@@ -15,7 +15,7 @@
#include <linux/delay.h>
#include <linux/regulator/consumer.h>
-/* Contol registers */
+/* Control registers */
#define DRV2665_STATUS 0x00
#define DRV2665_CTRL_1 0x01
#define DRV2665_CTRL_2 0x02
@@ -16,7 +16,7 @@
#include <linux/delay.h>
#include <linux/regulator/consumer.h>
-/* Contol registers */
+/* Control registers */
#define DRV2667_STATUS 0x00
#define DRV2667_CTRL_1 0x01
#define DRV2667_CTRL_2 0x02
@@ -23,7 +23,7 @@
*
* The value is in byte range, however, I only figured out
* how bits 0b10011001 work. Some other bits, probably,
- * are meaningfull too.
+ * are meaningful too.
*
* Possible states:
*
@@ -739,7 +739,7 @@ static int ims_pcu_switch_to_bootloader(struct ims_pcu *pcu)
{
int error;
- /* Execute jump to the bootoloader */
+ /* Execute jump to the bootloader */
error = ims_pcu_execute_command(pcu, JUMP_TO_BTLDR, NULL, 0);
if (error) {
dev_err(pcu->dev,
@@ -25,7 +25,7 @@
/* CONTROL REGISTER 1 BITS */
#define PC1_OFF 0x7F
#define PC1_ON (1 << 7)
-/* Data ready funtion enable bit: set during probe if using irq mode */
+/* Data ready function enable bit: set during probe if using irq mode */
#define DRDYE (1 << 5)
/* DATA CONTROL REGISTER BITS */
#define ODR12_5F 0
@@ -515,7 +515,7 @@ static const struct soc_device_data soc_device_INT33D3 = {
};
/*
- * Button info for Microsoft Surface 3 (non pro), this is indentical to
+ * Button info for Microsoft Surface 3 (non pro), this is identical to
* the PNP0C40 info except that the home button is active-high.
*
* The Surface 3 Pro also has a MSHW0028 ACPI device, but that uses a custom
@@ -271,7 +271,7 @@ static struct key_entry keymap_fs_amilo_pro_v8210[] __initdata = {
{ KE_BLUETOOTH, 0x30 }, /* Fn+F10 */
{ KE_KEY, 0x31, {KEY_MAIL} }, /* mail button */
{ KE_KEY, 0x36, {KEY_WWW} }, /* www button */
- { KE_WIFI, 0x78 }, /* satelite dish button */
+ { KE_WIFI, 0x78 }, /* satellite dish button */
{ KE_END, FE_WIFI_LED }
};
@@ -377,7 +377,7 @@ static int yealink_do_idle_tasks(struct yealink_dev *yld)
if (len > sizeof(yld->ctl_data->data))
len = sizeof(yld->ctl_data->data);
- /* Combine up to <len> consecutive LCD bytes in a singe request
+ /* Combine up to <len> consecutive LCD bytes in a single request
*/
yld->ctl_data->cmd = CMD_LCD;
yld->ctl_data->offset = cpu_to_be16(ix);
@@ -614,7 +614,7 @@ static ssize_t show_line3(struct device *dev, struct device_attribute *attr,
return show_line(dev, buf, LCD_LINE3_OFFSET, LCD_LINE4_OFFSET);
}
-/* Writing to /sys/../lineX will set the coresponding LCD line.
+/* Writing to /sys/../lineX will set the corresponding LCD line.
* - Excess characters are ignored.
* - If less characters are written than allowed, the remaining digits are
* unchanged.
Fixed some confusing typos that were currently identified witch codespell, the details are as follows: -in the code comments: drivers/input/misc/drv2665.c:18: Contol ==> Control drivers/input/misc/drv2667.c:19: Contol ==> Control drivers/input/misc/ideapad_slidebar.c:26: meaningfull ==> meaningful drivers/input/misc/ims-pcu.c:742: bootoloader ==> bootloader drivers/input/misc/kxtj9.c:28: funtion ==> function drivers/input/misc/soc_button_array.c:518: indentical ==> identical drivers/input/misc/wistron_btns.c:274: satelite ==> satellite drivers/input/misc/yealink.c:380: singe ==> single drivers/input/misc/yealink.c:617: coresponding ==> corresponding Signed-off-by: Shen Lichuan <shenlichuan@vivo.com> --- drivers/input/misc/drv2665.c | 2 +- drivers/input/misc/drv2667.c | 2 +- drivers/input/misc/ideapad_slidebar.c | 2 +- drivers/input/misc/ims-pcu.c | 2 +- drivers/input/misc/kxtj9.c | 2 +- drivers/input/misc/soc_button_array.c | 2 +- drivers/input/misc/wistron_btns.c | 2 +- drivers/input/misc/yealink.c | 4 ++-- 8 files changed, 9 insertions(+), 9 deletions(-)