@@ -17,3 +17,13 @@ config NET_DSA_MV88E6XXX_PTP
help
Say Y to enable PTP hardware timestamping on Marvell 88E6xxx switch
chips that support it.
+
+config NET_DSA_MV88E6XXX_LEDS
+ bool "LED support for Marvell 88E6xxx"
+ default y
+ depends on NET_DSA_MV88E6XXX
+ depends on LEDS_CLASS=y || LEDS_CLASS=NET_DSA_MV88E6XXX
+ depends on LEDS_TRIGGERS
+ help
+ This enabled support for controlling the LEDs attached to the
+ Marvell 88E6xxx switch chips.
@@ -9,6 +9,7 @@ mv88e6xxx-objs += global2.o
mv88e6xxx-objs += global2_avb.o
mv88e6xxx-objs += global2_scratch.o
mv88e6xxx-$(CONFIG_NET_DSA_MV88E6XXX_PTP) += hwtstamp.o
+mv88e6xxx-$(CONFIG_NET_DSA_MV88E6XXX_LEDS) += leds.o
mv88e6xxx-objs += pcs-6185.o
mv88e6xxx-objs += pcs-6352.o
mv88e6xxx-objs += pcs-639x.o
@@ -27,6 +27,7 @@
#include <linux/of_irq.h>
#include <linux/of_mdio.h>
#include <linux/platform_data/mv88e6xxx.h>
+#include <linux/property.h>
#include <linux/netdevice.h>
#include <linux/gpio/consumer.h>
#include <linux/phylink.h>
@@ -3371,14 +3372,43 @@ static int mv88e6xxx_setup_upstream_port(struct mv88e6xxx_chip *chip, int port)
static int mv88e6xxx_setup_port(struct mv88e6xxx_chip *chip, int port)
{
struct device_node *phy_handle = NULL;
+ struct fwnode_handle *ports_fwnode;
+ struct fwnode_handle *port_fwnode;
struct dsa_switch *ds = chip->ds;
+ struct mv88e6xxx_port *p;
struct dsa_port *dp;
int tx_amp;
int err;
u16 reg;
+ u32 val;
+
+ p = &chip->ports[port];
+ p->chip = chip;
+ p->port = port;
+
+ /* Look up corresponding fwnode if any */
+ ports_fwnode = device_get_named_child_node(chip->dev, "ethernet-ports");
+ if (!ports_fwnode)
+ ports_fwnode = device_get_named_child_node(chip->dev, "ports");
+ if (ports_fwnode) {
+ fwnode_for_each_child_node(ports_fwnode, port_fwnode) {
+ if (fwnode_property_read_u32(port_fwnode, "reg", &val))
+ continue;
+ if (val == port) {
+ p->fwnode = port_fwnode;
+ p->fiber = fwnode_property_present(port_fwnode, "sfp");
+ break;
+ }
+ }
+ } else {
+ dev_dbg(chip->dev, "no ethernet ports node defined for the device\n");
+ }
- chip->ports[port].chip = chip;
- chip->ports[port].port = port;
+ if (chip->info->ops->port_setup_leds) {
+ err = chip->info->ops->port_setup_leds(chip, port);
+ if (err && err != -EOPNOTSUPP)
+ return err;
+ }
err = mv88e6xxx_port_setup_mac(chip, port, LINK_UNFORCED,
SPEED_UNFORCED, DUPLEX_UNFORCED,
@@ -5396,6 +5426,7 @@ static const struct mv88e6xxx_ops mv88e6352_ops = {
.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
.port_get_cmode = mv88e6352_port_get_cmode,
+ .port_setup_leds = mv88e6xxx_port_setup_leds,
.port_setup_message_port = mv88e6xxx_setup_message_port,
.stats_snapshot = mv88e6320_g1_stats_snapshot,
.stats_set_histogram = mv88e6095_g1_stats_set_histogram,
@@ -13,7 +13,9 @@
#include <linux/irq.h>
#include <linux/gpio/consumer.h>
#include <linux/kthread.h>
+#include <linux/leds.h>
#include <linux/phy.h>
+#include <linux/property.h>
#include <linux/ptp_clock_kernel.h>
#include <linux/timecounter.h>
#include <net/dsa.h>
@@ -275,6 +277,7 @@ struct mv88e6xxx_vlan {
struct mv88e6xxx_port {
struct mv88e6xxx_chip *chip;
int port;
+ struct fwnode_handle *fwnode;
struct mv88e6xxx_vlan bridge_pvid;
u64 serdes_stats[2];
u64 atu_member_violation;
@@ -289,6 +292,11 @@ struct mv88e6xxx_port {
struct devlink_region *region;
void *pcs_private;
+ /* LED related information */
+ bool fiber;
+ struct led_classdev led0;
+ struct led_classdev led1;
+
/* MacAuth Bypass control flag */
bool mab;
};
@@ -572,6 +580,9 @@ struct mv88e6xxx_ops {
phy_interface_t mode);
int (*port_get_cmode)(struct mv88e6xxx_chip *chip, int port, u8 *cmode);
+ /* LED control */
+ int (*port_setup_leds)(struct mv88e6xxx_chip *chip, int port);
+
/* Some devices have a per port register indicating what is
* the upstream port this port should forward to.
