[5/5] clk: meson: add A5 clock peripherals controller driver

Commit Message

Xianwei Zhao via B4 Relay Sept. 14, 2024, 5:25 a.m. UTC

From: Chuan Liu <[e-mail]>

Add the peripherals clock controller driver in the A5 SoC family.

Signed-off-by: Chuan Liu <[e-mail]>
Signed-off-by: Xianwei Zhao <[e-mail]>
---
 drivers/clk/meson/Kconfig          |   14 +
 drivers/clk/meson/Makefile         |    1 +
 drivers/clk/meson/a5-peripherals.c | 1471 ++++++++++++++++++++++++++++++++++++
 3 files changed, 1486 insertions(+)

Comments

Jerome Brunet Sept. 24, 2024, 3:09 p.m. UTC | #1

On Sat 14 Sep 2024 at 13:25, Xianwei Zhao via B4 Relay <[e-mail]> wrote:

> From: Chuan Liu <[e-mail]>
>
> Add the peripherals clock controller driver in the A5 SoC family.
>
> Signed-off-by: Chuan Liu <[e-mail]>
> Signed-off-by: Xianwei Zhao <[e-mail]>
> ---
>  drivers/clk/meson/Kconfig          |   14 +
>  drivers/clk/meson/Makefile         |    1 +
>  drivers/clk/meson/a5-peripherals.c | 1471 ++++++++++++++++++++++++++++++++++++
>  3 files changed, 1486 insertions(+)
>
> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
> index 2a713276e46c..21845edcd8ef 100644
> --- a/drivers/clk/meson/Kconfig
> +++ b/drivers/clk/meson/Kconfig
> @@ -146,6 +146,20 @@ config COMMON_CLK_A5_PLL
>  	  Say Y if you want the board to work, because PLLs are the parent
>  	  of most peripherals.
>  
> +config COMMON_CLK_A5_PERIPHERALS
> +	tristate "Amlogic A5 peripherals clock controller"
> +	depends on ARM64
> +	default y
> +	imply ARM_SCMI_PROTOCOL

same

> +	imply COMMON_CLK_SCMI
> +	imply COMMON_CLK_A5_PLL
> +	select COMMON_CLK_MESON_REGMAP
> +	select COMMON_CLK_MESON_DUALDIV
> +	select COMMON_CLK_MESON_CLKC_UTILS
> +	help
> +	  Support for the Peripherals clock controller on Amlogic AV40x device,
> +	  AKA A5. Say Y if you want the peripherals clock to work.
> +
>  config COMMON_CLK_C3_PLL
>  	tristate "Amlogic C3 PLL clock controller"
>  	depends on ARM64
> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
> index fc4b8a723145..58236c6e8377 100644
> --- a/drivers/clk/meson/Makefile
> +++ b/drivers/clk/meson/Makefile
> @@ -21,6 +21,7 @@ obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>  obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
>  obj-$(CONFIG_COMMON_CLK_A1_PERIPHERALS) += a1-peripherals.o
>  obj-$(CONFIG_COMMON_CLK_A5_PLL) += a5-pll.o
> +obj-$(CONFIG_COMMON_CLK_A5_PERIPHERALS) += a5-peripherals.o
>  obj-$(CONFIG_COMMON_CLK_C3_PLL) += c3-pll.o
>  obj-$(CONFIG_COMMON_CLK_C3_PERIPHERALS) += c3-peripherals.o
>  obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
> diff --git a/drivers/clk/meson/a5-peripherals.c b/drivers/clk/meson/a5-peripherals.c
> new file mode 100644
> index 000000000000..c28da340a5af
> --- /dev/null
> +++ b/drivers/clk/meson/a5-peripherals.c
> @@ -0,0 +1,1471 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Amlogic A5 Peripherals Clock Controller Driver
> + *
> + * Copyright (c) 2024 Amlogic, inc.
> + * Author: Chuan Liu <[e-mail]>
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/platform_device.h>
> +#include "clk-regmap.h"
> +#include "clk-dualdiv.h"
> +#include "meson-clkc-utils.h"
> +#include <dt-bindings/clock/amlogic,a5-peripherals-clkc.h>
> +
> +#define CLKCTRL_RTC_BY_OSCIN_CTRL0		0x8
> +#define CLKCTRL_RTC_BY_OSCIN_CTRL1		0xc
> +#define CLKCTRL_RTC_CTRL			0x10
> +#define CLKCTRL_SYS_CLK_EN0_REG0		0x44
> +#define CLKCTRL_SYS_CLK_EN0_REG1		0x48
> +#define CLKCTRL_DSPA_CLK_CTRL0			0x9c
> +#define CLKCTRL_CLK12_24_CTRL			0xa8
> +#define CLKCTRL_AXI_CLK_EN0			0xac
> +#define CLKCTRL_TS_CLK_CTRL			0x158
> +#define CLKCTRL_ETH_CLK_CTRL			0x164
> +#define CLKCTRL_NAND_CLK_CTRL			0x168
> +#define CLKCTRL_SD_EMMC_CLK_CTRL		0x16c
> +#define CLKCTRL_SPICC_CLK_CTRL			0x174
> +#define CLKCTRL_GEN_CLK_CTRL			0x178
> +#define CLKCTRL_SAR_CLK_CTRL0			0x17c
> +#define CLKCTRL_PWM_CLK_AB_CTRL			0x180
> +#define CLKCTRL_PWM_CLK_CD_CTRL			0x184
> +#define CLKCTRL_PWM_CLK_EF_CTRL			0x188
> +#define CLKCTRL_PWM_CLK_GH_CTRL			0x18c
> +#define CLKCTRL_NNA_CLK_CNTL			0x220

Again I see a lot of holes in there. Please make sure there is only
clocks in the whole region you are claiming for the device.

Otherwise it is fine to register as many controller as necessary

> +
> +static struct clk_regmap rtc_xtal_clkin = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_RTC_BY_OSCIN_CTRL0,
> +		.bit_idx = 31,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "rtc_xtal_clkin",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_data = &(const struct clk_parent_data) {
> +			.fw_name = "oscin",
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static const struct meson_clk_dualdiv_param rtc_32k_div_table[] = {
> +	{ 733, 732, 8, 11, 1 },
> +	{ /* sentinel */ }
> +};
> +
> +static struct clk_regmap rtc_32k_div = {
> +	.data = &(struct meson_clk_dualdiv_data) {
> +		.n1 = {
> +			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL0,
> +			.shift   = 0,
> +			.width   = 12,
> +		},
> +		.n2 = {
> +			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL0,
> +			.shift   = 12,
> +			.width   = 12,
> +		},
> +		.m1 = {
> +			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL1,
> +			.shift   = 0,
> +			.width   = 12,
> +		},
> +		.m2 = {
> +			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL1,
> +			.shift   = 12,
> +			.width   = 12,
> +		},
> +		.dual = {
> +			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL0,
> +			.shift   = 28,
> +			.width   = 1,
> +		},
> +		.table = rtc_32k_div_table,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "rtc_32k_div",
> +		.ops = &meson_clk_dualdiv_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&rtc_xtal_clkin.hw
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static const struct clk_parent_data rtc_32k_mux_parent_data[] = {
> +	{ .hw = &rtc_32k_div.hw },
> +	{ .hw = &rtc_xtal_clkin.hw }
> +};
> +
> +static struct clk_regmap rtc_32k_mux = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_RTC_BY_OSCIN_CTRL1,
> +		.mask = 0x1,
> +		.shift = 24,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "rtc_32k_mux",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = rtc_32k_mux_parent_data,
> +		.num_parents = ARRAY_SIZE(rtc_32k_mux_parent_data),
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap rtc_32k = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_RTC_BY_OSCIN_CTRL0,
> +		.bit_idx = 30,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "rtc_32k",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&rtc_32k_mux.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static const struct clk_parent_data rtc_clk_mux_parent_data[] = {
> +	{ .fw_name = "oscin" },
> +	{ .hw = &rtc_32k.hw },
> +	{ .fw_name = "pad_osc" }
> +};
> +
> +static struct clk_regmap rtc_clk = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_RTC_CTRL,
> +		.mask = 0x3,
> +		.shift = 0,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "rtc_clk",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = rtc_clk_mux_parent_data,
> +		.num_parents = ARRAY_SIZE(rtc_clk_mux_parent_data),
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +#define A4_CLK_GATE(_name, _reg, _bit, _fw_name, _ops, _flags)
> \

A4 ??? everything else is A5 ? Please explain

> +struct clk_regmap _name = {						\
> +	.data = &(struct clk_regmap_gate_data){				\
> +		.offset = (_reg),					\
> +		.bit_idx = (_bit),					\
> +	},								\
> +	.hw.init = &(struct clk_init_data) {				\
> +		.name = #_name,						\
> +		.ops = _ops,						\
> +		.parent_data = &(const struct clk_parent_data) {	\
> +			.fw_name = #_fw_name,				\
> +		},							\
> +		.num_parents = 1,					\
> +		.flags = (_flags),					\
> +	},								\
> +}
> +
> +#define A4_SYS_GATE(_name, _reg, _bit, _flags)				\
> +	A4_CLK_GATE(_name, _reg, _bit, sysclk,				\
> +		    &clk_regmap_gate_ops, _flags)
> +
> +#define A4_SYS_GATE_RO(_name, _reg, _bit)				\
> +	A4_CLK_GATE(_name, _reg, _bit, sysclk,				\
> +		    &clk_regmap_gate_ro_ops, 0)

Looks like a copy/paste of the C3. If this pattern keeps on repeating,
it would be nice to make a common definition

> +
> +static A4_SYS_GATE(sys_reset_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 1, 0);
> +static A4_SYS_GATE(sys_pwr_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 3, 0);
> +static A4_SYS_GATE(sys_pad_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 4, 0);
> +static A4_SYS_GATE(sys_ctrl,		CLKCTRL_SYS_CLK_EN0_REG0, 5, 0);
> +static A4_SYS_GATE(sys_ts_pll,		CLKCTRL_SYS_CLK_EN0_REG0, 6, 0);
> +
> +/*
> + * NOTE: sys_dev_arb provides the clock to the ETH and SPICC arbiters that
> + * access the AXI bus.
> + */
> +static A4_SYS_GATE(sys_dev_arb,		CLKCTRL_SYS_CLK_EN0_REG0, 7, 0);
> +
> +/*
> + * FIXME: sys_mmc_pclk provides the clock for the DDR PHY, DDR will only be
> + * initialized in bl2, and this clock should not be touched in linux.
> + */
> +static A4_SYS_GATE_RO(sys_mmc_pclk,	CLKCTRL_SYS_CLK_EN0_REG0, 8);
> +static A4_SYS_GATE(sys_mailbox,		CLKCTRL_SYS_CLK_EN0_REG0, 10, 0);
> +
> +/*
> + * NOTE: sys_cpu_ctrl provides the clock for CPU controller. After clock is
> + * disabled, cpu_clk and other key CPU-related configurations cannot take effect.
> + */
> +static A4_SYS_GATE(sys_cpu_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 11, CLK_IS_CRITICAL);
> +static A4_SYS_GATE(sys_jtag_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 12, 0);
> +static A4_SYS_GATE(sys_ir_ctrl,		CLKCTRL_SYS_CLK_EN0_REG0, 13, 0);
> +
> +/*
> + * NOTE: sys_irq_ctrl provides the clock for IRQ controller. The IRQ controller
> + * collects and distributes the interrupt signal to the GIC, PWR_CTRL, and
> + * AOCPU. If the clock is disabled, interrupt-related functions will occurs an
> + * exception.
> + */
> +static A4_SYS_GATE(sys_irq_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 14, CLK_IS_CRITICAL);
> +static A4_SYS_GATE(sys_msr_clk,		CLKCTRL_SYS_CLK_EN0_REG0, 15, 0);
> +static A4_SYS_GATE(sys_rom,		CLKCTRL_SYS_CLK_EN0_REG0, 16, 0);
> +static A4_SYS_GATE(sys_cpu_apb,		CLKCTRL_SYS_CLK_EN0_REG0, 18, 0);
> +static A4_SYS_GATE(sys_rsa,		CLKCTRL_SYS_CLK_EN0_REG0, 19, 0);
> +static A4_SYS_GATE(sys_sar_adc,		CLKCTRL_SYS_CLK_EN0_REG0, 20, 0);
> +static A4_SYS_GATE(sys_startup,		CLKCTRL_SYS_CLK_EN0_REG0, 21, 0);
> +static A4_SYS_GATE(sys_secure,		CLKCTRL_SYS_CLK_EN0_REG0, 22, 0);
> +static A4_SYS_GATE(sys_spifc,		CLKCTRL_SYS_CLK_EN0_REG0, 23, 0);
> +static A4_SYS_GATE(sys_dspa,		CLKCTRL_SYS_CLK_EN0_REG0, 24, 0);
> +static A4_SYS_GATE(sys_nna,		CLKCTRL_SYS_CLK_EN0_REG0, 25, 0);
> +static A4_SYS_GATE(sys_eth_mac,		CLKCTRL_SYS_CLK_EN0_REG0, 26, 0);
> +
> +/*
> + * FIXME: sys_gic provides the clock for GIC(Generic Interrupt Controller).
> + * After clock is disabled, The GIC cannot work properly. At present, the driver
> + * used by our GIC is the public driver in kernel, and there is no management
> + * clock in the driver.
> + */
> +static A4_SYS_GATE(sys_gic,		CLKCTRL_SYS_CLK_EN0_REG0, 27, CLK_IS_CRITICAL);

The GIC has a driver. If it needs clock, maybe it should request it and
enable it, maybe as optional.

> +static A4_SYS_GATE(sys_rama,		CLKCTRL_SYS_CLK_EN0_REG0, 28, 0);
> +
> +/*
> + * NOTE: sys_big_nic provides the clock to the control bus of the NIC(Network
> + * Interface Controller) between multiple devices(CPU, DDR, RAM, ROM, GIC,
> + * SPIFC, CAPU, JTAG, EMMC, SDIO, sec_top, USB, Audio, ETH, SPICC) in the
> + * system. After clock is disabled, The NIC cannot work.
> + */

This comment looks like a clock that should be passed as ressource to a
bus or power-domain to be properly manage. This is a pattern that keeps
on repeating. I will not block you on it this time around but I strong
suggest you fix up the situation on the related platform. Next time
around, the reason won't be a valid one.

> +static A4_SYS_GATE(sys_big_nic,		CLKCTRL_SYS_CLK_EN0_REG0, 29, CLK_IS_CRITICAL);
> +static A4_SYS_GATE(sys_ramb,		CLKCTRL_SYS_CLK_EN0_REG0, 30, 0);
> +static A4_SYS_GATE(sys_audio_top,	CLKCTRL_SYS_CLK_EN0_REG1, 0, 0);
> +static A4_SYS_GATE(sys_audio_vad,	CLKCTRL_SYS_CLK_EN0_REG1, 1, 0);
> +static A4_SYS_GATE(sys_usb,		CLKCTRL_SYS_CLK_EN0_REG1, 2, 0);
> +static A4_SYS_GATE(sys_sd_emmc_a,	CLKCTRL_SYS_CLK_EN0_REG1, 3, 0);
> +static A4_SYS_GATE(sys_sd_emmc_c,	CLKCTRL_SYS_CLK_EN0_REG1, 4, 0);
> +static A4_SYS_GATE(sys_pwm_ab,		CLKCTRL_SYS_CLK_EN0_REG1, 5, 0);
> +static A4_SYS_GATE(sys_pwm_cd,		CLKCTRL_SYS_CLK_EN0_REG1, 6, 0);
> +static A4_SYS_GATE(sys_pwm_ef,		CLKCTRL_SYS_CLK_EN0_REG1, 7, 0);
> +static A4_SYS_GATE(sys_pwm_gh,		CLKCTRL_SYS_CLK_EN0_REG1, 8, 0);
> +static A4_SYS_GATE(sys_spicc_1,		CLKCTRL_SYS_CLK_EN0_REG1, 9, 0);
> +static A4_SYS_GATE(sys_spicc_0,		CLKCTRL_SYS_CLK_EN0_REG1, 10, 0);
> +static A4_SYS_GATE(sys_uart_a,		CLKCTRL_SYS_CLK_EN0_REG1, 11, 0);
> +static A4_SYS_GATE(sys_uart_b,		CLKCTRL_SYS_CLK_EN0_REG1, 12, 0);
> +static A4_SYS_GATE(sys_uart_c,		CLKCTRL_SYS_CLK_EN0_REG1, 13, 0);
> +static A4_SYS_GATE(sys_uart_d,		CLKCTRL_SYS_CLK_EN0_REG1, 14, 0);
> +static A4_SYS_GATE(sys_uart_e,		CLKCTRL_SYS_CLK_EN0_REG1, 15, 0);
> +static A4_SYS_GATE(sys_i2c_m_a,		CLKCTRL_SYS_CLK_EN0_REG1, 16, 0);
> +static A4_SYS_GATE(sys_i2c_m_b,		CLKCTRL_SYS_CLK_EN0_REG1, 17, 0);
> +static A4_SYS_GATE(sys_i2c_m_c,		CLKCTRL_SYS_CLK_EN0_REG1, 18, 0);
> +static A4_SYS_GATE(sys_i2c_m_d,		CLKCTRL_SYS_CLK_EN0_REG1, 19, 0);
> +static A4_SYS_GATE(sys_rtc,		CLKCTRL_SYS_CLK_EN0_REG1, 21, 0);
> +
> +#define A4_AXI_GATE(_name, _reg, _bit, _flags)				\
> +	A4_CLK_GATE(_name, _reg, _bit, axiclk,				\
> +		    &clk_regmap_gate_ops, _flags)
> +
> +static A4_AXI_GATE(axi_audio_vad,	CLKCTRL_AXI_CLK_EN0, 0, 0);
> +static A4_AXI_GATE(axi_audio_top,	CLKCTRL_AXI_CLK_EN0, 1, 0);
> +
> +/*
> + * NOTE: axi_sys_nic provides the clock to the AXI bus of the system NIC. After
> + * clock is disabled, The NIC cannot work.
> + */
> +static A4_AXI_GATE(axi_sys_nic,		CLKCTRL_AXI_CLK_EN0, 2, CLK_IS_CRITICAL);
> +static A4_AXI_GATE(axi_ramb,		CLKCTRL_AXI_CLK_EN0, 5, 0);
> +static A4_AXI_GATE(axi_rama,		CLKCTRL_AXI_CLK_EN0, 6, 0);
> +
> +/*
> + * NOTE: axi_cpu_dmc provides the clock to the AXI bus where the CPU accesses
> + * the DDR. After clock is disabled, The CPU will not have access to the DDR.
> + */
> +static A4_AXI_GATE(axi_cpu_dmc,		CLKCTRL_AXI_CLK_EN0, 7, CLK_IS_CRITICAL);
> +static A4_AXI_GATE(axi_nna,		CLKCTRL_AXI_CLK_EN0, 12, 0);
> +
> +/*
> + * NOTE: axi_dev1_dmc provides the clock for the peripherals(EMMC, SDIO,
> + * sec_top, USB, Audio) to access the AXI bus of the DDR.
> + */

Same.

> +static A4_AXI_GATE(axi_dev1_dmc,	CLKCTRL_AXI_CLK_EN0, 13, 0);
> +
> +/*
> + * NOTE: axi_dev0_dmc provides the clock for the peripherals(ETH and SPICC)
> + * to access the AXI bus of the DDR.
> + */
> +static A4_AXI_GATE(axi_dev0_dmc,	CLKCTRL_AXI_CLK_EN0, 14, 0);
> +static A4_AXI_GATE(axi_dsp_dmc,		CLKCTRL_AXI_CLK_EN0, 15, 0);
> +
> +static struct clk_regmap clk_12_24m_in = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_CLK12_24_CTRL,
> +		.bit_idx = 11,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "clk_12_24m_in",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_data = &(const struct clk_parent_data) {
> +			.fw_name = "xtal_24m",
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap clk_12_24m = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_CLK12_24_CTRL,
> +		.shift = 10,
> +		.width = 1,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "clk_12_24m",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&clk_12_24m_in.hw
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +/* FIXME: set value 0 will div by 2 like value 1 */

Again, it is fine when it happens once, like the c3.
When the pattern starts repeating, it is time to do something about it.

> +static struct clk_regmap fclk_25m_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_CLK12_24_CTRL,
> +		.shift = 0,
> +		.width = 8,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "fclk_25m_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_data = &(const struct clk_parent_data) {
> +			.fw_name = "fix",
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap fclk_25m = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_CLK12_24_CTRL,
> +		.bit_idx = 12,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "fclk_25m",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&fclk_25m_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +/*
> + * Channel 3(ddr_dpll_pt_clk) is manged by the DDR module; channel 12(cts_msr_clk)
> + * is manged by clock measures module. Their hardware are out of clock tree.

Yet, they exist and should be part of the bindings since they are
obviously input to this clock.

> + * Channel 4 5 8 9 10 11 13 14 15 16 18 are not connected.
> + *
> + * gp1 is designed for DSU (DynamIQ Shared Unit) alone. It cannot be changed
> + * arbitrarily. gp1 is read-only in the kernel and is only open for debug purposes.
> + */
> +static u32 gen_parent_table[] = { 0, 1, 2, 6, 7, 17, 19, 20, 21, 22, 23, 24, 25,
> +				  26, 27, 28};
> +
> +static const struct clk_parent_data gen_parent_data[] = {
> +	{ .fw_name = "oscin" },
> +	{ .hw = &rtc_clk.hw },
> +	{ .fw_name = "sysplldiv16" },
> +	{ .fw_name = "gp1" },
> +	{ .fw_name = "hifi" },
> +	{ .fw_name = "cpudiv16" },
> +	{ .fw_name = "fdiv2" },
> +	{ .fw_name = "fdiv2p5" },
> +	{ .fw_name = "fdiv3" },
> +	{ .fw_name = "fdiv4" },
> +	{ .fw_name = "fdiv5" },
> +	{ .fw_name = "fdiv7" },
> +	{ .fw_name = "mpll0" },
> +	{ .fw_name = "mpll1" },
> +	{ .fw_name = "mpll2" },
> +	{ .fw_name = "mpll3" }
> +};
> +
> +static struct clk_regmap gen_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_GEN_CLK_CTRL,
> +		.mask = 0x1f,
> +		.shift = 12,
> +		.table = gen_parent_table,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "gen_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = gen_parent_data,
> +		.num_parents = ARRAY_SIZE(gen_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap gen_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_GEN_CLK_CTRL,
> +		.shift = 0,
> +		.width = 11,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "gen_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&gen_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap gen = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_GEN_CLK_CTRL,
> +		.bit_idx = 11,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "gen",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&gen_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static const struct clk_parent_data saradc_parent_data[] = {
> +	{ .fw_name = "oscin" },
> +	{ .fw_name = "sysclk" }
> +};
> +
> +static struct clk_regmap saradc_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_SAR_CLK_CTRL0,
> +		.mask = 0x1,
> +		.shift = 9,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "saradc_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = saradc_parent_data,
> +		.num_parents = ARRAY_SIZE(saradc_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap saradc_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_SAR_CLK_CTRL0,
> +		.shift = 0,
> +		.width = 8,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "saradc_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&saradc_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap saradc = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_SAR_CLK_CTRL0,
> +		.bit_idx = 8,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "saradc",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&saradc_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static const struct clk_parent_data pwm_parent_data[] = {
> +	{ .fw_name = "oscin" },
> +	{ .hw = &rtc_clk.hw },
> +	{ .fw_name = "fdiv4" },
> +	{ .fw_name = "fdiv3" }
> +};
> +
> +#define AML_PWM_CLK_MUX(_name, _reg, _shift) {			\
> +	.data = &(struct clk_regmap_mux_data) {			\
> +		.offset = _reg,					\
> +		.mask = 0x3,					\
> +		.shift = _shift,				\
> +	},							\
> +	.hw.init = &(struct clk_init_data) {			\
> +		.name = #_name "_sel",				\
> +		.ops = &clk_regmap_mux_ops,			\
> +		.parent_data = pwm_parent_data,			\
> +		.num_parents = ARRAY_SIZE(pwm_parent_data),	\
> +	},							\
> +}
> +
> +#define AML_PWM_CLK_DIV(_name, _reg, _shift) {			\
> +	.data = &(struct clk_regmap_div_data) {			\
> +		.offset = _reg,					\
> +		.shift = _shift,				\
> +		.width = 8,					\
> +	},							\
> +	.hw.init = &(struct clk_init_data) {			\
> +		.name = #_name "_div",				\
> +		.ops = &clk_regmap_divider_ops,			\
> +		.parent_names = (const char *[]) { #_name "_sel" },\
> +		.num_parents = 1,				\
> +		.flags = CLK_SET_RATE_PARENT,			\
> +	},							\
> +}
> +
> +#define AML_PWM_CLK_GATE(_name, _reg, _bit) {			\
> +	.data = &(struct clk_regmap_gate_data) {		\
> +		.offset = _reg,					\
> +		.bit_idx = _bit,				\
> +	},							\
> +	.hw.init = &(struct clk_init_data) {			\
> +		.name = #_name,					\
> +		.ops = &clk_regmap_gate_ops,			\
> +		.parent_names = (const char *[]) { #_name "_div" },\
> +		.num_parents = 1,				\
> +		.flags = CLK_SET_RATE_PARENT,			\
> +	},							\
> +}

Now the prefix is just AML ? please be consistent
And again, looks like a repeating pattern of these families you've been
upstreaming lately. 

