| Message ID | 20241028082332.21672-3-hs@denx.de (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: dts: imx8mp: add support for the ABB SoM and carrier | expand |
On 28/10/2024 09:23, Heiko Schocher wrote: > Add support for the i.MX8MP based aristainetos3 boards from ABB. > > The board uses a ABB specific SoM from ADLink, based on NXP > i.MX8MP SoC. The SoM is used on 3 different carrier boards, > with small differences, which are all catched up in > devicetree overlays. The kernel image, the basic dtb > and all dtbos are collected in a fitimage. As bootloader > is used U-Boot which detects in his SPL stage the carrier > board by probing some i2c devices. When the correct > carrier is probed, the SPL applies all needed dtbos to > the dtb with which U-Boot gets loaded. Same principle > later before linux image boot, U-Boot applies the dtbos > needed for the carrier board before booting Linux. > > Signed-off-by: Heiko Schocher <hs@denx.de> > --- > checkpatch dropped the following warnings: > arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi:248: warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented -- check ./Documentation/devicetree/bindings/ > > ignored, as this compatible string is usedin other dts too, for example in > > arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi > > arch/arm64/boot/dts/freescale/Makefile | 5 + > .../imx8mp-aristainetos3-adpismarc.dtsi | 64 + > .../imx8mp-aristainetos3-adpismarc.dtso | 14 + > .../imx8mp-aristainetos3-helios-lvds.dtsi | 89 ++ > .../imx8mp-aristainetos3-helios-lvds.dtso | 13 + > .../imx8mp-aristainetos3-helios.dtsi | 103 ++ > .../imx8mp-aristainetos3-helios.dtso | 13 + > .../imx8mp-aristainetos3-proton2s.dtsi | 176 +++ > .../imx8mp-aristainetos3-proton2s.dtso | 13 + > .../imx8mp-aristainetos3a-som-v1.dts | 18 + > .../imx8mp-aristainetos3a-som-v1.dtsi | 1210 +++++++++++++++++ > 11 files changed, 1718 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi > > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile > index 9d3df8b218a2..7c3586509b8b 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -163,6 +163,11 @@ imx8mn-tqma8mqnl-mba8mx-usbotg-dtbs += imx8mn-tqma8mqnl-mba8mx.dtb imx8mn-tqma8m > dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-lvds-tm070jvhg33.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-usbotg.dtb > > +dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3a-som-v1.dtb \ > + imx8mp-aristainetos3-adpismarc.dtbo \ > + imx8mp-aristainetos3-proton2s.dtbo \ > + imx8mp-aristainetos3-helios.dtbo \ > + imx8mp-aristainetos3-helios-lvds.dtbo > dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi > new file mode 100644 > index 000000000000..cc0cddaa33ea > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi > @@ -0,0 +1,64 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> > + */ > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/irq.h> > + > +&ecspi1 { > + spidev0: spi@0 { > + reg = <0>; > + compatible = "rohm,dh2228fv"; Hm? I have some doubts, what device is here? > + spi-max-frequency = <500000>; > + }; > +}; > + > +&ecspi2 { > + spidev1: spi@0 { > + reg = <0>; > + compatible = "rohm,dh2228fv"; > + spi-max-frequency = <500000>; > + }; > +}; > + > +&i2c2 { > + /* SX1509(2) U1001@IPi SMARC Plus */ > + gpio8: i2c2_gpioext0@3e { Uh, no, please never send us downstream code. Please follow DTS coding style in all upstream submissions. Also: Node names should be generic. See also an explanation and list of examples (not exhaustive) in DT specification: https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation > + /* GPIO Expander 2 Mapping : > + * - 0: E_GPIO1_0 <=> IPi SMARC Plus CN101_PIN29: E_GPIO1_0 > + * - 1: E_GPIO1_1 <=> IPi SMARC Plus CN101_PIN31: E_GPIO1_1 > + * - 2: E_GPIO1_2 <=> IPi SMARC Plus CN101_PIN32: E_GPIO1_2 > + * - 3: E_GPIO1_3 <=> IPi SMARC Plus CN101_PIN33: E_GPIO1_3 > + * - 4: E_GPIO1_4 <=> IPi SMARC Plus CN101_PIN35: E_GPIO1_4 > + * - 5: E_GPIO1_5 <=> IPi SMARC Plus CN101_PIN36: E_GPIO1_5 > + * - 6: E_GPIO1_6 <=> IPi SMARC Plus CN101_PIN37: E_GPIO1_6 > + * - 7: E_GPIO1_7 <=> IPi SMARC Plus CN101_PIN38: E_GPIO1_7 > + * - 8: E_GPIO2_8 <=> IPi SMARC Plus CN101_PIN40: E_GPIO2_8 > + * - 9: TP1002 <=> IPi SMARC Plus TP1002 (won't use) > + * - 10: TP1003 <=> IPi SMARC Plus TP1003 (won't use) > + * - 11: TP1004 <=> IPi SMARC Plus TP1004 (won't use) > + * - 12: TP1005 <=> IPi SMARC Plus TP1005 (won't use) > + * - 13: TP1006 <=> IPi SMARC Plus TP1006 (won't use) > + * - 14: TP1007 <=> IPi SMARC Plus TP1007 (won't use) > + * - 15: TP1008 <=> IPi SMARC Plus TP1008 (won't use) > + * - 16: OSCIO <=> IPi SMARC Plus TP1001 (won't use) > + */ > + #gpio-cells = <2>; > + #interrupt-cells = <2>; > + compatible = "semtech,sx1509q"; > + reg = <0x3e>; > + > + semtech,probe-reset; > + gpio-controller; > + interrupt-controller; > + > + interrupt-parent = <&gpio6>; > + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; > + }; > + Drop > +}; > + > +&flexcan1 { > + status = "okay"; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso > new file mode 100644 > index 000000000000..5a9adccbf7cf > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso > @@ -0,0 +1,14 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> > + */ > +/dts-v1/; > +/plugin/; > + > +#include "imx8mp-aristainetos3-adpismarc.dtsi" > + > +&{/} { > + model = "Aristainetos3 ADLink PI SMARC carrier"; > + compatible = "abb,aristainetos3-adpismarc", "imx8mp-aristianetos3", > + "abb,aristianetos3-som", "fsl,imx8mp"; It does not look like you tested the DTS against bindings. Please run `make dtbs_check W=1` (see Documentation/devicetree/bindings/writing-schema.rst or https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/ for instructions). And why this is DTSO, I have no clue... > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi > new file mode 100644 > index 000000000000..55aabd6fc1f7 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi > @@ -0,0 +1,89 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> > + */ > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/pwm/pwm.h> > + > +&{/} { > + panel: panel { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_lcd0_vdd_en>; > + compatible = "lg,lb070wv8"; > + backlight = <&lvds_backlight>; > + enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&ldb_lvds_ch0>; > + }; > + }; > + }; > +}; > + > +&gpio3 { > + mipi_lvds_select { No, read coding style. > + gpio-hog; > + gpios = <23 GPIO_ACTIVE_HIGH>; > + output-low; > + line-name = "mipi_lvds_select"; > + }; > +}; > + > +&hdmi_blk_ctrl { > + status = "disabled"; > +}; > + > +&hdmi_pvi { > + status = "disabled"; > +}; > + > +&hdmi_tx { > + status = "disabled"; > +}; > + > +&hdmi_tx_phy { > + status = "disabled"; > +}; > + > +&irqsteer_hdmi { > + status = "disabled"; > +}; > + > +&ldb_lvds_ch0 { > + fsl,data-mapping = "jeida"; > + fsl,data-width = <24>; > + remote-endpoint = <&panel_in>; > +}; > + > +&lcdif1 { > + status = "disabled"; > +}; > + > +&lcdif2 { > + status = "okay"; > +}; > + > +&lcdif3 { > + status = "disabled"; > +}; > + > +&lvds_backlight { > + status = "okay"; > +}; > + > +&lvds_bridge { > + status = "okay"; > +}; > + > +&media_blk_ctrl { > + /* > + * The internal divider will always divide the output LVDS clock by 7 > + * so our display needs 33246000 Hz, so set VIDEO_PLL1 to > + * 33246000 * 7 = 232722000 Hz > + */ > + assigned-clock-rates = <500000000>, <200000000>, <0>, <0>, <232722000>; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso > new file mode 100644 > index 000000000000..06d1883b962a > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso > @@ -0,0 +1,13 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> > + */ > +/dts-v1/; > +/plugin/; > + > +#include "imx8mp-aristainetos3-helios-lvds.dtsi" > + > +&{/} { > + model = "Aristainetos3 helios LVDS carrier"; > + compatible = "abb,aristainetos3-helios-lvds", "abb,aristainetos3-helios", "abb,aristianetos3-som", "fsl,imx8mp"; Read not only DTS coding style, but also kernel coding style. Lines are supposed to be wrapped according to kernel coding style. > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi > new file mode 100644 > index 000000000000..b4b1cb3b0cb3 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi > @@ -0,0 +1,103 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> > + */ > + > +#include <dt-bindings/gpio/gpio.h> > + > +&{/} { > + helios_gpio_leds { Node names should be generic. See also an explanation and list of examples (not exhaustive) in DT specification: https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation > + compatible = "gpio-leds"; > + > + helios_blue { So this was absolutely never tested. It does not look like you tested the DTS against bindings. Please run `make dtbs_check W=1` (see Documentation/devicetree/bindings/writing-schema.rst or https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/ for instructions). > + label = "helios:blue"; Use function and color instead. I finished review here. Rest of the code does not look good, really. You have so many, really so many, trivial issues which tools point out, that using humans for such review is just waste of our time. Best regards, Krzysztof
