@@ -17,7 +17,7 @@ merged to this clock. The component clocks shall be of one of the
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
[2] Documentation/devicetree/bindings/clock/ti/mux.txt
-[3] Documentation/devicetree/bindings/clock/ti/divider.txt
+[3] Documentation/devicetree/bindings/clock/ti/ti,divider-clock.yaml
[4] Documentation/devicetree/bindings/clock/ti/gate.txt
Required properties:
deleted file mode 100644
@@ -1,115 +0,0 @@
-Binding for TI divider clock
-
-This binding uses the common clock binding[1]. It assumes a
-register-mapped adjustable clock rate divider that does not gate and has
-only one input clock or parent. By default the value programmed into
-the register is one less than the actual divisor value. E.g:
-
-register value actual divisor value
-0 1
-1 2
-2 3
-
-This assumption may be modified by the following optional properties:
-
-ti,index-starts-at-one - valid divisor values start at 1, not the default
-of 0. E.g:
-register value actual divisor value
-1 1
-2 2
-3 3
-
-ti,index-power-of-two - valid divisor values are powers of two. E.g:
-register value actual divisor value
-0 1
-1 2
-2 4
-
-Additionally an array of valid dividers may be supplied like so:
-
- ti,dividers = <4>, <8>, <0>, <16>;
-
-Which will map the resulting values to a divisor table by their index:
-register value actual divisor value
-0 4
-1 8
-2 <invalid divisor, skipped>
-3 16
-
-Any zero value in this array means the corresponding bit-value is invalid
-and must not be used.
-
-The binding must also provide the register to control the divider and
-unless the divider array is provided, min and max dividers. Optionally
-the number of bits to shift that mask, if necessary. If the shift value
-is missing it is the same as supplying a zero shift.
-
-This binding can also optionally provide support to the hardware autoidle
-feature, see [2].
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/clock/ti/autoidle.txt
-
-Required properties:
-- compatible : shall be "ti,divider-clock" or "ti,composite-divider-clock".
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : link to phandle of parent clock
-- reg : offset for register controlling adjustable divider
-
-Optional properties:
-- clock-output-names : from common clock binding.
-- ti,dividers : array of integers defining divisors
-- ti,bit-shift : number of bits to shift the divider value, defaults to 0
-- ti,min-div : min divisor for dividing the input clock rate, only
- needed if the first divisor is offset from the default value (1)
-- ti,max-div : max divisor for dividing the input clock rate, only needed
- if ti,dividers is not defined.
-- ti,index-starts-at-one : valid divisor programming starts at 1, not zero,
- only valid if ti,dividers is not defined.
-- ti,index-power-of-two : valid divisor programming must be a power of two,
- only valid if ti,dividers is not defined.
-- ti,autoidle-shift : bit shift of the autoidle enable bit for the clock,
- see [2]
-- ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0,
- see [2]
-- ti,set-rate-parent : clk_set_rate is propagated to parent
-- ti,latch-bit : latch the divider value to HW, only needed if the register
- access requires this. As an example dra76x DPLL_GMAC H14 divider implements
- such behavior.
-
-Examples:
-dpll_usb_m2_ck: dpll_usb_m2_ck@4a008190 {
- #clock-cells = <0>;
- compatible = "ti,divider-clock";
- clocks = <&dpll_usb_ck>;
- ti,max-div = <127>;
- reg = <0x190>;
- ti,index-starts-at-one;
-};
-
-aess_fclk: aess_fclk@4a004528 {
- #clock-cells = <0>;
- compatible = "ti,divider-clock";
- clocks = <&abe_clk>;
- ti,bit-shift = <24>;
- reg = <0x528>;
- ti,max-div = <2>;
-};
-
-dpll_core_m3x2_div_ck: dpll_core_m3x2_div_ck {
- #clock-cells = <0>;
- compatible = "ti,composite-divider-clock";
- clocks = <&dpll_core_x2_ck>;
- ti,max-div = <31>;
- reg = <0x0134>;
- ti,index-starts-at-one;
-};
-
-ssi_ssr_div_fck_3430es2: ssi_ssr_div_fck_3430es2 {
- #clock-cells = <0>;
- compatible = "ti,composite-divider-clock";
- clocks = <&corex2_fck>;
- ti,bit-shift = <8>;
- reg = <0x0a40>;
- ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
-};
new file mode 100644
@@ -0,0 +1,193 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/ti/ti,divider-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments divider clock
+
+maintainers:
+ - Tero Kristo <kristo@kernel.org>
+
+description: |
+ This clock It assumes a register-mapped adjustable clock rate divider
+ that does not gate and has only one input clock or parent. By default the
+ value programmed into the register is one less than the actual divisor value.