> +
> +static struct clk_regmap pwm_a_sel =
> +	AML_PWM_CLK_MUX(pwm_a, CLKCTRL_PWM_CLK_AB_CTRL, 9);
> +static struct clk_regmap pwm_a_div =
> +	AML_PWM_CLK_DIV(pwm_a, CLKCTRL_PWM_CLK_AB_CTRL, 0);
> +static struct clk_regmap pwm_a =
> +	AML_PWM_CLK_GATE(pwm_a, CLKCTRL_PWM_CLK_AB_CTRL, 8);
> +
> +static struct clk_regmap pwm_b_sel =
> +	AML_PWM_CLK_MUX(pwm_b, CLKCTRL_PWM_CLK_AB_CTRL, 25);
> +static struct clk_regmap pwm_b_div =
> +	AML_PWM_CLK_DIV(pwm_b, CLKCTRL_PWM_CLK_AB_CTRL, 16);
> +static struct clk_regmap pwm_b =
> +	AML_PWM_CLK_GATE(pwm_b, CLKCTRL_PWM_CLK_AB_CTRL, 24);
> +
> +static struct clk_regmap pwm_c_sel =
> +	AML_PWM_CLK_MUX(pwm_c, CLKCTRL_PWM_CLK_CD_CTRL, 9);
> +static struct clk_regmap pwm_c_div =
> +	AML_PWM_CLK_DIV(pwm_c, CLKCTRL_PWM_CLK_CD_CTRL, 0);
> +static struct clk_regmap pwm_c =
> +	AML_PWM_CLK_GATE(pwm_c, CLKCTRL_PWM_CLK_CD_CTRL, 8);
> +
> +static struct clk_regmap pwm_d_sel =
> +	AML_PWM_CLK_MUX(pwm_d, CLKCTRL_PWM_CLK_CD_CTRL, 25);
> +static struct clk_regmap pwm_d_div =
> +	AML_PWM_CLK_DIV(pwm_d, CLKCTRL_PWM_CLK_CD_CTRL, 16);
> +static struct clk_regmap pwm_d =
> +	AML_PWM_CLK_GATE(pwm_d, CLKCTRL_PWM_CLK_CD_CTRL, 24);
> +
> +static struct clk_regmap pwm_e_sel =
> +	AML_PWM_CLK_MUX(pwm_e, CLKCTRL_PWM_CLK_EF_CTRL, 9);
> +static struct clk_regmap pwm_e_div =
> +	AML_PWM_CLK_DIV(pwm_e, CLKCTRL_PWM_CLK_EF_CTRL, 0);
> +static struct clk_regmap pwm_e =
> +	AML_PWM_CLK_GATE(pwm_e, CLKCTRL_PWM_CLK_EF_CTRL, 8);
> +
> +static struct clk_regmap pwm_f_sel =
> +	AML_PWM_CLK_MUX(pwm_f, CLKCTRL_PWM_CLK_EF_CTRL, 25);
> +static struct clk_regmap pwm_f_div =
> +	AML_PWM_CLK_DIV(pwm_f, CLKCTRL_PWM_CLK_EF_CTRL, 16);
> +static struct clk_regmap pwm_f =
> +	AML_PWM_CLK_GATE(pwm_f, CLKCTRL_PWM_CLK_EF_CTRL, 24);
> +
> +static struct clk_regmap pwm_g_sel =
> +	AML_PWM_CLK_MUX(pwm_g, CLKCTRL_PWM_CLK_GH_CTRL, 9);
> +static struct clk_regmap pwm_g_div =
> +	AML_PWM_CLK_DIV(pwm_g, CLKCTRL_PWM_CLK_GH_CTRL, 0);
> +static struct clk_regmap pwm_g =
> +	AML_PWM_CLK_GATE(pwm_g, CLKCTRL_PWM_CLK_GH_CTRL, 8);
> +
> +static struct clk_regmap pwm_h_sel =
> +	AML_PWM_CLK_MUX(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 25);
> +static struct clk_regmap pwm_h_div =
> +	AML_PWM_CLK_DIV(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 16);
> +static struct clk_regmap pwm_h =
> +	AML_PWM_CLK_GATE(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 24);
> +
> +/* Channel 7 is gp1. */

and ? if GP1 is RO, why can't you add it here ?

> +static const struct clk_parent_data spicc_parent_data[] = {
> +	{ .fw_name = "oscin" },
> +	{ .fw_name = "sysclk" },
> +	{ .fw_name = "fdiv4" },
> +	{ .fw_name = "fdiv3" },
> +	{ .fw_name = "fdiv2" },
> +	{ .fw_name = "fdiv5" },
> +	{ .fw_name = "fdiv7" }
> +};
> +
> +static struct clk_regmap spicc_0_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_SPICC_CLK_CTRL,
> +		.mask = 0x7,
> +		.shift = 7,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "spicc_0_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = spicc_parent_data,
> +		.num_parents = ARRAY_SIZE(spicc_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap spicc_0_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_SPICC_CLK_CTRL,
> +		.shift = 0,
> +		.width = 6,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "spicc_0_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&spicc_0_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap spicc_0 = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_SPICC_CLK_CTRL,
> +		.bit_idx = 6,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "spicc_0",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&spicc_0_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap spicc_1_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_SPICC_CLK_CTRL,
> +		.mask = 0x7,
> +		.shift = 23,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "spicc_1_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = spicc_parent_data,
> +		.num_parents = ARRAY_SIZE(spicc_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap spicc_1_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_SPICC_CLK_CTRL,
> +		.shift = 16,
> +		.width = 6,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "spicc_1_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&spicc_1_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap spicc_1 = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_SPICC_CLK_CTRL,
> +		.bit_idx = 22,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "spicc_1",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&spicc_1_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static const struct clk_parent_data emmc_parent_data[] = {
> +	{ .fw_name = "oscin" },
> +	{ .fw_name = "fdiv2" },
> +	{ .fw_name = "fdiv3" },
> +	{ .fw_name = "hifi" },
> +	{ .fw_name = "fdiv2p5" },
> +	{ .fw_name = "mpll2" },
> +	{ .fw_name = "mpll3" },
> +	{ .fw_name = "gp0" }
> +};
> +
> +static struct clk_regmap sd_emmc_a_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_SD_EMMC_CLK_CTRL,
> +		.mask = 0x7,
> +		.shift = 9,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "sd_emmc_a_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = emmc_parent_data,
> +		.num_parents = ARRAY_SIZE(emmc_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap sd_emmc_a_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_SD_EMMC_CLK_CTRL,
> +		.shift = 0,
> +		.width = 7,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "sd_emmc_a_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&sd_emmc_a_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap sd_emmc_a = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_SD_EMMC_CLK_CTRL,
> +		.bit_idx = 7,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "sd_emmc_a",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&sd_emmc_a_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap sd_emmc_c_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_NAND_CLK_CTRL,
> +		.mask = 0x7,
> +		.shift = 9,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "sd_emmc_c_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = emmc_parent_data,
> +		.num_parents = ARRAY_SIZE(emmc_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap sd_emmc_c_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_NAND_CLK_CTRL,
> +		.shift = 0,
> +		.width = 7,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "sd_emmc_c_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&sd_emmc_c_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap sd_emmc_c = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_NAND_CLK_CTRL,
> +		.bit_idx = 7,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "sd_emmc_c",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&sd_emmc_c_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap ts_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_TS_CLK_CTRL,
> +		.shift = 0,
> +		.width = 8,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "ts_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_data = &(const struct clk_parent_data) {
> +			.fw_name = "oscin",
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap ts = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_TS_CLK_CTRL,
> +		.bit_idx = 8,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "ts",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&ts_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_fixed_factor eth_125m_div = {
> +	.mult = 1,
> +	.div = 8,
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "eth_125m_div",
> +		.ops = &clk_fixed_factor_ops,
> +		.parent_data = &(const struct clk_parent_data) {
> +			.fw_name = "fdiv2",
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap eth_125m = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_ETH_CLK_CTRL,
> +		.bit_idx = 7,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "eth_125m",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&eth_125m_div.hw
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap eth_rmii_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_ETH_CLK_CTRL,
> +		.shift = 0,
> +		.width = 7,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "eth_rmii_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_data = &(const struct clk_parent_data) {
> +			.fw_name = "fdiv2",
> +		},
> +		.num_parents = 1,
> +	},
> +};
> +
> +static struct clk_regmap eth_rmii = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_ETH_CLK_CTRL,
> +		.bit_idx = 8,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "eth_rmii",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&eth_rmii_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +/* Channel 6 is gp1. */

same

> +static u32 dspa_parent_table[] = { 0, 1, 2, 3, 4, 5, 7};
> +
> +static const struct clk_parent_data dspa_parent_data[] = {
> +	{ .fw_name = "oscin" },
> +	{ .fw_name = "fdiv2p5" },
> +	{ .fw_name = "fdiv3" },
> +	{ .fw_name = "rtc" },
> +	{ .fw_name = "hifi" },
> +	{ .fw_name = "fdiv4" },
> +	{ .hw = &rtc_clk.hw }
> +};
> +
> +static struct clk_regmap dspa_0_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_DSPA_CLK_CTRL0,
> +		.mask = 0x7,
> +		.shift = 10,
> +		.table = dspa_parent_table,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "dspa_0_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = dspa_parent_data,
> +		.num_parents = ARRAY_SIZE(dspa_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap dspa_0_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_DSPA_CLK_CTRL0,
> +		.shift = 0,
> +		.width = 10,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "dspa_0_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&dspa_0_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap dspa_0 = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_DSPA_CLK_CTRL0,
> +		.bit_idx = 13,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "dspa_0",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&dspa_0_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap dspa_1_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_DSPA_CLK_CTRL0,
> +		.mask = 0x7,
> +		.shift = 26,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "dspa_1_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = dspa_parent_data,
> +		.num_parents = ARRAY_SIZE(dspa_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap dspa_1_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_DSPA_CLK_CTRL0,
> +		.shift = 16,
> +		.width = 10,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "dspa_1_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&dspa_1_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap dspa_1 = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_DSPA_CLK_CTRL0,
> +		.bit_idx = 29,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "dspa_1",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&dspa_1_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,

A word about SET_RATE_GATE ?

> +	},
> +};
> +
> +static struct clk_regmap dspa = {
> +	.data = &(struct clk_regmap_mux_data){
> +		.offset = CLKCTRL_DSPA_CLK_CTRL0,
> +		.mask = 0x1,
> +		.shift = 15,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "dspa",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&dspa_0.hw,
> +			&dspa_1.hw
> +		},
> +		.num_parents = 2,
> +		/*
> +		 * NOTE: This level of mux is "no glitch mux", and mux_0
> +		 * (here dspa_0) is not only the clock source for mux, but also
> +		 * provides a working clock for "no glitch mux". "no glitch mux"
> +		 * can be switched only when mux_0 has a clock input. Therefore,
> +		 * add flag CLK_OPS_PARENT_ENABLE to ensure that mux_0 has clock
> +		 * when "no glitch mux" works.
> +		 */
> +		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,

Humm CLK_OPS_PARENT_ENABLE is not how we have handling glitch free mux
so far. What changed ?

> +	},
> +};
> +
> +/* Channel 6 is gp1. */
> +static u32 nna_parent_table[] = { 0, 1, 2, 3, 4, 5, 7};
> +
> +static const struct clk_parent_data nna_parent_data[] = {
> +	{ .fw_name = "oscin" },
> +	{ .fw_name = "fdiv2p5" },
> +	{ .fw_name = "fdiv4" },
> +	{ .fw_name = "fdiv3" },
> +	{ .fw_name = "fdiv5" },
> +	{ .fw_name = "fdiv2" },
> +	{ .fw_name = "hifi" }
> +};
> +
> +static struct clk_regmap nna_core_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_NNA_CLK_CNTL,
> +		.mask = 0x7,
> +		.shift = 9,
> +		.table = nna_parent_table,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "nna_core_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = nna_parent_data,
> +		.num_parents = ARRAY_SIZE(nna_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap nna_core_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_NNA_CLK_CNTL,
> +		.shift = 0,
> +		.width = 7,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "nna_core_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&nna_core_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap nna_core = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_NNA_CLK_CNTL,
> +		.bit_idx = 8,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "nna_core",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&nna_core_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap nna_axi_sel = {
> +	.data = &(struct clk_regmap_mux_data) {
> +		.offset = CLKCTRL_NNA_CLK_CNTL,
> +		.mask = 0x7,
> +		.shift = 25,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "nna_axi_sel",
> +		.ops = &clk_regmap_mux_ops,
> +		.parent_data = nna_parent_data,
> +		.num_parents = ARRAY_SIZE(nna_parent_data),
> +	},
> +};
> +
> +static struct clk_regmap nna_axi_div = {
> +	.data = &(struct clk_regmap_div_data) {
> +		.offset = CLKCTRL_NNA_CLK_CNTL,
> +		.shift = 16,
> +		.width = 7,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "nna_axi_div",
> +		.ops = &clk_regmap_divider_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&nna_axi_sel.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_regmap nna_axi = {
> +	.data = &(struct clk_regmap_gate_data) {
> +		.offset = CLKCTRL_NNA_CLK_CNTL,
> +		.bit_idx = 24,
> +	},
> +	.hw.init = &(struct clk_init_data) {
> +		.name = "nna_axi",
> +		.ops = &clk_regmap_gate_ops,
> +		.parent_hws = (const struct clk_hw *[]) {
> +			&nna_axi_div.hw
> +		},
> +		.num_parents = 1,
> +		.flags = CLK_SET_RATE_PARENT,
> +	},
> +};
> +
> +static struct clk_hw *a5_periphs_hw_clks[] = {
> +	[CLKID_RTC_XTAL_CLKIN]		= &rtc_xtal_clkin.hw,
> +	[CLKID_RTC_32K_DIV]		= &rtc_32k_div.hw,
> +	[CLKID_RTC_32K_MUX]		= &rtc_32k_mux.hw,
> +	[CLKID_RTC_32K]			= &rtc_32k.hw,
> +	[CLKID_RTC_CLK]			= &rtc_clk.hw,
> +	[CLKID_SYS_RESET_CTRL]		= &sys_reset_ctrl.hw,
> +	[CLKID_SYS_PWR_CTRL]		= &sys_pwr_ctrl.hw,
> +	[CLKID_SYS_PAD_CTRL]		= &sys_pad_ctrl.hw,
> +	[CLKID_SYS_CTRL]		= &sys_ctrl.hw,
> +	[CLKID_SYS_TS_PLL]		= &sys_ts_pll.hw,
> +	[CLKID_SYS_DEV_ARB]		= &sys_dev_arb.hw,
> +	[CLKID_SYS_MMC_PCLK]		= &sys_mmc_pclk.hw,
> +	[CLKID_SYS_MAILBOX]		= &sys_mailbox.hw,
> +	[CLKID_SYS_CPU_CTRL]		= &sys_cpu_ctrl.hw,
> +	[CLKID_SYS_JTAG_CTRL]		= &sys_jtag_ctrl.hw,
> +	[CLKID_SYS_IR_CTRL]		= &sys_ir_ctrl.hw,
> +	[CLKID_SYS_IRQ_CTRL]		= &sys_irq_ctrl.hw,
> +	[CLKID_SYS_MSR_CLK]		= &sys_msr_clk.hw,
> +	[CLKID_SYS_ROM]			= &sys_rom.hw,
> +	[CLKID_SYS_CPU_ARB]		= &sys_cpu_apb.hw,
> +	[CLKID_SYS_RSA]			= &sys_rsa.hw,
> +	[CLKID_SYS_SAR_ADC]		= &sys_sar_adc.hw,
> +	[CLKID_SYS_STARTUP]		= &sys_startup.hw,
> +	[CLKID_SYS_SECURE]		= &sys_secure.hw,
> +	[CLKID_SYS_SPIFC]		= &sys_spifc.hw,
> +	[CLKID_SYS_DSPA]		= &sys_dspa.hw,
> +	[CLKID_SYS_NNA]			= &sys_nna.hw,
> +	[CLKID_SYS_ETH_MAC]		= &sys_eth_mac.hw,
> +	[CLKID_SYS_GIC]			= &sys_gic.hw,
> +	[CLKID_SYS_RAMA]		= &sys_rama.hw,
> +	[CLKID_SYS_BIG_NIC]		= &sys_big_nic.hw,
> +	[CLKID_SYS_RAMB]		= &sys_ramb.hw,
> +	[CLKID_SYS_AUDIO_TOP]		= &sys_audio_top.hw,
> +	[CLKID_SYS_AUDIO_VAD]		= &sys_audio_vad.hw,
> +	[CLKID_SYS_USB]			= &sys_usb.hw,
> +	[CLKID_SYS_SD_EMMC_A]		= &sys_sd_emmc_a.hw,
> +	[CLKID_SYS_SD_EMMC_C]		= &sys_sd_emmc_c.hw,
> +	[CLKID_SYS_PWM_AB]		= &sys_pwm_ab.hw,
> +	[CLKID_SYS_PWM_CD]		= &sys_pwm_cd.hw,
> +	[CLKID_SYS_PWM_EF]		= &sys_pwm_ef.hw,
> +	[CLKID_SYS_PWM_GH]		= &sys_pwm_gh.hw,
> +	[CLKID_SYS_SPICC_1]		= &sys_spicc_1.hw,
> +	[CLKID_SYS_SPICC_0]		= &sys_spicc_0.hw,
> +	[CLKID_SYS_UART_A]		= &sys_uart_a.hw,
> +	[CLKID_SYS_UART_B]		= &sys_uart_b.hw,
> +	[CLKID_SYS_UART_C]		= &sys_uart_c.hw,
> +	[CLKID_SYS_UART_D]		= &sys_uart_d.hw,
> +	[CLKID_SYS_UART_E]		= &sys_uart_e.hw,
> +	[CLKID_SYS_I2C_M_A]		= &sys_i2c_m_a.hw,
> +	[CLKID_SYS_I2C_M_B]		= &sys_i2c_m_b.hw,
> +	[CLKID_SYS_I2C_M_C]		= &sys_i2c_m_c.hw,
> +	[CLKID_SYS_I2C_M_D]		= &sys_i2c_m_d.hw,
> +	[CLKID_SYS_RTC]			= &sys_rtc.hw,
> +	[CLKID_AXI_AUDIO_VAD]		= &axi_audio_vad.hw,
> +	[CLKID_AXI_AUDIO_TOP]		= &axi_audio_top.hw,
> +	[CLKID_AXI_SYS_NIC]		= &axi_sys_nic.hw,
> +	[CLKID_AXI_RAMB]		= &axi_ramb.hw,
> +	[CLKID_AXI_RAMA]		= &axi_rama.hw,
> +	[CLKID_AXI_CPU_DMC]		= &axi_cpu_dmc.hw,
> +	[CLKID_AXI_NNA]			= &axi_nna.hw,
> +	[CLKID_AXI_DEV1_DMC]		= &axi_dev1_dmc.hw,
> +	[CLKID_AXI_DEV0_DMC]		= &axi_dev0_dmc.hw,
> +	[CLKID_AXI_DSP_DMC]		= &axi_dsp_dmc.hw,
> +	[CLKID_12_24M_IN]		= &clk_12_24m_in.hw,
> +	[CLKID_12M_24M]			= &clk_12_24m.hw,
> +	[CLKID_FCLK_25M_DIV]		= &fclk_25m_div.hw,
> +	[CLKID_FCLK_25M]		= &fclk_25m.hw,
> +	[CLKID_GEN_SEL]			= &gen_sel.hw,
> +	[CLKID_GEN_DIV]			= &gen_div.hw,
> +	[CLKID_GEN]			= &gen.hw,
> +	[CLKID_SARADC_SEL]		= &saradc_sel.hw,
> +	[CLKID_SARADC_DIV]		= &saradc_div.hw,
> +	[CLKID_SARADC]			= &saradc.hw,
> +	[CLKID_PWM_A_SEL]		= &pwm_a_sel.hw,
> +	[CLKID_PWM_A_DIV]		= &pwm_a_div.hw,
> +	[CLKID_PWM_A]			= &pwm_a.hw,
> +	[CLKID_PWM_B_SEL]		= &pwm_b_sel.hw,
> +	[CLKID_PWM_B_DIV]		= &pwm_b_div.hw,
> +	[CLKID_PWM_B]			= &pwm_b.hw,
> +	[CLKID_PWM_C_SEL]		= &pwm_c_sel.hw,
> +	[CLKID_PWM_C_DIV]		= &pwm_c_div.hw,
> +	[CLKID_PWM_C]			= &pwm_c.hw,
> +	[CLKID_PWM_D_SEL]		= &pwm_d_sel.hw,
> +	[CLKID_PWM_D_DIV]		= &pwm_d_div.hw,
> +	[CLKID_PWM_D]			= &pwm_d.hw,
> +	[CLKID_PWM_E_SEL]		= &pwm_e_sel.hw,
> +	[CLKID_PWM_E_DIV]		= &pwm_e_div.hw,
> +	[CLKID_PWM_E]			= &pwm_e.hw,
> +	[CLKID_PWM_F_SEL]		= &pwm_f_sel.hw,
> +	[CLKID_PWM_F_DIV]		= &pwm_f_div.hw,
> +	[CLKID_PWM_F]			= &pwm_f.hw,
> +	[CLKID_PWM_G_SEL]		= &pwm_g_sel.hw,
> +	[CLKID_PWM_G_DIV]		= &pwm_g_div.hw,
> +	[CLKID_PWM_G]			= &pwm_g.hw,
> +	[CLKID_PWM_H_SEL]		= &pwm_h_sel.hw,
> +	[CLKID_PWM_H_DIV]		= &pwm_h_div.hw,
> +	[CLKID_PWM_H]			= &pwm_h.hw,
> +	[CLKID_SPICC_0_SEL]		= &spicc_0_sel.hw,
> +	[CLKID_SPICC_0_DIV]		= &spicc_0_div.hw,
> +	[CLKID_SPICC_0]			= &spicc_0.hw,
> +	[CLKID_SPICC_1_SEL]		= &spicc_1_sel.hw,
> +	[CLKID_SPICC_1_DIV]		= &spicc_1_div.hw,
> +	[CLKID_SPICC_1]			= &spicc_1.hw,
> +	[CLKID_SD_EMMC_A_SEL]		= &sd_emmc_a_sel.hw,
> +	[CLKID_SD_EMMC_A_DIV]		= &sd_emmc_a_div.hw,
> +	[CLKID_SD_EMMC_A]		= &sd_emmc_a.hw,
> +	[CLKID_SD_EMMC_C_SEL]		= &sd_emmc_c_sel.hw,
> +	[CLKID_SD_EMMC_C_DIV]		= &sd_emmc_c_div.hw,
> +	[CLKID_SD_EMMC_C]		= &sd_emmc_c.hw,
> +	[CLKID_TS_DIV]			= &ts_div.hw,
> +	[CLKID_TS]			= &ts.hw,
> +	[CLKID_ETH_125M_DIV]		= &eth_125m_div.hw,
> +	[CLKID_ETH_125M]		= &eth_125m.hw,
> +	[CLKID_ETH_RMII_DIV]		= &eth_rmii_div.hw,
> +	[CLKID_ETH_RMII]		= &eth_rmii.hw,
> +	[CLKID_DSPA_0_SEL]		= &dspa_0_sel.hw,
> +	[CLKID_DSPA_0_DIV]		= &dspa_0_div.hw,
> +	[CLKID_DSPA_0]			= &dspa_0.hw,
> +	[CLKID_DSPA_1_SEL]		= &dspa_1_sel.hw,
> +	[CLKID_DSPA_1_DIV]		= &dspa_1_div.hw,
> +	[CLKID_DSPA_1]			= &dspa_1.hw,
> +	[CLKID_DSPA]			= &dspa.hw,
> +	[CLKID_NNA_CORE_SEL]		= &nna_core_sel.hw,
> +	[CLKID_NNA_CORE_DIV]		= &nna_core_div.hw,
> +	[CLKID_NNA_CORE]		= &nna_core.hw,
> +	[CLKID_NNA_AXI_SEL]		= &nna_axi_sel.hw,
> +	[CLKID_NNA_AXI_DIV]		= &nna_axi_div.hw,
> +	[CLKID_NNA_AXI]			= &nna_axi.hw,
> +};
> +
> +/* Convenience table to populate regmap in .probe */
> +static struct clk_regmap *const a5_periphs_clk_regmaps[] = {
> +	&rtc_xtal_clkin,
> +	&rtc_32k_div,
> +	&rtc_32k_mux,
> +	&rtc_32k,
> +	&rtc_clk,
> +	&sys_reset_ctrl,
> +	&sys_pwr_ctrl,
> +	&sys_pad_ctrl,
> +	&sys_ctrl,
> +	&sys_ts_pll,
> +	&sys_dev_arb,
> +	&sys_mmc_pclk,
> +	&sys_mailbox,
> +	&sys_cpu_ctrl,
> +	&sys_jtag_ctrl,
> +	&sys_ir_ctrl,
> +	&sys_irq_ctrl,
> +	&sys_msr_clk,
> +	&sys_rom,
> +	&sys_cpu_apb,
> +	&sys_rsa,
> +	&sys_sar_adc,
> +	&sys_startup,
> +	&sys_secure,
> +	&sys_spifc,
> +	&sys_dspa,
> +	&sys_nna,
> +	&sys_eth_mac,
> +	&sys_gic,
> +	&sys_rama,
> +	&sys_big_nic,
> +	&sys_ramb,
> +	&sys_audio_top,
> +	&sys_audio_vad,
> +	&sys_usb,
> +	&sys_sd_emmc_a,
> +	&sys_sd_emmc_c,
> +	&sys_pwm_ab,
> +	&sys_pwm_cd,
> +	&sys_pwm_ef,
> +	&sys_pwm_gh,
> +	&sys_spicc_1,
> +	&sys_spicc_0,
> +	&sys_uart_a,
> +	&sys_uart_b,
> +	&sys_uart_c,
> +	&sys_uart_d,
> +	&sys_uart_e,
> +	&sys_i2c_m_a,
> +	&sys_i2c_m_b,
> +	&sys_i2c_m_c,
> +	&sys_i2c_m_d,
> +	&sys_rtc,
> +	&axi_audio_vad,
> +	&axi_audio_top,
> +	&axi_sys_nic,
> +	&axi_ramb,
> +	&axi_rama,
> +	&axi_cpu_dmc,
> +	&axi_nna,
> +	&axi_dev1_dmc,
> +	&axi_dev0_dmc,
> +	&axi_dsp_dmc,
> +	&clk_12_24m_in,
> +	&clk_12_24m,
> +	&fclk_25m_div,
> +	&fclk_25m,
> +	&gen_sel,
> +	&gen_div,
> +	&gen,
> +	&saradc_sel,
> +	&saradc_div,
> +	&saradc,
> +	&pwm_a_sel,
> +	&pwm_a_div,
> +	&pwm_a,
> +	&pwm_b_sel,
> +	&pwm_b_div,
> +	&pwm_b,
> +	&pwm_c_sel,
> +	&pwm_c_div,
> +	&pwm_c,
> +	&pwm_d_sel,
> +	&pwm_d_div,
> +	&pwm_d,
> +	&pwm_e_sel,
> +	&pwm_e_div,
> +	&pwm_e,
> +	&pwm_f_sel,
> +	&pwm_f_div,
> +	&pwm_f,
> +	&pwm_g_sel,
> +	&pwm_g_div,
> +	&pwm_g,
> +	&pwm_h_sel,
> +	&pwm_h_div,
> +	&pwm_h,
> +	&spicc_0_sel,
> +	&spicc_0_div,
> +	&spicc_0,
> +	&spicc_1_sel,
> +	&spicc_1_div,
> +	&spicc_1,
> +	&sd_emmc_a_sel,
> +	&sd_emmc_a_div,
> +	&sd_emmc_a,
> +	&sd_emmc_c_sel,
> +	&sd_emmc_c_div,
> +	&sd_emmc_c,
> +	&ts_div,
> +	&ts,
> +	&eth_125m,
> +	&eth_rmii_div,
> +	&eth_rmii,
> +	&dspa_0_sel,
> +	&dspa_0_div,
> +	&dspa_0,
> +	&dspa_1_sel,
> +	&dspa_1_div,
> +	&dspa_1,
> +	&dspa,
> +	&nna_core_sel,
> +	&nna_core_div,
> +	&nna_core,
> +	&nna_axi_sel,
> +	&nna_axi_div,
> +	&nna_axi
> +};
> +
> +static const struct regmap_config clkc_regmap_config = {
> +	.reg_bits       = 32,
> +	.val_bits       = 32,
> +	.reg_stride     = 4,
> +	.max_register   = CLKCTRL_NNA_CLK_CNTL,
> +};
> +
> +static struct meson_clk_hw_data a5_periphs_clks = {
> +	.hws = a5_periphs_hw_clks,
> +	.num = ARRAY_SIZE(a5_periphs_hw_clks),
> +};
> +
> +static int aml_a5_peripherals_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct regmap *regmap;
> +	void __iomem *base;
> +	int clkid, ret, i;
> +
> +	base = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(base))
> +		return PTR_ERR(base);
> +
> +	regmap = devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
> +	if (IS_ERR(regmap))
> +		return PTR_ERR(regmap);
> +
> +	/* Populate regmap for the regmap backed clocks */
> +	for (i = 0; i < ARRAY_SIZE(a5_periphs_clk_regmaps); i++)
> +		a5_periphs_clk_regmaps[i]->map = regmap;
> +
> +	for (clkid = 0; clkid < a5_periphs_clks.num; clkid++) {
> +		/* array might be sparse */
> +		if (!a5_periphs_clks.hws[clkid])
> +			continue;
> +
> +		ret = devm_clk_hw_register(dev, a5_periphs_clks.hws[clkid]);
> +		if (ret) {
> +			dev_err(dev, "Clock registration failed\n");
> +			return ret;
> +		}
> +	}
> +
> +	return devm_of_clk_add_hw_provider(dev, meson_clk_hw_get,
> +					   &a5_periphs_clks);
> +}
> +
> +static const struct of_device_id a5_peripherals_clkc_match_table[] = {
> +	{
> +		.compatible = "amlogic,a5-peripherals-clkc",
> +	},
> +	{ /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, a5_peripherals_clkc_match_table);
> +
> +static struct platform_driver a5_peripherals_driver = {
> +	.probe		= aml_a5_peripherals_probe,
> +	.driver		= {
> +		.name	= "a5-peripherals-clkc",
> +		.of_match_table = a5_peripherals_clkc_match_table,
> +	},
> +};
> +module_platform_driver(a5_peripherals_driver);
> +
> +MODULE_DESCRIPTION("Amlogic A5 Peripherals Clock Controller driver");
> +MODULE_AUTHOR("Chuan Liu <[e-mail]>");
> +MODULE_LICENSE("GPL");