*/
new file mode 100644
@@ -0,0 +1,844 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+#include <linux/bitfield.h>
+#include <linux/leds.h>
+#include <linux/property.h>
+
+#include "chip.h"
+#include "global2.h"
+#include "port.h"
+
+/* Offset 0x16: LED control */
+
+static int mv88e6xxx_port_led_write(struct mv88e6xxx_chip *chip, int port, u16 reg)
+{
+ reg |= MV88E6XXX_PORT_LED_CONTROL_UPDATE;
+
+ return mv88e6xxx_port_write(chip, port, MV88E6XXX_PORT_LED_CONTROL, reg);
+}
+
+static int mv88e6xxx_port_led_read(struct mv88e6xxx_chip *chip, int port,
+ u16 ptr, u16 *val)
+{
+ int err;
+
+ err = mv88e6xxx_port_write(chip, port, MV88E6XXX_PORT_LED_CONTROL, ptr);
+ if (err)
+ return err;
+
+ err = mv88e6xxx_port_read(chip, port, MV88E6XXX_PORT_LED_CONTROL, val);
+ *val &= 0x3ff;
+
+ return err;
+}
+
+static int mv88e6xxx_led_brightness_set(struct mv88e6xxx_port *p, int led,
+ int brightness)
+{
+ u16 reg;
+ int err;
+
+ err = mv88e6xxx_port_led_read(p->chip, p->port,
+ MV88E6XXX_PORT_LED_CONTROL_POINTER_LED01_CTRL,
+ ®);
+ if (err)
+ return err;
+
+ if (led == 1)
+ reg &= ~MV88E6XXX_PORT_LED_CONTROL_LED1_SEL_MASK;
+ else
+ reg &= ~MV88E6XXX_PORT_LED_CONTROL_LED0_SEL_MASK;
+
+ if (brightness) {
+ /* Selector 0x0f == Force LED ON */
+ if (led == 1)
+ reg |= MV88E6XXX_PORT_LED_CONTROL_LED1_SELF;
+ else
+ reg |= MV88E6XXX_PORT_LED_CONTROL_LED0_SELF;
+ } else {
+ /* Selector 0x0e == Force LED OFF */
+ if (led == 1)
+ reg |= MV88E6XXX_PORT_LED_CONTROL_LED1_SELE;
+ else
+ reg |= MV88E6XXX_PORT_LED_CONTROL_LED0_SELE;
+ }
+
+ reg |= MV88E6XXX_PORT_LED_CONTROL_POINTER_LED01_CTRL;
+
+ return mv88e6xxx_port_led_write(p->chip, p->port, reg);
+}
+
+static int mv88e6xxx_led0_brightness_set_blocking(struct led_classdev *ldev,
+ enum led_brightness brightness)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led0);
+ int err;
+
+ mv88e6xxx_reg_lock(p->chip);
+ err = mv88e6xxx_led_brightness_set(p, 0, brightness);
+ mv88e6xxx_reg_unlock(p->chip);
+
+ return err;
+}
+
+static int mv88e6xxx_led1_brightness_set_blocking(struct led_classdev *ldev,
+ enum led_brightness brightness)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led1);
+ int err;
+
+ mv88e6xxx_reg_lock(p->chip);
+ err = mv88e6xxx_led_brightness_set(p, 1, brightness);
+ mv88e6xxx_reg_unlock(p->chip);
+
+ return err;
+}
+
+struct mv88e6xxx_led_hwconfig {
+ int led;
+ u8 portmask;
+ unsigned long rules;
+ bool fiber;
+ bool blink_activity;
+ u16 selector;
+};
+
+/* The following is a lookup table to check what rules we can support on a
+ * certain LED given restrictions such as that some rules only work with fiber
+ * (SFP) connections and some blink on activity by default.
+ */
+#define MV88E6XXX_PORTS_0_3 (BIT(0) | BIT(1) | BIT(2) | BIT(3))
+#define MV88E6XXX_PORTS_4_5 (BIT(4) | BIT(5))
+#define MV88E6XXX_PORT_4 BIT(4)
+#define MV88E6XXX_PORT_5 BIT(5)
+
+/* Entries are listed in selector order.
+ *
+ * These configurations vary across different switch families, list
+ * different tables per-family here.
