diff mbox series

[v3,2/4] arm64: dts: imx: Add imx8mp-iota2-lumpy board

Message ID 20240923151417.1665431-3-michal.vokac@ysoft.com (mailing list archive)
State Superseded
Headers show
Series Add support for new IMX8MP based board | expand

Commit Message

Michal Vokáč Sept. 23, 2024, 3:14 p.m. UTC 
The IOTA2 Lumpy board is based on the i.MX8MPlus EVK.

Basic features are:
- 4GB LPDDR4
- 64GB eMMC
- 2x 1GB Ethernet
- USB 3.0 Type-C dual role port, without power delivery
- USB 3.0 Type-A host port
- RGB LED - PWM driven
- speaker - PWM driven
- RTC with super capacitor backup

Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
---
v3:
- Dropped pinctrl-names property from &usb_dwc3_1 node.
v2:
- Dropped unused property from pwm4 node.
- Sorted all nodes and properties using dt-format tool from Frank.

 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../boot/dts/freescale/imx8mp-iota2-lumpy.dts | 423 ++++++++++++++++++
 2 files changed, 424 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts

Comments

Marco Felsch Sept. 24, 2024, 7:16 a.m. UTC | #1 
Hi Michael,

thanks for the patch, please see below some notes but nothing crucial.

On 24-09-23, Michal Vokáč wrote:
> The IOTA2 Lumpy board is based on the i.MX8MPlus EVK.
> 
> Basic features are:
> - 4GB LPDDR4
> - 64GB eMMC
> - 2x 1GB Ethernet
> - USB 3.0 Type-C dual role port, without power delivery
> - USB 3.0 Type-A host port
> - RGB LED - PWM driven
> - speaker - PWM driven
> - RTC with super capacitor backup
> 
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
> ---
> v3:
> - Dropped pinctrl-names property from &usb_dwc3_1 node.
> v2:
> - Dropped unused property from pwm4 node.
> - Sorted all nodes and properties using dt-format tool from Frank.
> 
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../boot/dts/freescale/imx8mp-iota2-lumpy.dts | 423 ++++++++++++++++++
>  2 files changed, 424 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 9d3df8b218a2..aa26a50b7bb4 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -171,6 +171,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-iota2-lumpy.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-navqp.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts b/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts
> new file mode 100644
> index 000000000000..120e6b87a000
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts
> @@ -0,0 +1,423 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2023 Y Soft
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mp.dtsi"
> +
> +/ {
> +	compatible = "ysoft,imx8mp-iota2-lumpy", "fsl,imx8mp";
> +	model = "Y Soft i.MX8MPlus IOTA2 Lumpy board";
> +
> +	beeper {
> +		compatible = "pwm-beeper";
> +		pwms = <&pwm4 0 500000 0>;
> +	};
> +
> +	chosen {
> +		stdout-path = &uart2;
> +	};
> +
> +	gpio_keys: gpio-keys {
> +		compatible = "gpio-keys";
> +		pinctrl-0 = <&pinctrl_gpio_keys>;
> +		pinctrl-names = "default";
> +
> +		button-reset {
> +			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> +			label = "Factory RESET";
> +			linux,code = <BTN_0>;
> +		};
> +	};
> +
> +	reg_usb_host: regulator-usb-host {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
> +		pinctrl-0 = <&pinctrl_usb_host_vbus>;
> +		pinctrl-names = "default";
> +		regulator-max-microvolt = <5000000>;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-name = "usb-host";
> +	};
> +
> +	memory@40000000 {
> +		reg = <0x0 0x40000000 0 0x80000000>,
> +		      <0x1 0x00000000 0 0x80000000>;
> +		device_type = "memory";
> +	};
> +};
> +
> +&A53_0 {
> +	cpu-supply = <&reg_arm>;
> +};
> +
> +&A53_1 {
> +	cpu-supply = <&reg_arm>;
> +};
> +
> +&A53_2 {
> +	cpu-supply = <&reg_arm>;
> +};
> +
> +&A53_3 {
> +	cpu-supply = <&reg_arm>;
> +};
> +
> +&eqos {
> +	phy-handle = <&ethphy0>;
> +	phy-mode = "rgmii-id";
> +	pinctrl-0 = <&pinctrl_eqos>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@0 {
> +			reg = <0>;
> +			interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
> +			interrupt-parent = <&gpio3>;
> +			micrel,led-mode = <0>;
> +			pinctrl-0 = <&pinctrl_ethphy0>;
> +			pinctrl-names = "default";
> +			reset-assert-us = <1000>;
> +			reset-deassert-us = <1000>;
> +			reset-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +};
> +
> +&fec {
> +	fsl,magic-packet;
> +	phy-handle = <&ethphy1>;
> +	phy-mode = "rgmii-id";
> +	pinctrl-0 = <&pinctrl_fec>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy1: ethernet-phy@0 {
> +			reg = <0>;
> +			interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> +			interrupt-parent = <&gpio3>;
> +			micrel,led-mode = <0>;
> +			pinctrl-0 = <&pinctrl_ethphy1>;
> +			pinctrl-names = "default";
> +			reset-assert-us = <1000>;
> +			reset-deassert-us = <1000>;
> +			reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	clock-frequency = <400000>;
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	pmic@25 {
> +		compatible = "nxp,pca9450c";
> +		reg = <0x25>;
> +		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +		interrupt-parent = <&gpio1>;
> +		pinctrl-0 = <&pinctrl_pmic>;
> +		pinctrl-names = "default";
> +
> +		regulators {
> +			BUCK1 {
> +				regulator-always-on;