Xianwei Zhao Sept. 29, 2024, 8:44 a.m. UTC | #2

Hi Jerome,
     Thanks for your reply.

On 2024/9/24 23:09, Jerome Brunet wrote:
> [ EXTERNAL EMAIL ]
> 
> On Sat 14 Sep 2024 at 13:25, Xianwei Zhao via B4 Relay <[e-mail]> wrote:
> 
>> From: Chuan Liu <[e-mail]>
>>
>> Add the peripherals clock controller driver in the A5 SoC family.
>>
>> Signed-off-by: Chuan Liu <[e-mail]>
>> Signed-off-by: Xianwei Zhao <[e-mail]>
>> ---
>>   drivers/clk/meson/Kconfig          |   14 +
>>   drivers/clk/meson/Makefile         |    1 +
>>   drivers/clk/meson/a5-peripherals.c | 1471 ++++++++++++++++++++++++++++++++++++
>>   3 files changed, 1486 insertions(+)
>>
>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>> index 2a713276e46c..21845edcd8ef 100644
>> --- a/drivers/clk/meson/Kconfig
>> +++ b/drivers/clk/meson/Kconfig
>> @@ -146,6 +146,20 @@ config COMMON_CLK_A5_PLL
>>          Say Y if you want the board to work, because PLLs are the parent
>>          of most peripherals.
>>
>> +config COMMON_CLK_A5_PERIPHERALS
>> +     tristate "Amlogic A5 peripherals clock controller"
>> +     depends on ARM64
>> +     default y
>> +     imply ARM_SCMI_PROTOCOL
> 
> same
> 

Will do.

>> +     imply COMMON_CLK_SCMI
>> +     imply COMMON_CLK_A5_PLL
>> +     select COMMON_CLK_MESON_REGMAP
>> +     select COMMON_CLK_MESON_DUALDIV
>> +     select COMMON_CLK_MESON_CLKC_UTILS
>> +     help
>> +       Support for the Peripherals clock controller on Amlogic AV40x device,
>> +       AKA A5. Say Y if you want the peripherals clock to work.
>> +
>>   config COMMON_CLK_C3_PLL
>>        tristate "Amlogic C3 PLL clock controller"
>>        depends on ARM64
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index fc4b8a723145..58236c6e8377 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -21,6 +21,7 @@ obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>>   obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
>>   obj-$(CONFIG_COMMON_CLK_A1_PERIPHERALS) += a1-peripherals.o
>>   obj-$(CONFIG_COMMON_CLK_A5_PLL) += a5-pll.o
>> +obj-$(CONFIG_COMMON_CLK_A5_PERIPHERALS) += a5-peripherals.o
>>   obj-$(CONFIG_COMMON_CLK_C3_PLL) += c3-pll.o
>>   obj-$(CONFIG_COMMON_CLK_C3_PERIPHERALS) += c3-peripherals.o
>>   obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>> diff --git a/drivers/clk/meson/a5-peripherals.c b/drivers/clk/meson/a5-peripherals.c
>> new file mode 100644
>> index 000000000000..c28da340a5af
>> --- /dev/null
>> +++ b/drivers/clk/meson/a5-peripherals.c
>> @@ -0,0 +1,1471 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +/*
>> + * Amlogic A5 Peripherals Clock Controller Driver
>> + *
>> + * Copyright (c) 2024 Amlogic, inc.
>> + * Author: Chuan Liu <[e-mail]>
>> + */
>> +
>> +#include <linux/clk-provider.h>
>> +#include <linux/platform_device.h>
>> +#include "clk-regmap.h"
>> +#include "clk-dualdiv.h"
>> +#include "meson-clkc-utils.h"
>> +#include <dt-bindings/clock/amlogic,a5-peripherals-clkc.h>
>> +
>> +#define CLKCTRL_RTC_BY_OSCIN_CTRL0           0x8
>> +#define CLKCTRL_RTC_BY_OSCIN_CTRL1           0xc
>> +#define CLKCTRL_RTC_CTRL                     0x10
>> +#define CLKCTRL_SYS_CLK_EN0_REG0             0x44
>> +#define CLKCTRL_SYS_CLK_EN0_REG1             0x48
>> +#define CLKCTRL_DSPA_CLK_CTRL0                       0x9c
>> +#define CLKCTRL_CLK12_24_CTRL                        0xa8
>> +#define CLKCTRL_AXI_CLK_EN0                  0xac
>> +#define CLKCTRL_TS_CLK_CTRL                  0x158
>> +#define CLKCTRL_ETH_CLK_CTRL                 0x164
>> +#define CLKCTRL_NAND_CLK_CTRL                        0x168
>> +#define CLKCTRL_SD_EMMC_CLK_CTRL             0x16c
>> +#define CLKCTRL_SPICC_CLK_CTRL                       0x174
>> +#define CLKCTRL_GEN_CLK_CTRL                 0x178
>> +#define CLKCTRL_SAR_CLK_CTRL0                        0x17c
>> +#define CLKCTRL_PWM_CLK_AB_CTRL                      0x180
>> +#define CLKCTRL_PWM_CLK_CD_CTRL                      0x184
>> +#define CLKCTRL_PWM_CLK_EF_CTRL                      0x188
>> +#define CLKCTRL_PWM_CLK_GH_CTRL                      0x18c
>> +#define CLKCTRL_NNA_CLK_CNTL                 0x220
> 
> Again I see a lot of holes in there. Please make sure there is only
> clocks in the whole region you are claiming for the device.
> 
> Otherwise it is fine to register as many controller as necessary
> 

This has been verified to not overlap the register fields of other 
controllers.

>> +
>> +static struct clk_regmap rtc_xtal_clkin = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_RTC_BY_OSCIN_CTRL0,
>> +             .bit_idx = 31,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "rtc_xtal_clkin",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_data = &(const struct clk_parent_data) {
>> +                     .fw_name = "oscin",
>> +             },
>> +             .num_parents = 1,
>> +     },
>> +};
>> +
>> +static const struct meson_clk_dualdiv_param rtc_32k_div_table[] = {
>> +     { 733, 732, 8, 11, 1 },
>> +     { /* sentinel */ }
>> +};
>> +
>> +static struct clk_regmap rtc_32k_div = {
>> +     .data = &(struct meson_clk_dualdiv_data) {
>> +             .n1 = {
>> +                     .reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL0,
>> +                     .shift   = 0,
>> +                     .width   = 12,
>> +             },
>> +             .n2 = {
>> +                     .reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL0,
>> +                     .shift   = 12,
>> +                     .width   = 12,
>> +             },
>> +             .m1 = {
>> +                     .reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL1,
>> +                     .shift   = 0,
>> +                     .width   = 12,
>> +             },
>> +             .m2 = {
>> +                     .reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL1,
>> +                     .shift   = 12,
>> +                     .width   = 12,
>> +             },
>> +             .dual = {
>> +                     .reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL0,
>> +                     .shift   = 28,
>> +                     .width   = 1,
>> +             },
>> +             .table = rtc_32k_div_table,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "rtc_32k_div",
>> +             .ops = &meson_clk_dualdiv_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &rtc_xtal_clkin.hw
>> +             },
>> +             .num_parents = 1,
>> +     },
>> +};
>> +
>> +static const struct clk_parent_data rtc_32k_mux_parent_data[] = {
>> +     { .hw = &rtc_32k_div.hw },
>> +     { .hw = &rtc_xtal_clkin.hw }
>> +};
>> +
>> +static struct clk_regmap rtc_32k_mux = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_RTC_BY_OSCIN_CTRL1,
>> +             .mask = 0x1,
>> +             .shift = 24,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "rtc_32k_mux",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = rtc_32k_mux_parent_data,
>> +             .num_parents = ARRAY_SIZE(rtc_32k_mux_parent_data),
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap rtc_32k = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_RTC_BY_OSCIN_CTRL0,
>> +             .bit_idx = 30,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "rtc_32k",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &rtc_32k_mux.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static const struct clk_parent_data rtc_clk_mux_parent_data[] = {
>> +     { .fw_name = "oscin" },
>> +     { .hw = &rtc_32k.hw },
>> +     { .fw_name = "pad_osc" }
>> +};
>> +
>> +static struct clk_regmap rtc_clk = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_RTC_CTRL,
>> +             .mask = 0x3,
>> +             .shift = 0,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "rtc_clk",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = rtc_clk_mux_parent_data,
>> +             .num_parents = ARRAY_SIZE(rtc_clk_mux_parent_data),
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +#define A4_CLK_GATE(_name, _reg, _bit, _fw_name, _ops, _flags)
>> \
> 
> A4 ??? everything else is A5 ? Please explain
> 
This is a mistake. Will define macro in common head file.

>> +struct clk_regmap _name = {                                          \
>> +     .data = &(struct clk_regmap_gate_data){                         \
>> +             .offset = (_reg),                                       \
>> +             .bit_idx = (_bit),                                      \
>> +     },                                                              \
>> +     .hw.init = &(struct clk_init_data) {                            \
>> +             .name = #_name,                                         \
>> +             .ops = _ops,                                            \
>> +             .parent_data = &(const struct clk_parent_data) {        \
>> +                     .fw_name = #_fw_name,                           \
>> +             },                                                      \
>> +             .num_parents = 1,                                       \
>> +             .flags = (_flags),                                      \
>> +     },                                                              \
>> +}
>> +
>> +#define A4_SYS_GATE(_name, _reg, _bit, _flags)                               \
>> +     A4_CLK_GATE(_name, _reg, _bit, sysclk,                          \
>> +                 &clk_regmap_gate_ops, _flags)
>> +
>> +#define A4_SYS_GATE_RO(_name, _reg, _bit)                            \
>> +     A4_CLK_GATE(_name, _reg, _bit, sysclk,                          \
>> +                 &clk_regmap_gate_ro_ops, 0)
> 
> Looks like a copy/paste of the C3. If this pattern keeps on repeating,
> it would be nice to make a common definition
>

Will do.

>> +
>> +static A4_SYS_GATE(sys_reset_ctrl,   CLKCTRL_SYS_CLK_EN0_REG0, 1, 0);
>> +static A4_SYS_GATE(sys_pwr_ctrl,     CLKCTRL_SYS_CLK_EN0_REG0, 3, 0);
>> +static A4_SYS_GATE(sys_pad_ctrl,     CLKCTRL_SYS_CLK_EN0_REG0, 4, 0);
>> +static A4_SYS_GATE(sys_ctrl,         CLKCTRL_SYS_CLK_EN0_REG0, 5, 0);
>> +static A4_SYS_GATE(sys_ts_pll,               CLKCTRL_SYS_CLK_EN0_REG0, 6, 0);
>> +
>> +/*
>> + * NOTE: sys_dev_arb provides the clock to the ETH and SPICC arbiters that
>> + * access the AXI bus.
>> + */
>> +static A4_SYS_GATE(sys_dev_arb,              CLKCTRL_SYS_CLK_EN0_REG0, 7, 0);
>> +
>> +/*
>> + * FIXME: sys_mmc_pclk provides the clock for the DDR PHY, DDR will only be
>> + * initialized in bl2, and this clock should not be touched in linux.
>> + */
>> +static A4_SYS_GATE_RO(sys_mmc_pclk,  CLKCTRL_SYS_CLK_EN0_REG0, 8);
>> +static A4_SYS_GATE(sys_mailbox,              CLKCTRL_SYS_CLK_EN0_REG0, 10, 0);
>> +
>> +/*
>> + * NOTE: sys_cpu_ctrl provides the clock for CPU controller. After clock is
>> + * disabled, cpu_clk and other key CPU-related configurations cannot take effect.
>> + */
>> +static A4_SYS_GATE(sys_cpu_ctrl,     CLKCTRL_SYS_CLK_EN0_REG0, 11, CLK_IS_CRITICAL);
>> +static A4_SYS_GATE(sys_jtag_ctrl,    CLKCTRL_SYS_CLK_EN0_REG0, 12, 0);
>> +static A4_SYS_GATE(sys_ir_ctrl,              CLKCTRL_SYS_CLK_EN0_REG0, 13, 0);
>> +
>> +/*
>> + * NOTE: sys_irq_ctrl provides the clock for IRQ controller. The IRQ controller
>> + * collects and distributes the interrupt signal to the GIC, PWR_CTRL, and
>> + * AOCPU. If the clock is disabled, interrupt-related functions will occurs an
>> + * exception.
>> + */
>> +static A4_SYS_GATE(sys_irq_ctrl,     CLKCTRL_SYS_CLK_EN0_REG0, 14, CLK_IS_CRITICAL);
>> +static A4_SYS_GATE(sys_msr_clk,              CLKCTRL_SYS_CLK_EN0_REG0, 15, 0);
>> +static A4_SYS_GATE(sys_rom,          CLKCTRL_SYS_CLK_EN0_REG0, 16, 0);
>> +static A4_SYS_GATE(sys_cpu_apb,              CLKCTRL_SYS_CLK_EN0_REG0, 18, 0);
>> +static A4_SYS_GATE(sys_rsa,          CLKCTRL_SYS_CLK_EN0_REG0, 19, 0);
>> +static A4_SYS_GATE(sys_sar_adc,              CLKCTRL_SYS_CLK_EN0_REG0, 20, 0);
>> +static A4_SYS_GATE(sys_startup,              CLKCTRL_SYS_CLK_EN0_REG0, 21, 0);
>> +static A4_SYS_GATE(sys_secure,               CLKCTRL_SYS_CLK_EN0_REG0, 22, 0);
>> +static A4_SYS_GATE(sys_spifc,                CLKCTRL_SYS_CLK_EN0_REG0, 23, 0);
>> +static A4_SYS_GATE(sys_dspa,         CLKCTRL_SYS_CLK_EN0_REG0, 24, 0);
>> +static A4_SYS_GATE(sys_nna,          CLKCTRL_SYS_CLK_EN0_REG0, 25, 0);
>> +static A4_SYS_GATE(sys_eth_mac,              CLKCTRL_SYS_CLK_EN0_REG0, 26, 0);
>> +
>> +/*
>> + * FIXME: sys_gic provides the clock for GIC(Generic Interrupt Controller).
>> + * After clock is disabled, The GIC cannot work properly. At present, the driver
>> + * used by our GIC is the public driver in kernel, and there is no management
>> + * clock in the driver.
>> + */
>> +static A4_SYS_GATE(sys_gic,          CLKCTRL_SYS_CLK_EN0_REG0, 27, CLK_IS_CRITICAL);
> 
> The GIC has a driver. If it needs clock, maybe it should request it and
> enable it, maybe as optional.
> 

This has been explained in C3. GIC is a public driver that does not 
reference clock, so you suggest setting it as CRITICAL and adding the
"FIXME" annotation.

>> +static A4_SYS_GATE(sys_rama,         CLKCTRL_SYS_CLK_EN0_REG0, 28, 0);
>> +
>> +/*
>> + * NOTE: sys_big_nic provides the clock to the control bus of the NIC(Network
>> + * Interface Controller) between multiple devices(CPU, DDR, RAM, ROM, GIC,
>> + * SPIFC, CAPU, JTAG, EMMC, SDIO, sec_top, USB, Audio, ETH, SPICC) in the
>> + * system. After clock is disabled, The NIC cannot work.
>> + */
> 
> This comment looks like a clock that should be passed as ressource to a
> bus or power-domain to be properly manage. This is a pattern that keeps
> on repeating. I will not block you on it this time around but I strong
> suggest you fix up the situation on the related platform. Next time
> around, the reason won't be a valid one.
> 

There are too many modules associated with this clock... The most 
important is the inclusion of some system-level modules that are not 
managed by the driver in the kernel and cannot close their clocks, 
perhaps it is not appropriate to describe it here.

In the next version I moved it to scmi-clk for management?

>> +static A4_SYS_GATE(sys_big_nic,              CLKCTRL_SYS_CLK_EN0_REG0, 29, CLK_IS_CRITICAL);
>> +static A4_SYS_GATE(sys_ramb,         CLKCTRL_SYS_CLK_EN0_REG0, 30, 0);
>> +static A4_SYS_GATE(sys_audio_top,    CLKCTRL_SYS_CLK_EN0_REG1, 0, 0);
>> +static A4_SYS_GATE(sys_audio_vad,    CLKCTRL_SYS_CLK_EN0_REG1, 1, 0);
>> +static A4_SYS_GATE(sys_usb,          CLKCTRL_SYS_CLK_EN0_REG1, 2, 0);
>> +static A4_SYS_GATE(sys_sd_emmc_a,    CLKCTRL_SYS_CLK_EN0_REG1, 3, 0);
>> +static A4_SYS_GATE(sys_sd_emmc_c,    CLKCTRL_SYS_CLK_EN0_REG1, 4, 0);
>> +static A4_SYS_GATE(sys_pwm_ab,               CLKCTRL_SYS_CLK_EN0_REG1, 5, 0);
>> +static A4_SYS_GATE(sys_pwm_cd,               CLKCTRL_SYS_CLK_EN0_REG1, 6, 0);
>> +static A4_SYS_GATE(sys_pwm_ef,               CLKCTRL_SYS_CLK_EN0_REG1, 7, 0);
>> +static A4_SYS_GATE(sys_pwm_gh,               CLKCTRL_SYS_CLK_EN0_REG1, 8, 0);
>> +static A4_SYS_GATE(sys_spicc_1,              CLKCTRL_SYS_CLK_EN0_REG1, 9, 0);
>> +static A4_SYS_GATE(sys_spicc_0,              CLKCTRL_SYS_CLK_EN0_REG1, 10, 0);
>> +static A4_SYS_GATE(sys_uart_a,               CLKCTRL_SYS_CLK_EN0_REG1, 11, 0);
>> +static A4_SYS_GATE(sys_uart_b,               CLKCTRL_SYS_CLK_EN0_REG1, 12, 0);
>> +static A4_SYS_GATE(sys_uart_c,               CLKCTRL_SYS_CLK_EN0_REG1, 13, 0);
>> +static A4_SYS_GATE(sys_uart_d,               CLKCTRL_SYS_CLK_EN0_REG1, 14, 0);
>> +static A4_SYS_GATE(sys_uart_e,               CLKCTRL_SYS_CLK_EN0_REG1, 15, 0);
>> +static A4_SYS_GATE(sys_i2c_m_a,              CLKCTRL_SYS_CLK_EN0_REG1, 16, 0);
>> +static A4_SYS_GATE(sys_i2c_m_b,              CLKCTRL_SYS_CLK_EN0_REG1, 17, 0);
>> +static A4_SYS_GATE(sys_i2c_m_c,              CLKCTRL_SYS_CLK_EN0_REG1, 18, 0);
>> +static A4_SYS_GATE(sys_i2c_m_d,              CLKCTRL_SYS_CLK_EN0_REG1, 19, 0);
>> +static A4_SYS_GATE(sys_rtc,          CLKCTRL_SYS_CLK_EN0_REG1, 21, 0);
>> +
>> +#define A4_AXI_GATE(_name, _reg, _bit, _flags)                               \
>> +     A4_CLK_GATE(_name, _reg, _bit, axiclk,                          \
>> +                 &clk_regmap_gate_ops, _flags)
>> +
>> +static A4_AXI_GATE(axi_audio_vad,    CLKCTRL_AXI_CLK_EN0, 0, 0);
>> +static A4_AXI_GATE(axi_audio_top,    CLKCTRL_AXI_CLK_EN0, 1, 0);
>> +
>> +/*
>> + * NOTE: axi_sys_nic provides the clock to the AXI bus of the system NIC. After
>> + * clock is disabled, The NIC cannot work.
>> + */
>> +static A4_AXI_GATE(axi_sys_nic,              CLKCTRL_AXI_CLK_EN0, 2, CLK_IS_CRITICAL);
>> +static A4_AXI_GATE(axi_ramb,         CLKCTRL_AXI_CLK_EN0, 5, 0);
>> +static A4_AXI_GATE(axi_rama,         CLKCTRL_AXI_CLK_EN0, 6, 0);
>> +
>> +/*
>> + * NOTE: axi_cpu_dmc provides the clock to the AXI bus where the CPU accesses
>> + * the DDR. After clock is disabled, The CPU will not have access to the DDR.
>> + */
>> +static A4_AXI_GATE(axi_cpu_dmc,              CLKCTRL_AXI_CLK_EN0, 7, CLK_IS_CRITICAL);
>> +static A4_AXI_GATE(axi_nna,          CLKCTRL_AXI_CLK_EN0, 12, 0);
>> +
>> +/*
>> + * NOTE: axi_dev1_dmc provides the clock for the peripherals(EMMC, SDIO,
>> + * sec_top, USB, Audio) to access the AXI bus of the DDR.
>> + */
> 
> Same.
> 

These normal peripheral drivers manage the clock without a problem.

>> +static A4_AXI_GATE(axi_dev1_dmc,     CLKCTRL_AXI_CLK_EN0, 13, 0);
>> +
>> +/*
>> + * NOTE: axi_dev0_dmc provides the clock for the peripherals(ETH and SPICC)
>> + * to access the AXI bus of the DDR.
>> + */
>> +static A4_AXI_GATE(axi_dev0_dmc,     CLKCTRL_AXI_CLK_EN0, 14, 0);
>> +static A4_AXI_GATE(axi_dsp_dmc,              CLKCTRL_AXI_CLK_EN0, 15, 0);
>> +
>> +static struct clk_regmap clk_12_24m_in = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>> +             .bit_idx = 11,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "clk_12_24m_in",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_data = &(const struct clk_parent_data) {
>> +                     .fw_name = "xtal_24m",
>> +             },
>> +             .num_parents = 1,
>> +     },
>> +};
>> +
>> +static struct clk_regmap clk_12_24m = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>> +             .shift = 10,
>> +             .width = 1,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "clk_12_24m",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &clk_12_24m_in.hw
>> +             },
>> +             .num_parents = 1,
>> +     },
>> +};
>> +
>> +/* FIXME: set value 0 will div by 2 like value 1 */
> 
> Again, it is fine when it happens once, like the c3.
> When the pattern starts repeating, it is time to do something about it.
> 

The corresponding suggestions have been made to the hardware designer, 
but now the designed chip cannot be repaired.

