Message ID | 20241025193727.765195-2-zaeem.mohamed@amd.com (mailing list archive) |
---|---|
State | New |
Headers | show |
Series | Fail dm_atomic_check if cursor overlay is required at MAX_SURFACES | expand |
On 25/10/2024 16:37, Zaeem Mohamed wrote: > [why] > Prevent index-out-of-bounds due to requiring cursor overlay when > plane_count is MAX_SURFACES. Hi Zaeem, Thanks for working on this fix. > > [how] > Bounds check on plane_count when requiring overlay cursor. I agree. Atomic check makes sense. 1) Since the native cursor mode was previously the unique mode avaliable, I wonder if the driver should fall to native cursor mode in favor of the overlay planes advertised. I.e. if driver says it supports two overlay planes and the userspace requested both, cursor overlay mode should not be available or should switch to native cursor mode, as before the introduction of cursor overlay mode. 2) Then my second question: can we increase the number of surfaces to 4 first to accommodate more than one active overlay plane with cursor overly mode enabled. If four is still possible, this increase can reduce the number of commit failure scenarios and mitigate current userspace issues first. After addressing current array-out-of-bounds, follow-up patches can do the proper changes and checks. 3) IMHO, the incoherence between MAX_SURFACE_NUM and MAX_SURFACE should be addressed before adding debugging points. For example, there are part of the DC code using MAX_SURFACE_NUM == MAX_PLANE == 6 to allocate dc_surface_update arrays, instead of using MAX_SURFACE value. You can find one of this case here: https://gitlab.freedesktop.org/agd5f/linux/-/blob/amd-staging-drm-next/drivers/gpu/drm/amd/display/dc/core/dc.c#L4507 It doesn't make sense to me and it can contribute to an incomplete solution. Also, please add the references of bugs reported in the amd tracker, so far: Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3693 Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3594 > Co-developed-by: Melissa Wen <mwen@igalia.com> I don't think I contributed enough to your code to get any credits. Thanks, but you can remove my co-dev-by :) Best Regards, Melissa > Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com> > --- > amdgpu_dm/amdgpu_dm.c | 16 +++++++++++++++- > 1 file changed, 15 insertions(+), 1 deletion(-) > > diff --git a/amdgpu_dm/amdgpu_dm.c b/amdgpu_dm/amdgpu_dm.c > index df83e7b42b..c2595efb74 100644 > --- a/amdgpu_dm/amdgpu_dm.c > +++ b/amdgpu_dm/amdgpu_dm.c > @@ -11676,6 +11676,12 @@ static int amdgpu_dm_atomic_check(struct drm_device *dev, > * need to be added for DC to not disable a plane by mistake > */ > if (dm_new_crtc_state->cursor_mode == DM_CURSOR_OVERLAY_MODE) { > + if(dc->current_state->stream_status->plane_count >= MAX_SURFACES){ > + drm_dbg_driver(crtc->dev, > + "Can't enable cursor plane with %d planes\n", MAX_SURFACES); > + ret = -EINVAL; > + goto fail; > + } > ret = drm_atomic_add_affected_planes(state, crtc); > if (ret) > goto fail; > @@ -11769,8 +11775,16 @@ static int amdgpu_dm_atomic_check(struct drm_device *dev, > > /* Overlay cusor not subject to native cursor restrictions */ > dm_new_crtc_state = to_dm_crtc_state(new_crtc_state); > - if (dm_new_crtc_state->cursor_mode == DM_CURSOR_OVERLAY_MODE) > + if (dm_new_crtc_state->cursor_mode == DM_CURSOR_OVERLAY_MODE){ > + if(dc->current_state->stream_status->plane_count > MAX_SURFACES){ > + drm_dbg_driver(crtc->dev, > + "Can't enable cursor plane with %d planes\n", MAX_SURFACES); > + ret = -EINVAL; > + goto fail; > + } > + > continue; > + } > > /* Check if rotation or scaling is enabled on DCN401 */ > if ((drm_plane_mask(crtc->cursor) & new_crtc_state->plane_mask) &&
diff --git a/amdgpu_dm/amdgpu_dm.c b/amdgpu_dm/amdgpu_dm.c index df83e7b42b..c2595efb74 100644 --- a/amdgpu_dm/amdgpu_dm.c +++ b/amdgpu_dm/amdgpu_dm.c @@ -11676,6 +11676,12 @@ static int amdgpu_dm_atomic_check(struct drm_device *dev, * need to be added for DC to not disable a plane by mistake */ if (dm_new_crtc_state->cursor_mode == DM_CURSOR_OVERLAY_MODE) { + if(dc->current_state->stream_status->plane_count >= MAX_SURFACES){ + drm_dbg_driver(crtc->dev, + "Can't enable cursor plane with %d planes\n", MAX_SURFACES); + ret = -EINVAL; + goto fail; + } ret = drm_atomic_add_affected_planes(state, crtc); if (ret) goto fail; @@ -11769,8 +11775,16 @@ static int amdgpu_dm_atomic_check(struct drm_device *dev, /* Overlay cusor not subject to native cursor restrictions */ dm_new_crtc_state = to_dm_crtc_state(new_crtc_state); - if (dm_new_crtc_state->cursor_mode == DM_CURSOR_OVERLAY_MODE) + if (dm_new_crtc_state->cursor_mode == DM_CURSOR_OVERLAY_MODE){ + if(dc->current_state->stream_status->plane_count > MAX_SURFACES){ + drm_dbg_driver(crtc->dev, + "Can't enable cursor plane with %d planes\n", MAX_SURFACES); + ret = -EINVAL; + goto fail; + } + continue; + } /* Check if rotation or scaling is enabled on DCN401 */ if ((drm_plane_mask(crtc->cursor) & new_crtc_state->plane_mask) &&
[why] Prevent index-out-of-bounds due to requiring cursor overlay when plane_count is MAX_SURFACES. [how] Bounds check on plane_count when requiring overlay cursor. Co-developed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com> --- amdgpu_dm/amdgpu_dm.c | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-)