+ E.g:
+
+ register value actual divisor value
+ 0 1
+ 1 2
+ 2 3
+
+ This assumption may be modified by the following optional properties:
+
+ ti,index-starts-at-one - valid divisor values start at 1, not the default
+ of 0. E.g:
+ register value actual divisor value
+ 1 1
+ 2 2
+ 3 3
+
+ ti,index-power-of-two - valid divisor values are powers of two. E.g:
+ register value actual divisor value
+ 0 1
+ 1 2
+ 2 4
+
+ Additionally an array of valid dividers may be supplied like so:
+
+ ti,dividers = <4>, <8>, <0>, <16>;
+
+ Which will map the resulting values to a divisor table by their index:
+ register value actual divisor value
+ 0 4
+ 1 8
+ 2 <invalid divisor, skipped>
+ 3 16
+
+ Any zero value in this array means the corresponding bit-value is invalid
+ and must not be used.
+
+ The binding must also provide the register to control the divider and
+ unless the divider array is provided, min and max dividers. Optionally
+ the number of bits to shift that mask, if necessary. If the shift value
+ is missing it is the same as supplying a zero shift.
+
+ This binding can also optionally provide support to the hardware autoidle
+ feature, see [1].
+
+ [1] Documentation/devicetree/bindings/clock/ti/autoidle.txt
+
+properties:
+ compatible:
+ enum:
+ - ti,divider-clock
+ - ti,composite-divider-clock
+
+ "#clock-cells":
+ const: 0
+
+ clocks:
+ maxItems: 1
+
+ clock-output-names:
+ maxItems: 1
+
+ reg:
+ maxItems: 1
+
+ ti,dividers:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description:
+ array of integers defining divisors
+
+ ti,bit-shift:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ number of bits to shift the divider value
+ maximum: 31
+ default: 0
+
+ ti,min-div:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ min divisor for dividing the input clock rate, only
+ needed if the first divisor is offset from the default value (1)
+ minimum: 1
+ default: 1
+
+
+ ti,max-div:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ max divisor for dividing the input clock rate, only needed
+ if ti,dividers is not defined.
+
+ ti,index-starts-at-one:
+ type: boolean
+ description:
+ valid divisor programming starts at 1, not zero,
+ only valid if ti,dividers is not defined
+
+ ti,index-power-of-two:
+ type: boolean
+ description:
+ valid divisor programming must be a power of two,
+ only valid if ti,dividers is not defined.
+
+ ti,autoidle-shift:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ bit shift of the autoidle enable bit for the clock,
+ see [1].
+ maximum: 31
+ default: 0
+
+ ti,invert-autoidle-bit:
+ type: boolean
+ description:
+ autoidle is enabled by setting the bit to 0,
+ see [1]
+
+ ti,set-rate-parent:
+ type: boolean
+ description:
+ clk_set_rate is propagated to parent |
+
+ ti,latch-bit:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ latch the divider value to HW, only needed if the register
+ compatible access requires this. As an example dra76x DPLL_GMAC
+ H14 divider implements such behavior.
+
+dependentSchemas:
+ ti,dividers:
+ properties:
+ ti,min-div: false
+ ti,max-div: false
+ ti,index-power-of-two: false
+ ti,index-starts-at-one: false
+
+required:
+ - compatible
+ - "#clock-cells"
+ - clocks
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ clock-controller@190 {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&dpll_usb_ck>;
+ ti,max-div = <127>;
+ reg = <0x190>;
+ ti,index-starts-at-one;
+ };
+
+ clock-controller@528 {
+ #clock-cells = <0>;
+ compatible = "ti,divider-clock";
+ clocks = <&abe_clk>;
+ ti,bit-shift = <24>;
+ reg = <0x528>;
+ ti,max-div = <2>;
+ };
+
+ clock-controller@a40 {
+ #clock-cells = <0>;
+ compatible = "ti,composite-divider-clock";
+ clocks = <&corex2_fck>;
+ ti,bit-shift = <8>;
+ reg = <0x0a40>;
+ ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+ };
+ };
Convert the OMAP divider clock device tree binding to json-schema. Specify the creator of the original binding as a maintainer. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> --- .../bindings/clock/ti/composite.txt | 2 +- .../devicetree/bindings/clock/ti/divider.txt | 115 ----------- .../bindings/clock/ti/ti,divider-clock.yaml | 193 ++++++++++++++++++ 3 files changed, 194 insertions(+), 116 deletions(-) delete mode 100644 Documentation/devicetree/bindings/clock/ti/divider.txt create mode 100644 Documentation/devicetree/bindings/clock/ti/ti,divider-clock.yaml