>> +static struct clk_regmap fclk_25m_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>> +             .shift = 0,
>> +             .width = 8,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "fclk_25m_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_data = &(const struct clk_parent_data) {
>> +                     .fw_name = "fix",
>> +             },
>> +             .num_parents = 1,
>> +     },
>> +};
>> +
>> +static struct clk_regmap fclk_25m = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>> +             .bit_idx = 12,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "fclk_25m",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &fclk_25m_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +/*
>> + * Channel 3(ddr_dpll_pt_clk) is manged by the DDR module; channel 12(cts_msr_clk)
>> + * is manged by clock measures module. Their hardware are out of clock tree.
> 
> Yet, they exist and should be part of the bindings since they are
> obviously input to this clock.
> 

Will add it to bindings, as optional input clock source.

>> + * Channel 4 5 8 9 10 11 13 14 15 16 18 are not connected.
>> + *
>> + * gp1 is designed for DSU (DynamIQ Shared Unit) alone. It cannot be changed
>> + * arbitrarily. gp1 is read-only in the kernel and is only open for debug purposes.
>> + */
>> +static u32 gen_parent_table[] = { 0, 1, 2, 6, 7, 17, 19, 20, 21, 22, 23, 24, 25,
>> +                               26, 27, 28};
>> +
>> +static const struct clk_parent_data gen_parent_data[] = {
>> +     { .fw_name = "oscin" },
>> +     { .hw = &rtc_clk.hw },
>> +     { .fw_name = "sysplldiv16" },
>> +     { .fw_name = "gp1" },
>> +     { .fw_name = "hifi" },
>> +     { .fw_name = "cpudiv16" },
>> +     { .fw_name = "fdiv2" },
>> +     { .fw_name = "fdiv2p5" },
>> +     { .fw_name = "fdiv3" },
>> +     { .fw_name = "fdiv4" },
>> +     { .fw_name = "fdiv5" },
>> +     { .fw_name = "fdiv7" },
>> +     { .fw_name = "mpll0" },
>> +     { .fw_name = "mpll1" },
>> +     { .fw_name = "mpll2" },
>> +     { .fw_name = "mpll3" }
>> +};
>> +
>> +static struct clk_regmap gen_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_GEN_CLK_CTRL,
>> +             .mask = 0x1f,
>> +             .shift = 12,
>> +             .table = gen_parent_table,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "gen_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = gen_parent_data,
>> +             .num_parents = ARRAY_SIZE(gen_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap gen_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_GEN_CLK_CTRL,
>> +             .shift = 0,
>> +             .width = 11,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "gen_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &gen_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap gen = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_GEN_CLK_CTRL,
>> +             .bit_idx = 11,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "gen",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &gen_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static const struct clk_parent_data saradc_parent_data[] = {
>> +     { .fw_name = "oscin" },
>> +     { .fw_name = "sysclk" }
>> +};
>> +
>> +static struct clk_regmap saradc_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_SAR_CLK_CTRL0,
>> +             .mask = 0x1,
>> +             .shift = 9,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "saradc_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = saradc_parent_data,
>> +             .num_parents = ARRAY_SIZE(saradc_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap saradc_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_SAR_CLK_CTRL0,
>> +             .shift = 0,
>> +             .width = 8,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "saradc_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &saradc_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap saradc = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_SAR_CLK_CTRL0,
>> +             .bit_idx = 8,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "saradc",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &saradc_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static const struct clk_parent_data pwm_parent_data[] = {
>> +     { .fw_name = "oscin" },
>> +     { .hw = &rtc_clk.hw },
>> +     { .fw_name = "fdiv4" },
>> +     { .fw_name = "fdiv3" }
>> +};
>> +
>> +#define AML_PWM_CLK_MUX(_name, _reg, _shift) {                       \
>> +     .data = &(struct clk_regmap_mux_data) {                 \
>> +             .offset = _reg,                                 \
>> +             .mask = 0x3,                                    \
>> +             .shift = _shift,                                \
>> +     },                                                      \
>> +     .hw.init = &(struct clk_init_data) {                    \
>> +             .name = #_name "_sel",                          \
>> +             .ops = &clk_regmap_mux_ops,                     \
>> +             .parent_data = pwm_parent_data,                 \
>> +             .num_parents = ARRAY_SIZE(pwm_parent_data),     \
>> +     },                                                      \
>> +}
>> +
>> +#define AML_PWM_CLK_DIV(_name, _reg, _shift) {                       \
>> +     .data = &(struct clk_regmap_div_data) {                 \
>> +             .offset = _reg,                                 \
>> +             .shift = _shift,                                \
>> +             .width = 8,                                     \
>> +     },                                                      \
>> +     .hw.init = &(struct clk_init_data) {                    \
>> +             .name = #_name "_div",                          \
>> +             .ops = &clk_regmap_divider_ops,                 \
>> +             .parent_names = (const char *[]) { #_name "_sel" },\
>> +             .num_parents = 1,                               \
>> +             .flags = CLK_SET_RATE_PARENT,                   \
>> +     },                                                      \
>> +}
>> +
>> +#define AML_PWM_CLK_GATE(_name, _reg, _bit) {                        \
>> +     .data = &(struct clk_regmap_gate_data) {                \
>> +             .offset = _reg,                                 \
>> +             .bit_idx = _bit,                                \
>> +     },                                                      \
>> +     .hw.init = &(struct clk_init_data) {                    \
>> +             .name = #_name,                                 \
>> +             .ops = &clk_regmap_gate_ops,                    \
>> +             .parent_names = (const char *[]) { #_name "_div" },\
>> +             .num_parents = 1,                               \
>> +             .flags = CLK_SET_RATE_PARENT,                   \
>> +     },                                                      \
>> +}
> 
> Now the prefix is just AML ? please be consistent
> And again, looks like a repeating pattern of these families you've been
> upstreaming lately.
> 

Will do.

>> +
>> +static struct clk_regmap pwm_a_sel =
>> +     AML_PWM_CLK_MUX(pwm_a, CLKCTRL_PWM_CLK_AB_CTRL, 9);
>> +static struct clk_regmap pwm_a_div =
>> +     AML_PWM_CLK_DIV(pwm_a, CLKCTRL_PWM_CLK_AB_CTRL, 0);
>> +static struct clk_regmap pwm_a =
>> +     AML_PWM_CLK_GATE(pwm_a, CLKCTRL_PWM_CLK_AB_CTRL, 8);
>> +
>> +static struct clk_regmap pwm_b_sel =
>> +     AML_PWM_CLK_MUX(pwm_b, CLKCTRL_PWM_CLK_AB_CTRL, 25);
>> +static struct clk_regmap pwm_b_div =
>> +     AML_PWM_CLK_DIV(pwm_b, CLKCTRL_PWM_CLK_AB_CTRL, 16);
>> +static struct clk_regmap pwm_b =
>> +     AML_PWM_CLK_GATE(pwm_b, CLKCTRL_PWM_CLK_AB_CTRL, 24);
>> +
>> +static struct clk_regmap pwm_c_sel =
>> +     AML_PWM_CLK_MUX(pwm_c, CLKCTRL_PWM_CLK_CD_CTRL, 9);
>> +static struct clk_regmap pwm_c_div =
>> +     AML_PWM_CLK_DIV(pwm_c, CLKCTRL_PWM_CLK_CD_CTRL, 0);
>> +static struct clk_regmap pwm_c =
>> +     AML_PWM_CLK_GATE(pwm_c, CLKCTRL_PWM_CLK_CD_CTRL, 8);
>> +
>> +static struct clk_regmap pwm_d_sel =
>> +     AML_PWM_CLK_MUX(pwm_d, CLKCTRL_PWM_CLK_CD_CTRL, 25);
>> +static struct clk_regmap pwm_d_div =
>> +     AML_PWM_CLK_DIV(pwm_d, CLKCTRL_PWM_CLK_CD_CTRL, 16);
>> +static struct clk_regmap pwm_d =
>> +     AML_PWM_CLK_GATE(pwm_d, CLKCTRL_PWM_CLK_CD_CTRL, 24);
>> +
>> +static struct clk_regmap pwm_e_sel =
>> +     AML_PWM_CLK_MUX(pwm_e, CLKCTRL_PWM_CLK_EF_CTRL, 9);
>> +static struct clk_regmap pwm_e_div =
>> +     AML_PWM_CLK_DIV(pwm_e, CLKCTRL_PWM_CLK_EF_CTRL, 0);
>> +static struct clk_regmap pwm_e =
>> +     AML_PWM_CLK_GATE(pwm_e, CLKCTRL_PWM_CLK_EF_CTRL, 8);
>> +
>> +static struct clk_regmap pwm_f_sel =
>> +     AML_PWM_CLK_MUX(pwm_f, CLKCTRL_PWM_CLK_EF_CTRL, 25);
>> +static struct clk_regmap pwm_f_div =
>> +     AML_PWM_CLK_DIV(pwm_f, CLKCTRL_PWM_CLK_EF_CTRL, 16);
>> +static struct clk_regmap pwm_f =
>> +     AML_PWM_CLK_GATE(pwm_f, CLKCTRL_PWM_CLK_EF_CTRL, 24);
>> +
>> +static struct clk_regmap pwm_g_sel =
>> +     AML_PWM_CLK_MUX(pwm_g, CLKCTRL_PWM_CLK_GH_CTRL, 9);
>> +static struct clk_regmap pwm_g_div =
>> +     AML_PWM_CLK_DIV(pwm_g, CLKCTRL_PWM_CLK_GH_CTRL, 0);
>> +static struct clk_regmap pwm_g =
>> +     AML_PWM_CLK_GATE(pwm_g, CLKCTRL_PWM_CLK_GH_CTRL, 8);
>> +
>> +static struct clk_regmap pwm_h_sel =
>> +     AML_PWM_CLK_MUX(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 25);
>> +static struct clk_regmap pwm_h_div =
>> +     AML_PWM_CLK_DIV(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 16);
>> +static struct clk_regmap pwm_h =
>> +     AML_PWM_CLK_GATE(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 24);
>> +
>> +/* Channel 7 is gp1. */
> 
> and ? if GP1 is RO, why can't you add it here ?
> 

gp1_pll is a special clock for DSU, it is integrated into dsu_clk, we
don't want other modules to reference it.

My understanding is that gp1_pll should not be provided to the peripheral
clock tree, perhaps this is a redundant design.

>> +static const struct clk_parent_data spicc_parent_data[] = {
>> +     { .fw_name = "oscin" },
>> +     { .fw_name = "sysclk" },
>> +     { .fw_name = "fdiv4" },
>> +     { .fw_name = "fdiv3" },
>> +     { .fw_name = "fdiv2" },
>> +     { .fw_name = "fdiv5" },
>> +     { .fw_name = "fdiv7" }
>> +};
>> +
>> +static struct clk_regmap spicc_0_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_SPICC_CLK_CTRL,
>> +             .mask = 0x7,
>> +             .shift = 7,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "spicc_0_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = spicc_parent_data,
>> +             .num_parents = ARRAY_SIZE(spicc_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap spicc_0_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_SPICC_CLK_CTRL,
>> +             .shift = 0,
>> +             .width = 6,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "spicc_0_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &spicc_0_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap spicc_0 = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_SPICC_CLK_CTRL,
>> +             .bit_idx = 6,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "spicc_0",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &spicc_0_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap spicc_1_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_SPICC_CLK_CTRL,
>> +             .mask = 0x7,
>> +             .shift = 23,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "spicc_1_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = spicc_parent_data,
>> +             .num_parents = ARRAY_SIZE(spicc_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap spicc_1_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_SPICC_CLK_CTRL,
>> +             .shift = 16,
>> +             .width = 6,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "spicc_1_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &spicc_1_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap spicc_1 = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_SPICC_CLK_CTRL,
>> +             .bit_idx = 22,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "spicc_1",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &spicc_1_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static const struct clk_parent_data emmc_parent_data[] = {
>> +     { .fw_name = "oscin" },
>> +     { .fw_name = "fdiv2" },
>> +     { .fw_name = "fdiv3" },
>> +     { .fw_name = "hifi" },
>> +     { .fw_name = "fdiv2p5" },
>> +     { .fw_name = "mpll2" },
>> +     { .fw_name = "mpll3" },
>> +     { .fw_name = "gp0" }
>> +};
>> +
>> +static struct clk_regmap sd_emmc_a_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_SD_EMMC_CLK_CTRL,
>> +             .mask = 0x7,
>> +             .shift = 9,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "sd_emmc_a_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = emmc_parent_data,
>> +             .num_parents = ARRAY_SIZE(emmc_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap sd_emmc_a_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_SD_EMMC_CLK_CTRL,
>> +             .shift = 0,
>> +             .width = 7,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "sd_emmc_a_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &sd_emmc_a_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap sd_emmc_a = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_SD_EMMC_CLK_CTRL,
>> +             .bit_idx = 7,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "sd_emmc_a",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &sd_emmc_a_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap sd_emmc_c_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_NAND_CLK_CTRL,
>> +             .mask = 0x7,
>> +             .shift = 9,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "sd_emmc_c_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = emmc_parent_data,
>> +             .num_parents = ARRAY_SIZE(emmc_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap sd_emmc_c_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_NAND_CLK_CTRL,
>> +             .shift = 0,
>> +             .width = 7,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "sd_emmc_c_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &sd_emmc_c_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap sd_emmc_c = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_NAND_CLK_CTRL,
>> +             .bit_idx = 7,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "sd_emmc_c",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &sd_emmc_c_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap ts_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_TS_CLK_CTRL,
>> +             .shift = 0,
>> +             .width = 8,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "ts_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_data = &(const struct clk_parent_data) {
>> +                     .fw_name = "oscin",
>> +             },
>> +             .num_parents = 1,
>> +     },
>> +};
>> +
>> +static struct clk_regmap ts = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_TS_CLK_CTRL,
>> +             .bit_idx = 8,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "ts",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &ts_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_fixed_factor eth_125m_div = {
>> +     .mult = 1,
>> +     .div = 8,
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "eth_125m_div",
>> +             .ops = &clk_fixed_factor_ops,
>> +             .parent_data = &(const struct clk_parent_data) {
>> +                     .fw_name = "fdiv2",
>> +             },
>> +             .num_parents = 1,
>> +     },
>> +};
>> +
>> +static struct clk_regmap eth_125m = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_ETH_CLK_CTRL,
>> +             .bit_idx = 7,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "eth_125m",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &eth_125m_div.hw
>> +             },
>> +             .num_parents = 1,
>> +     },
>> +};
>> +
>> +static struct clk_regmap eth_rmii_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_ETH_CLK_CTRL,
>> +             .shift = 0,
>> +             .width = 7,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "eth_rmii_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_data = &(const struct clk_parent_data) {
>> +                     .fw_name = "fdiv2",
>> +             },
>> +             .num_parents = 1,
>> +     },
>> +};
>> +
>> +static struct clk_regmap eth_rmii = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_ETH_CLK_CTRL,
>> +             .bit_idx = 8,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "eth_rmii",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &eth_rmii_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +/* Channel 6 is gp1. */
> 
> same
> 

gp1_pll is a special clock for DSU, it is integrated into dsu_clk, we
don't want other modules to reference it.

My understanding is that gp1_pll should not be provided to the peripheral
clock tree, perhaps this is a redundant design.

>> +static u32 dspa_parent_table[] = { 0, 1, 2, 3, 4, 5, 7};
>> +
>> +static const struct clk_parent_data dspa_parent_data[] = {
>> +     { .fw_name = "oscin" },
>> +     { .fw_name = "fdiv2p5" },
>> +     { .fw_name = "fdiv3" },
>> +     { .fw_name = "rtc" },
>> +     { .fw_name = "hifi" },
>> +     { .fw_name = "fdiv4" },
>> +     { .hw = &rtc_clk.hw }
>> +};
>> +
>> +static struct clk_regmap dspa_0_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>> +             .mask = 0x7,
>> +             .shift = 10,
>> +             .table = dspa_parent_table,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "dspa_0_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = dspa_parent_data,
>> +             .num_parents = ARRAY_SIZE(dspa_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap dspa_0_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>> +             .shift = 0,
>> +             .width = 10,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "dspa_0_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &dspa_0_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap dspa_0 = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>> +             .bit_idx = 13,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "dspa_0",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &dspa_0_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap dspa_1_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>> +             .mask = 0x7,
>> +             .shift = 26,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "dspa_1_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = dspa_parent_data,
>> +             .num_parents = ARRAY_SIZE(dspa_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap dspa_1_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>> +             .shift = 16,
>> +             .width = 10,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "dspa_1_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &dspa_1_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap dspa_1 = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>> +             .bit_idx = 29,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "dspa_1",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &dspa_1_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,
> 
> A word about SET_RATE_GATE ?
> 

Look at the response to one of the questions below.

>> +     },
>> +};
>> +
>> +static struct clk_regmap dspa = {
>> +     .data = &(struct clk_regmap_mux_data){
>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>> +             .mask = 0x1,
>> +             .shift = 15,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "dspa",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &dspa_0.hw,
>> +                     &dspa_1.hw
>> +             },
>> +             .num_parents = 2,
>> +             /*
>> +              * NOTE: This level of mux is "no glitch mux", and mux_0
>> +              * (here dspa_0) is not only the clock source for mux, but also
>> +              * provides a working clock for "no glitch mux". "no glitch mux"
>> +              * can be switched only when mux_0 has a clock input. Therefore,
>> +              * add flag CLK_OPS_PARENT_ENABLE to ensure that mux_0 has clock
>> +              * when "no glitch mux" works.
>> +              */
>> +             .flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
> 
> Humm CLK_OPS_PARENT_ENABLE is not how we have handling glitch free mux
> so far. What changed ?
> 

This is a hidden problem we have discovered in recent years, the 
previous chip use is ping-pong switching "no-glitch-mux/glitch free" 
have this problem. If mux_0 does not have a clock "no-glitch-mux", it 
will not be able to switch channels, and I will organize and submit 
patch to fix it later.