All your PMIC rails are marked as regulator-always-on. I didn't expect
this from a (battery backed) IOT platform.

> +				regulator-boot-on;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-min-microvolt = <720000>;
> +				regulator-name = "BUCK1";
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			reg_arm: BUCK2 {
> +				nxp,dvs-run-voltage = <950000>;
> +				nxp,dvs-standby-voltage = <850000>;
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <1025000>;
> +				regulator-min-microvolt = <720000>;
> +				regulator-name = "BUCK2";
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			BUCK4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <3600000>;
> +				regulator-min-microvolt = <3000000>;
> +				regulator-name = "BUCK4";
> +			};
> +
> +			BUCK5 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <1950000>;
> +				regulator-min-microvolt = <1650000>;
> +				regulator-name = "BUCK5";
> +			};
> +
> +			BUCK6 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <1155000>;
> +				regulator-min-microvolt = <1045000>;
> +				regulator-name = "BUCK6";
> +			};
> +
> +			LDO1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <1950000>;
> +				regulator-min-microvolt = <1650000>;
> +				regulator-name = "LDO1";
> +			};
> +
> +			LDO3 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <1890000>;
> +				regulator-min-microvolt = <1710000>;
> +				regulator-name = "LDO3";
> +			};
> +
> +			LDO4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <950000>;
> +				regulator-min-microvolt = <850000>;
> +				regulator-name = "LDO4";
> +			};
> +
> +			LDO5 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-name = "LDO5";
> +			};
> +		};
> +	};
> +};
> +
> +&i2c2 {
> +	clock-frequency = <400000>;
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	rtc: rtc@68 {
> +		compatible = "dallas,ds1341";
> +		reg = <0x68>;
> +	};
> +};
> +
> +&iomuxc {

Albeit we do sort the node names alphabetical we put the iomuxc at the
very end at least for the i.MX platforms. Maybe this is something
Frank's tool should be aware of in the future :)