+ */
+static const struct mv88e6xxx_led_hwconfig mv88e6352_led_hwconfigs[] = {
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORT_4,
+ .rules = BIT(TRIGGER_NETDEV_LINK),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL0,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORT_5,
+ .rules = BIT(TRIGGER_NETDEV_LINK_1000),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL0,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_100) | BIT(TRIGGER_NETDEV_LINK_1000),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL1,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK_100),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL1,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_4_5,
+ .rules = BIT(TRIGGER_NETDEV_LINK_100),
+ .blink_activity = true,
+ .fiber = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL1,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_4_5,
+ .rules = BIT(TRIGGER_NETDEV_LINK_1000),
+ .blink_activity = true,
+ .fiber = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL1,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_1000),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL2,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK_100),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL2,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_4_5,
+ .rules = BIT(TRIGGER_NETDEV_LINK_1000),
+ .blink_activity = true,
+ .fiber = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL2,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_4_5,
+ .rules = BIT(TRIGGER_NETDEV_LINK_100),
+ .blink_activity = true,
+ .fiber = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL2,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL3,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_1000),
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL3,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_4_5,
+ .rules = BIT(TRIGGER_NETDEV_LINK),
+ .fiber = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL3,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORT_4,
+ .rules = BIT(TRIGGER_NETDEV_LINK),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL4,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORT_5,
+ .rules = BIT(TRIGGER_NETDEV_LINK),
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL5,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_FULL_DUPLEX),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL6,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK_1000),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL6,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORT_4,
+ .rules = BIT(TRIGGER_NETDEV_FULL_DUPLEX),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL6,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORT_5,
+ .rules = BIT(TRIGGER_NETDEV_FULL_DUPLEX),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL6,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK_1000),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL7,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK_1000),
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL7,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK),
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL8,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL8,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORT_5,
+ .rules = BIT(TRIGGER_NETDEV_LINK),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL8,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_10),
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SEL9,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_100),
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SEL9,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_10),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SELA,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_100),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SELA,
+ },
+ {
+ .led = 0,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_100) | BIT(TRIGGER_NETDEV_LINK_1000),
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED0_SELB,
+ },
+ {
+ .led = 1,
+ .portmask = MV88E6XXX_PORTS_0_3,
+ .rules = BIT(TRIGGER_NETDEV_LINK_100) | BIT(TRIGGER_NETDEV_LINK_1000),
+ .blink_activity = true,
+ .selector = MV88E6XXX_PORT_LED_CONTROL_LED1_SELB,
+ },
+};
+
+/* mv88e6xxx_led_match_selector() - look up the appropriate LED mode selector
+ * @p: port state container
+ * @led: LED number, 0 or 1
+ * @blink_activity: blink the LED (usually blink on indicated activity)
+ * @fiber: the link is connected to fiber such as SFP
+ * @rules: LED status flags from the LED classdev core
+ * @selector: fill in the selector in this parameter with an OR operation
+ */
+static int mv88e6xxx_led_match_selector(struct mv88e6xxx_port *p, int led, bool blink_activity,
+ bool fiber, unsigned long rules, u16 *selector)
+{
+ const struct mv88e6xxx_led_hwconfig *conf;
+ int i;
+
+ /* No rules means we turn the LED off */
+ if (!rules) {
+ if (led == 1)
+ *selector |= MV88E6XXX_PORT_LED_CONTROL_LED1_SELE;
+ else
+ *selector |= MV88E6XXX_PORT_LED_CONTROL_LED0_SELE;
+ return 0;
+ }
+
+ /* TODO: these rules are for MV88E6352, when adding other families,
+ * think abour making sure you select the table that match the
+ * specific switch family.
+ */
+ for (i = 0; i < ARRAY_SIZE(mv88e6352_led_hwconfigs); i++) {
+ conf = &mv88e6352_led_hwconfigs[i];
+
+ if (conf->led != led)
+ continue;
+
+ if (!(conf->portmask & BIT(p->port)))
+ continue;
+
+ if (conf->blink_activity != blink_activity)
+ continue;
+
+ if (conf->fiber != fiber)
+ continue;
+
+ if (conf->rules == rules) {
+ dev_dbg(p->chip->dev, "port%d LED %d set selector %04x for rules %08lx\n",
+ p->port, led, conf->selector, rules);
+ *selector |= conf->selector;
+ return 0;
+ }
+ }
+
+ return -EOPNOTSUPP;
+}
+
+/* mv88e6xxx_led_match_selector() - find Linux netdev rules from a selector value
+ * @p: port state container
+ * @selector: the selector value from the LED actity register
+ * @led: LED number, 0 or 1
+ * @rules: Linux netdev activity rules found from selector
+ */
+static int
+mv88e6xxx_led_match_rule(struct mv88e6xxx_port *p, u16 selector, int led, unsigned long *rules)
+{
+ const struct mv88e6xxx_led_hwconfig *conf;
+ int i;
+
+ /* Find the selector in the table, we just look for the right selector
+ * and ignore if the activity has special properties such as blinking
+ * or is fiber-only.
+ */
+ for (i = 0; i < ARRAY_SIZE(mv88e6352_led_hwconfigs); i++) {
+ conf = &mv88e6352_led_hwconfigs[i];
+
+ if (conf->led != led)
+ continue;
+
+ if (!(conf->portmask & BIT(p->port)))
+ continue;
+
+ if (conf->selector == selector) {
+ dev_dbg(p->chip->dev, "port%d LED %d has selector %04x, rules %08lx\n",
+ p->port, led, selector, conf->rules);
+ *rules = conf->rules;
+ return 0;
+ }
+ }
+
+ return -EINVAL;
+}
+
+/* mv88e6xxx_led_get_selector() - get the appropriate LED mode selector
+ * @p: port state container
+ * @led: LED number, 0 or 1
+ * @fiber: the link is connected to fiber such as SFP
+ * @rules: LED status flags from the LED classdev core
+ * @selector: fill in the selector in this parameter with an OR operation
+ */
+static int mv88e6xxx_led_get_selector(struct mv88e6xxx_port *p, int led,
+ bool fiber, unsigned long rules, u16 *selector)
+{
+ int err;
+
+ /* What happens here is that we first try to locate a trigger with solid
+ * indicator (such as LED is on for a 1000 link) else we try a second
+ * sweep to find something suitable with a trigger that will blink on
+ * activity.
