Message ID | 20241020220011.212395-5-justin@justinweiss.com (mailing list archive) |
---|---|
State | New |
Headers | show |
Series | Add i2c driver for Bosch BMI260 IMU | expand |
Justin Weiss <justin@justinweiss.com> writes: > Adds support for the Bosch BMI260 6-axis IMU to the Bosch BMI270 > driver. Setup and operation is nearly identical to the Bosch BMI270, > but has a different chip ID and requires different firmware. > > Firmware is requested and loaded from userspace. > > Signed-off-by: Justin Weiss <justin@justinweiss.com> > --- > drivers/iio/imu/bmi270/bmi270.h | 1 + > drivers/iio/imu/bmi270/bmi270_core.c | 28 +++++++++++++++++++++++++++- > drivers/iio/imu/bmi270/bmi270_i2c.c | 13 +++++++++++++ > drivers/iio/imu/bmi270/bmi270_spi.c | 8 ++++++++ > 4 files changed, 49 insertions(+), 1 deletion(-) > > diff --git a/drivers/iio/imu/bmi270/bmi270.h b/drivers/iio/imu/bmi270/bmi270.h > index 93e5f387607b..d8f6d7cf47fc 100644 > --- a/drivers/iio/imu/bmi270/bmi270.h > +++ b/drivers/iio/imu/bmi270/bmi270.h > @@ -20,6 +20,7 @@ struct bmi270_chip_info { > }; > > extern const struct regmap_config bmi270_regmap_config; > +extern const struct bmi270_chip_info bmi260_chip_info; > extern const struct bmi270_chip_info bmi270_chip_info; > > int bmi270_core_probe(struct device *dev, struct regmap *regmap, > diff --git a/drivers/iio/imu/bmi270/bmi270_core.c b/drivers/iio/imu/bmi270/bmi270_core.c > index 5f08d786fa21..24e45d6f0706 100644 > --- a/drivers/iio/imu/bmi270/bmi270_core.c > +++ b/drivers/iio/imu/bmi270/bmi270_core.c > @@ -11,6 +11,11 @@ > #include "bmi270.h" > > #define BMI270_CHIP_ID_REG 0x00 > + > +/* Used to prevent sending incompatible firmware to BMI160 devices */ > +#define BMI160_CHIP_ID_VAL 0xD1 > + > +#define BMI260_CHIP_ID_VAL 0x27 > #define BMI270_CHIP_ID_VAL 0x24 > #define BMI270_CHIP_ID_MSK GENMASK(7, 0) > > @@ -55,6 +60,7 @@ > #define BMI270_PWR_CTRL_ACCEL_EN_MSK BIT(2) > #define BMI270_PWR_CTRL_TEMP_EN_MSK BIT(3) > > +#define BMI260_INIT_DATA_FILE "bmi260-init-data.fw" > #define BMI270_INIT_DATA_FILE "bmi270-init-data.fw" > > enum bmi270_scan { > @@ -66,6 +72,13 @@ enum bmi270_scan { > BMI270_SCAN_GYRO_Z, > }; > > +const struct bmi270_chip_info bmi260_chip_info = { > + .name = "bmi260", > + .chip_id = BMI260_CHIP_ID_VAL, > + .fw_name = BMI260_INIT_DATA_FILE, > +}; > +EXPORT_SYMBOL_NS_GPL(bmi260_chip_info, IIO_BMI270); > + > const struct bmi270_chip_info bmi270_chip_info = { > .name = "bmi270", > .chip_id = BMI270_CHIP_ID_VAL, > @@ -157,8 +170,21 @@ static int bmi270_validate_chip_id(struct bmi270_data *bmi270_device) > if (ret) > return dev_err_probe(dev, ret, "Failed to read chip id"); > > + /* > + * Some manufacturers use "BMI0160" for both the BMI160 and > + * BMI260. If the device is actually a BMI160, the bmi160 > + * driver should handle it and this driver should not. > + */ > + if (chip_id == BMI160_CHIP_ID_VAL) > + return -ENODEV; > + > if (chip_id != bmi270_device->chip_info->chip_id) > - dev_info(dev, "Unknown chip id 0x%x", chip_id); > + dev_info(dev, "Unexpected chip id 0x%x", chip_id); > + > + if (chip_id == bmi260_chip_info.chip_id) > + bmi270_device->chip_info = &bmi260_chip_info; > + else if (chip_id == bmi270_chip_info.chip_id) > + bmi270_device->chip_info = &bmi270_chip_info; > > return 0; > } > diff --git a/drivers/iio/imu/bmi270/bmi270_i2c.c b/drivers/iio/imu/bmi270/bmi270_i2c.c > index 