Hello Krzysztof, On 28.10.24 11:24, Krzysztof Kozlowski wrote: > On 28/10/2024 09:23, Heiko Schocher wrote: >> Add support for the i.MX8MP based aristainetos3 boards from ABB. >> >> The board uses a ABB specific SoM from ADLink, based on NXP >> i.MX8MP SoC. The SoM is used on 3 different carrier boards, >> with small differences, which are all catched up in >> devicetree overlays. The kernel image, the basic dtb >> and all dtbos are collected in a fitimage. As bootloader >> is used U-Boot which detects in his SPL stage the carrier >> board by probing some i2c devices. When the correct >> carrier is probed, the SPL applies all needed dtbos to >> the dtb with which U-Boot gets loaded. Same principle >> later before linux image boot, U-Boot applies the dtbos >> needed for the carrier board before booting Linux. >> >> Signed-off-by: Heiko Schocher <hs@denx.de> >> --- >> checkpatch dropped the following warnings: >> arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi:248: warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented -- check ./Documentation/devicetree/bindings/ >> >> ignored, as this compatible string is usedin other dts too, for example in >> >> arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi >> >> arch/arm64/boot/dts/freescale/Makefile | 5 + >> .../imx8mp-aristainetos3-adpismarc.dtsi | 64 + >> .../imx8mp-aristainetos3-adpismarc.dtso | 14 + >> .../imx8mp-aristainetos3-helios-lvds.dtsi | 89 ++ >> .../imx8mp-aristainetos3-helios-lvds.dtso | 13 + >> .../imx8mp-aristainetos3-helios.dtsi | 103 ++ >> .../imx8mp-aristainetos3-helios.dtso | 13 + >> .../imx8mp-aristainetos3-proton2s.dtsi | 176 +++ >> .../imx8mp-aristainetos3-proton2s.dtso | 13 + >> .../imx8mp-aristainetos3a-som-v1.dts | 18 + >> .../imx8mp-aristainetos3a-som-v1.dtsi | 1210 +++++++++++++++++ >> 11 files changed, 1718 insertions(+) >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts >> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi >> >> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile >> index 9d3df8b218a2..7c3586509b8b 100644 >> --- a/arch/arm64/boot/dts/freescale/Makefile >> +++ b/arch/arm64/boot/dts/freescale/Makefile >> @@ -163,6 +163,11 @@ imx8mn-tqma8mqnl-mba8mx-usbotg-dtbs += imx8mn-tqma8mqnl-mba8mx.dtb imx8mn-tqma8m >> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-lvds-tm070jvhg33.dtb >> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-usbotg.dtb >> >> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3a-som-v1.dtb \ >> + imx8mp-aristainetos3-adpismarc.dtbo \ >> + imx8mp-aristainetos3-proton2s.dtbo \ >> + imx8mp-aristainetos3-helios.dtbo \ >> + imx8mp-aristainetos3-helios-lvds.dtbo >> dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb >> dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb >> dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb >> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >> new file mode 100644 >> index 000000000000..cc0cddaa33ea >> --- /dev/null >> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >> @@ -0,0 +1,64 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >> +/* >> + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> >> + */ >> + >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/interrupt-controller/irq.h> >> + >> +&ecspi1 { >> + spidev0: spi@0 { >> + reg = <0>; >> + compatible = "rohm,dh2228fv"; > > Hm? I have some doubts, what device is here? $ grep -lr dh2228fv drivers/ drivers/spi/spidev.c Customer uses an userspace implementation... > >> + spi-max-frequency = <500000>; >> + }; >> +}; >> + >> +&ecspi2 { >> + spidev1: spi@0 { >> + reg = <0>; >> + compatible = "rohm,dh2228fv"; >> + spi-max-frequency = <500000>; >> + }; >> +}; >> + >> +&i2c2 { >> + /* SX1509(2) U1001@IPi SMARC Plus */ >> + gpio8: i2c2_gpioext0@3e { > > Uh, no, please never send us downstream code. > > Please follow DTS coding style in all upstream submissions. driver is in here: $ grep -lr probe-reset drivers/pinctrl/ drivers/pinctrl/pinctrl-sx150x.c > Also: > Node names should be generic. See also an explanation and list of > examples (not exhaustive) in DT specification: > https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation Sorry for the nodenames... And yes, I remove the comments. >> + /* GPIO Expander 2 Mapping : >> + * - 0: E_GPIO1_0 <=> IPi SMARC Plus CN101_PIN29: E_GPIO1_0 >> + * - 1: E_GPIO1_1 <=> IPi SMARC Plus CN101_PIN31: E_GPIO1_1 >> + * - 2: E_GPIO1_2 <=> IPi SMARC Plus CN101_PIN32: E_GPIO1_2 >> + * - 3: E_GPIO1_3 <=> IPi SMARC Plus CN101_PIN33: E_GPIO1_3 >> + * - 4: E_GPIO1_4 <=> IPi SMARC Plus CN101_PIN35: E_GPIO1_4 >> + * - 5: E_GPIO1_5 <=> IPi SMARC Plus CN101_PIN36: E_GPIO1_5 >> + * - 6: E_GPIO1_6 <=> IPi SMARC Plus CN101_PIN37: E_GPIO1_6 >> + * - 7: E_GPIO1_7 <=> IPi SMARC Plus CN101_PIN38: E_GPIO1_7 >> + * - 8: E_GPIO2_8 <=> IPi SMARC Plus CN101_PIN40: E_GPIO2_8 >> + * - 9: TP1002 <=> IPi SMARC Plus TP1002 (won't use) >> + * - 10: TP1003 <=> IPi SMARC Plus TP1003 (won't use) >> + * - 11: TP1004 <=> IPi SMARC Plus TP1004 (won't use) >> + * - 12: TP1005 <=> IPi SMARC Plus TP1005 (won't use) >> + * - 13: TP1006 <=> IPi SMARC Plus TP1006 (won't use) >> + * - 14: TP1007 <=> IPi SMARC Plus TP1007 (won't use) >> + * - 15: TP1008 <=> IPi SMARC Plus TP1008 (won't use) >> + * - 16: OSCIO <=> IPi SMARC Plus TP1001 (won't use) >> + */ >> + #gpio-cells = <2>; >> + #interrupt-cells = <2>; >> + compatible = "semtech,sx1509q"; >> + reg = <0x3e>; >> + >> + semtech,probe-reset; >> + gpio-controller; >> + interrupt-controller; >> + >> + interrupt-parent = <&gpio6>; >> + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; >> + }; >> + > > Drop > >> +}; >> + >> +&flexcan1 { >> + status = "okay"; >> +}; >> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso >> new file mode 100644 >> index 000000000000..5a9adccbf7cf >> --- /dev/null >> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso >> @@ -0,0 +1,14 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >> +/* >> + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> >> + */ >> +/dts-v1/; >> +/plugin/; >> + >> +#include "imx8mp-aristainetos3-adpismarc.dtsi" >> + >> +&{/} { >> + model = "Aristainetos3 ADLink PI SMARC carrier"; >> + compatible = "abb,aristainetos3-adpismarc", "imx8mp-aristianetos3", >> + "abb,aristianetos3-som", "fsl,imx8mp"; > > It does not look like you tested the DTS against bindings. Please run > `make dtbs_check W=1` (see > Documentation/devicetree/bindings/writing-schema.rst or > https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/ > for instructions). Thanks for the hint! I have to fix my scripts... > And why this is DTSO, I have no clue... > >> +}; >> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi >> new file mode 100644 >> index 000000000000..55aabd6fc1f7 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi >> @@ -0,0 +1,89 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >> +/* >> + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> >> + */ >> + >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/input/input.h> >> +#include <dt-bindings/interrupt-controller/arm-gic.h> >> +#include <dt-bindings/pwm/pwm.h> >> + >> +&{/} { >> + panel: panel { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_lcd0_vdd_en>; >> + compatible = "lg,lb070wv8"; >> + backlight = <&lvds_backlight>; >> + enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; >> + >> + port { >> + panel_in: endpoint { >> + remote-endpoint = <&ldb_lvds_ch0>; >> + }; >> + }; >> + }; >> +}; >> + >> +&gpio3 { >> + mipi_lvds_select { > > No, read coding style. > > >> + gpio-hog; >> + gpios = <23 GPIO_ACTIVE_HIGH>; >> + output-low; >> + line-name = "mipi_lvds_select"; >> + }; >> +}; >> + >> +&hdmi_blk_ctrl { >> + status = "disabled"; >> +}; >> + >> +&hdmi_pvi { >> + status = "disabled"; >> +}; >> + >> +&hdmi_tx { >> + status = "disabled"; >> +}; >> + >> +&hdmi_tx_phy { >> + status = "disabled"; >> +}; >> + >> +&irqsteer_hdmi { >> + status = "disabled"; >> +}; >> + >> +&ldb_lvds_ch0 { >> + fsl,data-mapping = "jeida"; >> + fsl,data-width = <24>; >> + remote-endpoint = <&panel_in>; >> +}; >> + >> +&lcdif1 { >> + status = "disabled"; >> +}; >> + >> +&lcdif2 { >> + status = "okay"; >> +}; >> + >> +&lcdif3 { >> + status = "disabled"; >> +}; >> + >> +&lvds_backlight { >> + status = "okay"; >> +}; >> + >> +&lvds_bridge { >> + status = "okay"; >> +}; >> + >> +&media_blk_ctrl { >> + /* >> + * The internal divider will always divide the output LVDS clock by 7 >> + * so our display needs 33246000 Hz, so set VIDEO_PLL1 to >> + * 33246000 * 7 = 232722000 Hz >> + */ >> + assigned-clock-rates = <500000000>, <200000000>, <0>, <0>, <232722000>; >> +}; >> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso >> new file mode 100644 >> index 000000000000..06d1883b962a >> --- /dev/null >> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso >> @@ -0,0 +1,13 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >> +/* >> + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> >> + */ >> +/dts-v1/; >> +/plugin/; >> + >> +#include "imx8mp-aristainetos3-helios-lvds.dtsi" >> + >> +&{/} { >> + model = "Aristainetos3 helios LVDS carrier"; >> + compatible = "abb,aristainetos3-helios-lvds", "abb,aristainetos3-helios", "abb,aristianetos3-som", "fsl,imx8mp"; > > Read not only DTS coding style, but also kernel coding style. Lines are > supposed to be wrapped according to kernel coding style. Yes, indeed, I have to fix my scripts... >> +}; >> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi >> new file mode 100644 >> index 000000000000..b4b1cb3b0cb3 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi >> @@ -0,0 +1,103 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >> +/* >> + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> >> + */ >> + >> +#include <dt-bindings/gpio/gpio.h> >> + >> +&{/} { >> + helios_gpio_leds { > > Node names should be generic. See also an explanation and list of > examples (not exhaustive) in DT specification: > https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation > > >> + compatible = "gpio-leds"; >> + >> + helios_blue { > > So this was absolutely never tested. > > It does not look like you tested the DTS against bindings. Please run > `make dtbs_check W=1` (see > Documentation/devicetree/bindings/writing-schema.rst or > https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/ > for instructions). > >> + label = "helios:blue"; > > Use function and color instead. > > I finished review here. Rest of the code does not look good, really. You > have so many, really so many, trivial issues which tools point out, that > using humans for such review is just waste of our time. Sorry for that, will call the tools... bye, Heiko