>> +     },
>> +};
>> +
>> +/* Channel 6 is gp1. */
>> +static u32 nna_parent_table[] = { 0, 1, 2, 3, 4, 5, 7};
>> +
>> +static const struct clk_parent_data nna_parent_data[] = {
>> +     { .fw_name = "oscin" },
>> +     { .fw_name = "fdiv2p5" },
>> +     { .fw_name = "fdiv4" },
>> +     { .fw_name = "fdiv3" },
>> +     { .fw_name = "fdiv5" },
>> +     { .fw_name = "fdiv2" },
>> +     { .fw_name = "hifi" }
>> +};
>> +
>> +static struct clk_regmap nna_core_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_NNA_CLK_CNTL,
>> +             .mask = 0x7,
>> +             .shift = 9,
>> +             .table = nna_parent_table,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "nna_core_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = nna_parent_data,
>> +             .num_parents = ARRAY_SIZE(nna_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap nna_core_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_NNA_CLK_CNTL,
>> +             .shift = 0,
>> +             .width = 7,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "nna_core_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &nna_core_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap nna_core = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_NNA_CLK_CNTL,
>> +             .bit_idx = 8,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "nna_core",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &nna_core_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap nna_axi_sel = {
>> +     .data = &(struct clk_regmap_mux_data) {
>> +             .offset = CLKCTRL_NNA_CLK_CNTL,
>> +             .mask = 0x7,
>> +             .shift = 25,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "nna_axi_sel",
>> +             .ops = &clk_regmap_mux_ops,
>> +             .parent_data = nna_parent_data,
>> +             .num_parents = ARRAY_SIZE(nna_parent_data),
>> +     },
>> +};
>> +
>> +static struct clk_regmap nna_axi_div = {
>> +     .data = &(struct clk_regmap_div_data) {
>> +             .offset = CLKCTRL_NNA_CLK_CNTL,
>> +             .shift = 16,
>> +             .width = 7,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "nna_axi_div",
>> +             .ops = &clk_regmap_divider_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &nna_axi_sel.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_regmap nna_axi = {
>> +     .data = &(struct clk_regmap_gate_data) {
>> +             .offset = CLKCTRL_NNA_CLK_CNTL,
>> +             .bit_idx = 24,
>> +     },
>> +     .hw.init = &(struct clk_init_data) {
>> +             .name = "nna_axi",
>> +             .ops = &clk_regmap_gate_ops,
>> +             .parent_hws = (const struct clk_hw *[]) {
>> +                     &nna_axi_div.hw
>> +             },
>> +             .num_parents = 1,
>> +             .flags = CLK_SET_RATE_PARENT,
>> +     },
>> +};
>> +
>> +static struct clk_hw *a5_periphs_hw_clks[] = {
>> +     [CLKID_RTC_XTAL_CLKIN]          = &rtc_xtal_clkin.hw,
>> +     [CLKID_RTC_32K_DIV]             = &rtc_32k_div.hw,
>> +     [CLKID_RTC_32K_MUX]             = &rtc_32k_mux.hw,
>> +     [CLKID_RTC_32K]                 = &rtc_32k.hw,
>> +     [CLKID_RTC_CLK]                 = &rtc_clk.hw,
>> +     [CLKID_SYS_RESET_CTRL]          = &sys_reset_ctrl.hw,
>> +     [CLKID_SYS_PWR_CTRL]            = &sys_pwr_ctrl.hw,
>> +     [CLKID_SYS_PAD_CTRL]            = &sys_pad_ctrl.hw,
>> +     [CLKID_SYS_CTRL]                = &sys_ctrl.hw,
>> +     [CLKID_SYS_TS_PLL]              = &sys_ts_pll.hw,
>> +     [CLKID_SYS_DEV_ARB]             = &sys_dev_arb.hw,
>> +     [CLKID_SYS_MMC_PCLK]            = &sys_mmc_pclk.hw,
>> +     [CLKID_SYS_MAILBOX]             = &sys_mailbox.hw,
>> +     [CLKID_SYS_CPU_CTRL]            = &sys_cpu_ctrl.hw,
>> +     [CLKID_SYS_JTAG_CTRL]           = &sys_jtag_ctrl.hw,
>> +     [CLKID_SYS_IR_CTRL]             = &sys_ir_ctrl.hw,
>> +     [CLKID_SYS_IRQ_CTRL]            = &sys_irq_ctrl.hw,
>> +     [CLKID_SYS_MSR_CLK]             = &sys_msr_clk.hw,
>> +     [CLKID_SYS_ROM]                 = &sys_rom.hw,
>> +     [CLKID_SYS_CPU_ARB]             = &sys_cpu_apb.hw,
>> +     [CLKID_SYS_RSA]                 = &sys_rsa.hw,
>> +     [CLKID_SYS_SAR_ADC]             = &sys_sar_adc.hw,
>> +     [CLKID_SYS_STARTUP]             = &sys_startup.hw,
>> +     [CLKID_SYS_SECURE]              = &sys_secure.hw,
>> +     [CLKID_SYS_SPIFC]               = &sys_spifc.hw,
>> +     [CLKID_SYS_DSPA]                = &sys_dspa.hw,
>> +     [CLKID_SYS_NNA]                 = &sys_nna.hw,
>> +     [CLKID_SYS_ETH_MAC]             = &sys_eth_mac.hw,
>> +     [CLKID_SYS_GIC]                 = &sys_gic.hw,
>> +     [CLKID_SYS_RAMA]                = &sys_rama.hw,
>> +     [CLKID_SYS_BIG_NIC]             = &sys_big_nic.hw,
>> +     [CLKID_SYS_RAMB]                = &sys_ramb.hw,
>> +     [CLKID_SYS_AUDIO_TOP]           = &sys_audio_top.hw,
>> +     [CLKID_SYS_AUDIO_VAD]           = &sys_audio_vad.hw,
>> +     [CLKID_SYS_USB]                 = &sys_usb.hw,
>> +     [CLKID_SYS_SD_EMMC_A]           = &sys_sd_emmc_a.hw,
>> +     [CLKID_SYS_SD_EMMC_C]           = &sys_sd_emmc_c.hw,
>> +     [CLKID_SYS_PWM_AB]              = &sys_pwm_ab.hw,
>> +     [CLKID_SYS_PWM_CD]              = &sys_pwm_cd.hw,
>> +     [CLKID_SYS_PWM_EF]              = &sys_pwm_ef.hw,
>> +     [CLKID_SYS_PWM_GH]              = &sys_pwm_gh.hw,
>> +     [CLKID_SYS_SPICC_1]             = &sys_spicc_1.hw,
>> +     [CLKID_SYS_SPICC_0]             = &sys_spicc_0.hw,
>> +     [CLKID_SYS_UART_A]              = &sys_uart_a.hw,
>> +     [CLKID_SYS_UART_B]              = &sys_uart_b.hw,
>> +     [CLKID_SYS_UART_C]              = &sys_uart_c.hw,
>> +     [CLKID_SYS_UART_D]              = &sys_uart_d.hw,
>> +     [CLKID_SYS_UART_E]              = &sys_uart_e.hw,
>> +     [CLKID_SYS_I2C_M_A]             = &sys_i2c_m_a.hw,
>> +     [CLKID_SYS_I2C_M_B]             = &sys_i2c_m_b.hw,
>> +     [CLKID_SYS_I2C_M_C]             = &sys_i2c_m_c.hw,
>> +     [CLKID_SYS_I2C_M_D]             = &sys_i2c_m_d.hw,
>> +     [CLKID_SYS_RTC]                 = &sys_rtc.hw,
>> +     [CLKID_AXI_AUDIO_VAD]           = &axi_audio_vad.hw,
>> +     [CLKID_AXI_AUDIO_TOP]           = &axi_audio_top.hw,
>> +     [CLKID_AXI_SYS_NIC]             = &axi_sys_nic.hw,
>> +     [CLKID_AXI_RAMB]                = &axi_ramb.hw,
>> +     [CLKID_AXI_RAMA]                = &axi_rama.hw,
>> +     [CLKID_AXI_CPU_DMC]             = &axi_cpu_dmc.hw,
>> +     [CLKID_AXI_NNA]                 = &axi_nna.hw,
>> +     [CLKID_AXI_DEV1_DMC]            = &axi_dev1_dmc.hw,
>> +     [CLKID_AXI_DEV0_DMC]            = &axi_dev0_dmc.hw,
>> +     [CLKID_AXI_DSP_DMC]             = &axi_dsp_dmc.hw,
>> +     [CLKID_12_24M_IN]               = &clk_12_24m_in.hw,
>> +     [CLKID_12M_24M]                 = &clk_12_24m.hw,
>> +     [CLKID_FCLK_25M_DIV]            = &fclk_25m_div.hw,
>> +     [CLKID_FCLK_25M]                = &fclk_25m.hw,
>> +     [CLKID_GEN_SEL]                 = &gen_sel.hw,
>> +     [CLKID_GEN_DIV]                 = &gen_div.hw,
>> +     [CLKID_GEN]                     = &gen.hw,
>> +     [CLKID_SARADC_SEL]              = &saradc_sel.hw,
>> +     [CLKID_SARADC_DIV]              = &saradc_div.hw,
>> +     [CLKID_SARADC]                  = &saradc.hw,
>> +     [CLKID_PWM_A_SEL]               = &pwm_a_sel.hw,
>> +     [CLKID_PWM_A_DIV]               = &pwm_a_div.hw,
>> +     [CLKID_PWM_A]                   = &pwm_a.hw,
>> +     [CLKID_PWM_B_SEL]               = &pwm_b_sel.hw,
>> +     [CLKID_PWM_B_DIV]               = &pwm_b_div.hw,
>> +     [CLKID_PWM_B]                   = &pwm_b.hw,
>> +     [CLKID_PWM_C_SEL]               = &pwm_c_sel.hw,
>> +     [CLKID_PWM_C_DIV]               = &pwm_c_div.hw,
>> +     [CLKID_PWM_C]                   = &pwm_c.hw,
>> +     [CLKID_PWM_D_SEL]               = &pwm_d_sel.hw,
>> +     [CLKID_PWM_D_DIV]               = &pwm_d_div.hw,
>> +     [CLKID_PWM_D]                   = &pwm_d.hw,
>> +     [CLKID_PWM_E_SEL]               = &pwm_e_sel.hw,
>> +     [CLKID_PWM_E_DIV]               = &pwm_e_div.hw,
>> +     [CLKID_PWM_E]                   = &pwm_e.hw,
>> +     [CLKID_PWM_F_SEL]               = &pwm_f_sel.hw,
>> +     [CLKID_PWM_F_DIV]               = &pwm_f_div.hw,
>> +     [CLKID_PWM_F]                   = &pwm_f.hw,
>> +     [CLKID_PWM_G_SEL]               = &pwm_g_sel.hw,
>> +     [CLKID_PWM_G_DIV]               = &pwm_g_div.hw,
>> +     [CLKID_PWM_G]                   = &pwm_g.hw,
>> +     [CLKID_PWM_H_SEL]               = &pwm_h_sel.hw,
>> +     [CLKID_PWM_H_DIV]               = &pwm_h_div.hw,
>> +     [CLKID_PWM_H]                   = &pwm_h.hw,
>> +     [CLKID_SPICC_0_SEL]             = &spicc_0_sel.hw,
>> +     [CLKID_SPICC_0_DIV]             = &spicc_0_div.hw,
>> +     [CLKID_SPICC_0]                 = &spicc_0.hw,
>> +     [CLKID_SPICC_1_SEL]             = &spicc_1_sel.hw,
>> +     [CLKID_SPICC_1_DIV]             = &spicc_1_div.hw,
>> +     [CLKID_SPICC_1]                 = &spicc_1.hw,
>> +     [CLKID_SD_EMMC_A_SEL]           = &sd_emmc_a_sel.hw,
>> +     [CLKID_SD_EMMC_A_DIV]           = &sd_emmc_a_div.hw,
>> +     [CLKID_SD_EMMC_A]               = &sd_emmc_a.hw,
>> +     [CLKID_SD_EMMC_C_SEL]           = &sd_emmc_c_sel.hw,
>> +     [CLKID_SD_EMMC_C_DIV]           = &sd_emmc_c_div.hw,
>> +     [CLKID_SD_EMMC_C]               = &sd_emmc_c.hw,
>> +     [CLKID_TS_DIV]                  = &ts_div.hw,
>> +     [CLKID_TS]                      = &ts.hw,
>> +     [CLKID_ETH_125M_DIV]            = &eth_125m_div.hw,
>> +     [CLKID_ETH_125M]                = &eth_125m.hw,
>> +     [CLKID_ETH_RMII_DIV]            = &eth_rmii_div.hw,
>> +     [CLKID_ETH_RMII]                = &eth_rmii.hw,
>> +     [CLKID_DSPA_0_SEL]              = &dspa_0_sel.hw,
>> +     [CLKID_DSPA_0_DIV]              = &dspa_0_div.hw,
>> +     [CLKID_DSPA_0]                  = &dspa_0.hw,
>> +     [CLKID_DSPA_1_SEL]              = &dspa_1_sel.hw,
>> +     [CLKID_DSPA_1_DIV]              = &dspa_1_div.hw,
>> +     [CLKID_DSPA_1]                  = &dspa_1.hw,
>> +     [CLKID_DSPA]                    = &dspa.hw,
>> +     [CLKID_NNA_CORE_SEL]            = &nna_core_sel.hw,
>> +     [CLKID_NNA_CORE_DIV]            = &nna_core_div.hw,
>> +     [CLKID_NNA_CORE]                = &nna_core.hw,
>> +     [CLKID_NNA_AXI_SEL]             = &nna_axi_sel.hw,
>> +     [CLKID_NNA_AXI_DIV]             = &nna_axi_div.hw,
>> +     [CLKID_NNA_AXI]                 = &nna_axi.hw,
>> +};
>> +
>> +/* Convenience table to populate regmap in .probe */
>> +static struct clk_regmap *const a5_periphs_clk_regmaps[] = {
>> +     &rtc_xtal_clkin,
>> +     &rtc_32k_div,
>> +     &rtc_32k_mux,
>> +     &rtc_32k,
>> +     &rtc_clk,
>> +     &sys_reset_ctrl,
>> +     &sys_pwr_ctrl,
>> +     &sys_pad_ctrl,
>> +     &sys_ctrl,
>> +     &sys_ts_pll,
>> +     &sys_dev_arb,
>> +     &sys_mmc_pclk,
>> +     &sys_mailbox,
>> +     &sys_cpu_ctrl,
>> +     &sys_jtag_ctrl,
>> +     &sys_ir_ctrl,
>> +     &sys_irq_ctrl,
>> +     &sys_msr_clk,
>> +     &sys_rom,
>> +     &sys_cpu_apb,
>> +     &sys_rsa,
>> +     &sys_sar_adc,
>> +     &sys_startup,
>> +     &sys_secure,
>> +     &sys_spifc,
>> +     &sys_dspa,
>> +     &sys_nna,
>> +     &sys_eth_mac,
>> +     &sys_gic,
>> +     &sys_rama,
>> +     &sys_big_nic,
>> +     &sys_ramb,
>> +     &sys_audio_top,
>> +     &sys_audio_vad,
>> +     &sys_usb,
>> +     &sys_sd_emmc_a,
>> +     &sys_sd_emmc_c,
>> +     &sys_pwm_ab,
>> +     &sys_pwm_cd,
>> +     &sys_pwm_ef,
>> +     &sys_pwm_gh,
>> +     &sys_spicc_1,
>> +     &sys_spicc_0,
>> +     &sys_uart_a,
>> +     &sys_uart_b,
>> +     &sys_uart_c,
>> +     &sys_uart_d,
>> +     &sys_uart_e,
>> +     &sys_i2c_m_a,
>> +     &sys_i2c_m_b,
>> +     &sys_i2c_m_c,
>> +     &sys_i2c_m_d,
>> +     &sys_rtc,
>> +     &axi_audio_vad,
>> +     &axi_audio_top,
>> +     &axi_sys_nic,
>> +     &axi_ramb,
>> +     &axi_rama,
>> +     &axi_cpu_dmc,
>> +     &axi_nna,
>> +     &axi_dev1_dmc,
>> +     &axi_dev0_dmc,
>> +     &axi_dsp_dmc,
>> +     &clk_12_24m_in,
>> +     &clk_12_24m,
>> +     &fclk_25m_div,
>> +     &fclk_25m,
>> +     &gen_sel,
>> +     &gen_div,
>> +     &gen,
>> +     &saradc_sel,
>> +     &saradc_div,
>> +     &saradc,
>> +     &pwm_a_sel,
>> +     &pwm_a_div,
>> +     &pwm_a,
>> +     &pwm_b_sel,
>> +     &pwm_b_div,
>> +     &pwm_b,
>> +     &pwm_c_sel,
>> +     &pwm_c_div,
>> +     &pwm_c,
>> +     &pwm_d_sel,
>> +     &pwm_d_div,
>> +     &pwm_d,
>> +     &pwm_e_sel,
>> +     &pwm_e_div,
>> +     &pwm_e,
>> +     &pwm_f_sel,
>> +     &pwm_f_div,
>> +     &pwm_f,
>> +     &pwm_g_sel,
>> +     &pwm_g_div,
>> +     &pwm_g,
>> +     &pwm_h_sel,
>> +     &pwm_h_div,
>> +     &pwm_h,
>> +     &spicc_0_sel,
>> +     &spicc_0_div,
>> +     &spicc_0,
>> +     &spicc_1_sel,
>> +     &spicc_1_div,
>> +     &spicc_1,
>> +     &sd_emmc_a_sel,
>> +     &sd_emmc_a_div,
>> +     &sd_emmc_a,
>> +     &sd_emmc_c_sel,
>> +     &sd_emmc_c_div,
>> +     &sd_emmc_c,
>> +     &ts_div,
>> +     &ts,
>> +     &eth_125m,
>> +     &eth_rmii_div,
>> +     &eth_rmii,
>> +     &dspa_0_sel,
>> +     &dspa_0_div,
>> +     &dspa_0,
>> +     &dspa_1_sel,
>> +     &dspa_1_div,
>> +     &dspa_1,
>> +     &dspa,
>> +     &nna_core_sel,
>> +     &nna_core_div,
>> +     &nna_core,
>> +     &nna_axi_sel,
>> +     &nna_axi_div,
>> +     &nna_axi
>> +};
>> +
>> +static const struct regmap_config clkc_regmap_config = {
>> +     .reg_bits       = 32,
>> +     .val_bits       = 32,
>> +     .reg_stride     = 4,
>> +     .max_register   = CLKCTRL_NNA_CLK_CNTL,
>> +};
>> +
>> +static struct meson_clk_hw_data a5_periphs_clks = {
>> +     .hws = a5_periphs_hw_clks,
>> +     .num = ARRAY_SIZE(a5_periphs_hw_clks),
>> +};
>> +
>> +static int aml_a5_peripherals_probe(struct platform_device *pdev)
>> +{
>> +     struct device *dev = &pdev->dev;
>> +     struct regmap *regmap;
>> +     void __iomem *base;
>> +     int clkid, ret, i;
>> +
>> +     base = devm_platform_ioremap_resource(pdev, 0);
>> +     if (IS_ERR(base))
>> +             return PTR_ERR(base);
>> +
>> +     regmap = devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
>> +     if (IS_ERR(regmap))
>> +             return PTR_ERR(regmap);
>> +
>> +     /* Populate regmap for the regmap backed clocks */
>> +     for (i = 0; i < ARRAY_SIZE(a5_periphs_clk_regmaps); i++)
>> +             a5_periphs_clk_regmaps[i]->map = regmap;
>> +
>> +     for (clkid = 0; clkid < a5_periphs_clks.num; clkid++) {
>> +             /* array might be sparse */
>> +             if (!a5_periphs_clks.hws[clkid])
>> +                     continue;
>> +
>> +             ret = devm_clk_hw_register(dev, a5_periphs_clks.hws[clkid]);
>> +             if (ret) {
>> +                     dev_err(dev, "Clock registration failed\n");
>> +                     return ret;
>> +             }
>> +     }
>> +
>> +     return devm_of_clk_add_hw_provider(dev, meson_clk_hw_get,
>> +                                        &a5_periphs_clks);
>> +}
>> +
>> +static const struct of_device_id a5_peripherals_clkc_match_table[] = {
>> +     {
>> +             .compatible = "amlogic,a5-peripherals-clkc",
>> +     },
>> +     { /* sentinel */ }
>> +};
>> +
>> +MODULE_DEVICE_TABLE(of, a5_peripherals_clkc_match_table);
>> +
>> +static struct platform_driver a5_peripherals_driver = {
>> +     .probe          = aml_a5_peripherals_probe,
>> +     .driver         = {
>> +             .name   = "a5-peripherals-clkc",
>> +             .of_match_table = a5_peripherals_clkc_match_table,
>> +     },
>> +};
>> +module_platform_driver(a5_peripherals_driver);
>> +
>> +MODULE_DESCRIPTION("Amlogic A5 Peripherals Clock Controller driver");
>> +MODULE_AUTHOR("Chuan Liu <[e-mail]>");
>> +MODULE_LICENSE("GPL");
> 
> --
> Jerome

Jerome Brunet Sept. 30, 2024, 10:16 a.m. UTC | #3

On Sun 29 Sep 2024 at 16:44, Xianwei Zhao <[e-mail]> wrote:

[...]

>>> +static A4_SYS_GATE(sys_eth_mac,              CLKCTRL_SYS_CLK_EN0_REG0, 26, 0);
>>> +
>>> +/*
>>> + * FIXME: sys_gic provides the clock for GIC(Generic Interrupt Controller).
>>> + * After clock is disabled, The GIC cannot work properly. At present, the driver
>>> + * used by our GIC is the public driver in kernel, and there is no management
>>> + * clock in the driver.
>>> + */
>>> +static A4_SYS_GATE(sys_gic,          CLKCTRL_SYS_CLK_EN0_REG0, 27, CLK_IS_CRITICAL);
>> The GIC has a driver. If it needs clock, maybe it should request it and
>> enable it, maybe as optional.
>> 
>
> This has been explained in C3. GIC is a public driver that does not
> reference clock, so you suggest setting it as CRITICAL and adding the
> "FIXME" annotation.

Yes indeed ... and at some point, it is expected something will be done
a actually fix the situation ... not just pile-up FIXME comments.

Adding a clock to a driver that should have one seems doable.

>
>>> +static A4_SYS_GATE(sys_rama,         CLKCTRL_SYS_CLK_EN0_REG0, 28, 0);
>>> +
>>> +/*
>>> + * NOTE: sys_big_nic provides the clock to the control bus of the NIC(Network
>>> + * Interface Controller) between multiple devices(CPU, DDR, RAM, ROM, GIC,
>>> + * SPIFC, CAPU, JTAG, EMMC, SDIO, sec_top, USB, Audio, ETH, SPICC) in the
>>> + * system. After clock is disabled, The NIC cannot work.
>>> + */
>> This comment looks like a clock that should be passed as ressource to a
>> bus or power-domain to be properly manage. This is a pattern that keeps
>> on repeating. I will not block you on it this time around but I strong
>> suggest you fix up the situation on the related platform. Next time
>> around, the reason won't be a valid one.
>> 
>
> There are too many modules associated with this clock... The most important
> is the inclusion of some system-level modules that are not managed by the
> driver in the kernel and cannot close their clocks, perhaps it is not
> appropriate to describe it here.
>
> In the next version I moved it to scmi-clk for management?

No. The number of module associated with a clock should not be a
concern and SCMI should not be a 'Hide all the things I don't want to do
in linux things'.

You've got a bus that needs a clocks. There are possibilities associate
a clock with bus in DT, either directly or through power-domains. Please
do it correctly.

>
>>> +static A4_SYS_GATE(sys_big_nic,              CLKCTRL_SYS_CLK_EN0_REG0, 29, CLK_IS_CRITICAL);
>>> +static A4_SYS_GATE(sys_ramb,         CLKCTRL_SYS_CLK_EN0_REG0, 30, 0);
>>> +static A4_SYS_GATE(sys_audio_top,    CLKCTRL_SYS_CLK_EN0_REG1, 0, 0);
>>> +static A4_SYS_GATE(sys_audio_vad,    CLKCTRL_SYS_CLK_EN0_REG1, 1, 0);
>>> +static A4_SYS_GATE(sys_usb,          CLKCTRL_SYS_CLK_EN0_REG1, 2, 0);
>>> +static A4_SYS_GATE(sys_sd_emmc_a,    CLKCTRL_SYS_CLK_EN0_REG1, 3, 0);
>>> +static A4_SYS_GATE(sys_sd_emmc_c,    CLKCTRL_SYS_CLK_EN0_REG1, 4, 0);
>>> +static A4_SYS_GATE(sys_pwm_ab,               CLKCTRL_SYS_CLK_EN0_REG1, 5, 0);
>>> +static A4_SYS_GATE(sys_pwm_cd,               CLKCTRL_SYS_CLK_EN0_REG1, 6, 0);
>>> +static A4_SYS_GATE(sys_pwm_ef,               CLKCTRL_SYS_CLK_EN0_REG1, 7, 0);
>>> +static A4_SYS_GATE(sys_pwm_gh,               CLKCTRL_SYS_CLK_EN0_REG1, 8, 0);
>>> +static A4_SYS_GATE(sys_spicc_1,              CLKCTRL_SYS_CLK_EN0_REG1, 9, 0);
>>> +static A4_SYS_GATE(sys_spicc_0,              CLKCTRL_SYS_CLK_EN0_REG1, 10, 0);
>>> +static A4_SYS_GATE(sys_uart_a,               CLKCTRL_SYS_CLK_EN0_REG1, 11, 0);
>>> +static A4_SYS_GATE(sys_uart_b,               CLKCTRL_SYS_CLK_EN0_REG1, 12, 0);
>>> +static A4_SYS_GATE(sys_uart_c,               CLKCTRL_SYS_CLK_EN0_REG1, 13, 0);
>>> +static A4_SYS_GATE(sys_uart_d,               CLKCTRL_SYS_CLK_EN0_REG1, 14, 0);
>>> +static A4_SYS_GATE(sys_uart_e,               CLKCTRL_SYS_CLK_EN0_REG1, 15, 0);
>>> +static A4_SYS_GATE(sys_i2c_m_a,              CLKCTRL_SYS_CLK_EN0_REG1, 16, 0);
>>> +static A4_SYS_GATE(sys_i2c_m_b,              CLKCTRL_SYS_CLK_EN0_REG1, 17, 0);
>>> +static A4_SYS_GATE(sys_i2c_m_c,              CLKCTRL_SYS_CLK_EN0_REG1, 18, 0);
>>> +static A4_SYS_GATE(sys_i2c_m_d,              CLKCTRL_SYS_CLK_EN0_REG1, 19, 0);
>>> +static A4_SYS_GATE(sys_rtc,          CLKCTRL_SYS_CLK_EN0_REG1, 21, 0);
>>> +
>>> +#define A4_AXI_GATE(_name, _reg, _bit, _flags)                               \
>>> +     A4_CLK_GATE(_name, _reg, _bit, axiclk,                          \
>>> +                 &clk_regmap_gate_ops, _flags)
>>> +
>>> +static A4_AXI_GATE(axi_audio_vad,    CLKCTRL_AXI_CLK_EN0, 0, 0);
>>> +static A4_AXI_GATE(axi_audio_top,    CLKCTRL_AXI_CLK_EN0, 1, 0);
>>> +
>>> +/*
>>> + * NOTE: axi_sys_nic provides the clock to the AXI bus of the system NIC. After
>>> + * clock is disabled, The NIC cannot work.
>>> + */
>>> +static A4_AXI_GATE(axi_sys_nic,              CLKCTRL_AXI_CLK_EN0, 2, CLK_IS_CRITICAL);
>>> +static A4_AXI_GATE(axi_ramb,         CLKCTRL_AXI_CLK_EN0, 5, 0);
>>> +static A4_AXI_GATE(axi_rama,         CLKCTRL_AXI_CLK_EN0, 6, 0);
>>> +
>>> +/*
>>> + * NOTE: axi_cpu_dmc provides the clock to the AXI bus where the CPU accesses
>>> + * the DDR. After clock is disabled, The CPU will not have access to the DDR.
>>> + */
>>> +static A4_AXI_GATE(axi_cpu_dmc,              CLKCTRL_AXI_CLK_EN0, 7, CLK_IS_CRITICAL);
>>> +static A4_AXI_GATE(axi_nna,          CLKCTRL_AXI_CLK_EN0, 12, 0);
>>> +
>>> +/*
>>> + * NOTE: axi_dev1_dmc provides the clock for the peripherals(EMMC, SDIO,
>>> + * sec_top, USB, Audio) to access the AXI bus of the DDR.
>>> + */
>> Same.
>> 
>
> These normal peripheral drivers manage the clock without a problem.
>
>>> +static A4_AXI_GATE(axi_dev1_dmc,     CLKCTRL_AXI_CLK_EN0, 13, 0);
>>> +
>>> +/*
>>> + * NOTE: axi_dev0_dmc provides the clock for the peripherals(ETH and SPICC)
>>> + * to access the AXI bus of the DDR.
>>> + */
>>> +static A4_AXI_GATE(axi_dev0_dmc,     CLKCTRL_AXI_CLK_EN0, 14, 0);
>>> +static A4_AXI_GATE(axi_dsp_dmc,              CLKCTRL_AXI_CLK_EN0, 15, 0);
>>> +
>>> +static struct clk_regmap clk_12_24m_in = {
>>> +     .data = &(struct clk_regmap_gate_data) {
>>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>>> +             .bit_idx = 11,
>>> +     },
>>> +     .hw.init = &(struct clk_init_data) {
>>> +             .name = "clk_12_24m_in",
>>> +             .ops = &clk_regmap_gate_ops,
>>> +             .parent_data = &(const struct clk_parent_data) {
>>> +                     .fw_name = "xtal_24m",
>>> +             },
>>> +             .num_parents = 1,
>>> +     },
>>> +};
>>> +
>>> +static struct clk_regmap clk_12_24m = {
>>> +     .data = &(struct clk_regmap_div_data) {
>>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>>> +             .shift = 10,
>>> +             .width = 1,
>>> +     },
>>> +     .hw.init = &(struct clk_init_data) {
>>> +             .name = "clk_12_24m",
>>> +             .ops = &clk_regmap_divider_ops,
>>> +             .parent_hws = (const struct clk_hw *[]) {
>>> +                     &clk_12_24m_in.hw
>>> +             },
>>> +             .num_parents = 1,
>>> +     },
>>> +};
>>> +
>>> +/* FIXME: set value 0 will div by 2 like value 1 */
>> Again, it is fine when it happens once, like the c3.
>> When the pattern starts repeating, it is time to do something about it.
>> 
>
> The corresponding suggestions have been made to the hardware designer, but
> now the designed chip cannot be repaired.

Not asking to fix the HW (although that would be nice if you could)
The HW is what it is. The SW needs fixing. That you can do.

>
>>> +static struct clk_regmap fclk_25m_div = {
>>> +     .data = &(struct clk_regmap_div_data) {
>>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>>> +             .shift = 0,
>>> +             .width = 8,
>>> +     },
>>> +     .hw.init = &(struct clk_init_data) {
>>> +             .name = "fclk_25m_div",
>>> +             .ops = &clk_regmap_divider_ops,
>>> +             .parent_data = &(const struct clk_parent_data) {
>>> +                     .fw_name = "fix",
>>> +             },
>>> +             .num_parents = 1,
>>> +     },
>>> +};
>>> +
>>> +static struct clk_regmap fclk_25m = {
>>> +     .data = &(struct clk_regmap_gate_data) {
>>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>>> +             .bit_idx = 12,
>>> +     },
>>> +     .hw.init = &(struct clk_init_data) {
>>> +             .name = "fclk_25m",
>>> +             .ops = &clk_regmap_gate_ops,
>>> +             .parent_hws = (const struct clk_hw *[]) {
>>> +                     &fclk_25m_div.hw
>>> +             },
>>> +             .num_parents = 1,
>>> +             .flags = CLK_SET_RATE_PARENT,
>>> +     },
>>> +};
>>> +
>>> +/*
>>> + * Channel 3(ddr_dpll_pt_clk) is manged by the DDR module; channel 12(cts_msr_clk)
>>> + * is manged by clock measures module. Their hardware are out of clock tree.
>> Yet, they exist and should be part of the bindings since they are
>> obviously input to this clock.
>> 
>
> Will add it to bindings, as optional input clock source.
>
>>> + * Channel 4 5 8 9 10 11 13 14 15 16 18 are not connected.
>>> + *
>>> + * gp1 is designed for DSU (DynamIQ Shared Unit) alone. It cannot be changed
>>> + * arbitrarily. gp1 is read-only in the kernel and is only open for debug purposes.
>>> + */
>>> +static u32 gen_parent_table[] = { 0, 1, 2, 6, 7, 17, 19, 20, 21, 22, 23, 24, 25,
>>> +                               26, 27, 28};
>>> +
>>> +static const struct clk_parent_data gen_parent_data[] = {
>>> +     { .fw_name = "oscin" },
>>> +     { .hw = &rtc_clk.hw },
>>> +     { .fw_name = "sysplldiv16" },
>>> +     { .fw_name = "gp1" },
>>> +     { .fw_name = "hifi" },
>>> +     { .fw_name = "cpudiv16" },
>>> +     { .fw_name = "fdiv2" },
>>> +     { .fw_name = "fdiv2p5" },
>>> +     { .fw_name = "fdiv3" },
>>> +     { .fw_name = "fdiv4" },
>>> +     { .fw_name = "fdiv5" },
>>> +     { .fw_name = "fdiv7" },
>>> +     { .fw_name = "mpll0" },
>>> +     { .fw_name = "mpll1" },
>>> +     { .fw_name = "mpll2" },
>>> +     { .fw_name = "mpll3" }
>>> +};

[...]