394f27996059..3d0d8f3e8b63 100644 > --- a/drivers/iio/imu/bmi270/bmi270_i2c.c > +++ b/drivers/iio/imu/bmi270/bmi270_i2c.c > @@ -32,11 +32,23 @@ static int bmi270_i2c_probe(struct i2c_client *client) > } > > static const struct i2c_device_id bmi270_i2c_id[] = { > + { "bmi260", (kernel_ulong_t)&bmi260_chip_info }, > { "bmi270", (kernel_ulong_t)&bmi270_chip_info }, > { } > }; > The ACPI IDs with device pointers are here: > +static const struct acpi_device_id bmi270_acpi_match[] = { > + /* OrangePi NEO */ > + { "BMI0260", (kernel_ulong_t)&bmi260_chip_info }, > + /* GPD Win Mini, Aya Neo AIR Pro, OXP Mini Pro, etc. */ > + { "BMI0160", (kernel_ulong_t)&bmi260_chip_info }, > + /* GPD Win Max 2 */ > + { "10EC5280", (kernel_ulong_t)&bmi260_chip_info }, > + { } > +}; I pulled DSDT device excerpts for the GPD Win Mini (which uses the BMI0160 ACPI ID, even though it has a bmi260) and the OrangePi NEO (which uses the BMI0260 ACPI ID). I couldn't find a shipping device with a bmi260 using the 10EC5280 ACPI ID. Some prototype devices with the bmi260 may have used them: https://lore.kernel.org/all/CAFqHKTm2WRNkcSoBEE=oNbfu_9d9RagQHLydmv6q1=snO_MXyA@mail.gmail.com/ I can remove that ID from this changeset for now. GPD Win Mini: Device (BMI2) { Name (_ADR, Zero) // _ADR: Address Name (_HID, "BMI0160") // _HID: Hardware ID Name (_CID, "BMI0160") // _CID: Compatible ID Name (_DDN, "Accelerometer") // _DDN: DOS Device Name Name (_UID, One) // _UID: Unique ID Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings { Name (RBUF, ResourceTemplate () { I2cSerialBusV2 (0x0068, ControllerInitiated, 0x00061A80, AddressingMode7Bit, "\\_SB.I2CB", 0x00, ResourceConsumer, , Exclusive, ) GpioInt (Edge, ActiveLow, Exclusive, PullDefault, 0x0000, "\\_SB.GPIO", 0x00, ResourceConsumer, , ) { // Pin list 0x008B } }) Return (RBUF) /* \_SB_.I2CB.BMI2._CRS.RBUF */ } OperationRegion (CMS2, SystemIO, 0x72, 0x02) Field (CMS2, ByteAcc, NoLock, Preserve) { IND2, 8, DAT2, 8 } IndexField (IND2, DAT2, ByteAcc, NoLock, Preserve) { Offset (0x74), BACS, 32 } Method (ROMS, 0, NotSerialized) { Name (RBUF, Package (0x03) { "0 1 0", "1 0 0", "0 0 1" }) Return (RBUF) /* \_SB_.I2CB.BMI2.ROMS.RBUF */ } Method (CALS, 1, NotSerialized) { Local0 = Arg0 If (((Local0 == Zero) || (Local0 == Ones))) { Return (Local0) } Else { BACS = Local0 } } Method (_STA, 0, NotSerialized) // _STA: Status { Return (0x0F) } } OrangePi NEO: Device (BMI2) { Name (_ADR, Zero) // _ADR: Address Name (_HID, "BMI0260") // _HID: Hardware ID Name (_CID, "BMI0260") // _CID: Compatible ID Name (_DDN, "Accelerometer") // _DDN: DOS Device Name Name (_UID, One) // _UID: Unique ID Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings { Name (RBUF, ResourceTemplate () { I2cSerialBusV2 (0x0068, ControllerInitiated, 0x00061A80, AddressingMode7Bit, "\\_SB.I2CB", 0x00, ResourceConsumer, , Exclusive, ) GpioInt (Edge, ActiveLow, Exclusive, PullDefault, 0x0000, "\\_SB.GPIO", 0x00, ResourceConsumer, , ) { // Pin list 0x008B } }) Return (RBUF) /* \_SB_.I2CB.BMI2._CRS.RBUF */ } OperationRegion (CMS2, SystemIO, 0x72, 0x02) Field (CMS2, ByteAcc, NoLock, Preserve) { IND2, 8, DAT2, 8 } IndexField (IND2, DAT2, ByteAcc, NoLock, Preserve) { Offset (0x74), BACS, 32 } Method (ROMS, 0, NotSerialized) { Name (RBUF, Package (0x03) { "0 1 0", "1 0 0", "0 0 1" }) Return (RBUF) /* \_SB_.I2CB.BMI2.ROMS.RBUF */ } Method (CALS, 