> +	pinctrl_eqos: eqosgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC		0x2
> +			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO		0x2
> +			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0	0x90
> +			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1	0x90
> +			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2	0x90
> +			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3	0x90
> +			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL	0x90
> +			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90
> +			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0	0x16
> +			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1	0x16
> +			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2	0x16
> +			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3	0x16
> +			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL	0x16
> +			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x16
> +		>;
> +	};
> +
> +	pinctrl_ethphy0: ethphy0grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21		0x10
> +			MX8MP_IOMUXC_SAI5_RXD1__GPIO3_IO22		0x10
> +		>;
> +	};
> +
> +	pinctrl_ethphy1: ethphy1grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19		0x10
> +			MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20		0x10
> +		>;
> +	};
> +
> +	pinctrl_fec: fecgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x2
> +			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x2
> +			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x90
> +			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x90
> +			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x90
> +			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x90
> +			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x90
> +			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x90
> +			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x16
> +			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x16
> +			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x16
> +			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x16
> +			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x16
> +			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x16
> +		>;
> +	};
> +
> +	pinctrl_gpio_keys: gpiokeysgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07	0x80
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c2
> +			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c2
> +		>;
> +	};
> +
> +	pinctrl_i2c2: i2c2grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c2
> +			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c2
> +		>;
> +	};
> +
> +	pinctrl_pmic: pmicgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03	0x1c0
> +		>;
> +	};
> +
> +	pinctrl_pwm4: pwm4grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_SAI3_MCLK__PWM4_OUT	0x102
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x0
> +			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x0
> +		>;
> +	};
> +
> +	pinctrl_usb_host_vbus: usb1grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR	0x0
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
> +			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d4
> +			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4
> +			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4
> +			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4
> +			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4
> +			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4
> +			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4
> +			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4
> +			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d4
> +			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x194
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
> +			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
> +			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
> +			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
> +			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
> +			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
> +			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
> +			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
> +			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
> +			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
> +			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
> +		>;
> +	};
> +
> +	pinctrl_usdhc3: usdhc3grp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x190
> +			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d0
> +			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d0
> +			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d0
> +			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d0
> +			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d0
> +			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d0
> +			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d0
> +			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d0
> +			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d0
> +			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x190
> +		>;
> +	};
> +
> +	pinctrl_wdog: wdoggrp {
> +		fsl,pins = <
> +			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0x166
> +		>;
> +	};
> +};
> +
> +&pwm4 {
> +	pinctrl-0 = <&pinctrl_pwm4>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> +
> +&usb3_1 {
> +	status = "okay";
> +};
> +
> +&usb3_phy1 {
> +	vbus-supply = <&reg_usb_host>;
> +	status = "okay";
> +};
> +
> +&usb_dwc3_1 {
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&usdhc3 {
> +	assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
> +	assigned-clock-rates = <400000000>;
> +	bus-width = <8>;
> +	non-removable;

Please move the bus-width and non-removeable properties below the
pinctrl-* properties.

> +	pinctrl-0 = <&pinctrl_usdhc3>;
> +	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	status = "okay";
> +};
> +
> +&wdog1 {
> +	fsl,ext-reset-output;

This property should be put below the pinctrl-* properties.

Regards,
  Marco

> +	pinctrl-0 = <&pinctrl_wdog>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};
> -- 
> 2.43.0
> 
> 
>
Michal Vokáč Sept. 24, 2024, 9:06 a.m. UTC | #2 
On 24. 09. 24 9:16, Marco Felsch wrote:
> Hi Michael,
> 
> thanks for the patch, please see below some notes but nothing crucial.
> 
>> +
>> +&i2c1 {
>> +	clock-frequency = <400000>;
>> +	pinctrl-0 = <&pinctrl_i2c1>;
>> +	pinctrl-names = "default";
>> +	status = "okay";
>> +
>> +	pmic@25 {
>> +		compatible = "nxp,pca9450c";
>> +		reg = <0x25>;
>> +		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
>> +		interrupt-parent = <&gpio1>;
>> +		pinctrl-0 = <&pinctrl_pmic>;
>> +		pinctrl-names = "default";
>> +
>> +		regulators {
>> +			BUCK1 {
>> +				regulator-always-on;
> 
> All your PMIC rails are marked as regulator-always-on. I didn't expect
> this from a (battery backed) IOT platform.

These are correct. I is not a battery backed device. It operates on 12V
from wall power adapter. It is more like an Ethernet router/edge device
for a B2B solution.

>> +				regulator-boot-on;
>> +				regulator-max-microvolt = <1000000>;
>> +				regulator-min-microvolt = <720000>;
>> +				regulator-name = "BUCK1";
>> +				regulator-ramp-delay = <3125>;
>> +			};
>> +


>> +
>> +&iomuxc {
> 
> Albeit we do sort the node names alphabetical we put the iomuxc at the
> very end at least for the i.MX platforms. Maybe this is something
> Frank's tool should be aware of in the future :)

I am used to do it the way you say. I just accepted Frank's comment
and that it is maybe a new standard to sort all nodes strictly alphabetically.

OK, I will move the iomuxc node back to the end as usual.

>> +&usdhc3 {
>> +	assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
>> +	assigned-clock-rates = <400000000>;
>> +	bus-width = <8>;
>> +	non-removable;
> 
> Please move the bus-width and non-removeable properties below the
> pinctrl-* properties.

OK.

>> +	pinctrl-0 = <&pinctrl_usdhc3>;
>> +	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
>> +	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
>> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
>> +	status = "okay";
>> +};
>> +
>> +&wdog1 {
>> +	fsl,ext-reset-output;
> 
> This property should be put below the pinctrl-* properties.

OK.