>>> +
>>> +static struct clk_regmap pwm_h_sel =
>>> +     AML_PWM_CLK_MUX(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 25);
>>> +static struct clk_regmap pwm_h_div =
>>> +     AML_PWM_CLK_DIV(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 16);
>>> +static struct clk_regmap pwm_h =
>>> +     AML_PWM_CLK_GATE(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 24);
>>> +
>>> +/* Channel 7 is gp1. */
>> and ? if GP1 is RO, why can't you add it here ?
>> 
>
> gp1_pll is a special clock for DSU, it is integrated into dsu_clk, we
> don't want other modules to reference it.
>
> My understanding is that gp1_pll should not be provided to the peripheral
> clock tree, perhaps this is a redundant design.

Then /* Channel 7 is gp1 which is reserved for DSU */

Note that if GP1 is actually RO and DSU does not change the rate at
runtime through other means, then listing GP1 here should not be a
problem, spi would just be user of an available PLL.

>
>>> +static const struct clk_parent_data spicc_parent_data[] = {
>>> +     { .fw_name = "oscin" },
>>> +     { .fw_name = "sysclk" },
>>> +     { .fw_name = "fdiv4" },
>>> +     { .fw_name = "fdiv3" },
>>> +     { .fw_name = "fdiv2" },
>>> +     { .fw_name = "fdiv5" },
>>> +     { .fw_name = "fdiv7" }
>>> +};
>>> +
>>> +static struct clk_regmap spicc_0_sel = {
>>> +     .data = &(struct clk_regmap_mux_data) {
>>> +             .offset = CLKCTRL_SPICC_CLK_CTRL,
>>> +             .mask = 0x7,
>>> +             .shift = 7,
>>> +     },
>>> +     .hw.init = &(struct clk_init_data) {
>>> +             .name = "spicc_0_sel",
>>> +             .ops = &clk_regmap_mux_ops,
>>> +             .parent_data = spicc_parent_data,
>>> +             .num_parents = ARRAY_SIZE(spicc_parent_data),
>>> +     },
>>> +};

[...]

>>> +
>>> +static struct clk_regmap dspa_1 = {
>>> +     .data = &(struct clk_regmap_gate_data) {
>>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>>> +             .bit_idx = 29,
>>> +     },
>>> +     .hw.init = &(struct clk_init_data) {
>>> +             .name = "dspa_1",
>>> +             .ops = &clk_regmap_gate_ops,
>>> +             .parent_hws = (const struct clk_hw *[]) {
>>> +                     &dspa_1_div.hw
>>> +             },
>>> +             .num_parents = 1,
>>> +             .flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,
>> A word about SET_RATE_GATE ?
>> 
>
> Look at the response to one of the questions below.

Still a word ? your comment below does justify this flag clearly.

>
>>> +     },
>>> +};
>>> +
>>> +static struct clk_regmap dspa = {
>>> +     .data = &(struct clk_regmap_mux_data){
>>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>>> +             .mask = 0x1,
>>> +             .shift = 15,
>>> +     },
>>> +     .hw.init = &(struct clk_init_data) {
>>> +             .name = "dspa",
>>> +             .ops = &clk_regmap_mux_ops,
>>> +             .parent_hws = (const struct clk_hw *[]) {
>>> +                     &dspa_0.hw,
>>> +                     &dspa_1.hw
>>> +             },
>>> +             .num_parents = 2,
>>> +             /*
>>> +              * NOTE: This level of mux is "no glitch mux", and mux_0
>>> +              * (here dspa_0) is not only the clock source for mux, but also
>>> +              * provides a working clock for "no glitch mux". "no glitch mux"
>>> +              * can be switched only when mux_0 has a clock input. Therefore,
>>> +              * add flag CLK_OPS_PARENT_ENABLE to ensure that mux_0 has clock
>>> +              * when "no glitch mux" works.
>>> +              */
>>> +             .flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
>> Humm CLK_OPS_PARENT_ENABLE is not how we have handling glitch free mux
>> so far. What changed ?
>> 
>
> This is a hidden problem we have discovered in recent years, the previous
> chip use is ping-pong switching "no-glitch-mux/glitch free" have this
> problem. If mux_0 does not have a clock "no-glitch-mux", it will not be
> able to switch channels, and I will organize and submit patch to fix it
> later.

The NOTE comment and what the code does are not aligned.
* Your comment says that input #0 must be enabled for the mux to work
* The flag ensure that parent is enabled before switching to it. There
  is nothing specific about input #0

>
>>> +     },
>>> +};
>>> +
>>> +/* Channel 6 is gp1. */
>>> +static u32 nna_parent_table[] = { 0, 1, 2, 3, 4, 5, 7};
>>> +
>>> +static const struct clk_parent_data nna_parent_data[] = {
>>> +     { .fw_name = "oscin" },
>>> +     { .fw_name = "fdiv2p5" },
>>> +     { .fw_name = "fdiv4" },
>>> +     { .fw_name = "fdiv3" },
>>> +     { .fw_name = "fdiv5" },
>>> +     { .fw_name = "fdiv2" },
>>> +     { .fw_name = "hifi" }
>>> +};

Xianwei Zhao Oct. 12, 2024, 5:50 a.m. UTC | #4

Hi Jerome,
     Thanks for your reply.

On 2024/9/30 18:16, Jerome Brunet wrote:
> [ EXTERNAL EMAIL ]
> 
> On Sun 29 Sep 2024 at 16:44, Xianwei Zhao <[e-mail]> wrote:
> 
> [...]
> 
>>>> +static A4_SYS_GATE(sys_eth_mac,              CLKCTRL_SYS_CLK_EN0_REG0, 26, 0);
>>>> +
>>>> +/*
>>>> + * FIXME: sys_gic provides the clock for GIC(Generic Interrupt Controller).
>>>> + * After clock is disabled, The GIC cannot work properly. At present, the driver
>>>> + * used by our GIC is the public driver in kernel, and there is no management
>>>> + * clock in the driver.
>>>> + */
>>>> +static A4_SYS_GATE(sys_gic,          CLKCTRL_SYS_CLK_EN0_REG0, 27, CLK_IS_CRITICAL);
>>> The GIC has a driver. If it needs clock, maybe it should request it and
>>> enable it, maybe as optional.
>>>
>>
>> This has been explained in C3. GIC is a public driver that does not
>> reference clock, so you suggest setting it as CRITICAL and adding the
>> "FIXME" annotation.
> 
> Yes indeed ... and at some point, it is expected something will be done
> a actually fix the situation ... not just pile-up FIXME comments.
> 
> Adding a clock to a driver that should have one seems doable.
> 
>>
>>>> +static A4_SYS_GATE(sys_rama,         CLKCTRL_SYS_CLK_EN0_REG0, 28, 0);
>>>> +
>>>> +/*
>>>> + * NOTE: sys_big_nic provides the clock to the control bus of the NIC(Network
>>>> + * Interface Controller) between multiple devices(CPU, DDR, RAM, ROM, GIC,
>>>> + * SPIFC, CAPU, JTAG, EMMC, SDIO, sec_top, USB, Audio, ETH, SPICC) in the
>>>> + * system. After clock is disabled, The NIC cannot work.
>>>> + */
>>> This comment looks like a clock that should be passed as ressource to a
>>> bus or power-domain to be properly manage. This is a pattern that keeps
>>> on repeating. I will not block you on it this time around but I strong
>>> suggest you fix up the situation on the related platform. Next time
>>> around, the reason won't be a valid one.
>>>
>>
>> There are too many modules associated with this clock... The most important
>> is the inclusion of some system-level modules that are not managed by the
>> driver in the kernel and cannot close their clocks, perhaps it is not
>> appropriate to describe it here.
>>
>> In the next version I moved it to scmi-clk for management?
> 
> No. The number of module associated with a clock should not be a
> concern and SCMI should not be a 'Hide all the things I don't want to do
> in linux things'.
> 
> You've got a bus that needs a clocks. There are possibilities associate
> a clock with bus in DT, either directly or through power-domains. Please
> do it correctly.
> 

I also wanted to process these key clocks in scmi-clk for the following 
reasons:

1 These clocks seriously affect system security and stability, and are 
managed in the security environment (BL31). Under bl31 we will add 
additional judgment logic to these clocks: If the kernel is in the 
runtime stage, critical sys_clk/axi_clk such as GIC/NIC/CPU_DMC are not 
allowed to disable (these clocks can be closed during deep sleep, 
because the aocpu is always alive to receive and process interrupts 
normally), this can also prevent attacks.

2 Register permissions corresponding to sys_clk/axi_clk can be 
configured in the TEE environment. After configuration, the clock cannot 
be disabled by writing registers in the REE environment.

3 This driver is used to manage clocks related to general peripherals. 
Clocks that affect system security are handled in the security 
environment through scmi-clk.

>>
>>>> +static A4_SYS_GATE(sys_big_nic,              CLKCTRL_SYS_CLK_EN0_REG0, 29, CLK_IS_CRITICAL);
>>>> +static A4_SYS_GATE(sys_ramb,         CLKCTRL_SYS_CLK_EN0_REG0, 30, 0);
>>>> +static A4_SYS_GATE(sys_audio_top,    CLKCTRL_SYS_CLK_EN0_REG1, 0, 0);
>>>> +static A4_SYS_GATE(sys_audio_vad,    CLKCTRL_SYS_CLK_EN0_REG1, 1, 0);
>>>> +static A4_SYS_GATE(sys_usb,          CLKCTRL_SYS_CLK_EN0_REG1, 2, 0);
>>>> +static A4_SYS_GATE(sys_sd_emmc_a,    CLKCTRL_SYS_CLK_EN0_REG1, 3, 0);
>>>> +static A4_SYS_GATE(sys_sd_emmc_c,    CLKCTRL_SYS_CLK_EN0_REG1, 4, 0);
>>>> +static A4_SYS_GATE(sys_pwm_ab,               CLKCTRL_SYS_CLK_EN0_REG1, 5, 0);
>>>> +static A4_SYS_GATE(sys_pwm_cd,               CLKCTRL_SYS_CLK_EN0_REG1, 6, 0);
>>>> +static A4_SYS_GATE(sys_pwm_ef,               CLKCTRL_SYS_CLK_EN0_REG1, 7, 0);
>>>> +static A4_SYS_GATE(sys_pwm_gh,               CLKCTRL_SYS_CLK_EN0_REG1, 8, 0);
>>>> +static A4_SYS_GATE(sys_spicc_1,              CLKCTRL_SYS_CLK_EN0_REG1, 9, 0);
>>>> +static A4_SYS_GATE(sys_spicc_0,              CLKCTRL_SYS_CLK_EN0_REG1, 10, 0);
>>>> +static A4_SYS_GATE(sys_uart_a,               CLKCTRL_SYS_CLK_EN0_REG1, 11, 0);
>>>> +static A4_SYS_GATE(sys_uart_b,               CLKCTRL_SYS_CLK_EN0_REG1, 12, 0);
>>>> +static A4_SYS_GATE(sys_uart_c,               CLKCTRL_SYS_CLK_EN0_REG1, 13, 0);
>>>> +static A4_SYS_GATE(sys_uart_d,               CLKCTRL_SYS_CLK_EN0_REG1, 14, 0);
>>>> +static A4_SYS_GATE(sys_uart_e,               CLKCTRL_SYS_CLK_EN0_REG1, 15, 0);
>>>> +static A4_SYS_GATE(sys_i2c_m_a,              CLKCTRL_SYS_CLK_EN0_REG1, 16, 0);
>>>> +static A4_SYS_GATE(sys_i2c_m_b,              CLKCTRL_SYS_CLK_EN0_REG1, 17, 0);
>>>> +static A4_SYS_GATE(sys_i2c_m_c,              CLKCTRL_SYS_CLK_EN0_REG1, 18, 0);
>>>> +static A4_SYS_GATE(sys_i2c_m_d,              CLKCTRL_SYS_CLK_EN0_REG1, 19, 0);
>>>> +static A4_SYS_GATE(sys_rtc,          CLKCTRL_SYS_CLK_EN0_REG1, 21, 0);
>>>> +
>>>> +#define A4_AXI_GATE(_name, _reg, _bit, _flags)                               \
>>>> +     A4_CLK_GATE(_name, _reg, _bit, axiclk,                          \
>>>> +                 &clk_regmap_gate_ops, _flags)
>>>> +
>>>> +static A4_AXI_GATE(axi_audio_vad,    CLKCTRL_AXI_CLK_EN0, 0, 0);
>>>> +static A4_AXI_GATE(axi_audio_top,    CLKCTRL_AXI_CLK_EN0, 1, 0);
>>>> +
>>>> +/*
>>>> + * NOTE: axi_sys_nic provides the clock to the AXI bus of the system NIC. After
>>>> + * clock is disabled, The NIC cannot work.
>>>> + */
>>>> +static A4_AXI_GATE(axi_sys_nic,              CLKCTRL_AXI_CLK_EN0, 2, CLK_IS_CRITICAL);
>>>> +static A4_AXI_GATE(axi_ramb,         CLKCTRL_AXI_CLK_EN0, 5, 0);
>>>> +static A4_AXI_GATE(axi_rama,         CLKCTRL_AXI_CLK_EN0, 6, 0);
>>>> +
>>>> +/*
>>>> + * NOTE: axi_cpu_dmc provides the clock to the AXI bus where the CPU accesses
>>>> + * the DDR. After clock is disabled, The CPU will not have access to the DDR.
>>>> + */
>>>> +static A4_AXI_GATE(axi_cpu_dmc,              CLKCTRL_AXI_CLK_EN0, 7, CLK_IS_CRITICAL);
>>>> +static A4_AXI_GATE(axi_nna,          CLKCTRL_AXI_CLK_EN0, 12, 0);
>>>> +
>>>> +/*
>>>> + * NOTE: axi_dev1_dmc provides the clock for the peripherals(EMMC, SDIO,
>>>> + * sec_top, USB, Audio) to access the AXI bus of the DDR.
>>>> + */
>>> Same.
>>>
>>
>> These normal peripheral drivers manage the clock without a problem.
>>
>>>> +static A4_AXI_GATE(axi_dev1_dmc,     CLKCTRL_AXI_CLK_EN0, 13, 0);
>>>> +
>>>> +/*
>>>> + * NOTE: axi_dev0_dmc provides the clock for the peripherals(ETH and SPICC)
>>>> + * to access the AXI bus of the DDR.
>>>> + */
>>>> +static A4_AXI_GATE(axi_dev0_dmc,     CLKCTRL_AXI_CLK_EN0, 14, 0);
>>>> +static A4_AXI_GATE(axi_dsp_dmc,              CLKCTRL_AXI_CLK_EN0, 15, 0);
>>>> +
>>>> +static struct clk_regmap clk_12_24m_in = {
>>>> +     .data = &(struct clk_regmap_gate_data) {
>>>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>>>> +             .bit_idx = 11,
>>>> +     },
>>>> +     .hw.init = &(struct clk_init_data) {
>>>> +             .name = "clk_12_24m_in",
>>>> +             .ops = &clk_regmap_gate_ops,
>>>> +             .parent_data = &(const struct clk_parent_data) {
>>>> +                     .fw_name = "xtal_24m",
>>>> +             },
>>>> +             .num_parents = 1,
>>>> +     },
>>>> +};
>>>> +
>>>> +static struct clk_regmap clk_12_24m = {
>>>> +     .data = &(struct clk_regmap_div_data) {
>>>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>>>> +             .shift = 10,
>>>> +             .width = 1,
>>>> +     },
>>>> +     .hw.init = &(struct clk_init_data) {
>>>> +             .name = "clk_12_24m",
>>>> +             .ops = &clk_regmap_divider_ops,
>>>> +             .parent_hws = (const struct clk_hw *[]) {
>>>> +                     &clk_12_24m_in.hw
>>>> +             },
>>>> +             .num_parents = 1,
>>>> +     },
>>>> +};
>>>> +
>>>> +/* FIXME: set value 0 will div by 2 like value 1 */
>>> Again, it is fine when it happens once, like the c3.
>>> When the pattern starts repeating, it is time to do something about it.
>>>
>>
>> The corresponding suggestions have been made to the hardware designer, but
>> now the designed chip cannot be repaired.
> 
> Not asking to fix the HW (although that would be nice if you could)
> The HW is what it is. The SW needs fixing. That you can do.
> 
>>
>>>> +static struct clk_regmap fclk_25m_div = {
>>>> +     .data = &(struct clk_regmap_div_data) {
>>>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>>>> +             .shift = 0,
>>>> +             .width = 8,
>>>> +     },
>>>> +     .hw.init = &(struct clk_init_data) {
>>>> +             .name = "fclk_25m_div",
>>>> +             .ops = &clk_regmap_divider_ops,
>>>> +             .parent_data = &(const struct clk_parent_data) {
>>>> +                     .fw_name = "fix",
>>>> +             },
>>>> +             .num_parents = 1,
>>>> +     },
>>>> +};
>>>> +
>>>> +static struct clk_regmap fclk_25m = {
>>>> +     .data = &(struct clk_regmap_gate_data) {
>>>> +             .offset = CLKCTRL_CLK12_24_CTRL,
>>>> +             .bit_idx = 12,
>>>> +     },
>>>> +     .hw.init = &(struct clk_init_data) {
>>>> +             .name = "fclk_25m",
>>>> +             .ops = &clk_regmap_gate_ops,
>>>> +             .parent_hws = (const struct clk_hw *[]) {
>>>> +                     &fclk_25m_div.hw
>>>> +             },
>>>> +             .num_parents = 1,
>>>> +             .flags = CLK_SET_RATE_PARENT,
>>>> +     },
>>>> +};
>>>> +
>>>> +/*
>>>> + * Channel 3(ddr_dpll_pt_clk) is manged by the DDR module; channel 12(cts_msr_clk)
>>>> + * is manged by clock measures module. Their hardware are out of clock tree.
>>> Yet, they exist and should be part of the bindings since they are
>>> obviously input to this clock.
>>>
>>
>> Will add it to bindings, as optional input clock source.
>>
>>>> + * Channel 4 5 8 9 10 11 13 14 15 16 18 are not connected.
>>>> + *
>>>> + * gp1 is designed for DSU (DynamIQ Shared Unit) alone. It cannot be changed
>>>> + * arbitrarily. gp1 is read-only in the kernel and is only open for debug purposes.
>>>> + */
>>>> +static u32 gen_parent_table[] = { 0, 1, 2, 6, 7, 17, 19, 20, 21, 22, 23, 24, 25,
>>>> +                               26, 27, 28};
>>>> +
>>>> +static const struct clk_parent_data gen_parent_data[] = {
>>>> +     { .fw_name = "oscin" },
>>>> +     { .hw = &rtc_clk.hw },
>>>> +     { .fw_name = "sysplldiv16" },
>>>> +     { .fw_name = "gp1" },
>>>> +     { .fw_name = "hifi" },
>>>> +     { .fw_name = "cpudiv16" },
>>>> +     { .fw_name = "fdiv2" },
>>>> +     { .fw_name = "fdiv2p5" },
>>>> +     { .fw_name = "fdiv3" },
>>>> +     { .fw_name = "fdiv4" },
>>>> +     { .fw_name = "fdiv5" },
>>>> +     { .fw_name = "fdiv7" },
>>>> +     { .fw_name = "mpll0" },
>>>> +     { .fw_name = "mpll1" },
>>>> +     { .fw_name = "mpll2" },
>>>> +     { .fw_name = "mpll3" }
>>>> +};
> 
> [...]
> 
>>>> +
>>>> +static struct clk_regmap pwm_h_sel =
>>>> +     AML_PWM_CLK_MUX(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 25);
>>>> +static struct clk_regmap pwm_h_div =
>>>> +     AML_PWM_CLK_DIV(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 16);
>>>> +static struct clk_regmap pwm_h =
>>>> +     AML_PWM_CLK_GATE(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 24);
>>>> +
>>>> +/* Channel 7 is gp1. */
>>> and ? if GP1 is RO, why can't you add it here ?
>>>
>>
>> gp1_pll is a special clock for DSU, it is integrated into dsu_clk, we
>> don't want other modules to reference it.
>>
>> My understanding is that gp1_pll should not be provided to the peripheral
>> clock tree, perhaps this is a redundant design.
> 
> Then /* Channel 7 is gp1 which is reserved for DSU */
> 
> Note that if GP1 is actually RO and DSU does not change the rate at
> runtime through other means, then listing GP1 here should not be a
> problem, spi would just be user of an available PLL.
> 

cpufreq(DVFS) driver will still dynamically adjust the frequency of gp1 
after running, but I configured gp1 as RO under bl31, and it is risky to 
open it to other peripheral modules.

For example, when the frequency of spicc is set, the frequency of gp1 is 
just enough to meet the requirements of spicc. At this time, spicc will 
switch to gp1. Later, when the cpufreq driver dynamically sets the 
frequency of gp1, it will be a disaster for spicc.... This may also 
happen in the future with peripherals that support hifi_pll (audio 
adaptation sampling rate and synchronization with video may dynamically 
adjust the hifipll frequency).

>>
>>>> +static const struct clk_parent_data spicc_parent_data[] = {
>>>> +     { .fw_name = "oscin" },
>>>> +     { .fw_name = "sysclk" },
>>>> +     { .fw_name = "fdiv4" },
>>>> +     { .fw_name = "fdiv3" },
>>>> +     { .fw_name = "fdiv2" },
>>>> +     { .fw_name = "fdiv5" },
>>>> +     { .fw_name = "fdiv7" }
>>>> +};
>>>> +
>>>> +static struct clk_regmap spicc_0_sel = {
>>>> +     .data = &(struct clk_regmap_mux_data) {
>>>> +             .offset = CLKCTRL_SPICC_CLK_CTRL,
>>>> +             .mask = 0x7,
>>>> +             .shift = 7,
>>>> +     },
>>>> +     .hw.init = &(struct clk_init_data) {
>>>> +             .name = "spicc_0_sel",
>>>> +             .ops = &clk_regmap_mux_ops,
>>>> +             .parent_data = spicc_parent_data,
>>>> +             .num_parents = ARRAY_SIZE(spicc_parent_data),
>>>> +     },
>>>> +};
> 
> [...]
> 
>>>> +
>>>> +static struct clk_regmap dspa_1 = {
>>>> +     .data = &(struct clk_regmap_gate_data) {
>>>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>>>> +             .bit_idx = 29,
>>>> +     },
>>>> +     .hw.init = &(struct clk_init_data) {
>>>> +             .name = "dspa_1",
>>>> +             .ops = &clk_regmap_gate_ops,
>>>> +             .parent_hws = (const struct clk_hw *[]) {
>>>> +                     &dspa_1_div.hw
>>>> +             },
>>>> +             .num_parents = 1,
>>>> +             .flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,
>>> A word about SET_RATE_GATE ?
>>>
>>
>> Look at the response to one of the questions below.
> 
> Still a word ? your comment below does justify this flag clearly.
> 

CLK_SET_RATE_GATE is to enable glitch free mux to perform ping-pong 
switching.

>>
>>>> +     },
>>>> +};
>>>> +
>>>> +static struct clk_regmap dspa = {
>>>> +     .data = &(struct clk_regmap_mux_data){
>>>> +             .offset = CLKCTRL_DSPA_CLK_CTRL0,
>>>> +             .mask = 0x1,
>>>> +             .shift = 15,
>>>> +     },
>>>> +     .hw.init = &(struct clk_init_data) {
>>>> +             .name = "dspa",
>>>> +             .ops = &clk_regmap_mux_ops,
>>>> +             .parent_hws = (const struct clk_hw *[]) {
>>>> +                     &dspa_0.hw,
>>>> +                     &dspa_1.hw
>>>> +             },
>>>> +             .num_parents = 2,
>>>> +             /*
>>>> +              * NOTE: This level of mux is "no glitch mux", and mux_0
>>>> +              * (here dspa_0) is not only the clock source for mux, but also
>>>> +              * provides a working clock for "no glitch mux". "no glitch mux"
>>>> +              * can be switched only when mux_0 has a clock input. Therefore,
>>>> +              * add flag CLK_OPS_PARENT_ENABLE to ensure that mux_0 has clock
>>>> +              * when "no glitch mux" works.
>>>> +              */
>>>> +             .flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
>>> Humm CLK_OPS_PARENT_ENABLE is not how we have handling glitch free mux
>>> so far. What changed ?
>>>
>>
>> This is a hidden problem we have discovered in recent years, the previous
>> chip use is ping-pong switching "no-glitch-mux/glitch free" have this
>> problem. If mux_0 does not have a clock "no-glitch-mux", it will not be
>> able to switch channels, and I will organize and submit patch to fix it
>> later.
> 
> The NOTE comment and what the code does are not aligned.
> * Your comment says that input #0 must be enabled for the mux to work
> * The flag ensure that parent is enabled before switching to it. There
>    is nothing specific about input #0
> 

This has been explained in another patch. Configuring 
CLK_OPS_PARENT_ENABLE can ensure that both channel 0 and channel 1 are 
enabled during mux switching. In fact, we only need to ensure that 
channel 0 is enabled.