+ */
+ err = mv88e6xxx_led_match_selector(p, led, false, fiber, rules, selector);
+ if (err)
+ return mv88e6xxx_led_match_selector(p, led, true, fiber, rules, selector);
+
+ return 0;
+}
+
+/* Sets up the hardware blinking period */
+static int mv88e6xxx_led_set_blinking_period(struct mv88e6xxx_port *p, int led,
+ unsigned long delay_on, unsigned long delay_off)
+{
+ unsigned long period;
+ u16 reg;
+
+ period = delay_on + delay_off;
+
+ reg = 0;
+
+ switch (period) {
+ case 21:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_21MS;
+ break;
+ case 42:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_42MS;
+ break;
+ case 84:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_84MS;
+ break;
+ case 168:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_168MS;
+ break;
+ case 336:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_336MS;
+ break;
+ case 672:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_672MS;
+ break;
+ default:
+ /* Fall back to software blinking */
+ return -EINVAL;
+ }
+
+ /* This is essentially PWM duty cycle: how long time of the period
+ * will the LED be on. Zero isn't great in most cases.
+ */
+ switch (delay_on) {
+ case 0:
+ /* This is usually pretty useless and will make the LED look OFF */
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_NONE;
+ break;
+ case 21:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_21MS;
+ break;
+ case 42:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_42MS;
+ break;
+ case 84:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_84MS;
+ break;
+ case 168:
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_168MS;
+ break;
+ default:
+ /* Just use something non-zero */
+ reg |= MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_21MS;
+ break;
+ }
+
+ /* Set up blink rate */
+ reg |= MV88E6XXX_PORT_LED_CONTROL_POINTER_STRETCH_BLINK;
+
+ return mv88e6xxx_port_led_write(p->chip, p->port, reg);
+}
+
+static int mv88e6xxx_led_blink_set(struct mv88e6xxx_port *p, int led,
+ unsigned long *delay_on, unsigned long *delay_off)
+{
+ u16 reg;
+ int err;
+
+ /* Choose a sensible default 336 ms (~3 Hz) */
+ if ((*delay_on == 0) && (*delay_off == 0)) {
+ *delay_on = 168;
+ *delay_off = 168;
+ }
+
+ /* No off delay is just on */
+ if (*delay_off == 0)
+ return mv88e6xxx_led_brightness_set(p, led, 1);
+
+ err = mv88e6xxx_led_set_blinking_period(p, led, *delay_on, *delay_off);
+ if (err)
+ return err;
+
+ err = mv88e6xxx_port_led_read(p->chip, p->port,
+ MV88E6XXX_PORT_LED_CONTROL_POINTER_LED01_CTRL,
+ ®);
+ if (err)
+ return err;
+
+ if (led == 1)
+ reg &= ~MV88E6XXX_PORT_LED_CONTROL_LED1_SEL_MASK;
+ else
+ reg &= ~MV88E6XXX_PORT_LED_CONTROL_LED0_SEL_MASK;
+
+ /* This will select the forced blinking status */
+ if (led == 1)
+ reg |= MV88E6XXX_PORT_LED_CONTROL_LED1_SELD;
+ else
+ reg |= MV88E6XXX_PORT_LED_CONTROL_LED0_SELD;
+
+ reg |= MV88E6XXX_PORT_LED_CONTROL_POINTER_LED01_CTRL;
+
+ return mv88e6xxx_port_led_write(p->chip, p->port, reg);
+}
+
+static int mv88e6xxx_led0_blink_set(struct led_classdev *ldev,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led0);
+ int err;
+
+ mv88e6xxx_reg_lock(p->chip);
+ err = mv88e6xxx_led_blink_set(p, 0, delay_on, delay_off);
+ mv88e6xxx_reg_unlock(p->chip);
+
+ return err;
+}
+
+static int mv88e6xxx_led1_blink_set(struct led_classdev *ldev,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led1);
+ int err;
+
+ mv88e6xxx_reg_lock(p->chip);
+ err = mv88e6xxx_led_blink_set(p, 1, delay_on, delay_off);
+ mv88e6xxx_reg_unlock(p->chip);
+
+ return err;
+}
+
+static int
+mv88e6xxx_led0_hw_control_is_supported(struct led_classdev *ldev, unsigned long rules)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led0);
+ u16 selector = 0;
+
+ return mv88e6xxx_led_get_selector(p, 0, p->fiber, rules, &selector);
+}
+
+static int
+mv88e6xxx_led1_hw_control_is_supported(struct led_classdev *ldev, unsigned long rules)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led1);
+ u16 selector = 0;
+
+ return mv88e6xxx_led_get_selector(p, 1, p->fiber, rules, &selector);
+}
+
+static int mv88e6xxx_led_hw_control_set(struct mv88e6xxx_port *p,
+ int led, unsigned long rules)
+{
+ u16 reg;
+ int err;
+
+ err = mv88e6xxx_port_led_read(p->chip, p->port,
+ MV88E6XXX_PORT_LED_CONTROL_POINTER_LED01_CTRL,
+ ®);
+ if (err)
+ return err;
+
+ if (led == 1)
+ reg &= ~MV88E6XXX_PORT_LED_CONTROL_LED1_SEL_MASK;
