@@ -1676,7 +1676,7 @@ static int ahci_init_msi(struct pci_dev *pdev, unsigned int n_ports,
/*
* If number of MSIs is less than number of ports then Sharing Last
* Message mode could be enforced. In this case assume that advantage
- * of multipe MSIs is negated and use single MSI mode instead.
+ * of multiple MSIs is negated and use single MSI mode instead.
*/
if (n_ports > 1) {
nvec = pci_alloc_irq_vectors(pdev, n_ports, INT_MAX,
@@ -511,7 +511,7 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv)
if (imxpriv->type == AHCI_IMX6Q || imxpriv->type == AHCI_IMX6QP) {
/*
- * set PHY Paremeters, two steps to configure the GPR13,
+ * set PHY Parameters, two steps to configure the GPR13,
* one write for rest of parameters, mask of first write
* is 0x07ffffff, and the other one write for setting
* the mpll_clk_en.
@@ -534,7 +534,7 @@ static int xgene_ahci_softreset(struct ata_link *link, unsigned int *class,
/**
* xgene_ahci_handle_broken_edge_irq - Handle the broken irq.
- * @host: Host that recieved the irq
+ * @host: Host that received the irq
* @irq_masked: HOST_IRQ_STAT value
*
* For hardware with broken edge trigger latch
@@ -86,7 +86,7 @@ static void ata_acpi_detach_device(struct ata_port *ap, struct ata_device *dev)
* @dev: ATA device ACPI event occurred (can be NULL)
* @event: ACPI event which occurred
*
- * All ACPI bay / device realted events end up in this function. If
+ * All ACPI bay / device related events end up in this function. If
* the event is port-wide @dev is NULL. If the event is specific to a
* device, @dev points to it.
*
@@ -832,7 +832,7 @@ void ata_acpi_on_resume(struct ata_port *ap)
dev->flags |= ATA_DFLAG_ACPI_PENDING;
}
} else {
- /* SATA _GTF needs to be evaulated after _SDD and
+ /* SATA _GTF needs to be evaluated after _SDD and
* there's no reason to evaluate IDE _GTF early
* without _STM. Clear cache and schedule _GTF.
*/
@@ -81,7 +81,7 @@ static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
int control = 0;
/*
- * See Intel Document 298600-004 for the timing programing rules
+ * See Intel Document 298600-004 for the timing programming rules
* for PIIX/ICH. The 8213 is a clone so very similar
*/
@@ -183,7 +183,7 @@ static void octeon_cf_set_piomode(struct ata_port *ap, struct ata_device *dev)
reg_tim.s.ale = 0;
/* Not used */
reg_tim.s.page = 0;
- /* Time after IORDY to coninue to assert the data */
+ /* Time after IORDY to continue to assert the data */
reg_tim.s.wait = 0;
/* Time to wait to complete the cycle. */
reg_tim.s.pause = pause;
@@ -70,7 +70,7 @@ static void oldpiix_set_piomode (struct ata_port *ap, struct ata_device *adev)
int control = 0;
/*
- * See Intel Document 298600-004 for the timing programing rules
+ * See Intel Document 298600-004 for the timing programming rules
* for PIIX/ICH. Note that the early PIIX does not have the slave
* timing port at 0x44.
*/
@@ -45,7 +45,7 @@ static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
int control = 0;
/*
- * See Intel Document 298600-004 for the timing programing rules
+ * See Intel Document 298600-004 for the timing programming rules
* for PIIX/ICH. Note that the early PIIX does not have the slave
* timing port at 0x44. The Radisys is a relative of the PIIX
* but not the same so be careful.
Correctly spelled comments make it easier for the reader to understand the code. Fix typos: 'multipe' ==> 'multiple', 'Paremeters' ==> 'Parameters', 'recieved' ==> 'received', 'realted' ==> 'related', 'evaulated' ==> 'evaluated', 'programing' ==> 'programming', 'coninue' ==> 'continue', 'Decriptor' ==> 'Descriptor', 'Lable' ==> 'Label', 'transmiting' ==> 'transmitting', 'correspondance' ==> 'correspondence', 'claculation' ==> 'calculation', 'everone' ==> 'everyone', 'contruct' ==> 'construct'. Signed-off-by: Yan Zhen <yanzhen@vivo.com> --- drivers/ata/ahci.c | 2 +- drivers/ata/ahci_imx.c | 2 +- drivers/ata/ahci_xgene.c | 2 +- drivers/ata/libata-acpi.c | 4 ++-- drivers/ata/pata_it8213.c | 2 +- drivers/ata/pata_octeon_cf.c | 2 +- drivers/ata/pata_oldpiix.c | 2 +- drivers/ata/pata_radisys.c | 2 +- 8 files changed, 9 insertions(+), 9 deletions(-)