@@ -132,7 +132,6 @@ static const struct ucc_geth_info ugeth_primary_info = {
.transmitFlowControl = 1,
.maxGroupAddrInHash = 4,
.maxIndAddrInHash = 4,
- .prel = 7,
.maxFrameLength = 1518+16, /* Add extra bytes for VLANs etc. */
.minFrameLength = 64,
.maxD1Length = 1520+16, /* Add extra bytes for VLANs etc. */
@@ -1205,18 +1204,6 @@ static int init_mac_station_addr_regs(u8 address_byte_0,
return 0;
}
-static int init_preamble_length(u8 preamble_length,
- u32 __iomem *maccfg2_register)
-{
- if ((preamble_length < 3) || (preamble_length > 7))
- return -EINVAL;
-
- clrsetbits_be32(maccfg2_register, MACCFG2_PREL_MASK,
- preamble_length << MACCFG2_PREL_SHIFT);
-
- return 0;
-}
-
static int init_rx_parameters(int reject_broadcast,
int receive_short_frames,
int promiscuous, u32 __iomem *upsmr_register)
@@ -1276,7 +1263,6 @@ static int adjust_enet_interface(struct ucc_geth_private *ugeth)
struct ucc_geth_info *ug_info;
struct ucc_geth __iomem *ug_regs;
struct ucc_fast __iomem *uf_regs;
- int ret_val;
u32 upsmr, maccfg2;
u16 value;
@@ -1352,13 +1338,6 @@ static int adjust_enet_interface(struct ucc_geth_private *ugeth)
put_device(&tbiphy->mdio.dev);
}
- ret_val = init_preamble_length(ug_info->prel, &ug_regs->maccfg2);
- if (ret_val != 0) {
- if (netif_msg_probe(ugeth))
- pr_err("Preamble length must be between 3 and 7 inclusive\n");
- return ret_val;
- }
-
return 0;
}
@@ -921,7 +921,8 @@ struct ucc_geth_hardware_statistics {
#define UCC_GETH_UPSMR_INIT UCC_GETH_UPSMR_RES1
#define UCC_GETH_MACCFG1_INIT 0
-#define UCC_GETH_MACCFG2_INIT (MACCFG2_RESERVED_1)
+#define UCC_GETH_MACCFG2_INIT (MACCFG2_RESERVED_1 | \
+ (7 << MACCFG2_PREL_SHIFT))
/* Ethernet Address Type. */
enum enet_addr_type {
@@ -1113,7 +1114,6 @@ struct ucc_geth_info {
int transmitFlowControl;
u8 maxGroupAddrInHash;
u8 maxIndAddrInHash;
- u8 prel;
u16 maxFrameLength;
u16 minFrameLength;
u16 maxD1Length;
The preamble length can be configured in ucc_geth, however it just ends-up always being configured to 7 bytes, as nothing ever changes the default value of 7. Make that value the default value when the MACCFG2 register gets initialized, and remove the code to configure that value altogether. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> --- drivers/net/ethernet/freescale/ucc_geth.c | 21 --------------------- drivers/net/ethernet/freescale/ucc_geth.h | 4 ++-- 2 files changed, 2 insertions(+), 23 deletions(-)