diff mbox series

[v5,01/10] dt-bindings: clock: renesas,r9a08g045-vbattb: Document VBATTB

Message ID 20241030110120.332802-2-claudiu.beznea.uj@bp.renesas.com (mailing list archive)
State New
Delegated to: Geert Uytterhoeven
Headers show
Series Add RTC support for the Renesas RZ/G3S SoC | expand

Commit Message

Claudiu Beznea Oct. 30, 2024, 11:01 a.m. UTC 
From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>

The VBATTB IP of the Renesas RZ/G3S SoC controls the clock for RTC,
the tamper detector and a small general usage memory of 128B.

The VBATTB controller controls the clock for the RTC on the Renesas
RZ/G3S. The HW block diagram for the clock logic is as follows:

           +----------+ XC   `\
RTXIN  --->|          |----->| \       +----+  VBATTCLK
           | 32K clock|      |  |----->|gate|----------->
           | osc      | XBYP |  |      +----+
RTXOUT --->|          |----->| /
           +----------+      ,/

One could connect as input to this HW block either a crystal or
an external clock device. This is board specific.

After discussions w/ Stephen Boyd the clock tree associated with this
hardware block was exported in Linux as:

input-xtal
  xbyp
  xc
     mux
        vbattclk

where:
- input-xtal is the input clock (connected to RTXIN, RTXOUT pins)
- xc, xbyp are mux inputs
- mux is the internal mux
- vbattclk is the gate clock that feeds in the end the RTC

to allow selecting the input of the MUX though assigned-clock DT
properties, using the already existing clock drivers and avoid adding
other DT properties.

This allows select the input of the mux based on the type of the
connected input clock:
- if the 32768 crystal is connected as input for the VBATTB,
  the input of the mux should be xc
- if an external clock device is connected as input for the VBATTB the
  input of the mux should be xbyp

Add bindings for the VBATTB controller.

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
---

Changes in v5:
- used spaces in the diagram from the patch description
- added "This is board specific" in the board description to emphasize
  the usage of the assigned-clocks in the example
- added default for quartz-load-femtofarads
- collected tags

Changes in v4:
- squashed with patch "Add clock IDs for the VBATTB controller" from v3
- removed "oscillator" word from commit description
- added assigned-clocks, assigned-clock-parents to the documentation example
- used clock-controller for the node name
- used "quartz-load-femtofarads" property for the load capacitance
- renamed include/dt-bindings/clock/r9a08g045-vbattb.h to
  include/dt-bindings/clock/renesas,r9a08g045-vbattb.h

Changes in v3:
- moved the file to clock dt bindings directory as it is the
  only functionality supported at the moment; the other functionalities
  (tamper detector, SRAM) are offered though register spreaded
  though the address space of the VBATTB IP and not actually
  individual devices; the other functionalities are not
  planned to be supported soon and if they will be I think they
  fit better on auxiliary bus than MFD
- dropped interrupt names as requested in the review process
- dropped the inner node for clock controller
- added #clock-cells
- added rtx clock
- updated description for renesas,vbattb-load-nanofarads
- included dt-bindings/interrupt-controller/irq.h in examples section

Changes in v2:
- changed file name and compatible
- updated title, description sections
- added clock controller part documentation and drop dedicated file
  for it included in v1
- used items to describe interrupts, interrupt-names, clocks, clock-names,
  resets
- dropped node labels and status
- updated clock-names for clock controller to cope with the new
  logic on detecting the necessity to setup bypass

 .../clock/renesas,r9a08g045-vbattb.yaml       | 84 +++++++++++++++++++
 .../clock/renesas,r9a08g045-vbattb.h          | 13 +++
 2 files changed, 97 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/renesas,r9a08g045-vbattb.yaml
 create mode 100644 include/dt-bindings/clock/renesas,r9a08g045-vbattb.h