+ else
+ reg &= ~MV88E6XXX_PORT_LED_CONTROL_LED0_SEL_MASK;
+
+ err = mv88e6xxx_led_get_selector(p, led, p->fiber, rules, ®);
+ if (err)
+ return err;
+
+ reg |= MV88E6XXX_PORT_LED_CONTROL_POINTER_LED01_CTRL;
+
+ if (led == 0)
+ dev_dbg(p->chip->dev, "LED 0 hw control on port %d trigger selector 0x%02x\n",
+ p->port,
+ (unsigned int)(reg & MV88E6XXX_PORT_LED_CONTROL_LED0_SEL_MASK));
+ else
+ dev_dbg(p->chip->dev, "LED 1 hw control on port %d trigger selector 0x%02x\n",
+ p->port,
+ (unsigned int)(reg & MV88E6XXX_PORT_LED_CONTROL_LED1_SEL_MASK) >> 4);
+
+ return mv88e6xxx_port_led_write(p->chip, p->port, reg);
+}
+
+static int
+mv88e6xxx_led_hw_control_get(struct mv88e6xxx_port *p, int led, unsigned long *rules)
+{
+ u16 val;
+ int err;
+
+ mv88e6xxx_reg_lock(p->chip);
+ err = mv88e6xxx_port_led_read(p->chip, p->port,
+ MV88E6XXX_PORT_LED_CONTROL_POINTER_LED01_CTRL, &val);
+ mv88e6xxx_reg_unlock(p->chip);
+ if (err)
+ return err;
+
+ /* Mask out the selector bits for this port */
+ if (led == 1) {
+ val &= MV88E6XXX_PORT_LED_CONTROL_LED1_SEL_MASK;
+ /* It's forced blinking/OFF/ON */
+ if (val == MV88E6XXX_PORT_LED_CONTROL_LED1_SELD ||
+ val == MV88E6XXX_PORT_LED_CONTROL_LED1_SELE ||
+ val == MV88E6XXX_PORT_LED_CONTROL_LED1_SELF) {
+ *rules = 0;
+ return 0;
+ }
+ } else {
+ val &= MV88E6XXX_PORT_LED_CONTROL_LED0_SEL_MASK;
+ /* It's forced blinking/OFF/ON */
+ if (val == MV88E6XXX_PORT_LED_CONTROL_LED0_SELD ||
+ val == MV88E6XXX_PORT_LED_CONTROL_LED0_SELE ||
+ val == MV88E6XXX_PORT_LED_CONTROL_LED0_SELF) {
+ *rules = 0;
+ return 0;
+ }
+ }
+
+ err = mv88e6xxx_led_match_rule(p, val, led, rules);
+ if (!err)
+ return 0;
+
+ dev_dbg(p->chip->dev, "couldn't find matching selector for %04x\n", val);
+ *rules = 0;
+ return 0;
+}
+
+static int
+mv88e6xxx_led0_hw_control_set(struct led_classdev *ldev, unsigned long rules)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led0);
+ int err;
+
+ mv88e6xxx_reg_lock(p->chip);
+ err = mv88e6xxx_led_hw_control_set(p, 0, rules);
+ mv88e6xxx_reg_unlock(p->chip);
+
+ return err;
+}
+
+static int
+mv88e6xxx_led1_hw_control_set(struct led_classdev *ldev, unsigned long rules)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led1);
+ int err;
+
+ mv88e6xxx_reg_lock(p->chip);
+ err = mv88e6xxx_led_hw_control_set(p, 1, rules);
+ mv88e6xxx_reg_unlock(p->chip);
+
+ return err;
+}
+
+static int
+mv88e6xxx_led0_hw_control_get(struct led_classdev *ldev, unsigned long *rules)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led0);
+
+ return mv88e6xxx_led_hw_control_get(p, 0, rules);
+}
+
+static int
+mv88e6xxx_led1_hw_control_get(struct led_classdev *ldev, unsigned long *rules)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led1);
+
+ return mv88e6xxx_led_hw_control_get(p, 1, rules);
+}
+
+static struct device *mv88e6xxx_led_hw_control_get_device(struct mv88e6xxx_port *p)
+{
+ struct dsa_port *dp;
+
+ dp = dsa_to_port(p->chip->ds, p->port);
+ if (!dp)
+ return NULL;
+ if (dp->user)
+ return &dp->user->dev;
+ return NULL;
+}
+
+static struct device *
+mv88e6xxx_led0_hw_control_get_device(struct led_classdev *ldev)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led0);
+
+ return mv88e6xxx_led_hw_control_get_device(p);
+}
+
+static struct device *
+mv88e6xxx_led1_hw_control_get_device(struct led_classdev *ldev)
+{
+ struct mv88e6xxx_port *p = container_of(ldev, struct mv88e6xxx_port, led1);
+
+ return mv88e6xxx_led_hw_control_get_device(p);
+}
+
+int mv88e6xxx_port_setup_leds(struct mv88e6xxx_chip *chip, int port)
+{
+ struct fwnode_handle *led = NULL, *leds = NULL;
+ struct led_init_data init_data = { };
+ unsigned long delay_off = 168;
+ unsigned long delay_on = 168;
+ enum led_default_state state;
+ struct mv88e6xxx_port *p;
+ struct led_classdev *l;
+ struct device *dev;
+ u32 led_num;
+ int ret;
+
+ /* LEDs are on ports 1,2,3,4, 5 and 6 (index 0..5), no more */
+ if (port > 5)
+ return -EOPNOTSUPP;
+
+ p = &chip->ports[port];
+ if (!p->fwnode)
+ return 0;
+
+ dev = chip->dev;
+
+ leds = fwnode_get_named_child_node(p->fwnode, "leds");
+ if (!leds) {
+ dev_dbg(dev, "No Leds node specified in device tree for port %d!\n",
+ port);
+ return 0;
+ }
+
+ fwnode_for_each_child_node(leds, led) {
+ /* Reg represent the led number of the port, max 2
+ * LEDs can be connected to each port, in some designs
+ * only one LED is connected.