1, NotSerialized) { Local0 = Arg0 If (((Local0 == Zero) || (Local0 == Ones))) { Return (Local0) } Else { BACS = Local0 } } Method (_STA, 0, NotSerialized) // _STA: Status { Return (0x0F) } } > + > static const struct of_device_id bmi270_of_match[] = { > + { .compatible = "bosch,bmi260", .data = &bmi260_chip_info }, > { .compatible = "bosch,bmi270", .data = &bmi270_chip_info }, > { } > }; > @@ -44,6 +56,7 @@ static const struct of_device_id bmi270_of_match[] = { > static struct i2c_driver bmi270_i2c_driver = { > .driver = { > .name = "bmi270_i2c", > + .acpi_match_table = bmi270_acpi_match, > .of_match_table = bmi270_of_match, > }, > .probe = bmi270_i2c_probe, > diff --git a/drivers/iio/imu/bmi270/bmi270_spi.c b/drivers/iio/imu/bmi270/bmi270_spi.c > index 7c2062c660d9..7f42ed74023b 100644 > --- a/drivers/iio/imu/bmi270/bmi270_spi.c > +++ b/drivers/iio/imu/bmi270/bmi270_spi.c > @@ -65,11 +65,18 @@ static int bmi270_spi_probe(struct spi_device *spi) > } > > static const struct spi_device_id bmi270_spi_id[] = { > + { "bmi260", (kernel_ulong_t)&bmi260_chip_info}, > { "bmi270", (kernel_ulong_t)&bmi270_chip_info }, > { } > }; > > +static const struct acpi_device_id bmi270_acpi_match[] = { > + { "BOSC0260", (kernel_ulong_t)&bmi260_chip_info }, > + { } > +}; > + I can't find any evidence of BOSC0260 being used, besides existing in the Windows driver. As suggested in an earlier review, I added it here to encourage people looking at this driver in the future to use the correct ACPI ID. Thanks, Justin > static const struct of_device_id bmi270_of_match[] = { > + { .compatible = "bosch,bmi260", .data = &bmi260_chip_info }, > { .compatible = "bosch,bmi270", .data = &bmi270_chip_info }, > { } > }; > @@ -77,6 +84,7 @@ static const struct of_device_id bmi270_of_match[] = { > static struct spi_driver bmi270_spi_driver = { > .driver = { > .name = "bmi270", > + .acpi_match_table = bmi270_acpi_match, > .of_match_table = bmi270_of_match, > }, > .probe = bmi270_spi_probe,
On Tue, Oct 22, 2024 at 08:50:43AM -0700, Justin Weiss wrote: > Justin Weiss <justin@justinweiss.com> writes: ... > The ACPI IDs with device pointers are here: > > > +static const struct acpi_device_id bmi270_acpi_match[] = { > > + /* OrangePi NEO */ > > + { "BMI0260", (kernel_ulong_t)&bmi260_chip_info }, > > + /* GPD Win Mini, Aya Neo AIR Pro, OXP Mini Pro, etc. */ > > + { "BMI0160", (kernel_ulong_t)&bmi260_chip_info }, > > + /* GPD Win Max 2 */ > > + { "10EC5280", (kernel_ulong_t)&bmi260_chip_info }, > > + { } Cool! But please, keep them alphabetically ordered by ID. Can we push OrangePI NED to go and fix ACPI IDs eventually? > > +}; > > I pulled DSDT device excerpts for the GPD Win Mini (which uses the > BMI0160 ACPI ID, even though it has a bmi260) and the OrangePi NEO > (which uses the BMI0260 ACPI ID). > > I couldn't find a shipping device with a bmi260 using the 10EC5280 ACPI > ID. Some prototype devices with the bmi260 may have used them: > https://lore.kernel.org/all/CAFqHKTm2WRNkcSoBEE=oNbfu_9d9RagQHLydmv6q1=snO_MXyA@mail.gmail.com/ > > I can remove that ID from this changeset for now. Yes, please do not add anything that has no evidence of existence in the wild or approved vendor allocated ID. > GPD Win Mini: Add short parts of these to the commit message, or better split these to two patches each of them adding a new ID to the table. See below what I do want to see