>>
>>>> +     },
>>>> +};
>>>> +
>>>> +/* Channel 6 is gp1. */
>>>> +static u32 nna_parent_table[] = { 0, 1, 2, 3, 4, 5, 7};
>>>> +
>>>> +static const struct clk_parent_data nna_parent_data[] = {
>>>> +     { .fw_name = "oscin" },
>>>> +     { .fw_name = "fdiv2p5" },
>>>> +     { .fw_name = "fdiv4" },
>>>> +     { .fw_name = "fdiv3" },
>>>> +     { .fw_name = "fdiv5" },
>>>> +     { .fw_name = "fdiv2" },
>>>> +     { .fw_name = "hifi" }
>>>> +};
>

Patch

diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index 2a713276e46c..21845edcd8ef 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -146,6 +146,20 @@  config COMMON_CLK_A5_PLL
 	  Say Y if you want the board to work, because PLLs are the parent
 	  of most peripherals.
 
+config COMMON_CLK_A5_PERIPHERALS
+	tristate "Amlogic A5 peripherals clock controller"
+	depends on ARM64
+	default y
+	imply ARM_SCMI_PROTOCOL
+	imply COMMON_CLK_SCMI
+	imply COMMON_CLK_A5_PLL
+	select COMMON_CLK_MESON_REGMAP
+	select COMMON_CLK_MESON_DUALDIV
+	select COMMON_CLK_MESON_CLKC_UTILS
+	help
+	  Support for the Peripherals clock controller on Amlogic AV40x device,
+	  AKA A5. Say Y if you want the peripherals clock to work.
+
 config COMMON_CLK_C3_PLL
 	tristate "Amlogic C3 PLL clock controller"
 	depends on ARM64
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index fc4b8a723145..58236c6e8377 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -21,6 +21,7 @@  obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
 obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
 obj-$(CONFIG_COMMON_CLK_A1_PERIPHERALS) += a1-peripherals.o
 obj-$(CONFIG_COMMON_CLK_A5_PLL) += a5-pll.o
+obj-$(CONFIG_COMMON_CLK_A5_PERIPHERALS) += a5-peripherals.o
 obj-$(CONFIG_COMMON_CLK_C3_PLL) += c3-pll.o
 obj-$(CONFIG_COMMON_CLK_C3_PERIPHERALS) += c3-peripherals.o
 obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
diff --git a/drivers/clk/meson/a5-peripherals.c b/drivers/clk/meson/a5-peripherals.c
new file mode 100644
index 000000000000..c28da340a5af
--- /dev/null
+++ b/drivers/clk/meson/a5-peripherals.c
@@ -0,0 +1,1471 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Amlogic A5 Peripherals Clock Controller Driver
+ *
+ * Copyright (c) 2024 Amlogic, inc.
+ * Author: Chuan Liu <[e-mail]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/platform_device.h>
+#include "clk-regmap.h"
+#include "clk-dualdiv.h"
+#include "meson-clkc-utils.h"
+#include <dt-bindings/clock/amlogic,a5-peripherals-clkc.h>
+
+#define CLKCTRL_RTC_BY_OSCIN_CTRL0		0x8
+#define CLKCTRL_RTC_BY_OSCIN_CTRL1		0xc
+#define CLKCTRL_RTC_CTRL			0x10
+#define CLKCTRL_SYS_CLK_EN0_REG0		0x44
+#define CLKCTRL_SYS_CLK_EN0_REG1		0x48
+#define CLKCTRL_DSPA_CLK_CTRL0			0x9c
+#define CLKCTRL_CLK12_24_CTRL			0xa8
+#define CLKCTRL_AXI_CLK_EN0			0xac
+#define CLKCTRL_TS_CLK_CTRL			0x158
+#define CLKCTRL_ETH_CLK_CTRL			0x164
+#define CLKCTRL_NAND_CLK_CTRL			0x168
+#define CLKCTRL_SD_EMMC_CLK_CTRL		0x16c
+#define CLKCTRL_SPICC_CLK_CTRL			0x174
+#define CLKCTRL_GEN_CLK_CTRL			0x178
+#define CLKCTRL_SAR_CLK_CTRL0			0x17c
+#define CLKCTRL_PWM_CLK_AB_CTRL			0x180
+#define CLKCTRL_PWM_CLK_CD_CTRL			0x184
+#define CLKCTRL_PWM_CLK_EF_CTRL			0x188
+#define CLKCTRL_PWM_CLK_GH_CTRL			0x18c
+#define CLKCTRL_NNA_CLK_CNTL			0x220
+
+static struct clk_regmap rtc_xtal_clkin = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_RTC_BY_OSCIN_CTRL0,
+		.bit_idx = 31,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "rtc_xtal_clkin",
+		.ops = &clk_regmap_gate_ops,
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "oscin",
+		},
+		.num_parents = 1,
+	},
+};
+
+static const struct meson_clk_dualdiv_param rtc_32k_div_table[] = {
+	{ 733, 732, 8, 11, 1 },
+	{ /* sentinel */ }
+};
+
+static struct clk_regmap rtc_32k_div = {
+	.data = &(struct meson_clk_dualdiv_data) {
+		.n1 = {
+			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL0,
+			.shift   = 0,
+			.width   = 12,
+		},
+		.n2 = {
+			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL0,
+			.shift   = 12,
+			.width   = 12,
+		},
+		.m1 = {
+			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL1,
+			.shift   = 0,
+			.width   = 12,
+		},
+		.m2 = {
+			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL1,
+			.shift   = 12,
+			.width   = 12,
+		},
+		.dual = {
+			.reg_off = CLKCTRL_RTC_BY_OSCIN_CTRL0,
+			.shift   = 28,
+			.width   = 1,
+		},
+		.table = rtc_32k_div_table,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "rtc_32k_div",
+		.ops = &meson_clk_dualdiv_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&rtc_xtal_clkin.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static const struct clk_parent_data rtc_32k_mux_parent_data[] = {
+	{ .hw = &rtc_32k_div.hw },
+	{ .hw = &rtc_xtal_clkin.hw }
+};
+
+static struct clk_regmap rtc_32k_mux = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_RTC_BY_OSCIN_CTRL1,
+		.mask = 0x1,
+		.shift = 24,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "rtc_32k_mux",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = rtc_32k_mux_parent_data,
+		.num_parents = ARRAY_SIZE(rtc_32k_mux_parent_data),
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap rtc_32k = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_RTC_BY_OSCIN_CTRL0,
+		.bit_idx = 30,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "rtc_32k",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&rtc_32k_mux.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static const struct clk_parent_data rtc_clk_mux_parent_data[] = {
+	{ .fw_name = "oscin" },
+	{ .hw = &rtc_32k.hw },
+	{ .fw_name = "pad_osc" }
+};
+
+static struct clk_regmap rtc_clk = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_RTC_CTRL,
+		.mask = 0x3,
+		.shift = 0,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "rtc_clk",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = rtc_clk_mux_parent_data,
+		.num_parents = ARRAY_SIZE(rtc_clk_mux_parent_data),
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+#define A4_CLK_GATE(_name, _reg, _bit, _fw_name, _ops, _flags)		\
+struct clk_regmap _name = {						\
+	.data = &(struct clk_regmap_gate_data){				\
+		.offset = (_reg),					\
+		.bit_idx = (_bit),					\
+	},								\
+	.hw.init = &(struct clk_init_data) {				\
+		.name = #_name,						\
+		.ops = _ops,						\
+		.parent_data = &(const struct clk_parent_data) {	\
+			.fw_name = #_fw_name,				\
+		},							\
+		.num_parents = 1,					\
+		.flags = (_flags),					\
+	},								\
+}
+
+#define A4_SYS_GATE(_name, _reg, _bit, _flags)				\
+	A4_CLK_GATE(_name, _reg, _bit, sysclk,				\
+		    &clk_regmap_gate_ops, _flags)
+
+#define A4_SYS_GATE_RO(_name, _reg, _bit)				\
+	A4_CLK_GATE(_name, _reg, _bit, sysclk,				\
+		    &clk_regmap_gate_ro_ops, 0)
+
+static A4_SYS_GATE(sys_reset_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 1, 0);
+static A4_SYS_GATE(sys_pwr_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 3, 0);
+static A4_SYS_GATE(sys_pad_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 4, 0);
+static A4_SYS_GATE(sys_ctrl,		CLKCTRL_SYS_CLK_EN0_REG0, 5, 0);
+static A4_SYS_GATE(sys_ts_pll,		CLKCTRL_SYS_CLK_EN0_REG0, 6, 0);
+
+/*
+ * NOTE: sys_dev_arb provides the clock to the ETH and SPICC arbiters that
+ * access the AXI bus.
+ */
+static A4_SYS_GATE(sys_dev_arb,		CLKCTRL_SYS_CLK_EN0_REG0, 7, 0);
+
+/*
+ * FIXME: sys_mmc_pclk provides the clock for the DDR PHY, DDR will only be
+ * initialized in bl2, and this clock should not be touched in linux.
+ */
+static A4_SYS_GATE_RO(sys_mmc_pclk,	CLKCTRL_SYS_CLK_EN0_REG0, 8);
+static A4_SYS_GATE(sys_mailbox,		CLKCTRL_SYS_CLK_EN0_REG0, 10, 0);
+
+/*
+ * NOTE: sys_cpu_ctrl provides the clock for CPU controller. After clock is
+ * disabled, cpu_clk and other key CPU-related configurations cannot take effect.
+ */
+static A4_SYS_GATE(sys_cpu_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 11, CLK_IS_CRITICAL);
+static A4_SYS_GATE(sys_jtag_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 12, 0);
+static A4_SYS_GATE(sys_ir_ctrl,		CLKCTRL_SYS_CLK_EN0_REG0, 13, 0);
+
+/*
+ * NOTE: sys_irq_ctrl provides the clock for IRQ controller. The IRQ controller
+ * collects and distributes the interrupt signal to the GIC, PWR_CTRL, and
+ * AOCPU. If the clock is disabled, interrupt-related functions will occurs an
+ * exception.
+ */
+static A4_SYS_GATE(sys_irq_ctrl,	CLKCTRL_SYS_CLK_EN0_REG0, 14, CLK_IS_CRITICAL);
+static A4_SYS_GATE(sys_msr_clk,		CLKCTRL_SYS_CLK_EN0_REG0, 15, 0);
+static A4_SYS_GATE(sys_rom,		CLKCTRL_SYS_CLK_EN0_REG0, 16, 0);
+static A4_SYS_GATE(sys_cpu_apb,		CLKCTRL_SYS_CLK_EN0_REG0, 18, 0);
+static A4_SYS_GATE(sys_rsa,		CLKCTRL_SYS_CLK_EN0_REG0, 19, 0);
+static A4_SYS_GATE(sys_sar_adc,		CLKCTRL_SYS_CLK_EN0_REG0, 20, 0);
+static A4_SYS_GATE(sys_startup,		CLKCTRL_SYS_CLK_EN0_REG0, 21, 0);
+static A4_SYS_GATE(sys_secure,		CLKCTRL_SYS_CLK_EN0_REG0, 22, 0);
+static A4_SYS_GATE(sys_spifc,		CLKCTRL_SYS_CLK_EN0_REG0, 23, 0);
+static A4_SYS_GATE(sys_dspa,		CLKCTRL_SYS_CLK_EN0_REG0, 24, 0);
+static A4_SYS_GATE(sys_nna,		CLKCTRL_SYS_CLK_EN0_REG0, 25, 0);
+static A4_SYS_GATE(sys_eth_mac,		CLKCTRL_SYS_CLK_EN0_REG0, 26, 0);
+
+/*
+ * FIXME: sys_gic provides the clock for GIC(Generic Interrupt Controller).
+ * After clock is disabled, The GIC cannot work properly. At present, the driver
+ * used by our GIC is the public driver in kernel, and there is no management
+ * clock in the driver.
+ */
+static A4_SYS_GATE(sys_gic,		CLKCTRL_SYS_CLK_EN0_REG0, 27, CLK_IS_CRITICAL);
+static A4_SYS_GATE(sys_rama,		CLKCTRL_SYS_CLK_EN0_REG0, 28, 0);
+
+/*
+ * NOTE: sys_big_nic provides the clock to the control bus of the NIC(Network
+ * Interface Controller) between multiple devices(CPU, DDR, RAM, ROM, GIC,
+ * SPIFC, CAPU, JTAG, EMMC, SDIO, sec_top, USB, Audio, ETH, SPICC) in the
+ * system. After clock is disabled, The NIC cannot work.
+ */
+static A4_SYS_GATE(sys_big_nic,		CLKCTRL_SYS_CLK_EN0_REG0, 29, CLK_IS_CRITICAL);
+static A4_SYS_GATE(sys_ramb,		CLKCTRL_SYS_CLK_EN0_REG0, 30, 0);
+static A4_SYS_GATE(sys_audio_top,	CLKCTRL_SYS_CLK_EN0_REG1, 0, 0);
+static A4_SYS_GATE(sys_audio_vad,	CLKCTRL_SYS_CLK_EN0_REG1, 1, 0);
+static A4_SYS_GATE(sys_usb,		CLKCTRL_SYS_CLK_EN0_REG1, 2, 0);
+static A4_SYS_GATE(sys_sd_emmc_a,	CLKCTRL_SYS_CLK_EN0_REG1, 3, 0);
+static A4_SYS_GATE(sys_sd_emmc_c,	CLKCTRL_SYS_CLK_EN0_REG1, 4, 0);
+static A4_SYS_GATE(sys_pwm_ab,		CLKCTRL_SYS_CLK_EN0_REG1, 5, 0);
+static A4_SYS_GATE(sys_pwm_cd,		CLKCTRL_SYS_CLK_EN0_REG1, 6, 0);
+static A4_SYS_GATE(sys_pwm_ef,		CLKCTRL_SYS_CLK_EN0_REG1, 7, 0);
+static A4_SYS_GATE(sys_pwm_gh,		CLKCTRL_SYS_CLK_EN0_REG1, 8, 0);
+static A4_SYS_GATE(sys_spicc_1,		CLKCTRL_SYS_CLK_EN0_REG1, 9, 0);
+static A4_SYS_GATE(sys_spicc_0,		CLKCTRL_SYS_CLK_EN0_REG1, 10, 0);
+static A4_SYS_GATE(sys_uart_a,		CLKCTRL_SYS_CLK_EN0_REG1, 11, 0);
+static A4_SYS_GATE(sys_uart_b,		CLKCTRL_SYS_CLK_EN0_REG1, 12, 0);
+static A4_SYS_GATE(sys_uart_c,		CLKCTRL_SYS_CLK_EN0_REG1, 13, 0);
+static A4_SYS_GATE(sys_uart_d,		CLKCTRL_SYS_CLK_EN0_REG1, 14, 0);
+static A4_SYS_GATE(sys_uart_e,		CLKCTRL_SYS_CLK_EN0_REG1, 15, 0);
+static A4_SYS_GATE(sys_i2c_m_a,		CLKCTRL_SYS_CLK_EN0_REG1, 16, 0);
+static A4_SYS_GATE(sys_i2c_m_b,		CLKCTRL_SYS_CLK_EN0_REG1, 17, 0);
+static A4_SYS_GATE(sys_i2c_m_c,		CLKCTRL_SYS_CLK_EN0_REG1, 18, 0);
+static A4_SYS_GATE(sys_i2c_m_d,		CLKCTRL_SYS_CLK_EN0_REG1, 19, 0);
+static A4_SYS_GATE(sys_rtc,		CLKCTRL_SYS_CLK_EN0_REG1, 21, 0);
+
+#define A4_AXI_GATE(_name, _reg, _bit, _flags)				\
+	A4_CLK_GATE(_name, _reg, _bit, axiclk,				\
+		    &clk_regmap_gate_ops, _flags)
+
+static A4_AXI_GATE(axi_audio_vad,	CLKCTRL_AXI_CLK_EN0, 0, 0);
+static A4_AXI_GATE(axi_audio_top,	CLKCTRL_AXI_CLK_EN0, 1, 0);
+
+/*
+ * NOTE: axi_sys_nic provides the clock to the AXI bus of the system NIC. After
+ * clock is disabled, The NIC cannot work.
+ */
+static A4_AXI_GATE(axi_sys_nic,		CLKCTRL_AXI_CLK_EN0, 2, CLK_IS_CRITICAL);
+static A4_AXI_GATE(axi_ramb,		CLKCTRL_AXI_CLK_EN0, 5, 0);
+static A4_AXI_GATE(axi_rama,		CLKCTRL_AXI_CLK_EN0, 6, 0);
+
+/*
+ * NOTE: axi_cpu_dmc provides the clock to the AXI bus where the CPU accesses
+ * the DDR. After clock is disabled, The CPU will not have access to the DDR.
+ */
+static A4_AXI_GATE(axi_cpu_dmc,		CLKCTRL_AXI_CLK_EN0, 7, CLK_IS_CRITICAL);
+static A4_AXI_GATE(axi_nna,		CLKCTRL_AXI_CLK_EN0, 12, 0);
+
+/*
+ * NOTE: axi_dev1_dmc provides the clock for the peripherals(EMMC, SDIO,
+ * sec_top, USB, Audio) to access the AXI bus of the DDR.
+ */
+static A4_AXI_GATE(axi_dev1_dmc,	CLKCTRL_AXI_CLK_EN0, 13, 0);
+
+/*
+ * NOTE: axi_dev0_dmc provides the clock for the peripherals(ETH and SPICC)
+ * to access the AXI bus of the DDR.
+ */
+static A4_AXI_GATE(axi_dev0_dmc,	CLKCTRL_AXI_CLK_EN0, 14, 0);
+static A4_AXI_GATE(axi_dsp_dmc,		CLKCTRL_AXI_CLK_EN0, 15, 0);
+
+static struct clk_regmap clk_12_24m_in = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_CLK12_24_CTRL,
+		.bit_idx = 11,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "clk_12_24m_in",
+		.ops = &clk_regmap_gate_ops,
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "xtal_24m",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap clk_12_24m = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_CLK12_24_CTRL,
+		.shift = 10,
+		.width = 1,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "clk_12_24m",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&clk_12_24m_in.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+/* FIXME: set value 0 will div by 2 like value 1 */
+static struct clk_regmap fclk_25m_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_CLK12_24_CTRL,
+		.shift = 0,
+		.width = 8,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "fclk_25m_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "fix",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap fclk_25m = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_CLK12_24_CTRL,
+		.bit_idx = 12,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "fclk_25m",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&fclk_25m_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+/*
+ * Channel 3(ddr_dpll_pt_clk) is manged by the DDR module; channel 12(cts_msr_clk)
+ * is manged by clock measures module. Their hardware are out of clock tree.
+ * Channel 4 5 8 9 10 11 13 14 15 16 18 are not connected.
+ *
+ * gp1 is designed for DSU (DynamIQ Shared Unit) alone. It cannot be changed
+ * arbitrarily. gp1 is read-only in the kernel and is only open for debug purposes.
+ */
+static u32 gen_parent_table[] = { 0, 1, 2, 6, 7, 17, 19, 20, 21, 22, 23, 24, 25,
+				  26, 27, 28};
+
+static const struct clk_parent_data gen_parent_data[] = {
+	{ .fw_name = "oscin" },
+	{ .hw = &rtc_clk.hw },
+	{ .fw_name = "sysplldiv16" },
+	{ .fw_name = "gp1" },
+	{ .fw_name = "hifi" },
+	{ .fw_name = "cpudiv16" },
+	{ .fw_name = "fdiv2" },
+	{ .fw_name = "fdiv2p5" },
+	{ .fw_name = "fdiv3" },
+	{ .fw_name = "fdiv4" },
+	{ .fw_name = "fdiv5" },
+	{ .fw_name = "fdiv7" },
+	{ .fw_name = "mpll0" },
+	{ .fw_name = "mpll1" },
+	{ .fw_name = "mpll2" },
+	{ .fw_name = "mpll3" }
+};
+
+static struct clk_regmap gen_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_GEN_CLK_CTRL,
+		.mask = 0x1f,
+		.shift = 12,
+		.table = gen_parent_table,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "gen_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = gen_parent_data,
+		.num_parents = ARRAY_SIZE(gen_parent_data),
+	},
+};
+
+static struct clk_regmap gen_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_GEN_CLK_CTRL,
+		.shift = 0,
+		.width = 11,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "gen_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&gen_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap gen = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_GEN_CLK_CTRL,
+		.bit_idx = 11,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "gen",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&gen_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static const struct clk_parent_data saradc_parent_data[] = {
+	{ .fw_name = "oscin" },
+	{ .fw_name = "sysclk" }
+};
+
+static struct clk_regmap saradc_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_SAR_CLK_CTRL0,
+		.mask = 0x1,
+		.shift = 9,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "saradc_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = saradc_parent_data,
+		.num_parents = ARRAY_SIZE(saradc_parent_data),
+	},
+};
+
+static struct clk_regmap saradc_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_SAR_CLK_CTRL0,
+		.shift = 0,
+		.width = 8,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "saradc_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&saradc_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap saradc = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_SAR_CLK_CTRL0,
+		.bit_idx = 8,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "saradc",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&saradc_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static const struct clk_parent_data pwm_parent_data[] = {
+	{ .fw_name = "oscin" },
+	{ .hw = &rtc_clk.hw },
+	{ .fw_name = "fdiv4" },
+	{ .fw_name = "fdiv3" }
+};
+
+#define AML_PWM_CLK_MUX(_name, _reg, _shift) {			\
+	.data = &(struct clk_regmap_mux_data) {			\
+		.offset = _reg,					\
+		.mask = 0x3,					\
+		.shift = _shift,				\
+	},							\
+	.hw.init = &(struct clk_init_data) {			\
+		.name = #_name "_sel",				\
+		.ops = &clk_regmap_mux_ops,			\
+		.parent_data = pwm_parent_data,			\
+		.num_parents = ARRAY_SIZE(pwm_parent_data),	\
+	},							\
+}
+
+#define AML_PWM_CLK_DIV(_name, _reg, _shift) {			\
+	.data = &(struct clk_regmap_div_data) {			\
+		.offset = _reg,					\
+		.shift = _shift,				\
+		.width = 8,					\
+	},							\
+	.hw.init = &(struct clk_init_data) {			\
+		.name = #_name "_div",				\
+		.ops = &clk_regmap_divider_ops,			\
+		.parent_names = (const char *[]) { #_name "_sel" },\
+		.num_parents = 1,				\
+		.flags = CLK_SET_RATE_PARENT,			\
+	},							\
+}
+
+#define AML_PWM_CLK_GATE(_name, _reg, _bit) {			\
+	.data = &(struct clk_regmap_gate_data) {		\
+		.offset = _reg,					\
+		.bit_idx = _bit,				\
+	},							\
+	.hw.init = &(struct clk_init_data) {			\
+		.name = #_name,					\
+		.ops = &clk_regmap_gate_ops,			\
+		.parent_names = (const char *[]) { #_name "_div" },\
+		.num_parents = 1,				\
+		.flags = CLK_SET_RATE_PARENT,			\
+	},							\
+}
+
+static struct clk_regmap pwm_a_sel =
+	AML_PWM_CLK_MUX(pwm_a, CLKCTRL_PWM_CLK_AB_CTRL, 9);
+static struct clk_regmap pwm_a_div =
+	AML_PWM_CLK_DIV(pwm_a, CLKCTRL_PWM_CLK_AB_CTRL, 0);
+static struct clk_regmap pwm_a =
+	AML_PWM_CLK_GATE(pwm_a, CLKCTRL_PWM_CLK_AB_CTRL, 8);
+
+static struct clk_regmap pwm_b_sel =
+	AML_PWM_CLK_MUX(pwm_b, CLKCTRL_PWM_CLK_AB_CTRL, 25);
+static struct clk_regmap pwm_b_div =
+	AML_PWM_CLK_DIV(pwm_b, CLKCTRL_PWM_CLK_AB_CTRL, 16);
+static struct clk_regmap pwm_b =
+	AML_PWM_CLK_GATE(pwm_b, CLKCTRL_PWM_CLK_AB_CTRL, 24);
+
+static struct clk_regmap pwm_c_sel =
+	AML_PWM_CLK_MUX(pwm_c, CLKCTRL_PWM_CLK_CD_CTRL, 9);
+static struct clk_regmap pwm_c_div =
+	AML_PWM_CLK_DIV(pwm_c, CLKCTRL_PWM_CLK_CD_CTRL, 0);
+static struct clk_regmap pwm_c =
+	AML_PWM_CLK_GATE(pwm_c, CLKCTRL_PWM_CLK_CD_CTRL, 8);
+
+static struct clk_regmap pwm_d_sel =
+	AML_PWM_CLK_MUX(pwm_d, CLKCTRL_PWM_CLK_CD_CTRL, 25);
+static struct clk_regmap pwm_d_div =
+	AML_PWM_CLK_DIV(pwm_d, CLKCTRL_PWM_CLK_CD_CTRL, 16);
+static struct clk_regmap pwm_d =
+	AML_PWM_CLK_GATE(pwm_d, CLKCTRL_PWM_CLK_CD_CTRL, 24);
+
+static struct clk_regmap pwm_e_sel =
+	AML_PWM_CLK_MUX(pwm_e, CLKCTRL_PWM_CLK_EF_CTRL, 9);
+static struct clk_regmap pwm_e_div =
+	AML_PWM_CLK_DIV(pwm_e, CLKCTRL_PWM_CLK_EF_CTRL, 0);
+static struct clk_regmap pwm_e =
+	AML_PWM_CLK_GATE(pwm_e, CLKCTRL_PWM_CLK_EF_CTRL, 8);
+
+static struct clk_regmap pwm_f_sel =
+	AML_PWM_CLK_MUX(pwm_f, CLKCTRL_PWM_CLK_EF_CTRL, 25);
+static struct clk_regmap pwm_f_div =
+	AML_PWM_CLK_DIV(pwm_f, CLKCTRL_PWM_CLK_EF_CTRL, 16);
+static struct clk_regmap pwm_f =
+	AML_PWM_CLK_GATE(pwm_f, CLKCTRL_PWM_CLK_EF_CTRL, 24);
+
+static struct clk_regmap pwm_g_sel =
+	AML_PWM_CLK_MUX(pwm_g, CLKCTRL_PWM_CLK_GH_CTRL, 9);
+static struct clk_regmap pwm_g_div =
+	AML_PWM_CLK_DIV(pwm_g, CLKCTRL_PWM_CLK_GH_CTRL, 0);
+static struct clk_regmap pwm_g =