Comments

Krzysztof Kozlowski Oct. 31, 2024, 7:46 a.m. UTC | #1 
On Wed, Oct 30, 2024 at 01:01:11PM +0200, Claudiu wrote:
> From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
> 
> The VBATTB IP of the Renesas RZ/G3S SoC controls the clock for RTC,
> the tamper detector and a small general usage memory of 128B.
> 
> The VBATTB controller controls the clock for the RTC on the Renesas
> RZ/G3S. The HW block diagram for the clock logic is as follows:
> 
>            +----------+ XC   `\
> RTXIN  --->|          |----->| \       +----+  VBATTCLK
>            | 32K clock|      |  |----->|gate|----------->
>            | osc      | XBYP |  |      +----+
> RTXOUT --->|          |----->| /
>            +----------+      ,/
> 
> One could connect as input to this HW block either a crystal or
> an external clock device. This is board specific.
> 
> After discussions w/ Stephen Boyd the clock tree associated with this
> hardware block was exported in Linux as:
> 
> input-xtal
>   xbyp
>   xc
>      mux
>         vbattclk
> 
> where:
> - input-xtal is the input clock (connected to RTXIN, RTXOUT pins)
> - xc, xbyp are mux inputs
> - mux is the internal mux
> - vbattclk is the gate clock that feeds in the end the RTC
> 
> to allow selecting the input of the MUX though assigned-clock DT
> properties, using the already existing clock drivers and avoid adding
> other DT properties.
> 
> This allows select the input of the mux based on the type of the
> connected input clock:
> - if the 32768 crystal is connected as input for the VBATTB,
>   the input of the mux should be xc
> - if an external clock device is connected as input for the VBATTB the
>   input of the mux should be xbyp
> 
> Add bindings for the VBATTB controller.
> 
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
> ---
> 
> Changes in v5:
> - used spaces in the diagram from the patch description
> - added "This is board specific" in the board description to emphasize
>   the usage of the assigned-clocks in the example
> - added default for quartz-load-femtofarads
> - collected tags

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/clock/renesas,r9a08g045-vbattb.yaml b/Documentation/devicetree/bindings/clock/renesas,r9a08g045-vbattb.yaml
new file mode 100644
index 000000000000..3707e4118949
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/renesas,r9a08g045-vbattb.yaml
@@ -0,0 +1,84 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/renesas,r9a08g045-vbattb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas Battery Backup Function (VBATTB)
+
+description:
+  Renesas VBATTB is an always on powered module (backed by battery) which
+  controls the RTC clock (VBATTCLK), tamper detection logic and a small
+  general usage memory (128B).
+
+maintainers:
+  - Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
+
+properties:
+  compatible:
+    const: renesas,r9a08g045-vbattb
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    items:
+      - description: tamper detector interrupt
+
+  clocks:
+    items:
+      - description: VBATTB module clock
+      - description: RTC input clock (crystal or external clock device)
+
+  clock-names:
+    items:
+      - const: bclk
+      - const: rtx
+
+  '#clock-cells':
+    const: 1
+
+  power-domains:
+    maxItems: 1
+
+  resets:
+    items:
+      - description: VBATTB module reset
+
+  quartz-load-femtofarads:
+    description: load capacitance of the on board crystal
+    enum: [ 4000, 7000, 9000, 12500 ]
+    default: 4000
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - '#clock-cells'
+  - power-domains
+  - resets
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/r9a08g045-cpg.h>
+    #include <dt-bindings/clock/renesas,r9a08g045-vbattb.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    clock-controller@1005c000 {
+        compatible = "renesas,r9a08g045-vbattb";
+        reg = <0x1005c000 0x1000>;
+        interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&cpg CPG_MOD R9A08G045_VBAT_BCLK>, <&vbattb_xtal>;
+        clock-names = "bclk", "rtx";
+        assigned-clocks = <&vbattb VBATTB_MUX>;
+        assigned-clock-parents = <&vbattb VBATTB_XC>;
+        #clock-cells = <1>;
+        power-domains = <&cpg>;
+        resets = <&cpg R9A08G045_VBAT_BRESETN>;
+        quartz-load-femtofarads = <12500>;
+    };
diff --git a/include/dt-bindings/clock/renesas,r9a08g045-vbattb.h b/include/dt-bindings/clock/renesas,r9a08g045-vbattb.h
new file mode 100644
index 000000000000..67774eafad06
--- /dev/null
+++ b/include/dt-bindings/clock/renesas,r9a08g045-vbattb.h
@@ -0,0 +1,13 @@ 
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+ *
+ * Copyright (C) 2024 Renesas Electronics Corp.
+ */
+#ifndef __DT_BINDINGS_CLOCK_R9A08G045_VBATTB_H__
+#define __DT_BINDINGS_CLOCK_R9A08G045_VBATTB_H__
+
+#define VBATTB_XC		0
+#define VBATTB_XBYP		1
+#define VBATTB_MUX		2
+#define VBATTB_VBATTCLK		3
+
+#endif /* __DT_BINDINGS_CLOCK_R9A08G045_VBATTB_H__ */