there (no need to have everything), i.e. I removed unneeded lines: > Device (BMI2) > { > Name (_ADR, Zero) // _ADR: Address My gosh, can this be fixed (seems rhetorical)? The _ADR must NOT be present together with _HID. It's against the ACPI specifications. > Name (_HID, "BMI0160") // _HID: Hardware ID > Name (_CID, "BMI0160") // _CID: Compatible ID > Name (_DDN, "Accelerometer") // _DDN: DOS Device Name > Name (_UID, One) // _UID: Unique ID > Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings > { > Name (RBUF, ResourceTemplate () > { > I2cSerialBusV2 (0x0068, ControllerInitiated, 0x00061A80, > AddressingMode7Bit, "\\_SB.I2CB", > 0x00, ResourceConsumer, , Exclusive, > ) > GpioInt (Edge, ActiveLow, Exclusive, PullDefault, 0x0000, > "\\_SB.GPIO", 0x00, ResourceConsumer, , > ) > { // Pin list > 0x008B > } > }) > Return (RBUF) /* \_SB_.I2CB.BMI2._CRS.RBUF */ > } ... > } > > OrangePi NEO: Same comments for this device. ... > > +static const struct acpi_device_id bmi270_acpi_match[] = { > > + { "BOSC0260", (kernel_ulong_t)&bmi260_chip_info }, > > + { } > > +}; > > I can't find any evidence of BOSC0260 being used, besides existing in > the Windows driver. As suggested in an earlier review, I added it here > to encourage people looking at this driver in the future to use the > correct ACPI ID. Are you official representative of Bosch or do you have a proof by the vendor that they allocated this ID? Otherwise we may NOT allocate IDs on their behalf and has not to be added.
On Tue, 22 Oct 2024 19:54:03 +0300 Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote: > On Tue, Oct 22, 2024 at 08:50:43AM -0700, Justin Weiss wrote: > > Justin Weiss <justin@justinweiss.com> writes: > > ... > > > The ACPI IDs with device pointers are here: > > > > > +static const struct acpi_device_id bmi270_acpi_match[] = { > > > + /* OrangePi NEO */ > > > + { "BMI0260", (kernel_ulong_t)&bmi260_chip_info }, > > > + /* GPD Win Mini, Aya Neo AIR Pro, OXP Mini Pro, etc. */ > > > + { "BMI0160", (kernel_ulong_t)&bmi260_chip_info }, > > > + /* GPD Win Max 2 */ > > > + { "10EC5280", (kernel_ulong_t)&bmi260_chip_info }, > > > + { } > > Cool! But please, keep them alphabetically ordered by ID. > > Can we push OrangePI NED to go and fix ACPI IDs eventually? > > > > +}; > > > > I pulled DSDT device excerpts for the GPD Win Mini (which uses the > > BMI0160 ACPI ID, even though it has a bmi260) and the OrangePi NEO > > (which uses the BMI0260 ACPI ID). > > > > I couldn't find a shipping device with a bmi260 using the 10EC5280 ACPI > > ID. Some prototype devices with the bmi260 may have used them: > > https://lore.kernel.org/all/CAFqHKTm2WRNkcSoBEE=oNbfu_9d9RagQHLydmv6q1=snO_MXyA@mail.gmail.com/ > > > > I can remove that ID from this changeset for now. > > Yes, please do not add anything that has no evidence of existence in the wild > or approved vendor allocated ID. > > > GPD Win Mini: > > Add short parts of these to the commit message, or better split these to two > patches each of them adding a new ID to the table. > > See below what I do want to see there (no need to have everything), > i.e. I removed unneeded lines: > > > Device (BMI2) > > { > > Name (_ADR, Zero) // _ADR: Address > > My gosh, can this be fixed (seems rhetorical)? The _ADR must NOT be present > together with _HID. It's against the ACPI specifications. > > > Name (_HID, "BMI0160") // _HID: Hardware ID > > Name (_CID, "BMI0160") // _CID: Compatible ID > > Name (_DDN, "Accelerometer") // _DDN: DOS Device Name > > Name (_UID, One) // _UID: Unique ID > > Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings > > { > > Name (RBUF, ResourceTemplate () > > { > > I2cSerialBusV2 (0x0068, ControllerInitiated, 0x00061A80, > > AddressingMode7Bit, "\\_SB.I2CB", > > 0x00, ResourceConsumer, , Exclusive, > > ) > > GpioInt (Edge, ActiveLow, Exclusive, PullDefault, 0x0000, > > "\\_SB.GPIO", 0x00, ResourceConsumer, , > > ) > > { // Pin list > > 0x008B > > } > > }) > > Return (RBUF) /* \_SB_.I2CB.BMI2._CRS.RBUF */ > > } > ... > > } > > > > > OrangePi NEO: > > Same comments for this device. > > ... > > > > +static const struct acpi_device_id bmi270_acpi_match[] = { > > > + { "BOSC0260", (kernel_ulong_t)&bmi260_chip_info }, > > > + { } > > > +}; > > > > I can't find any evidence of BOSC0260 being used, besides existing in > > the Windows driver. As suggested in an earlier review, I added it here > > to encourage people looking at this driver in the future to use the > > correct ACPI ID. > > Are you official representative of Bosch or do you have a proof by the vendor > that they allocated this ID? Otherwise we may NOT allocate IDs on their behalf > and has not to be added. Fair point. The provenance of the driver is a little disconnected from Bosch: https://ayaneo-1305909189.cos.accelerate.myqcloud.com/ayaneo_com/download/2023/UMDF2.0_BMI260_V1.0.23_5ID_signed_20H1.zip Justin, if you have contacts at ayaneo, maybe they can confirm if the IDs come from Bosch. Or maybe we can find someone at Bosch? Jonathan >
diff --git a/drivers/iio/imu/bmi270/bmi270.h b/drivers/iio/imu/bmi270/bmi270.h index 93e5f387607b..d8f6d7cf47fc 100644 --- a/drivers/iio/imu/bmi270/bmi270.h +++ b/drivers/iio/imu/bmi270/bmi270.h @@ -20,6 +20,7 @@ struct bmi270_chip_info { }; extern const struct regmap_config bmi270_regmap_config; +extern const struct bmi270_chip_info bmi260_chip_info; extern const struct bmi270_chip_info bmi270_chip_info; int bmi270_core_probe(struct device *dev, struct regmap *regmap, diff --git a/drivers/iio/imu/bmi270/bmi270_core.c b/drivers/iio/imu/bmi270/bmi270_core.c index 5f08d786fa21..24e45d6f0706 100644 --- a/drivers/iio/imu/bmi270/bmi270_core.c +++ b/drivers/iio/imu/bmi270/bmi270_core.c @@ -11,6 +11,11 @@ #include "bmi270.h" #define BMI270_CHIP_ID_REG 0x00 + +/* Used to prevent sending incompatible firmware to BMI160 devices */ +#define BMI160_CHIP_ID_VAL 0xD1 + +#define BMI260_CHIP_ID_VAL 0x27 #define BMI270_CHIP_ID_VAL 0x24 #define BMI270_CHIP_ID_MSK GENMASK(7, 0) @@ -55,6 +60,7 @@ #define BMI270_PWR_CTRL_ACCEL_EN_MSK BIT(2) #define BMI270_PWR_CTRL_TEMP_EN_MSK BIT(3) +#define BMI260_INIT_DATA_FILE "bmi260-init-data.fw" #define BMI270_INIT_DATA_FILE "bmi270-init-data.fw" enum bmi270_scan { @@ -66,6 +72,13 @@ enum bmi270_scan { BMI270_SCAN_GYRO_Z, }; +const struct bmi270_chip_info bmi260_chip_info = { + .name = "bmi260", + .chip_id = BMI260_CHIP_ID_VAL, + .fw_name = BMI260_INIT_DATA_FILE, +}; +EXPORT_SYMBOL_NS_GPL(bmi260_chip_info, IIO_BMI270); + const struct bmi270_chip_info bmi270_chip_info = { .name = "bmi270", .chip_id = BMI270_CHIP_ID_VAL, @@ -157,8 +170,21 @@ static int bmi270_validate_chip_id(struct bmi270_data *bmi270_device) if (ret) return dev_err_probe(dev, ret, "Failed to read chip id"); + /* + * Some