Thank you for the review,
Michal

>> +	pinctrl-0 = <&pinctrl_wdog>;
>> +	pinctrl-names = "default";
>> +	status = "okay";
>> +};
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 9d3df8b218a2..aa26a50b7bb4 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -171,6 +171,7 @@  dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-iota2-lumpy.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-navqp.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts b/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts
new file mode 100644
index 000000000000..120e6b87a000
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts
@@ -0,0 +1,423 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2023 Y Soft
+ */
+
+/dts-v1/;
+
+#include "imx8mp.dtsi"
+
+/ {
+	compatible = "ysoft,imx8mp-iota2-lumpy", "fsl,imx8mp";
+	model = "Y Soft i.MX8MPlus IOTA2 Lumpy board";
+
+	beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm4 0 500000 0>;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		pinctrl-names = "default";
+
+		button-reset {
+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+			label = "Factory RESET";
+			linux,code = <BTN_0>;
+		};
+	};
+
+	reg_usb_host: regulator-usb-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&pinctrl_usb_host_vbus>;
+		pinctrl-names = "default";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-host";
+	};
+
+	memory@40000000 {
+		reg = <0x0 0x40000000 0 0x80000000>,
+		      <0x1 0x00000000 0 0x80000000>;
+		device_type = "memory";
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_arm>;
+};
+
+&eqos {
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&pinctrl_eqos>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+			interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-parent = <&gpio3>;
+			micrel,led-mode = <0>;
+			pinctrl-0 = <&pinctrl_ethphy0>;
+			pinctrl-names = "default";
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			reset-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&fec {
+	fsl,magic-packet;
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&pinctrl_fec>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@0 {
+			reg = <0>;
+			interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-parent = <&gpio3>;
+			micrel,led-mode = <0>;
+			pinctrl-0 = <&pinctrl_ethphy1>;
+			pinctrl-names = "default";
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	pmic@25 {
+		compatible = "nxp,pca9450c";
+		reg = <0x25>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio1>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		pinctrl-names = "default";
+
+		regulators {
+			BUCK1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1000000>;
+				regulator-min-microvolt = <720000>;
+				regulator-name = "BUCK1";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_arm: BUCK2 {
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1025000>;
+				regulator-min-microvolt = <720000>;
+				regulator-name = "BUCK2";
+				regulator-ramp-delay = <3125>;
+			};
+
+			BUCK4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3600000>;
+				regulator-min-microvolt = <3000000>;
+				regulator-name = "BUCK4";
+			};
+
+			BUCK5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1950000>;
+				regulator-min-microvolt = <1650000>;
+				regulator-name = "BUCK5";
+			};
+
+			BUCK6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1155000>;
+				regulator-min-microvolt = <1045000>;
+				regulator-name = "BUCK6";
+			};
+
+			LDO1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1950000>;
+				regulator-min-microvolt = <1650000>;
+				regulator-name = "LDO1";
+			};
+
+			LDO3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1890000>;
+				regulator-min-microvolt = <1710000>;
+				regulator-name = "LDO3";
+			};
+
+			LDO4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <950000>;
+				regulator-min-microvolt = <850000>;
+				regulator-name = "LDO4";
+			};
+
+			LDO5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "LDO5";
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rtc: rtc@68 {
+		compatible = "dallas,ds1341";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC		0x2
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO		0x2
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0	0x90
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1	0x90
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2	0x90
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3	0x90
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL	0x90
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0	0x16
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1	0x16
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2	0x16
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3	0x16
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL	0x16
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x16
+		>;
+	};
+
+	pinctrl_ethphy0: ethphy0grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21		0x10
+			MX8MP_IOMUXC_SAI5_RXD1__GPIO3_IO22		0x10
+		>;
+	};
+
+	pinctrl_ethphy1: ethphy1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19		0x10
+			MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20		0x10
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x2
+			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x2
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x90
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x90
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x90
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x90
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x90
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x90
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x16
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x16
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x16
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x16
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x16
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x16
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07	0x80
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03	0x1c0
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_MCLK__PWM4_OUT	0x102
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x0
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x0
+		>;
+	};
+
+	pinctrl_usb_host_vbus: usb1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR	0x0
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0x166
+		>;
+	};
+};
+
+&pwm4 {
+	pinctrl-0 = <&pinctrl_pwm4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-0 = <&pinctrl_uart2>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&usb3_phy1 {
+	vbus-supply = <&reg_usb_host>;
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	non-removable;
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	status = "okay";
+};
+
+&wdog1 {
+	fsl,ext-reset-output;
+	pinctrl-0 = <&pinctrl_wdog>;
+	pinctrl-names = "default";
+	status = "okay";
+};