+	AML_PWM_CLK_GATE(pwm_g, CLKCTRL_PWM_CLK_GH_CTRL, 8);
+
+static struct clk_regmap pwm_h_sel =
+	AML_PWM_CLK_MUX(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 25);
+static struct clk_regmap pwm_h_div =
+	AML_PWM_CLK_DIV(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 16);
+static struct clk_regmap pwm_h =
+	AML_PWM_CLK_GATE(pwm_h, CLKCTRL_PWM_CLK_GH_CTRL, 24);
+
+/* Channel 7 is gp1. */
+static const struct clk_parent_data spicc_parent_data[] = {
+	{ .fw_name = "oscin" },
+	{ .fw_name = "sysclk" },
+	{ .fw_name = "fdiv4" },
+	{ .fw_name = "fdiv3" },
+	{ .fw_name = "fdiv2" },
+	{ .fw_name = "fdiv5" },
+	{ .fw_name = "fdiv7" }
+};
+
+static struct clk_regmap spicc_0_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_SPICC_CLK_CTRL,
+		.mask = 0x7,
+		.shift = 7,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "spicc_0_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = spicc_parent_data,
+		.num_parents = ARRAY_SIZE(spicc_parent_data),
+	},
+};
+
+static struct clk_regmap spicc_0_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_SPICC_CLK_CTRL,
+		.shift = 0,
+		.width = 6,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "spicc_0_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&spicc_0_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap spicc_0 = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_SPICC_CLK_CTRL,
+		.bit_idx = 6,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "spicc_0",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&spicc_0_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap spicc_1_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_SPICC_CLK_CTRL,
+		.mask = 0x7,
+		.shift = 23,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "spicc_1_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = spicc_parent_data,
+		.num_parents = ARRAY_SIZE(spicc_parent_data),
+	},
+};
+
+static struct clk_regmap spicc_1_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_SPICC_CLK_CTRL,
+		.shift = 16,
+		.width = 6,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "spicc_1_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&spicc_1_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap spicc_1 = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_SPICC_CLK_CTRL,
+		.bit_idx = 22,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "spicc_1",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&spicc_1_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static const struct clk_parent_data emmc_parent_data[] = {
+	{ .fw_name = "oscin" },
+	{ .fw_name = "fdiv2" },
+	{ .fw_name = "fdiv3" },
+	{ .fw_name = "hifi" },
+	{ .fw_name = "fdiv2p5" },
+	{ .fw_name = "mpll2" },
+	{ .fw_name = "mpll3" },
+	{ .fw_name = "gp0" }
+};
+
+static struct clk_regmap sd_emmc_a_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_SD_EMMC_CLK_CTRL,
+		.mask = 0x7,
+		.shift = 9,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "sd_emmc_a_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = emmc_parent_data,
+		.num_parents = ARRAY_SIZE(emmc_parent_data),
+	},
+};
+
+static struct clk_regmap sd_emmc_a_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_SD_EMMC_CLK_CTRL,
+		.shift = 0,
+		.width = 7,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "sd_emmc_a_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&sd_emmc_a_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap sd_emmc_a = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_SD_EMMC_CLK_CTRL,
+		.bit_idx = 7,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "sd_emmc_a",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&sd_emmc_a_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap sd_emmc_c_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_NAND_CLK_CTRL,
+		.mask = 0x7,
+		.shift = 9,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "sd_emmc_c_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = emmc_parent_data,
+		.num_parents = ARRAY_SIZE(emmc_parent_data),
+	},
+};
+
+static struct clk_regmap sd_emmc_c_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_NAND_CLK_CTRL,
+		.shift = 0,
+		.width = 7,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "sd_emmc_c_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&sd_emmc_c_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap sd_emmc_c = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_NAND_CLK_CTRL,
+		.bit_idx = 7,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "sd_emmc_c",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&sd_emmc_c_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap ts_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_TS_CLK_CTRL,
+		.shift = 0,
+		.width = 8,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "ts_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "oscin",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap ts = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_TS_CLK_CTRL,
+		.bit_idx = 8,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "ts",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&ts_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_fixed_factor eth_125m_div = {
+	.mult = 1,
+	.div = 8,
+	.hw.init = &(struct clk_init_data) {
+		.name = "eth_125m_div",
+		.ops = &clk_fixed_factor_ops,
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "fdiv2",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap eth_125m = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_ETH_CLK_CTRL,
+		.bit_idx = 7,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "eth_125m",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&eth_125m_div.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap eth_rmii_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_ETH_CLK_CTRL,
+		.shift = 0,
+		.width = 7,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "eth_rmii_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "fdiv2",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap eth_rmii = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_ETH_CLK_CTRL,
+		.bit_idx = 8,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "eth_rmii",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&eth_rmii_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+/* Channel 6 is gp1. */
+static u32 dspa_parent_table[] = { 0, 1, 2, 3, 4, 5, 7};
+
+static const struct clk_parent_data dspa_parent_data[] = {
+	{ .fw_name = "oscin" },
+	{ .fw_name = "fdiv2p5" },
+	{ .fw_name = "fdiv3" },
+	{ .fw_name = "rtc" },
+	{ .fw_name = "hifi" },
+	{ .fw_name = "fdiv4" },
+	{ .hw = &rtc_clk.hw }
+};
+
+static struct clk_regmap dspa_0_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_DSPA_CLK_CTRL0,
+		.mask = 0x7,
+		.shift = 10,
+		.table = dspa_parent_table,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "dspa_0_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = dspa_parent_data,
+		.num_parents = ARRAY_SIZE(dspa_parent_data),
+	},
+};
+
+static struct clk_regmap dspa_0_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_DSPA_CLK_CTRL0,
+		.shift = 0,
+		.width = 10,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "dspa_0_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&dspa_0_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap dspa_0 = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_DSPA_CLK_CTRL0,
+		.bit_idx = 13,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "dspa_0",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&dspa_0_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap dspa_1_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_DSPA_CLK_CTRL0,
+		.mask = 0x7,
+		.shift = 26,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "dspa_1_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = dspa_parent_data,
+		.num_parents = ARRAY_SIZE(dspa_parent_data),
+	},
+};
+
+static struct clk_regmap dspa_1_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_DSPA_CLK_CTRL0,
+		.shift = 16,
+		.width = 10,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "dspa_1_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&dspa_1_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap dspa_1 = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_DSPA_CLK_CTRL0,
+		.bit_idx = 29,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "dspa_1",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&dspa_1_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap dspa = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = CLKCTRL_DSPA_CLK_CTRL0,
+		.mask = 0x1,
+		.shift = 15,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "dspa",
+		.ops = &clk_regmap_mux_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&dspa_0.hw,
+			&dspa_1.hw
+		},
+		.num_parents = 2,
+		/*
+		 * NOTE: This level of mux is "no glitch mux", and mux_0
+		 * (here dspa_0) is not only the clock source for mux, but also
+		 * provides a working clock for "no glitch mux". "no glitch mux"
+		 * can be switched only when mux_0 has a clock input. Therefore,
+		 * add flag CLK_OPS_PARENT_ENABLE to ensure that mux_0 has clock
+		 * when "no glitch mux" works.
+		 */
+		.flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
+	},
+};
+
+/* Channel 6 is gp1. */
+static u32 nna_parent_table[] = { 0, 1, 2, 3, 4, 5, 7};
+
+static const struct clk_parent_data nna_parent_data[] = {
+	{ .fw_name = "oscin" },
+	{ .fw_name = "fdiv2p5" },
+	{ .fw_name = "fdiv4" },
+	{ .fw_name = "fdiv3" },
+	{ .fw_name = "fdiv5" },
+	{ .fw_name = "fdiv2" },
+	{ .fw_name = "hifi" }
+};
+
+static struct clk_regmap nna_core_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_NNA_CLK_CNTL,
+		.mask = 0x7,
+		.shift = 9,
+		.table = nna_parent_table,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "nna_core_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = nna_parent_data,
+		.num_parents = ARRAY_SIZE(nna_parent_data),
+	},
+};
+
+static struct clk_regmap nna_core_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_NNA_CLK_CNTL,
+		.shift = 0,
+		.width = 7,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "nna_core_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&nna_core_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap nna_core = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_NNA_CLK_CNTL,
+		.bit_idx = 8,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "nna_core",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&nna_core_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap nna_axi_sel = {
+	.data = &(struct clk_regmap_mux_data) {
+		.offset = CLKCTRL_NNA_CLK_CNTL,
+		.mask = 0x7,
+		.shift = 25,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "nna_axi_sel",
+		.ops = &clk_regmap_mux_ops,
+		.parent_data = nna_parent_data,
+		.num_parents = ARRAY_SIZE(nna_parent_data),
+	},
+};
+
+static struct clk_regmap nna_axi_div = {
+	.data = &(struct clk_regmap_div_data) {
+		.offset = CLKCTRL_NNA_CLK_CNTL,
+		.shift = 16,
+		.width = 7,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "nna_axi_div",
+		.ops = &clk_regmap_divider_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&nna_axi_sel.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_regmap nna_axi = {
+	.data = &(struct clk_regmap_gate_data) {
+		.offset = CLKCTRL_NNA_CLK_CNTL,
+		.bit_idx = 24,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "nna_axi",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&nna_axi_div.hw
+		},
+		.num_parents = 1,
+		.flags = CLK_SET_RATE_PARENT,
+	},
+};
+
+static struct clk_hw *a5_periphs_hw_clks[] = {
+	[CLKID_RTC_XTAL_CLKIN]		= &rtc_xtal_clkin.hw,
+	[CLKID_RTC_32K_DIV]		= &rtc_32k_div.hw,
+	[CLKID_RTC_32K_MUX]		= &rtc_32k_mux.hw,
+	[CLKID_RTC_32K]			= &rtc_32k.hw,
+	[CLKID_RTC_CLK]			= &rtc_clk.hw,
+	[CLKID_SYS_RESET_CTRL]		= &sys_reset_ctrl.hw,
+	[CLKID_SYS_PWR_CTRL]		= &sys_pwr_ctrl.hw,
+	[CLKID_SYS_PAD_CTRL]		= &sys_pad_ctrl.hw,
+	[CLKID_SYS_CTRL]		= &sys_ctrl.hw,
+	[CLKID_SYS_TS_PLL]		= &sys_ts_pll.hw,
+	[CLKID_SYS_DEV_ARB]		= &sys_dev_arb.hw,
+	[CLKID_SYS_MMC_PCLK]		= &sys_mmc_pclk.hw,
+	[CLKID_SYS_MAILBOX]		= &sys_mailbox.hw,
+	[CLKID_SYS_CPU_CTRL]		= &sys_cpu_ctrl.hw,
+	[CLKID_SYS_JTAG_CTRL]		= &sys_jtag_ctrl.hw,
+	[CLKID_SYS_IR_CTRL]		= &sys_ir_ctrl.hw,
+	[CLKID_SYS_IRQ_CTRL]		= &sys_irq_ctrl.hw,
+	[CLKID_SYS_MSR_CLK]		= &sys_msr_clk.hw,
+	[CLKID_SYS_ROM]			= &sys_rom.hw,
+	[CLKID_SYS_CPU_ARB]		= &sys_cpu_apb.hw,
+	[CLKID_SYS_RSA]			= &sys_rsa.hw,
+	[CLKID_SYS_SAR_ADC]		= &sys_sar_adc.hw,
+	[CLKID_SYS_STARTUP]		= &sys_startup.hw,
+	[CLKID_SYS_SECURE]		= &sys_secure.hw,
+	[CLKID_SYS_SPIFC]		= &sys_spifc.hw,
+	[CLKID_SYS_DSPA]		= &sys_dspa.hw,
+	[CLKID_SYS_NNA]			= &sys_nna.hw,
+	[CLKID_SYS_ETH_MAC]		= &sys_eth_mac.hw,
+	[CLKID_SYS_GIC]			= &sys_gic.hw,
+	[CLKID_SYS_RAMA]		= &sys_rama.hw,
+	[CLKID_SYS_BIG_NIC]		= &sys_big_nic.hw,
+	[CLKID_SYS_RAMB]		= &sys_ramb.hw,
+	[CLKID_SYS_AUDIO_TOP]		= &sys_audio_top.hw,
+	[CLKID_SYS_AUDIO_VAD]		= &sys_audio_vad.hw,
+	[CLKID_SYS_USB]			= &sys_usb.hw,
+	[CLKID_SYS_SD_EMMC_A]		= &sys_sd_emmc_a.hw,
+	[CLKID_SYS_SD_EMMC_C]		= &sys_sd_emmc_c.hw,
+	[CLKID_SYS_PWM_AB]		= &sys_pwm_ab.hw,
+	[CLKID_SYS_PWM_CD]		= &sys_pwm_cd.hw,
+	[CLKID_SYS_PWM_EF]		= &sys_pwm_ef.hw,
+	[CLKID_SYS_PWM_GH]		= &sys_pwm_gh.hw,
+	[CLKID_SYS_SPICC_1]		= &sys_spicc_1.hw,
+	[CLKID_SYS_SPICC_0]		= &sys_spicc_0.hw,
+	[CLKID_SYS_UART_A]		= &sys_uart_a.hw,
+	[CLKID_SYS_UART_B]		= &sys_uart_b.hw,
+	[CLKID_SYS_UART_C]		= &sys_uart_c.hw,
+	[CLKID_SYS_UART_D]		= &sys_uart_d.hw,
+	[CLKID_SYS_UART_E]		= &sys_uart_e.hw,
+	[CLKID_SYS_I2C_M_A]		= &sys_i2c_m_a.hw,
+	[CLKID_SYS_I2C_M_B]		= &sys_i2c_m_b.hw,
+	[CLKID_SYS_I2C_M_C]		= &sys_i2c_m_c.hw,
+	[CLKID_SYS_I2C_M_D]		= &sys_i2c_m_d.hw,
+	[CLKID_SYS_RTC]			= &sys_rtc.hw,
+	[CLKID_AXI_AUDIO_VAD]		= &axi_audio_vad.hw,
+	[CLKID_AXI_AUDIO_TOP]		= &axi_audio_top.hw,
+	[CLKID_AXI_SYS_NIC]		= &axi_sys_nic.hw,
+	[CLKID_AXI_RAMB]		= &axi_ramb.hw,
+	[CLKID_AXI_RAMA]		= &axi_rama.hw,
+	[CLKID_AXI_CPU_DMC]		= &axi_cpu_dmc.hw,
+	[CLKID_AXI_NNA]			= &axi_nna.hw,
+	[CLKID_AXI_DEV1_DMC]		= &axi_dev1_dmc.hw,
+	[CLKID_AXI_DEV0_DMC]		= &axi_dev0_dmc.hw,
+	[CLKID_AXI_DSP_DMC]		= &axi_dsp_dmc.hw,
+	[CLKID_12_24M_IN]		= &clk_12_24m_in.hw,
+	[CLKID_12M_24M]			= &clk_12_24m.hw,
+	[CLKID_FCLK_25M_DIV]		= &fclk_25m_div.hw,
+	[CLKID_FCLK_25M]		= &fclk_25m.hw,
+	[CLKID_GEN_SEL]			= &gen_sel.hw,
+	[CLKID_GEN_DIV]			= &gen_div.hw,
+	[CLKID_GEN]			= &gen.hw,
+	[CLKID_SARADC_SEL]		= &saradc_sel.hw,
+	[CLKID_SARADC_DIV]		= &saradc_div.hw,
+	[CLKID_SARADC]			= &saradc.hw,
+	[CLKID_PWM_A_SEL]		= &pwm_a_sel.hw,
+	[CLKID_PWM_A_DIV]		= &pwm_a_div.hw,
+	[CLKID_PWM_A]			= &pwm_a.hw,
+	[CLKID_PWM_B_SEL]		= &pwm_b_sel.hw,
+	[CLKID_PWM_B_DIV]		= &pwm_b_div.hw,
+	[CLKID_PWM_B]			= &pwm_b.hw,
+	[CLKID_PWM_C_SEL]		= &pwm_c_sel.hw,
+	[CLKID_PWM_C_DIV]		= &pwm_c_div.hw,
+	[CLKID_PWM_C]			= &pwm_c.hw,
+	[CLKID_PWM_D_SEL]		= &pwm_d_sel.hw,
+	[CLKID_PWM_D_DIV]		= &pwm_d_div.hw,
+	[CLKID_PWM_D]			= &pwm_d.hw,
+	[CLKID_PWM_E_SEL]		= &pwm_e_sel.hw,
+	[CLKID_PWM_E_DIV]		= &pwm_e_div.hw,
+	[CLKID_PWM_E]			= &pwm_e.hw,
+	[CLKID_PWM_F_SEL]		= &pwm_f_sel.hw,
+	[CLKID_PWM_F_DIV]		= &pwm_f_div.hw,
+	[CLKID_PWM_F]			= &pwm_f.hw,
+	[CLKID_PWM_G_SEL]		= &pwm_g_sel.hw,
+	[CLKID_PWM_G_DIV]		= &pwm_g_div.hw,
+	[CLKID_PWM_G]			= &pwm_g.hw,
+	[CLKID_PWM_H_SEL]		= &pwm_h_sel.hw,
+	[CLKID_PWM_H_DIV]		= &pwm_h_div.hw,
+	[CLKID_PWM_H]			= &pwm_h.hw,
+	[CLKID_SPICC_0_SEL]		= &spicc_0_sel.hw,
+	[CLKID_SPICC_0_DIV]		= &spicc_0_div.hw,
+	[CLKID_SPICC_0]			= &spicc_0.hw,
+	[CLKID_SPICC_1_SEL]		= &spicc_1_sel.hw,
+	[CLKID_SPICC_1_DIV]		= &spicc_1_div.hw,
+	[CLKID_SPICC_1]			= &spicc_1.hw,
+	[CLKID_SD_EMMC_A_SEL]		= &sd_emmc_a_sel.hw,
+	[CLKID_SD_EMMC_A_DIV]		= &sd_emmc_a_div.hw,
+	[CLKID_SD_EMMC_A]		= &sd_emmc_a.hw,
+	[CLKID_SD_EMMC_C_SEL]		= &sd_emmc_c_sel.hw,
+	[CLKID_SD_EMMC_C_DIV]		= &sd_emmc_c_div.hw,
+	[CLKID_SD_EMMC_C]		= &sd_emmc_c.hw,
+	[CLKID_TS_DIV]			= &ts_div.hw,
+	[CLKID_TS]			= &ts.hw,
+	[CLKID_ETH_125M_DIV]		= &eth_125m_div.hw,
+	[CLKID_ETH_125M]		= &eth_125m.hw,
+	[CLKID_ETH_RMII_DIV]		= &eth_rmii_div.hw,
+	[CLKID_ETH_RMII]		= &eth_rmii.hw,
+	[CLKID_DSPA_0_SEL]		= &dspa_0_sel.hw,
+	[CLKID_DSPA_0_DIV]		= &dspa_0_div.hw,
+	[CLKID_DSPA_0]			= &dspa_0.hw,
+	[CLKID_DSPA_1_SEL]		= &dspa_1_sel.hw,
+	[CLKID_DSPA_1_DIV]		= &dspa_1_div.hw,
+	[CLKID_DSPA_1]			= &dspa_1.hw,
+	[CLKID_DSPA]			= &dspa.hw,
+	[CLKID_NNA_CORE_SEL]		= &nna_core_sel.hw,
+	[CLKID_NNA_CORE_DIV]		= &nna_core_div.hw,
+	[CLKID_NNA_CORE]		= &nna_core.hw,
+	[CLKID_NNA_AXI_SEL]		= &nna_axi_sel.hw,
+	[CLKID_NNA_AXI_DIV]		= &nna_axi_div.hw,
+	[CLKID_NNA_AXI]			= &nna_axi.hw,
+};
+
+/* Convenience table to populate regmap in .probe */
+static struct clk_regmap *const a5_periphs_clk_regmaps[] = {
+	&rtc_xtal_clkin,
+	&rtc_32k_div,
+	&rtc_32k_mux,
+	&rtc_32k,
+	&rtc_clk,
+	&sys_reset_ctrl,
+	&sys_pwr_ctrl,
+	&sys_pad_ctrl,
+	&sys_ctrl,
+	&sys_ts_pll,
+	&sys_dev_arb,
+	&sys_mmc_pclk,
+	&sys_mailbox,
+	&sys_cpu_ctrl,
+	&sys_jtag_ctrl,
+	&sys_ir_ctrl,
+	&sys_irq_ctrl,
+	&sys_msr_clk,
+	&sys_rom,
+	&sys_cpu_apb,
+	&sys_rsa,
+	&sys_sar_adc,
+	&sys_startup,
+	&sys_secure,
+	&sys_spifc,
+	&sys_dspa,
+	&sys_nna,
+	&sys_eth_mac,
+	&sys_gic,
+	&sys_rama,
+	&sys_big_nic,
+	&sys_ramb,
+	&sys_audio_top,
+	&sys_audio_vad,
+	&sys_usb,
+	&sys_sd_emmc_a,
+	&sys_sd_emmc_c,
+	&sys_pwm_ab,
+	&sys_pwm_cd,
+	&sys_pwm_ef,
+	&sys_pwm_gh,
+	&sys_spicc_1,
+	&sys_spicc_0,
+	&sys_uart_a,
+	&sys_uart_b,
+	&sys_uart_c,
+	&sys_uart_d,
+	&sys_uart_e,
+	&sys_i2c_m_a,
+	&sys_i2c_m_b,
+	&sys_i2c_m_c,
+	&sys_i2c_m_d,
+	&sys_rtc,
+	&axi_audio_vad,
+	&axi_audio_top,
+	&axi_sys_nic,
+	&axi_ramb,
+	&axi_rama,
+	&axi_cpu_dmc,
+	&axi_nna,
+	&axi_dev1_dmc,
+	&axi_dev0_dmc,
+	&axi_dsp_dmc,
+	&clk_12_24m_in,
+	&clk_12_24m,
+	&fclk_25m_div,
+	&fclk_25m,
+	&gen_sel,
+	&gen_div,
+	&gen,
+	&saradc_sel,
+	&saradc_div,
+	&saradc,
+	&pwm_a_sel,
+	&pwm_a_div,
+	&pwm_a,
+	&pwm_b_sel,
+	&pwm_b_div,
+	&pwm_b,
+	&pwm_c_sel,
+	&pwm_c_div,
+	&pwm_c,
+	&pwm_d_sel,
+	&pwm_d_div,
+	&pwm_d,
+	&pwm_e_sel,
+	&pwm_e_div,
+	&pwm_e,
+	&pwm_f_sel,
+	&pwm_f_div,
+	&pwm_f,
+	&pwm_g_sel,
+	&pwm_g_div,
+	&pwm_g,
+	&pwm_h_sel,
+	&pwm_h_div,
+	&pwm_h,
+	&spicc_0_sel,
+	&spicc_0_div,
+	&spicc_0,
+	&spicc_1_sel,
+	&spicc_1_div,
+	&spicc_1,
+	&sd_emmc_a_sel,
+	&sd_emmc_a_div,
+	&sd_emmc_a,
+	&sd_emmc_c_sel,
+	&sd_emmc_c_div,
+	&sd_emmc_c,
+	&ts_div,
+	&ts,
+	&eth_125m,
+	&eth_rmii_div,
+	&eth_rmii,
+	&dspa_0_sel,
+	&dspa_0_div,
+	&dspa_0,
+	&dspa_1_sel,
+	&dspa_1_div,
+	&dspa_1,
+	&dspa,
+	&nna_core_sel,
+	&nna_core_div,
+	&nna_core,
+	&nna_axi_sel,
+	&nna_axi_div,
+	&nna_axi
+};
+
+static const struct regmap_config clkc_regmap_config = {
+	.reg_bits       = 32,
+	.val_bits       = 32,
+	.reg_stride     = 4,
+	.max_register   = CLKCTRL_NNA_CLK_CNTL,
+};
+
+static struct meson_clk_hw_data a5_periphs_clks = {
+	.hws = a5_periphs_hw_clks,
+	.num = ARRAY_SIZE(a5_periphs_hw_clks),
+};
+
+static int aml_a5_peripherals_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct regmap *regmap;
+	void __iomem *base;
+	int clkid, ret, i;
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	regmap = devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	/* Populate regmap for the regmap backed clocks */
+	for (i = 0; i < ARRAY_SIZE(a5_periphs_clk_regmaps); i++)
+		a5_periphs_clk_regmaps[i]->map = regmap;
+
+	for (clkid = 0; clkid < a5_periphs_clks.num; clkid++) {
+		/* array might be sparse */
+		if (!a5_periphs_clks.hws[clkid])
+			continue;
+
+		ret = devm_clk_hw_register(dev, a5_periphs_clks.hws[clkid]);
+		if (ret) {
+			dev_err(dev, "Clock registration failed\n");
+			return ret;
+		}
+	}
+
+	return devm_of_clk_add_hw_provider(dev, meson_clk_hw_get,
+					   &a5_periphs_clks);
+}
+
+static const struct of_device_id a5_peripherals_clkc_match_table[] = {
+	{
+		.compatible = "amlogic,a5-peripherals-clkc",
+	},
+	{ /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, a5_peripherals_clkc_match_table);
+
+static struct platform_driver a5_peripherals_driver = {
+	.probe		= aml_a5_peripherals_probe,
+	.driver		= {
+		.name	= "a5-peripherals-clkc",
+		.of_match_table = a5_peripherals_clkc_match_table,
+	},
+};
+module_platform_driver(a5_peripherals_driver);
+
+MODULE_DESCRIPTION("Amlogic A5 Peripherals Clock Controller driver");
+MODULE_AUTHOR("Chuan Liu <[e-mail]>");
+MODULE_LICENSE("GPL");