+ */
+ if (fwnode_property_read_u32(led, "reg", &led_num))
+ continue;
+ if (led_num > 1) {
+ dev_err(dev, "invalid LED specified port %d\n", port);
+ return -EINVAL;
+ }
+
+ if (led_num == 0)
+ l = &p->led0;
+ else
+ l = &p->led1;
+
+ state = led_init_default_state_get(led);
+ switch (state) {
+ case LEDS_DEFSTATE_ON:
+ l->brightness = 1;
+ mv88e6xxx_led_brightness_set(p, led_num, 1);
+ break;
+ case LEDS_DEFSTATE_KEEP:
+ break;
+ default:
+ l->brightness = 0;
+ mv88e6xxx_led_brightness_set(p, led_num, 0);
+ }
+
+ /* Default blinking period for LEDs */
+ mv88e6xxx_led_set_blinking_period(p, led_num, delay_on, delay_off);
+
+ l->max_brightness = 1;
+ if (led_num == 0) {
+ l->brightness_set_blocking = mv88e6xxx_led0_brightness_set_blocking;
+ l->blink_set = mv88e6xxx_led0_blink_set;
+ l->hw_control_is_supported = mv88e6xxx_led0_hw_control_is_supported;
+ l->hw_control_set = mv88e6xxx_led0_hw_control_set;
+ l->hw_control_get = mv88e6xxx_led0_hw_control_get;
+ l->hw_control_get_device = mv88e6xxx_led0_hw_control_get_device;
+ } else {
+ l->brightness_set_blocking = mv88e6xxx_led1_brightness_set_blocking;
+ l->blink_set = mv88e6xxx_led1_blink_set;
+ l->hw_control_is_supported = mv88e6xxx_led1_hw_control_is_supported;
+ l->hw_control_set = mv88e6xxx_led1_hw_control_set;
+ l->hw_control_get = mv88e6xxx_led1_hw_control_get;
+ l->hw_control_get_device = mv88e6xxx_led1_hw_control_get_device;
+ }
+ l->hw_control_trigger = "netdev";
+
+ init_data.default_label = ":port";
+ init_data.fwnode = led;
+ init_data.devname_mandatory = true;
+ init_data.devicename = kasprintf(GFP_KERNEL, "%s:0%d:0%d", chip->info->name,
+ port, led_num);
+ if (!init_data.devicename)
+ return -ENOMEM;
+
+ ret = devm_led_classdev_register_ext(dev, l, &init_data);
+ kfree(init_data.devicename);
+
+ if (ret) {
+ dev_err(dev, "Failed to init LED %d for port %d", led_num, port);
+ return ret;
+ }
+ }
+
+ return 0;
+}
@@ -12,6 +12,7 @@
#include <linux/if_bridge.h>
#include <linux/phy.h>
#include <linux/phylink.h>
+#include <linux/property.h>
#include "chip.h"
#include "global2.h"
@@ -309,6 +309,130 @@
/* Offset 0x13: OutFiltered Counter */
#define MV88E6XXX_PORT_OUT_FILTERED 0x13
+/* Offset 0x16: LED Control */
+#define MV88E6XXX_PORT_LED_CONTROL 0x16
+#define MV88E6XXX_PORT_LED_CONTROL_UPDATE BIT(15)
+#define MV88E6XXX_PORT_LED_CONTROL_POINTER_MASK GENMASK(14, 12)
+#define MV88E6XXX_PORT_LED_CONTROL_POINTER_LED01_CTRL (0x00 << 12) /* Control for LED 0 and 1 */
+#define MV88E6XXX_PORT_LED_CONTROL_POINTER_STRETCH_BLINK (0x06 << 12) /* Stetch and Blink Rate */
+#define MV88E6XXX_PORT_LED_CONTROL_POINTER_CNTL_SPECIAL (0x07 << 12) /* Control for the Port's Special LED */
+#define MV88E6XXX_PORT_LED_CONTROL_DATA_MASK GENMASK(10, 0)
+/* Selection masks valid for either port 1,2,3,4 or 5 */
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL_MASK GENMASK(3, 0)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL_MASK GENMASK(7, 4)
+/* Selection control for LED 0 and 1, ports 5 and 6 only has LED 0
+ * Bits Function
+ * 0..3 LED 0 control selector on ports 1-5
+ * 4..7 LED 1 control selector on ports 1-4 on port 5 this controls LED 0 of port 6
+ *
+ * Sel Port LED Function
+ * 0 1-4 0 Link/Act/Speed by Blink Rate (off=no link, on=link, blink=activity, blink speed=link speed)
+ * 1-4 1 Port 2's Special LED
+ * 5-6 0 Port 5 Link/Act (off=no link, on=link, blink=activity)
+ * 5-6 1 Port 6 Link/Act (off=no link, on=link 1000, blink=activity)
+ * 1 1-4 0 100/1000 Link/Act (off=no link, on=100 or 1000 link, blink=activity)
+ * 1-4 1 10/100 Link Act (off=no link, on=10 or 100 link, blink=activity)
+ * 5-6 0 Fiber 100 Link/Act (off=no link, on=link 100, blink=activity)
+ * 5-6 1 Fiber 1000 Link/Act (off=no link, on=link 1000, blink=activity)
+ * 2 1-4 0 1000 Link/Act (off=no link, on=link 1000, blink=activity)
+ * 1-4 1 10/100 Link/Act (off=no link, on=10 or 100 link, blink=activity)
+ * 5-6 0 Fiber 1000 Link/Act (off=no link, on=link 1000, blink=activity)
+ * 5-6 1 Fiber 100 Link/Act (off=no link, on=link 100, blink=activity)
+ * 3 1-4 0 Link/Act (off=no link, on=link, blink=activity)
+ * 1-4 1 1000 Link (off=no link, on=1000 link)
+ * 5-6 0 Port 0's Special LED
+ * 5-6 1 Fiber Link (off=no link, on=link)
+ * 4 1-4 0 Port 0's Special LED
+ * 1-4 1 Port 1's Special LED
+ * 5-6 0 Port 1's Special LED
+ * 5-6 1 Port 5 Link/Act (off=no link, on=link, blink=activity)
+ * 5 1-4 0 Reserved
+ * 1-4 1 Reserved
+ * 5-6 0 Port 2's Special LED
+ * 5-6 1 Port 6 Link (off=no link, on=link)
+ * 6 1-4 0 Duplex/Collision (off=half-duplex,on=full-duplex,blink=collision)
+ * 1-4 1 10/1000 Link/Act (off=no link, on=10 or 1000 link, blink=activity)
+ * 5-6 0 Port 5 Duplex/Collision (off=half-duplex, on=full-duplex, blink=col)
+ * 5-6 1 Port 6 Duplex/Collision (off=half-duplex, on=full-duplex, blink=col)