On 28/10/2024 11:41, Heiko Schocher wrote: > Hello Krzysztof, > > On 28.10.24 11:24, Krzysztof Kozlowski wrote: >> On 28/10/2024 09:23, Heiko Schocher wrote: >>> Add support for the i.MX8MP based aristainetos3 boards from ABB. >>> >>> The board uses a ABB specific SoM from ADLink, based on NXP >>> i.MX8MP SoC. The SoM is used on 3 different carrier boards, >>> with small differences, which are all catched up in >>> devicetree overlays. The kernel image, the basic dtb >>> and all dtbos are collected in a fitimage. As bootloader >>> is used U-Boot which detects in his SPL stage the carrier >>> board by probing some i2c devices. When the correct >>> carrier is probed, the SPL applies all needed dtbos to >>> the dtb with which U-Boot gets loaded. Same principle >>> later before linux image boot, U-Boot applies the dtbos >>> needed for the carrier board before booting Linux. >>> >>> Signed-off-by: Heiko Schocher <hs@denx.de> >>> --- >>> checkpatch dropped the following warnings: >>> arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi:248: warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented -- check ./Documentation/devicetree/bindings/ >>> >>> ignored, as this compatible string is usedin other dts too, for example in >>> >>> arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi >>> >>> arch/arm64/boot/dts/freescale/Makefile | 5 + >>> .../imx8mp-aristainetos3-adpismarc.dtsi | 64 + >>> .../imx8mp-aristainetos3-adpismarc.dtso | 14 + >>> .../imx8mp-aristainetos3-helios-lvds.dtsi | 89 ++ >>> .../imx8mp-aristainetos3-helios-lvds.dtso | 13 + >>> .../imx8mp-aristainetos3-helios.dtsi | 103 ++ >>> .../imx8mp-aristainetos3-helios.dtso | 13 + >>> .../imx8mp-aristainetos3-proton2s.dtsi | 176 +++ >>> .../imx8mp-aristainetos3-proton2s.dtso | 13 + >>> .../imx8mp-aristainetos3a-som-v1.dts | 18 + >>> .../imx8mp-aristainetos3a-som-v1.dtsi | 1210 +++++++++++++++++ >>> 11 files changed, 1718 insertions(+) >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts >>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi >>> >>> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile >>> index 9d3df8b218a2..7c3586509b8b 100644 >>> --- a/arch/arm64/boot/dts/freescale/Makefile >>> +++ b/arch/arm64/boot/dts/freescale/Makefile >>> @@ -163,6 +163,11 @@ imx8mn-tqma8mqnl-mba8mx-usbotg-dtbs += imx8mn-tqma8mqnl-mba8mx.dtb imx8mn-tqma8m >>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-lvds-tm070jvhg33.dtb >>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-usbotg.dtb >>> >>> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3a-som-v1.dtb \ >>> + imx8mp-aristainetos3-adpismarc.dtbo \ >>> + imx8mp-aristainetos3-proton2s.dtbo \ >>> + imx8mp-aristainetos3-helios.dtbo \ >>> + imx8mp-aristainetos3-helios-lvds.dtbo >>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb >>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb >>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb >>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>> new file mode 100644 >>> index 000000000000..cc0cddaa33ea >>> --- /dev/null >>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>> @@ -0,0 +1,64 @@ >>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >>> +/* >>> + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> >>> + */ >>> + >>> +#include <dt-bindings/gpio/gpio.h> >>> +#include <dt-bindings/interrupt-controller/irq.h> >>> + >>> +&ecspi1 { >>> + spidev0: spi@0 { >>> + reg = <0>; >>> + compatible = "rohm,dh2228fv"; >> >> Hm? I have some doubts, what device is here? > > $ grep -lr dh2228fv drivers/ > drivers/spi/spidev.c > > Customer uses an userspace implementation... That's not the question. I asked what device is here. > >> >>> + spi-max-frequency = <500000>; >>> + }; >>> +}; >>> + >>> +&ecspi2 { >>> + spidev1: spi@0 { >>> + reg = <0>; >>> + compatible = "rohm,dh2228fv"; >>> + spi-max-frequency = <500000>; >>> + }; >>> +}; >>> + >>> +&i2c2 { >>> + /* SX1509(2) U1001@IPi SMARC Plus */ >>> + gpio8: i2c2_gpioext0@3e { >> >> Uh, no, please never send us downstream code. >> >> Please follow DTS coding style in all upstream submissions. > > driver is in here: > > $ grep -lr probe-reset drivers/pinctrl/ > drivers/pinctrl/pinctrl-sx150x.c This so not related... Your driver does not matter. You send us poor quality downstream code. ... > >> And why this is DTSO, I have no clue... Why is this a DTSO, not a DTS? Best regards, Krzysztof
Hello Krzysztof, On 28.10.24 11:49, Krzysztof Kozlowski wrote: > On 28/10/2024 11:41, Heiko Schocher wrote: >> Hello Krzysztof, >> >> On 28.10.24 11:24, Krzysztof Kozlowski wrote: >>> On 28/10/2024 09:23, Heiko Schocher wrote: >>>> Add support for the i.MX8MP based aristainetos3 boards from ABB. >>>> >>>> The board uses a ABB specific SoM from ADLink, based on NXP >>>> i.MX8MP SoC. The SoM is used on 3 different carrier boards, >>>> with small differences, which are all catched up in >>>> devicetree overlays. The kernel image, the basic dtb >>>> and all dtbos are collected in a fitimage. As bootloader >>>> is used U-Boot which detects in his SPL stage the carrier >>>> board by probing some i2c devices. When the correct >>>> carrier is probed, the SPL applies all needed dtbos to >>>> the dtb with which U-Boot gets loaded. Same principle >>>> later before linux image boot, U-Boot applies the dtbos >>>> needed for the carrier board before booting Linux. >>>> >>>> Signed-off-by: Heiko Schocher <hs@denx.de> >>>> --- >>>> checkpatch dropped the following warnings: >>>> arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi:248: warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented -- check ./Documentation/devicetree/bindings/ >>>> >>>> ignored, as this compatible string is usedin other dts too, for example in >>>> >>>> arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi >>>> >>>> arch/arm64/boot/dts/freescale/Makefile | 5 + >>>> .../imx8mp-aristainetos3-adpismarc.dtsi | 64 + >>>> .../imx8mp-aristainetos3-adpismarc.dtso | 14 + >>>> .../imx8mp-aristainetos3-helios-lvds.dtsi | 89 ++ >>>> .../imx8mp-aristainetos3-helios-lvds.dtso | 13 + >>>> .../imx8mp-aristainetos3-helios.dtsi | 103 ++ >>>> .../imx8mp-aristainetos3-helios.dtso | 13 + >>>> .../imx8mp-aristainetos3-proton2s.dtsi | 176 +++ >>>> .../imx8mp-aristainetos3-proton2s.dtso | 13 + >>>> .../imx8mp-aristainetos3a-som-v1.dts | 18 + >>>> .../imx8mp-aristainetos3a-som-v1.dtsi | 1210 +++++++++++++++++ >>>> 11 files changed, 1718 insertions(+) >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts >>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi >>>> >>>> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile >>>> index 9d3df8b218a2..7c3586509b8b 100644 >>>> --- a/arch/arm64/boot/dts/freescale/Makefile >>>> +++ b/arch/arm64/boot/dts/freescale/Makefile >>>> @@ -163,6 +163,11 @@ imx8mn-tqma8mqnl-mba8mx-usbotg-dtbs += imx8mn-tqma8mqnl-mba8mx.dtb imx8mn-tqma8m >>>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-lvds-tm070jvhg33.dtb >>>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-usbotg.dtb >>>> >>>> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3a-som-v1.dtb \ >>>> + imx8mp-aristainetos3-adpismarc.dtbo \ >>>> + imx8mp-aristainetos3-proton2s.dtbo \ >>>> + imx8mp-aristainetos3-helios.dtbo \ >>>> + imx8mp-aristainetos3-helios-lvds.dtbo >>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb >>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb >>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb >>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>>> new file mode 100644 >>>> index 000000000000..cc0cddaa33ea >>>> --- /dev/null >>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>>> @@ -0,0 +1,64 @@ >>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >>>> +/* >>>> + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> >>>> + */ >>>> + >>>> +#include <dt-bindings/gpio/gpio.h> >>>> +#include <dt-bindings/interrupt-controller/irq.h> >>>> + >>>> +&ecspi1 { >>>> + spidev0: spi@0 { >>>> + reg = <0>; >>>> + compatible = "rohm,dh2228fv"; >>> >>> Hm? I have some doubts, what device is here? >> >> $ grep -lr dh2228fv drivers/ >> drivers/spi/spidev.c >> >> Customer uses an userspace implementation... > > That's not the question. I asked what device is here. I do not know, as on carrier boards there are only connectors, to which a spi device can be attached. So may I need to use here a more generic entry? >> >>> >>>> + spi-max-frequency = <500000>; >>>> + }; >>>> +}; >>>> + >>>> +&ecspi2 { >>>> + spidev1: spi@0 { >>>> + reg = <0>; >>>> + compatible = "rohm,dh2228fv"; >>>> + spi-max-frequency = <500000>; >>>> + }; >>>> +}; >>>> + >>>> +&i2c2 { >>>> + /* SX1509(2) U1001@IPi SMARC Plus */ >>>> + gpio8: i2c2_gpioext0@3e { >>> >>> Uh, no, please never send us downstream code. >>> >>> Please follow DTS coding style in all upstream submissions. >> >> driver is in here: >> >> $ grep -lr probe-reset drivers/pinctrl/ >> drivers/pinctrl/pinctrl-sx150x.c > > This so not related... Your driver does not matter. You send us poor > quality downstream code. The driver is upstream... see: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/pinctrl/pinctrl-sx150x.c or may I misunderstood you here too? Poor is my dts, checks are running and I fix them. > ... > >> >>> And why this is DTSO, I have no clue... > > Why is this a DTSO, not a DTS? Hmm... the idea is, that the bootloader applies the dtbo on runtime, when it has detected the carrier board it runs on, I tried to explain in cover letter. And again... sorry... bye, Heiko
