have new ops for this x1e80100 since this hardware
> > has smmuv3 support but currently the ops_1_9_0 ops which
> > is being used has configuring bdf to sid table which will
> > be not present for this devices.
> > 
> Sure, bdf2sid map is not supported and required since we use smmuv3 for
> pcie on x1e80100. Can I add a new ops which is same as ops_1_9_0 basically
> and only config_sid callback is removed. Or add a new flag to determine if
> we need to config bdf2sid map like no_l0s.
> 
> Hi Mani, what do you think about this?
> 

Good question. IMO it is better to add a new ops even though it duplictes the
callbacks. Because the newer platforms are not going to need this bdf2sid map
anyway. But if we add a flag to determine that, then the check will become,

	if (pcie->cfg->ops->config_sid && !pcie->cfg->smmuv3)
		...

And this doesn't look good as both conditions are false for X1E80100 i.e., it
doesn't need bdf2sid mapping and it is also a SMMUv3 platform. Moreover having
two checks here makes it confusing also.

So let's use a new callback. But please mention the IP revision in comments as
like other ops.

- Mani

> Thanks,
> Qiang
> > 
> > - Krishna Chaitanya.
> > 
> > On 9/13/2024 2:07 PM, Qiang Yu wrote:
> > > This series add support for PCIe3 on x1e80100.
> > > 
> > > PCIe3 needs additional set of clocks, regulators and new set of PCIe QMP
> > > PHY configuration compare other PCIe instances on x1e80100. Hence add
> > > required resource configuration and usage for PCIe3.
> > > 
> > > v2->v1:
> > > 1. Squash [PATCH 1/8], [PATCH 2/8],[PATCH 3/8] into one patch and
> > > make the
> > >     indentation consistent.
> > > 2. Put dts patch at the end of the patchset.
> > > 3. Put dt-binding patch at the first of the patchset.
> > > 4. Add a new patch where opp-table is added in dt-binding to avoid dtbs
> > >     checking error.
> > > 5. Remove GCC_PCIE_3_AUX_CLK, RPMH_CXO_CLK, put in
> > > TCSR_PCIE_8L_CLKREF_EN
> > >     as ref.
> > > 6. Remove lane_broadcasting.
> > > 7. Add 64 bit bar, Remove GCC_PCIE_3_PIPE_CLK_SRC,
> > >     GCC_CFG_NOC_PCIE_ANOC_SOUTH_AHB_CLK is changed to
> > >     GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK.
> > > 8. Add Reviewed-by tag.
> > > 9. Remove [PATCH 7/8], [PATCH 8/8].
> > > 
> > > Qiang Yu (5):
> > >    dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the X1E80100
> > >      QMP PCIe PHY Gen4 x8
> > >    dt-bindings: PCI: qcom: Add OPP table for X1E80100
> > >    phy: qcom: qmp: Add phy register and clk setting for x1e80100 PCIe3
> > >    clk: qcom: gcc-x1e80100: Fix halt_check for pipediv2 clocks
> > >    arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100
> > > 
> > >   .../bindings/pci/qcom,pcie-x1e80100.yaml      |   4 +
> > >   .../phy/qcom,sc8280xp-qmp-pcie-phy.yaml       |   3 +
> > >   arch/arm64/boot/dts/qcom/x1e80100.dtsi        | 202 ++++++++++++++++-
> > >   drivers/clk/qcom/gcc-x1e80100.c               |  10 +-
> > >   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 211 ++++++++++++++++++
> > >   .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h    |  25 +++
> > >   drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h |  19 ++
> > >   7 files changed, 468 insertions(+), 6 deletions(-)
> > >   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_30.h
> > >   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_30.h
> > >