+ * 7 1-4 0 10/1000 Link/Act (off=no link, on=10 or 1000 link, blink=activity)
+ * 1-4 1 10/1000 Link (off=no link, on=10 or 1000 link)
+ * 5-6 0 Port 5 Link/Act/Speed by Blink rate (off=no link, on=link, blink=activity, blink speed=link speed)
+ * 5-6 1 Port 6 Link/Act/Speed by Blink rate (off=no link, on=link, blink=activity, blink speed=link speed)
+ * 8 1-4 0 Link (off=no link, on=link)
+ * 1-4 1 Activity (off=no link, blink on=activity)
+ * 5-6 0 Port 6 Link/Act (off=no link, on=link, blink=activity)
+ * 5-6 1 Port 0's Special LED
+ * 9 1-4 0 10 Link (off=no link, on=10 link)
+ * 1-4 1 100 Link (off=no link, on=100 link)
+ * 5-6 0 Reserved
+ * 5-6 1 Port 1's Special LED
+ * a 1-4 0 10 Link/Act (off=no link, on=10 link, blink=activity)
+ * 1-4 1 100 Link/Act (off=no link, on=100 link, blink=activity)
+ * 5-6 0 Reserved
+ * 5-6 1 Port 2's Special LED
+ * b 1-4 0 100/1000 Link (off=no link, on=100 or 1000 link)
+ * 1-4 1 10/100 Link (off=no link, on=100 link, blink=activity)
+ * 5-6 0 Reserved
+ * 5-6 1 Reserved
+ * c * * PTP Act (blink on=PTP activity)
+ * d * * Force Blink
+ * e * * Force Off
+ * f * * Force On
+ */
+/* Select LED0 output */
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL0 0x0
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL1 0x1
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL2 0x2
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL3 0x3
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL4 0x4
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL5 0x5
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL6 0x6
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL7 0x7
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL8 0x8
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SEL9 0x9
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SELA 0xa
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SELB 0xb
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SELC 0xc
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SELD 0xd
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SELE 0xe
+#define MV88E6XXX_PORT_LED_CONTROL_LED0_SELF 0xf
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL0 (0x0 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL1 (0x1 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL2 (0x2 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL3 (0x3 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL4 (0x4 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL5 (0x5 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL6 (0x6 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL7 (0x7 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL8 (0x8 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SEL9 (0x9 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SELA (0xa << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SELB (0xb << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SELC (0xc << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SELD (0xd << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SELE (0xe << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_LED1_SELF (0xf << 4)
+/* Stretch and Blink Rate Control (Index 0x06 of LED Control) */
+/* Pulse Stretch Selection for all LED's on this port */
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_NONE (0 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_21MS (1 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_42MS (2 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_84MS (3 << 4)
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_PULSE_STRETCH_168MS (4 << 4)
+/* Blink Rate Selection for all LEDs on this port */
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_21MS 0
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_42MS 1
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_84MS 2
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_168MS 3
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_336MS 4
+#define MV88E6XXX_PORT_LED_CONTROL_0x06_BLINK_RATE_672MS 5
+ /* Control for Special LED (Index 0x7 of LED Control on Port0) */
+#define MV88E6XXX_PORT_LED_CONTROL_0x07_P0_LAN_LINKACT_SHIFT 0 /* bits 6:0 LAN Link Activity LED */
+/* Control for Special LED (Index 0x7 of LED Control on Port 1) */
+#define MV88E6XXX_PORT_LED_CONTROL_0x07_P1_WAN_LINKACT_SHIFT 0 /* bits 6:0 WAN Link Activity LED */
+/* Control for Special LED (Index 0x7 of LED Control on Port 2) */
+#define MV88E6XXX_PORT_LED_CONTROL_0x07_P2_PTP_ACT 0 /* bits 6:0 PTP Activity */
+
/* Offset 0x18: IEEE Priority Mapping Table */
#define MV88E6390_PORT_IEEE_PRIO_MAP_TABLE 0x18
#define MV88E6390_PORT_IEEE_PRIO_MAP_TABLE_UPDATE 0x8000
@@ -457,6 +581,15 @@ int mv88e6393x_port_set_cmode(struct mv88e6xxx_chip *chip, int port,
phy_interface_t mode);