On 28/10/2024 12:21, Heiko Schocher wrote: > Hello Krzysztof, > > On 28.10.24 11:49, Krzysztof Kozlowski wrote: >> On 28/10/2024 11:41, Heiko Schocher wrote: >>> Hello Krzysztof, >>> >>> On 28.10.24 11:24, Krzysztof Kozlowski wrote: >>>> On 28/10/2024 09:23, Heiko Schocher wrote: >>>>> Add support for the i.MX8MP based aristainetos3 boards from ABB. >>>>> >>>>> The board uses a ABB specific SoM from ADLink, based on NXP >>>>> i.MX8MP SoC. The SoM is used on 3 different carrier boards, >>>>> with small differences, which are all catched up in >>>>> devicetree overlays. The kernel image, the basic dtb >>>>> and all dtbos are collected in a fitimage. As bootloader >>>>> is used U-Boot which detects in his SPL stage the carrier >>>>> board by probing some i2c devices. When the correct >>>>> carrier is probed, the SPL applies all needed dtbos to >>>>> the dtb with which U-Boot gets loaded. Same principle >>>>> later before linux image boot, U-Boot applies the dtbos >>>>> needed for the carrier board before booting Linux. >>>>> >>>>> Signed-off-by: Heiko Schocher <hs@denx.de> >>>>> --- >>>>> checkpatch dropped the following warnings: >>>>> arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi:248: warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented -- check ./Documentation/devicetree/bindings/ >>>>> >>>>> ignored, as this compatible string is usedin other dts too, for example in >>>>> >>>>> arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi >>>>> >>>>> arch/arm64/boot/dts/freescale/Makefile | 5 + >>>>> .../imx8mp-aristainetos3-adpismarc.dtsi | 64 + >>>>> .../imx8mp-aristainetos3-adpismarc.dtso | 14 + >>>>> .../imx8mp-aristainetos3-helios-lvds.dtsi | 89 ++ >>>>> .../imx8mp-aristainetos3-helios-lvds.dtso | 13 + >>>>> .../imx8mp-aristainetos3-helios.dtsi | 103 ++ >>>>> .../imx8mp-aristainetos3-helios.dtso | 13 + >>>>> .../imx8mp-aristainetos3-proton2s.dtsi | 176 +++ >>>>> .../imx8mp-aristainetos3-proton2s.dtso | 13 + >>>>> .../imx8mp-aristainetos3a-som-v1.dts | 18 + >>>>> .../imx8mp-aristainetos3a-som-v1.dtsi | 1210 +++++++++++++++++ >>>>> 11 files changed, 1718 insertions(+) >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts >>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi >>>>> >>>>> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile >>>>> index 9d3df8b218a2..7c3586509b8b 100644 >>>>> --- a/arch/arm64/boot/dts/freescale/Makefile >>>>> +++ b/arch/arm64/boot/dts/freescale/Makefile >>>>> @@ -163,6 +163,11 @@ imx8mn-tqma8mqnl-mba8mx-usbotg-dtbs += imx8mn-tqma8mqnl-mba8mx.dtb imx8mn-tqma8m >>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-lvds-tm070jvhg33.dtb >>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-usbotg.dtb >>>>> >>>>> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3a-som-v1.dtb \ >>>>> + imx8mp-aristainetos3-adpismarc.dtbo \ >>>>> + imx8mp-aristainetos3-proton2s.dtbo \ >>>>> + imx8mp-aristainetos3-helios.dtbo \ >>>>> + imx8mp-aristainetos3-helios-lvds.dtbo >>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb >>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb >>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb >>>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>>>> new file mode 100644 >>>>> index 000000000000..cc0cddaa33ea >>>>> --- /dev/null >>>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>>>> @@ -0,0 +1,64 @@ >>>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >>>>> +/* >>>>> + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> >>>>> + */ >>>>> + >>>>> +#include <dt-bindings/gpio/gpio.h> >>>>> +#include <dt-bindings/interrupt-controller/irq.h> >>>>> + >>>>> +&ecspi1 { >>>>> + spidev0: spi@0 { >>>>> + reg = <0>; >>>>> + compatible = "rohm,dh2228fv"; >>>> >>>> Hm? I have some doubts, what device is here? >>> >>> $ grep -lr dh2228fv drivers/ >>> drivers/spi/spidev.c >>> >>> Customer uses an userspace implementation... >> >> That's not the question. I asked what device is here. > > I do not know, as on carrier boards there are only connectors, > to which a spi device can be attached. So may I need to use here > a more generic entry? So this description is just not true. You have here nothing connected and this cannot be in the DTS. > >>> >>>> >>>>> + spi-max-frequency = <500000>; >>>>> + }; >>>>> +}; >>>>> + >>>>> +&ecspi2 { >>>>> + spidev1: spi@0 { >>>>> + reg = <0>; >>>>> + compatible = "rohm,dh2228fv"; >>>>> + spi-max-frequency = <500000>; >>>>> + }; >>>>> +}; >>>>> + >>>>> +&i2c2 { >>>>> + /* SX1509(2) U1001@IPi SMARC Plus */ >>>>> + gpio8: i2c2_gpioext0@3e { >>>> >>>> Uh, no, please never send us downstream code. >>>> >>>> Please follow DTS coding style in all upstream submissions. >>> >>> driver is in here: >>> >>> $ grep -lr probe-reset drivers/pinctrl/ >>> drivers/pinctrl/pinctrl-sx150x.c >> >> This so not related... Your driver does not matter. You send us poor >> quality downstream code. > > The driver is upstream... see: > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/pinctrl/pinctrl-sx150x.c > > or may I misunderstood you here too? > > Poor is my dts, checks are running and I fix them. My comment was that I see this as you sent DTS code which is taken straight from some downstream code. >>>> And why this is DTSO, I have no clue... >> >> Why is this a DTSO, not a DTS? > > Hmm... the idea is, that the bootloader applies the dtbo on runtime, > when it has detected the carrier board it runs on, I tried to explain > in cover letter. Then there is some mess here. First, SoM cannot be DTS, because it cannot be booted. Second, specific board/carrier is the DTS. Third, overlays bring some subset of features, not new board. Best regards, Krzysztof
Hello Krzysztof, On 28.10.24 13:44, Krzysztof Kozlowski wrote: > On 28/10/2024 12:21, Heiko Schocher wrote: >> Hello Krzysztof, >> >> On 28.10.24 11:49, Krzysztof Kozlowski wrote: >>> On 28/10/2024 11:41, Heiko Schocher wrote: >>>> Hello Krzysztof, >>>> >>>> On 28.10.24 11:24, Krzysztof Kozlowski wrote: >>>>> On 28/10/2024 09:23, Heiko Schocher wrote: >>>>>> Add support for the i.MX8MP based aristainetos3 boards from ABB. >>>>>> >>>>>> The board uses a ABB specific SoM from ADLink, based on NXP >>>>>> i.MX8MP SoC. The SoM is used on 3 different carrier boards, >>>>>> with small differences, which are all catched up in >>>>>> devicetree overlays. The kernel image, the basic dtb >>>>>> and all dtbos are collected in a fitimage. As bootloader >>>>>> is used U-Boot which detects in his SPL stage the carrier >>>>>> board by probing some i2c devices. When the correct >>>>>> carrier is probed, the SPL applies all needed dtbos to >>>>>> the dtb with which U-Boot gets loaded. Same principle >>>>>> later before linux image boot, U-Boot applies the dtbos >>>>>> needed for the carrier board before booting Linux. >>>>>> >>>>>> Signed-off-by: Heiko Schocher <hs@denx.de> >>>>>> --- >>>>>> checkpatch dropped the following warnings: >>>>>> arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi:248: warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented -- check ./Documentation/devicetree/bindings/ >>>>>> >>>>>> ignored, as this compatible string is usedin other dts too, for example in >>>>>> >>>>>> arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi >>>>>> >>>>>> arch/arm64/boot/dts/freescale/Makefile | 5 + >>>>>> .../imx8mp-aristainetos3-adpismarc.dtsi | 64 + >>>>>> .../imx8mp-aristainetos3-adpismarc.dtso | 14 + >>>>>> .../imx8mp-aristainetos3-helios-lvds.dtsi | 89 ++ >>>>>> .../imx8mp-aristainetos3-helios-lvds.dtso | 13 + >>>>>> .../imx8mp-aristainetos3-helios.dtsi | 103 ++ >>>>>> .../imx8mp-aristainetos3-helios.dtso | 13 + >>>>>> .../imx8mp-aristainetos3-proton2s.dtsi | 176 +++ >>>>>> .../imx8mp-aristainetos3-proton2s.dtso | 13 + >>>>>> .../imx8mp-aristainetos3a-som-v1.dts | 18 + >>>>>> .../imx8mp-aristainetos3a-som-v1.dtsi | 1210 +++++++++++++++++ >>>>>> 11 files changed, 1718 insertions(+) >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts >>>>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi >>>>>> >>>>>> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile >>>>>> index 9d3df8b218a2..7c3586509b8b 100644 >>>>>> --- a/arch/arm64/boot/dts/freescale/Makefile >>>>>> +++ b/arch/arm64/boot/dts/freescale/Makefile >>>>>> @@ -163,6 +163,11 @@ imx8mn-tqma8mqnl-mba8mx-usbotg-dtbs += imx8mn-tqma8mqnl-mba8mx.dtb imx8mn-tqma8m >>>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-lvds-tm070jvhg33.dtb >>>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-usbotg.dtb >>>>>> >>>>>> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3a-som-v1.dtb \ >>>>>> + imx8mp-aristainetos3-adpismarc.dtbo \ >>>>>> + imx8mp-aristainetos3-proton2s.dtbo \ >>>>>> + imx8mp-aristainetos3-helios.dtbo \ >>>>>> + imx8mp-aristainetos3-helios-lvds.dtbo >>>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb >>>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb >>>>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb >>>>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>>>>> new file mode 100644 >>>>>> index 