manufacturers use "BMI0160" for both the BMI160 and + * BMI260. If the device is actually a BMI160, the bmi160 + * driver should handle it and this driver should not. + */ + if (chip_id == BMI160_CHIP_ID_VAL) + return -ENODEV; + if (chip_id != bmi270_device->chip_info->chip_id) - dev_info(dev, "Unknown chip id 0x%x", chip_id); + dev_info(dev, "Unexpected chip id 0x%x", chip_id); + + if (chip_id == bmi260_chip_info.chip_id) + bmi270_device->chip_info = &bmi260_chip_info; + else if (chip_id == bmi270_chip_info.chip_id) + bmi270_device->chip_info = &bmi270_chip_info; return 0; } diff --git a/drivers/iio/imu/bmi270/bmi270_i2c.c b/drivers/iio/imu/bmi270/bmi270_i2c.c index 394f27996059..3d0d8f3e8b63 100644 --- a/drivers/iio/imu/bmi270/bmi270_i2c.c +++ b/drivers/iio/imu/bmi270/bmi270_i2c.c @@ -32,11 +32,23 @@ static int bmi270_i2c_probe(struct i2c_client *client) } static const struct i2c_device_id bmi270_i2c_id[] = { + { "bmi260", (kernel_ulong_t)&bmi260_chip_info }, { "bmi270", (kernel_ulong_t)&bmi270_chip_info }, { } }; +static const struct acpi_device_id bmi270_acpi_match[] = { + /* OrangePi NEO */ + { "BMI0260", (kernel_ulong_t)&bmi260_chip_info }, + /* GPD Win Mini, Aya Neo AIR Pro, OXP Mini Pro, etc. */ + { "BMI0160", (kernel_ulong_t)&bmi260_chip_info }, + /* GPD Win Max 2 */ + { "10EC5280", (kernel_ulong_t)&bmi260_chip_info }, + { } +}; + static const struct of_device_id bmi270_of_match[] = { + { .compatible = "bosch,bmi260", .data = &bmi260_chip_info }, { .compatible = "bosch,bmi270", .data = &bmi270_chip_info }, { } }; @@ -44,6 +56,7 @@ static const struct of_device_id bmi270_of_match[] = { static struct i2c_driver bmi270_i2c_driver = { .driver = { .name = "bmi270_i2c", + .acpi_match_table = bmi270_acpi_match, .of_match_table = bmi270_of_match, }, .probe = bmi270_i2c_probe, diff --git a/drivers/iio/imu/bmi270/bmi270_spi.c b/drivers/iio/imu/bmi270/bmi270_spi.c index 7c2062c660d9..7f42ed74023b 100644 --- a/drivers/iio/imu/bmi270/bmi270_spi.c +++ b/drivers/iio/imu/bmi270/bmi270_spi.c @@ -65,11 +65,18 @@ static int bmi270_spi_probe(struct spi_device *spi) } static const struct spi_device_id bmi270_spi_id[] = { + { "bmi260", (kernel_ulong_t)&bmi260_chip_info}, { "bmi270", (kernel_ulong_t)&bmi270_chip_info }, { } }; +static const struct acpi_device_id bmi270_acpi_match[] = { + { "BOSC0260", (kernel_ulong_t)&bmi260_chip_info }, + { } +}; + static const struct of_device_id bmi270_of_match[] = { + { .compatible = "bosch,bmi260", .data = &bmi260_chip_info }, { .compatible = "bosch,bmi270", .data = &bmi270_chip_info }, { } }; @@ -77,6 +84,7 @@ static const struct of_device_id bmi270_of_match[] = { static struct spi_driver bmi270_spi_driver = { .driver = { .name = "bmi270", + .acpi_match_table = bmi270_acpi_match, .of_match_table = bmi270_of_match, }, .probe = bmi270_spi_probe,
Adds support for the Bosch BMI260 6-axis IMU to the Bosch BMI270 driver. Setup and operation is nearly identical to the Bosch BMI270, but has a different chip ID and requires different firmware. Firmware is requested and loaded from userspace. Signed-off-by: Justin Weiss <justin@justinweiss.com> --- drivers/iio/imu/bmi270/bmi270.h | 1 + drivers/iio/imu/bmi270/bmi270_core.c | 28 +++++++++++++++++++++++++++- drivers/iio/imu/bmi270/bmi270_i2c.c | 13 +++++++++++++ drivers/iio/imu/bmi270/bmi270_spi.c | 8 ++++++++ 4 files changed, 49 insertions(+), 1 deletion(-)