int mv88e6185_port_get_cmode(struct mv88e6xxx_chip *chip, int port, u8 *cmode);
int mv88e6352_port_get_cmode(struct mv88e6xxx_chip *chip, int port, u8 *cmode);
+#ifdef CONFIG_NET_DSA_MV88E6XXX_LEDS
+int mv88e6xxx_port_setup_leds(struct mv88e6xxx_chip *chip, int port);
+#else
+static inline int mv88e6xxx_port_setup_leds(struct mv88e6xxx_chip *chip,
+ int port)
+{
+ return 0;
+}
+#endif
int mv88e6xxx_port_drop_untagged(struct mv88e6xxx_chip *chip, int port,
bool drop_untagged);
int mv88e6xxx_port_set_map_da(struct mv88e6xxx_chip *chip, int port, bool map);
This adds control over the hardware LEDs in the Marvell MV88E6xxx DSA switch and enables it for MV88E6352. This fixes an imminent problem on the Inteno XG6846 which has a WAN LED that simply do not work with hardware defaults: driver amendment is necessary. The patch is modeled after Christian Marangis LED support code for the QCA8k DSA switch, I got help with the register definitions from Tim Harvey. After this patch it is possible to activate hardware link indication like this (or with a similar script): cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/ echo netdev > trigger echo 1 > link This makes the green link indicator come up on any link speed. It is also possible to be more elaborate, like this: cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/ echo netdev > trigger echo 1 > link_1000 cd /sys/class/leds/Marvell\ 88E6352:05:01:amber:wan/ echo netdev > trigger echo 1 > link_100 Making the green LED come on for a gigabit link and the amber LED come on for a 100 mbit link. Each port has 2 LED slots (the hardware may use just one or none) and the hardware triggers are specified in four bits per LED, and some of the hardware triggers are only available on the SFP (fiber) uplink. The restrictions are described in the port.h header file where the registers are described. For example, selector 1 set for LED 1 on port 5 or 6 will indicate Fiber 1000 (gigabit) and activity with a blinking LED, but ONLY for an SFP connection. If port 5/6 is used with something not SFP, this selector is a noop: something else need to be selected. After the previous series rewriting the MV88E6xxx DT bindings to use YAML a "leds" subnode is already valid for each port, in my scratch device tree it looks like this: leds { #address-cells = <1>; #size-cells = <0>; led@0 { reg = <0>; color = <LED_COLOR_ID_GREEN>; function = LED_FUNCTION_LAN; default-state = "off"; linux,default-trigger = "netdev"; }; led@1 { reg = <1>; color = <LED_COLOR_ID_AMBER>; function = LED_FUNCTION_LAN; default-state = "off"; }; }; This DT config is not yet configuring everything: when the netdev default trigger is assigned the hw acceleration callbacks are not called, and there is no way to set the netdev sub-trigger type (such as link_1000) from the device tree, such as if you want a gigabit link indicator. This has to be done from userspace at this point. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- The attempt to make LED support more generic didn't work out as expected, so proposing to merge the very particular for now. --- Changes in v3: - Rebased on v6.12-rc1 - Add a blurb about SFP-only LED hardware triggers to the commit message. - Silently skip if no ethernet ports are specified in the fwnode for the device. - Add mv88e6xxx_port_led_write() and read() helper functions. - With the read() callback we can user read-modify-write on the control register and avoid keeping a cache of the control register value in the port struct. - Rename the configuration table after MV88E6352 since this is the only switch family currently supported and drop a comment that the code will have to select a per-family configuration table to support more families. - Pass values instead of pointers to mv88e6xxx_led_set_blinking_period(). - Depromote some dev_info() to dev_dbg() - Return errors if invalid LEDs are found or if classdev LEDs fail to initialize. - Read out previous hardware trigger and try to locate the current rule in use. - Link to v2: https://lore.kernel.org/r/20240810-mv88e6xxx-leds-v2-1-7417d5336686@linaro.org Changes in v2: - Rebased onto v6.11-rc1 - Make sure to make the LED code mostly optional to compile in by a Kconfig option. - Link to v1: https://lore.kernel.org/r/20231123-mv88e6xxx-leds-v1-1-3c379b3d23fb@linaro.org --- drivers/net/dsa/mv88e6xxx/Kconfig | 10 + drivers/net/dsa/mv88e6xxx/Makefile | 1 + drivers/net/dsa/mv88e6xxx/chip.c | 35 +- drivers/net/dsa/mv88e6xxx/chip.h | 11 + drivers/net/dsa/mv88e6xxx/leds.c | 844 +++++++++++++++++++++++++++++++++++++ drivers/net/dsa/mv88e6xxx/port.c | 1 + drivers/net/dsa/mv88e6xxx/port.h | 133 ++++++ 7 files changed, 1033 insertions(+), 2 deletions(-) --- base-commit: 98f7e32f20d28ec452afb208f9cffc08448a2652 change-id: 20231123-mv88e6xxx-leds-b8b9b316ff98 Best regards,