000000000000..cc0cddaa33ea >>>>>> --- /dev/null >>>>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi >>>>>> @@ -0,0 +1,64 @@ >>>>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >>>>>> +/* >>>>>> + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> >>>>>> + */ >>>>>> + >>>>>> +#include <dt-bindings/gpio/gpio.h> >>>>>> +#include <dt-bindings/interrupt-controller/irq.h> >>>>>> + >>>>>> +&ecspi1 { >>>>>> + spidev0: spi@0 { >>>>>> + reg = <0>; >>>>>> + compatible = "rohm,dh2228fv"; >>>>> >>>>> Hm? I have some doubts, what device is here? >>>> >>>> $ grep -lr dh2228fv drivers/ >>>> drivers/spi/spidev.c >>>> >>>> Customer uses an userspace implementation... >>> >>> That's not the question. I asked what device is here. >> >> I do not know, as on carrier boards there are only connectors, >> to which a spi device can be attached. So may I need to use here >> a more generic entry? > > So this description is just not true. You have here nothing connected > and this cannot be in the DTS. Okay, I try to find out, what devices are connected else I remove them. >>>> >>>>> >>>>>> + spi-max-frequency = <500000>; >>>>>> + }; >>>>>> +}; >>>>>> + >>>>>> +&ecspi2 { >>>>>> + spidev1: spi@0 { >>>>>> + reg = <0>; >>>>>> + compatible = "rohm,dh2228fv"; >>>>>> + spi-max-frequency = <500000>; >>>>>> + }; >>>>>> +}; >>>>>> + >>>>>> +&i2c2 { >>>>>> + /* SX1509(2) U1001@IPi SMARC Plus */ >>>>>> + gpio8: i2c2_gpioext0@3e { >>>>> >>>>> Uh, no, please never send us downstream code. >>>>> >>>>> Please follow DTS coding style in all upstream submissions. >>>> >>>> driver is in here: >>>> >>>> $ grep -lr probe-reset drivers/pinctrl/ >>>> drivers/pinctrl/pinctrl-sx150x.c >>> >>> This so not related... Your driver does not matter. You send us poor >>> quality downstream code. >> >> The driver is upstream... see: >> >> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/pinctrl/pinctrl-sx150x.c >> >> or may I misunderstood you here too? >> >> Poor is my dts, checks are running and I fix them. > > My comment was that I see this as you sent DTS code which is taken > straight from some downstream code. Hmm.. I made this based on linux-stable 6.6 and yes, comments I have from adlink sources. Again sorry... I was too fast sending my patch after local rebase to v6.12 >>>>> And why this is DTSO, I have no clue... >>> >>> Why is this a DTSO, not a DTS? >> >> Hmm... the idea is, that the bootloader applies the dtbo on runtime, >> when it has detected the carrier board it runs on, I tried to explain >> in cover letter. > > Then there is some mess here. First, SoM cannot be DTS, because it > cannot be booted. Second, specific board/carrier is the DTS. Third, > overlays bring some subset of features, not new board. I see, and will rework! BTW: I now finished running make W=1 O=$BDIR dt_binding_check make W=1 O=$BDIR dtbs_check and there are tons of warnings .. yes, a lot come from my changes (because I wasn't aware of the checks and I made stuff based on linux 6.6 stable and simply just rebased my work with 6.12-rc5 so I have to apologize!) But not all warnings come from my files... I will check, fix, rework my patchset! Thanks for your comments and patience! bye, Heiko
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 9d3df8b218a2..7c3586509b8b 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -163,6 +163,11 @@ imx8mn-tqma8mqnl-mba8mx-usbotg-dtbs += imx8mn-tqma8mqnl-mba8mx.dtb imx8mn-tqma8m dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-lvds-tm070jvhg33.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-usbotg.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3a-som-v1.dtb \ + imx8mp-aristainetos3-adpismarc.dtbo \ + imx8mp-aristainetos3-proton2s.dtbo \ + imx8mp-aristainetos3-helios.dtbo \ + imx8mp-aristainetos3-helios-lvds.dtbo dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi new file mode 100644 index 000000000000..cc0cddaa33ea --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi @@ -0,0 +1,64 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +&ecspi1 { + spidev0: spi@0 { + reg = <0>; + compatible = "rohm,dh2228fv"; + spi-max-frequency = <500000>; + }; +}; + +&ecspi2 { + spidev1: spi@0 { + reg = <0>; + compatible = "rohm,dh2228fv"; + spi-max-frequency = <500000>; + }; +}; + +&i2c2 { + /* SX1509(2) U1001@IPi SMARC Plus */ + gpio8: i2c2_gpioext0@3e { + /* GPIO Expander 2 Mapping : + * - 0: E_GPIO1_0 <=> IPi SMARC Plus CN101_PIN29: E_GPIO1_0 + * - 1: E_GPIO1_1 <=> IPi SMARC Plus CN101_PIN31: E_GPIO1_1 + * - 2: E_GPIO1_2 <=> IPi SMARC Plus CN101_PIN32: E_GPIO1_2 + * - 3: E_GPIO1_3 <=> IPi SMARC Plus CN101_PIN33: E_GPIO1_3 + * - 4: E_GPIO1_4 <=> IPi SMARC Plus CN101_PIN35: E_GPIO1_4 + * - 5: E_GPIO1_5 <=> IPi SMARC Plus CN101_PIN36: E_GPIO1_5 + * - 6: E_GPIO1_6 <=> IPi SMARC Plus CN101_PIN37: E_GPIO1_6 + * - 7: E_GPIO1_7 <=> IPi SMARC Plus CN101_PIN38: E_GPIO1_7 + * - 8: E_GPIO2_8 <=> IPi SMARC Plus CN101_PIN40: E_GPIO2_8 + * - 9: TP1002 <=> IPi SMARC Plus TP1002 (won't use) + * - 10: TP1003 <=> IPi SMARC Plus TP1003 (won't use) + * - 11: TP1004 <=> IPi SMARC Plus TP1004 (won't use) + * - 12: TP1005 <=> IPi SMARC Plus TP1005 (won't use) + * - 13: TP1006 <=> IPi SMARC Plus TP1006 (won't use) + * - 14: TP1007 <=> IPi SMARC Plus TP1007 (won't use) + * - 15: TP1008 <=> IPi SMARC Plus TP1008 (won't use) + * - 16: OSCIO <=> IPi SMARC Plus TP1001 (won't use) + */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1509q"; + reg = <0x3e>; + + semtech,probe-reset; + gpio-controller; + interrupt-controller; + + interrupt-parent = <&gpio6>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + }; + +}; + +&flexcan1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso new file mode 100644 index 000000000000..5a9adccbf7cf --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso @@ -0,0 +1,14 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + */ +/dts-v1/; +/plugin/; + +#include "imx8mp-aristainetos3-adpismarc.dtsi" + +&{/} { + model = "Aristainetos3 ADLink PI SMARC carrier"; + compatible = "abb,aristainetos3-adpismarc", "imx8mp-aristianetos3", + "abb,aristianetos3-som", "fsl,imx8mp"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi new file mode 100644 index 000000000000..55aabd6fc1f7 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi @@ -0,0 +1,89 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pwm/pwm.h> + +&{/} { + panel: panel { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd0_vdd_en>; + compatible = "lg,lb070wv8"; + backlight = <&lvds_backlight>; + enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; + + port { + panel_in: endpoint { + remote-endpoint = <&ldb_lvds_ch0>; + }; + }; + }; +}; + +&gpio3 { + mipi_lvds_select { + gpio-hog; + gpios = <23 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "mipi_lvds_select"; + }; +}; + +&hdmi_blk_ctrl { + status = "disabled"; +}; + +&hdmi_pvi { + status = "disabled"; +}; + +&hdmi_tx { + status = "disabled"; +}; + +&hdmi_tx_phy { + status = "disabled"; +}; + +&irqsteer_hdmi { + status = "disabled"; +}; + +&ldb_lvds_ch0 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + remote-endpoint = <&panel_in>; +}; + +&lcdif1 { + status = "disabled"; +}; + +&lcdif2 { + status = "okay"; +}; + +&lcdif3 { + status = "disabled"; +}; + +&lvds_backlight { + status = "okay"; +}; + +&lvds_bridge { + status = "okay"; +}; + +&media_blk_ctrl { + /* + * The internal divider will always divide the output LVDS clock by 7 + * so our display needs 33246000 Hz, so set VIDEO_PLL1 to + * 33246000 * 7 = 232722000 Hz + */ + assigned-clock-rates = <500000000>, <200000000>, <0>, <0>, <232722000>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso new file mode 100644 index 000000000000..06d1883b962a --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + */ +/dts-v1/; +/plugin/; + +#include "imx8mp-aristainetos3-helios-lvds.dtsi" + +&{/} { + model = "Aristainetos3 helios LVDS carrier"; + compatible = "abb,aristainetos3-helios-lvds", "abb,aristainetos3-helios", "abb,aristianetos3-som", "fsl,imx8mp"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi new file mode 100644 index 000000000000..b4b1cb3b0cb3 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi @@ -0,0 +1,103 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + */ + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + helios_gpio_leds { + compatible = "gpio-leds"; + + helios_blue { + label = "helios:blue"; + gpios = <&helios_pca6416 15 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + helios_green { + label = "helios:green"; + gpios = <&helios_pca6416 14 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + helios_red { + label = "helios:red"; + gpios = <&helios_pca6416 12 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + helios_yellow { + label = "helios:yellow"; + gpios = <&helios_pca6416 13 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; +}; + +&dp83867_0 { + status = "disabled"; +}; + +&ecspi1 { + spidev1_0: spi@0 { + compatible = "rohm,dh2228fv"; + reg = <0>; + spi-max-frequency = <54000000>; + }; + + spidev1_1: spi@1 { + compatible = "rohm,dh2228fv"; + reg = <1>; + spi-max-frequency = <54000000>; + }; +}; + +&ecspi2 { + spidev2_0: spi@0 { + compatible = "rohm,dh2228fv"; + reg = <0>; + spi-max-frequency = <54000000>; + }; +}; + +&fec { + status = "disabled"; +}; + +&i2c1 { + eeprom@57 { + compatible = "atmel,24c64"; + reg = <0x57>; + }; +}; + +&i2c3 { + helios_pca6416: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "DIN0_CON", + "DIN1_CON", + "DIN2_CON", + "DIN3_CON", + "DIN4_CON", + "DIN5_CON", + "DIN6_CON", + "DIN7_CON", + "PM102_RES", + "COMx_RES", + "BPL_RES", + "PC_RES", + "LED_RED", + "LED_YELLOW", + "LED_GREEN", + "LED_BLUE"; + }; + + rtc@68 { + compatible = "st,m41t00"; + reg = <0x68>; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso new file mode 100644 index 000000000000..e4f6cefe0d7e --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + */ +/dts-v1/; +/plugin/; + +#include "imx8mp-aristainetos3-helios.dtsi" + +&{/} { + model = "Aristainetos3 helios carrier"; + compatible = "abb,aristainetos3-helios", "abb,aristianetos3-som", "fsl,imx8mp"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi new file mode 100644 index 000000000000..31f244981580 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi @@ -0,0 +1,176 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + */ + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_led>; + + leda0 { + label = "leda0"; + gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + leda1 { + label = "leda1"; + gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + watchdog { + /* MAX6371KA */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_watchdog_gpio>; + compatible = "linux,wdt-gpio"; + always-running; + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + hw_algo = "level"; + /* Reset triggers in 3..9 seconds */ + hw_margin_ms = <1500>; + status = "okay"; + }; +}; + +&dp83867_0 { + status = "disabled"; +}; + +&eqos { + max-speed = <100>; +}; + +&fec { + status = "disabled"; +}; + +&ecspi1{ + fsl,spi-num-chipselects = <1>; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + + spidev1_0: spi@0 { + compatible = "rohm,dh2228fv"; + reg = <0>; + spi-max-frequency = <54000000>; + }; + +}; + +&ecspi2 { + spidev2_0: spi@0 { + compatible = "rohm,dh2228fv"; + reg = <0>; + spi-max-frequency = <54000000>; + }; +}; + +&gpio1 { + gpio-line-names = + "", "", "", "", "", "", "", "power", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio6 { + gpio-line-names = + "relay0", "relay1", "relay2", + "heater", "fan", "spare", + "clear", "fault"; +}; + +&i2c2 { + tlc59108@40 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,tlc59108"; + reg = <0x40>; + + system_red@0 { + label = "system:red"; + reg = <0x0>; + }; + + system_green@1 { + label = "system:green"; + reg = <0x1>; + }; + + hydrogen_green@2 { + label = "hydrogen:green"; + reg = <0x2>; + }; + + hydrogen_red@3 { + label = "hydrogen:red"; + reg = <0x3>; + }; + + hydrogen_blue@4 { + label = "hydrogen:blue"; + reg = <0x4>; + }; + + moisture_red@5 { + label = "moisture:red"; + reg = <0x5>; + }; + + moisture_green@6 { + label = "moisture:green"; + reg = <0x6>; + }; + + moisture_blue@7 { + label = "moisture:blue"; + reg = <0x7>; + }; + }; + + rtc1: rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; +}; + +// SER3 +&uart1 { + pinctrl-0 = <&pinctrl_uart1>; +}; + +// SER0 +&uart2 { + pinctrl-0 = <&pinctrl_uart2>; +}; + +// SER1 +&uart3 { + pinctrl-0 = <&pinctrl_uart3>; +}; + +// SER2 +&uart4 { + linux,rs485-enabled-at-boot-time; + uart-has-rtscts; + rs485-rts-active-low; + rs485-rts-delay = <0 0>; + rts-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>; +}; + +&usdhc1 { + status = "disabled"; +}; + +&wdog1 { + status = "okay"; +}; + +&iomuxc { + pinctrl-0 = <&pinctrl_gpio_proton2s>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso new file mode 100644 index 000000000000..6956059553d7 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + */ +/dts-v1/; +/plugin/; + +#include "imx8mp-aristainetos3-proton2s.dtsi" + +&{/} { + model = "Aristainetos3 proton2s carrier"; + compatible = "abb,aristainetos3-proton2s", "abb,aristianetos3-som", "fsl,imx8mp"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts new file mode 100644 index 000000000000..b53a2f4eb0ff --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + * + * IMX8MP ADLINK raw SoM carrier variant + */ + +/dts-v1/; + +#include <dt-bindings/leds/common.h> +#include <dt-bindings/phy/phy-imx8-pcie.h> +#include "imx8mp-aristainetos3a-som-v1.dtsi" + +/ { + model = "Aristainetos3 raw SoM carrier"; + compatible = "abb,imx8mp-aristianetos3", "abb,imx8mp-aristianetos3-som", + "fsl,imx8mp"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi new file mode 100644 index 000000000000..903917bf0061 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi @@ -0,0 +1,1210 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2024 Heiko Schocher <hs@denx.de> + */ + +#include "imx8mp.dtsi" +#include <dt-bindings/net/ti-dp83867.h> + +/ { + model = "ADLINK LEC-iMX8MP-Q-N-4G-32G"; + compatible = "abb,imx8mp-aristianetos3-som", "fsl,imx8mp"; + + aliases { + mmc0 = &usdhc3; /* eMMC */ + mmc1 = &usdhc2; /* MicroSD */ + ethernet0 = &eqos; + ethernet1 = &fec; + }; + + chosen { + bootargs = "console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200"; + stdout-path = &uart2; + }; + + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + usb_c_0_hs_ep: endpoint { + remote-endpoint = <&dwc3_0_hs_ep>; + }; + }; + }; + }; + + fixed-regulators { + compatible = "simple-bus"; + device_type = "fixed-regulators"; + #address-cells = <1>; + #size-cells = <0>; + + dp83867_2v5: regulator-enet { + compatible = "regulator-fixed"; + regulator-name = "enet-2v5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio7 15 GPIO_ACTIVE_HIGH>; + regulator-boot-on; + regulator-always-on; + enable-active-high; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_led>; + + status { + label = "yellow:status"; + gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + lvds_backlight: lvds_backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lvds_pwr_en>; + pwms = <&pwm2 0 100000>; + enable-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + status = "disabled"; + + brightness-levels = < 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100>; + default-brightness-level = <80>; + }; + + memory@40000000 { + device_type = "memory"; + /* Memory size 512 MiB..8 GiB will be filled by U-Boot */ + reg = <0x0 0x40000000 0 0x08000000>; + }; + + pcie0_refclk: pcie0-refclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + }; + + reg_can1_stby: regulator-can1-stby { + compatible = "regulator-fixed"; + regulator-name = "can1-stby"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1_reg>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_can2_stby: regulator-can2-stby { + compatible = "regulator-fixed"; + regulator-name = "can2-stby"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2_reg>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb1_host_vbus: regulator-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1_host_vbus"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1_vbus>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_usdhc2_vmmc: regulator-usdhc2-vmmc { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio2 19 0>; /* SD2_RESET */ + off-on-delay-us = <12000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2_vmmc>; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "VDD_3V3_SD"; + startup-delay-us = <100>; + vin-supply = <&buck4>; + }; + + reg_vdd_3p3v_awo: regulator-vdd-3p3v-awo { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "VDD_3P3V_AWO"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + rpmsg_reserved: rpmsg@55800000 { + no-map; + reg = <0 0x55800000 0 0x800000>; + }; + }; +}; + +&A53_0 { + cpu-supply = <&buck2>; +}; + +&A53_1 { + cpu-supply = <&buck2>; +}; + +&A53_2 { + cpu-supply = <&buck2>; +}; + +&A53_3 { + cpu-supply = <&buck2>; +}; + +&clk { + init-on-array = <IMX8MP_CLK_HSIO_ROOT>; + clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>, <&clk_ext2>, + <&clk_ext3>, <&clk_ext4>; + clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2", + "clk_ext3", "clk_ext4"; + assigned-clocks = <&clk IMX8MP_CLK_A53_SRC>, + <&clk IMX8MP_CLK_A53_CORE>, + <&clk IMX8MP_CLK_NOC>, + <&clk IMX8MP_CLK_NOC_IO>, + <&clk IMX8MP_CLK_GIC>, + <&clk IMX8MP_CLK_AUDIO_AHB>, + <&clk IMX8MP_CLK_AUDIO_AXI_SRC>, + <&clk IMX8MP_AUDIO_PLL1>, + <&clk IMX8MP_AUDIO_PLL2>, + <&clk IMX8MP_VIDEO_PLL1>; +}; + +&ecspi1{ + #address-cells = <1>; + #size-cells = <0>; + + fsl,spi-num-chipselects = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs2>; + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW &gpio1 6 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&ecspi2 { + #address-cells = <1>; + #size-cells = <0>; + fsl,spi-num-chipselects = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +/* eth0 */ +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos_rgmii>; + phy-handle = <&dp83867_1>; + phy-mode = "rgmii-id"; + snps,force_thresh_dma_mode; + snps,mtl-tx-config = <&mtl_tx_setup>; + snps,mtl-rx-config = <&mtl_rx_setup>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + dp83867_1: eqos-ethernet-phy@0 { + compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22"; + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_1_75_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_75_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,min-output-impedance; + ti,dp83867-rxctrl-strap-quirk; + interrupt-parent = <&gpio4>; + interrupts = <21 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <5>; + snps,tx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,priority = <0x1>; + }; + queue1 { + snps,dcb-algorithm; + snps,priority = <0x2>; + }; + queue2 { + snps,dcb-algorithm; + snps,priority = <0x4>; + }; + queue3 { + snps,dcb-algorithm; + snps,priority = <0x8>; + }; + queue4 { + snps,dcb-algorithm; + snps,priority = <0xf0>; + }; + }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <5>; + snps,rx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,priority = <0x1>; + snps,map-to-dma-channel = <0>; + }; + queue1 { + snps,dcb-algorithm; + snps,priority = <0x2>; + snps,map-to-dma-channel = <1>; + }; + queue2 { + snps,dcb-algorithm; + snps,priority = <0x4>; + snps,map-to-dma-channel = <2>; + }; + queue3 { + snps,dcb-algorithm; + snps,priority = <0x8>; + snps,map-to-dma-channel = <3>; + }; + queue4 { + snps,dcb-algorithm; + snps,priority = <0xf0>; + snps,map-to-dma-channel = <4>; + }; + }; + +}; + +/* eth1 */ +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec_rgmii>; + phy-handle = <&dp83867_0>; + phy-mode = "rgmii-id"; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + dp83867_0: ethernet-phy@1 { + compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22"; + reg = <1>; + interrupt-parent = <&gpio4>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + reset-gpio = <&gpio4 2 GPIO_ACTIVE_LOW>; + + ti,rx-internal-delay = <DP83867_RGMIIDCTL_1_75_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_75_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + + ti,min-output-impedance; + ti,dp83867-rxctrl-strap-quirk; + eee-broken-1000t; + }; + }; +}; + +&flexcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_can1_stby>; + status = "disabled"; +}; + +&flexcan2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + xceiver-supply = <®_can1_stby>; + status = "disabled"; +}; + +&hdmi_blk_ctrl { + status = "okay"; +}; + +&hdmi_pvi { + status = "okay"; +}; + +&hdmi_tx { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hdmi>; + status = "okay"; +}; + +&hdmi_tx_phy { + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio5 14 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio5 15 GPIO_ACTIVE_HIGH>; + status = "okay"; + + pmic: pmic@25 { + compatible = "nxp,pca9450c"; + reg = <0x25>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + /* + * i.MX 8M Plus Data Sheet for Consumer Products + * 3.1.4 Operating ranges + * MIMX8ML8CVNKZAB + */ + regulators { + buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ + regulator-compatible = "BUCK1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-ramp-delay = <3125>; + regulator-always-on; + regulator-boot-on; + }; + + buck2: BUCK2 { /* VDD_ARM */ + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; + regulator-compatible = "BUCK2"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-ramp-delay = <3125>; + regulator-always-on; + regulator-boot-on; + }; + + buck4: BUCK4 { /* VDD_3V3 */ + regulator-compatible = "BUCK4"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck5: BUCK5 { /* VDD_1V8 */ + regulator-compatible = "BUCK5"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-always-on; + regulator-boot-on; + }; + + buck6: BUCK6 { /* NVCC_DRAM_1V1 */ + regulator-compatible = "BUCK6"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1: LDO1 { /* NVCC_SNVS_1V8 */ + regulator-compatible = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo2: LDO2 { /* VDDA_1V8 */ + regulator-compatible = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo3: LDO3 { /* VDDA_1V8 */ + regulator-compatible = "LDO3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo4: LDO4 { /* PMIC_LDO4 */ + regulator-compatible = "LDO4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo5: LDO5 { /* NVCC_SD2 */ + regulator-compatible = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c2>; + pinctrl-1 = <&pinctrl_i2c2_gpio>; + scl-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c3>; + pinctrl-1 = <&pinctrl_i2c3_gpio>; + scl-gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio5 19 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&i2c5 { + #address-cells = <1>; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c5>; + status = "okay"; +}; + +&i2c6 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c6>; + pinctrl-1 = <&pinctrl_i2c6_gpio>; + scl-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>; + status = "okay"; + + /* TPM - ST33TPHF2XI2C U2301 */ + tpm: tpm@2e { + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "st,st33ktpm2xi2c"; + reg = <0x2e>; + + label = "tpm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c6_tpm_irq &pinctrl_tpm>; + interrupt-parent = <&gpio3>; + interrupts = <14 IRQ_TYPE_LEVEL_LOW>; + reset-gpio = <&gpio6 11 GPIO_ACTIVE_LOW>; + status = "okay"; + }; + + /* SX1509(0) U2605 */ + gpio6: i2c6_gpioext0@3f { + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1509q"; + reg = <0x3f>; + + semtech,probe-reset; + gpio-controller; + interrupt-controller; + + interrupt-parent = <&gpio1>; + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; + }; + + /* SX1509(1) U2606 */ + gpio7: i2c6_gpioext1@70 { + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1509q"; + reg = <0x70>; + + semtech,probe-reset; + gpio-controller; + interrupt-controller; + + interrupt-parent = <&gpio4>; + interrupts = <19 IRQ_TYPE_EDGE_FALLING>; + + pinctrl_tpm: aristainetos3-tpm-grp { + pins = "gpio6","gpio7"; // TPM_PP, TPM_LP + output-high; + }; + }; + + /* RTC U2607 */ + rtc0: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + #clock-cells = <0>; + }; +}; + +&irqsteer_hdmi { + status = "okay"; +}; + +&lcdif1 { + status = "disabled"; +}; + +&lcdif2 { + status = "disabled"; +}; + +/* HDMI */ +&lcdif3 { + status = "okay"; + +}; + +&lvds_bridge { + status = "disabled"; +}; + +&mipi_dsi { + status = "disabled"; +}; + +&pcie{ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie>; + reset-gpio = <&gpio4 20 GPIO_ACTIVE_LOW>; + ext_osc = <0>; + clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, + <&clk IMX8MP_CLK_PCIE_AUX>, + <&clk IMX8MP_CLK_HSIO_AXI>, + <&clk IMX8MP_CLK_PCIE_ROOT>; + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>, + <&clk IMX8MP_CLK_PCIE_AUX>; + assigned-clock-rates = <500000000>, <10000000>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>, + <&clk IMX8MP_SYS_PLL2_50M>; + reserved-region = <&rpmsg_reserved>; + fsl,tx-deemph-gen1 = <0x1f>; + fsl,max-link-speed = <3>; + status = "okay"; +}; + +&pcie_phy{ + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>; + clocks = <&pcie0_refclk>; + clock-names = "ref"; + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm2 { + #pwm-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; + status = "okay"; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usb3_phy0 { + fsl,phy-tx-vref-tune = <0xe>; + fsl,phy-tx-preemp-amp-tune = <3>; + fsl,phy-tx-vboost-level = <5>; + fsl,phy-comp-dis-tune = <7>; + fsl,pcs-tx-deemph-3p5db = <0x21>; + fsl,phy-pcs-tx-swing-full = <0x7f>; + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb_dwc3_0 { + dr_mode = "otg"; + hnp-disable; + srp-disable; + adp-disable; + usb-role-switch; + role-switch-default-mode = "peripheral"; + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + dwc3_0_hs_ep: endpoint@0 { + reg = <0>; + remote-endpoint = <&usb_c_0_hs_ep>; + }; + }; +}; + +&usb3_phy1 { + fsl,phy-tx-preemp-amp-tune = <3>; + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&usb_dwc3_1 { + dr_mode = "host"; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +/* SD slot */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_usdhc2_vmmc>; + bus-width = <4>; + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + vmmc-supply = <&buck4>; + vqmmc-supply = <&buck5>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + + pinctrl_disp_select: aristainetos3-dispselect-grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_RXD2__GPIO3_IO23 0xd6 + >; + }; + + pinctrl_ecspi1: aristainetos3-ecspi1-grp { + fsl,pins = < + MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK 0x82 + MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI 0x82 + MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO 0x82 + MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09 0x40000 + >; + }; + + pinctrl_ecspi1_cs2: aristainetos3-ecspi1-cs2-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06 0x40000 + >; + }; + + pinctrl_ecspi2: aristainetos3-ecspi2-grp { + fsl,pins = < + MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK 0x82 + MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI 0x82 + MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO 0x82 + MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13 0x40000 + >; + }; + + pinctrl_eqos_rgmii: aristainetos3-eqos-rgmii-grp { + fsl,pins = < + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3 + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3 + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91 + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91 + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91 + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91 + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91 + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f + MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22 0x19 + >; + }; + + pinctrl_fec_rgmii: aristainetos3-fec-rgmii-grp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3 + MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3 + MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91 + MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91 + MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91 + MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91 + MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91 + MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f + MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f + MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f + MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f + MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f + MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02 0x19 + >; + }; + + pinctrl_flexcan1: aristainetos3-flexcan1-grp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_RX__CAN1_RX 0x154 + MX8MP_IOMUXC_SPDIF_TX__CAN1_TX 0x154 + >; + }; + + pinctrl_flexcan2: aristainetos3-flexcan2-grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX 0x154 + MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX 0x154 + >; + }; + + pinctrl_flexcan1_reg: aristainetos3-flexcan1-reg-grp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05 0x154 /* CAN1_STBY */ + >; + }; + + pinctrl_flexcan2_reg: aristainetos3-flexcan2-reg-grp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27 0x154 /* CAN2_STBY */ + >; + }; + + pinctrl_gpio_led: aristainetos3-gpio-led-grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16 0x19 + >; + }; + + pinctrl_gpio_led_proton2s: aristainetos3-gpio-proton2s-led-grp { + fsl,pins = < + MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06 0x19 + MX8MP_IOMUXC_SD1_DATA5__GPIO2_IO07 0x19 + >; + }; + + pinctrl_gpio_proton2s: aristainetos3-gpio-proton2s-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07 0x19 + >; + }; + + pinctrl_hdmi: aristainetos3-hdmi-grp { + fsl,pins = < + MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x400001c3 + MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x400001c3 + MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x40000019 + MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC 0x40000019 + >; + }; + + pinctrl_i2c1: aristainetos3-i2c1-grp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c3 + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c1_gpio: aristainetos3-i2c1-gpio-grp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14 0x1c3 + MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15 0x1c3 + >; + }; + + pinctrl_i2c2: aristainetos3-i2c2-grp { + fsl,pins = < + MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c3 + MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_i2c2_gpio: aristainetos3-i2c2-gpio-grp { + fsl,pins = < + MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16 0x1c3 + MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17 0x1c3 + >; + }; + + pinctrl_i2c3: aristainetos3-i2c3-grp { + fsl,pins = < + MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c3 + MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3_gpio: aristainetos3-i2c3-gpio-grp { + fsl,pins = < + MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18 0x1c3 + MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19 0x1c3 + >; + }; + + pinctrl_i2c5: aristainetos3-i2c5-grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_RXD0__I2C5_SCL 0x400001c3 + MX8MP_IOMUXC_SAI5_MCLK__I2C5_SDA 0x400001c3 + >; + }; + + pinctrl_i2c6: aristainetos3-i2c6-grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_RXFS__I2C6_SCL 0x400001c3 + MX8MP_IOMUXC_SAI5_RXC__I2C6_SDA 0x400001c3 + >; + }; + + pinctrl_i2c6_gpio: aristainetos3-i2c6-gpio-grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19 0x1c3 + MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20 0x1c3 + >; + }; + + pinctrl_i2c6_rtc_irq: aristainetos3-i2c6-rtc-irq-grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_RXD1__GPIO3_IO22 0xd6 + >; + }; + + pinctrl_i2c6_tpm_irq: aristainetos3-i2c6-tpm-irq-grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14 0xd6 + >; + }; + + pinctrl_lcd0_vdd_en: aristainetos3-lcd0-vdden-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13 0xd6 + >; + }; + + pinctrl_lcd1_vdd_en: aristainetos3-lcd1-vdden-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05 0xd6 + >; + }; + + pinctrl_lvds_pwr_en: aristainetos3-lvds-pwren-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10 0xd6 + >; + }; + + pinctrl_pcie: aristainetos3-pcie-grp { + fsl,pins = < + MX8MP_IOMUXC_I2C4_SCL__PCIE_CLKREQ_B 0x61 + MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20 0x41 + >; + }; + + pinctrl_pmic: aristainetos3-pmic-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41 + >; + }; + + pinctrl_pwm1: aristainetos3-pwm1-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO01__PWM1_OUT 0x116 + >; + }; + + pinctrl_pwm2: aristainetos3-pwm2-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO11__PWM2_OUT 0x116 + >; + }; + + pinctrl_uart1: aristainetos3-uart1-grp { + fsl,pins = < + MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x140 + MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x140 + >; + }; + + pinctrl_uart1_rs485: aristainetos3-uart1-rs485-grp { + fsl,pins = < + MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x140 + MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x140 + MX8MP_IOMUXC_SD1_DATA0__GPIO2_IO02 0x140 + >; + }; + + pinctrl_uart2: aristainetos3-uart2-grp { + fsl,pins = < + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x140 + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x140 + MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06 0x140 + MX8MP_IOMUXC_SD1_DATA5__UART2_DCE_CTS 0x140 + >; + }; + + pinctrl_uart3: aristainetos3-uart3-grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_ALE__UART3_DCE_RX 0x140 + MX8MP_IOMUXC_NAND_CE0_B__UART3_DCE_TX 0x140 + >; + }; + + pinctrl_uart3_rs485: aristainetos3-uart3-rs485-grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_ALE__UART3_DCE_RX 0x140 + MX8MP_IOMUXC_NAND_CE0_B__UART3_DCE_TX 0x140 + MX8MP_IOMUXC_SD1_RESET_B__GPIO2_IO10 0x140 + >; + }; + + pinctrl_uart4: aristainetos3-uart4-grp { + fsl,pins = < + MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x140 + MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x140 + MX8MP_IOMUXC_NAND_DATA03__GPIO3_IO09 0x140 + MX8MP_IOMUXC_NAND_DATA02__UART4_DCE_CTS 0x140 + >; + }; + + pinctrl_usb1_vbus: aristainetos3-usb1-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO14__GPIO1_IO14 0x19 + >; + }; + + pinctrl_usdhc1: aristainetos3-usdhc1-grp { + fsl,pins = < + MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x190 + MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d0 + MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d0 + MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d0 + MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d0 + MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc1_100mhz: aristainetos3-usdhc1-100mhz-grp { + fsl,pins = < + MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x194 + MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d4 + MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d4 + MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d4 + MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d4 + MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc1_200mhz: aristainetos3-usdhc1-200mhz-grp { + fsl,pins = < + MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x196 + MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d6 + MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d6 + MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d6 + MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d6 + MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2: aristainetos3-usdhc2-grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 + + >; + }; + + pinctrl_usdhc2_100mhz: aristainetos3-usdhc2-100mhz-grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_200mhz: aristainetos3-usdhc2-200mhz-grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_gpio: aristainetos3-usdhc2-gpio-grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x40000080 + >; + }; + + pinctrl_usdhc2_vmmc: aristainetos3-usdhc2-vmmc-grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41 + >; + }; + + pinctrl_usdhc3: aristainetos3-usdhc3-grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: aristainetos3-usdhc3-100mhz-grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: aristainetos3-usdhc3-200mhz-grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196 + >; + }; + + pinctrl_watchdog_gpio: aristainetos3-wdog-gpio-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06 0x19 + >; + }; + + pinctrl_wdog: aristainetos3-wdog-grp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6 + >; + }; +};
Add support for the i.MX8MP based aristainetos3 boards from ABB. The board uses a ABB specific SoM from ADLink, based on NXP i.MX8MP SoC. The SoM is used on 3 different carrier boards, with small differences, which are all catched up in devicetree overlays. The kernel image, the basic dtb and all dtbos are collected in a fitimage. As bootloader is used U-Boot which detects in his SPL stage the carrier board by probing some i2c devices. When the correct carrier is probed, the SPL applies all needed dtbos to the dtb with which U-Boot gets loaded. Same principle later before linux image boot, U-Boot applies the dtbos needed for the carrier board before booting Linux. Signed-off-by: Heiko Schocher <hs@denx.de> --- checkpatch dropped the following warnings: arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi:248: warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented -- check ./Documentation/devicetree/bindings/ ignored, as this compatible string is usedin other dts too, for example in arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi arch/arm64/boot/dts/freescale/Makefile | 5 + .../imx8mp-aristainetos3-adpismarc.dtsi | 64 + .../imx8mp-aristainetos3-adpismarc.dtso | 14 + .../imx8mp-aristainetos3-helios-lvds.dtsi | 89 ++ .../imx8mp-aristainetos3-helios-lvds.dtso | 13 + .../imx8mp-aristainetos3-helios.dtsi | 103 ++ .../imx8mp-aristainetos3-helios.dtso | 13 + .../imx8mp-aristainetos3-proton2s.dtsi | 176 +++ .../imx8mp-aristainetos3-proton2s.dtso | 13 + .../imx8mp-aristainetos3a-som-v1.dts | 18 + .../imx8mp-aristainetos3a-som-v1.dtsi | 1210 +++++++++++++++++ 11 files changed, 1718 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi