@@ -16,12 +16,71 @@ / {
aliases {
serial0 = &uart1;
};
+
+ regulator_fixed_3p3: s3300 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-name = "fixed_3p3";
+ };
+
+ regulator_fixed_1p8: s1800 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-name = "fixed_1p8";
+ };
+
+ regulator_fixed_0p925: s0925 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <925000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-name = "fixed_0p925";
+ };
+
+};
+
+&dwc_0 {
+ dr_mode = "host";
+};
+
+&dwc_1 {
+ dr_mode = "host";
+};
+
+&qusb_phy_0 {
+ vdd-supply = <®ulator_fixed_0p925>;
+ vdda-pll-supply = <®ulator_fixed_1p8>;
+ vdda-phy-dpdm-supply = <®ulator_fixed_3p3>;
+
+ status = "okay";
+};
+
+&qusb_phy_1 {
+ vdd-supply = <®ulator_fixed_0p925>;
+ vdda-pll-supply = <®ulator_fixed_1p8>;
+ vdda-phy-dpdm-supply = <®ulator_fixed_3p3>;
+
+ status = "okay";
};
&sleep_clk {
clock-frequency = <32000>;
};
+&ssphy_0 {
+ vdda-pll-supply = <®ulator_fixed_1p8>;
+ vdda-phy-supply = <®ulator_fixed_0p925>;
+
+ status = "okay";
+};
+
&tlmm {
sdc_default_state: sdc-default-state {
clk-pins {
@@ -53,6 +112,14 @@ &uart1 {
status = "okay";
};
+&usb2 {
+ status = "okay";
+};
+
+&usb3 {
+ status = "okay";
+};
+
&xo_board {
clock-frequency = <24000000>;
};
@@ -233,6 +233,165 @@ intc: interrupt-controller@f200000 {
msi-controller;
};
+ qusb_phy_1: phy@71000 {
+ compatible = "qcom,ipq5424-qusb2-phy";
+ reg = <0 0x00071000 0 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
+ <&xo_board>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2_1_PHY_BCR>;
+ status = "disabled";
+ };
+
+ usb2: usb2@1e00000 {
+ compatible = "qcom,ipq5424-dwc3", "qcom,dwc3";
+ reg = <0 0x01ef8800 0 0x400>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_USB1_MASTER_CLK>,
+ <&gcc GCC_USB1_SLEEP_CLK>,
+ <&gcc GCC_USB1_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_CNOC_USB_CLK>;
+
+ clock-names = "core",
+ "sleep",
+ "mock_utmi",
+ "iface",
+ "cfg_noc";
+
+ assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>,
+ <&gcc GCC_USB1_MOCK_UTMI_CLK>;
+ assigned-clock-rates = <200000000>,
+ <24000000>;
+
+ interrupts-extended = <&intc GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 388 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "pwr_event",
+ "qusb2_phy",
+ "dm_hs_phy_irq",
+ "dp_hs_phy_irq";
+
+ resets = <&gcc GCC_USB1_BCR>;
+ qcom,select-utmi-as-pipe-clk;
+ status = "disabled";
+
+ dwc_1: usb@1e00000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x01e00000 0 0xe000>;
+ clocks = <&gcc GCC_USB1_MOCK_UTMI_CLK>;
+ clock-names = "ref";
+ interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&qusb_phy_1>;
+ phy-names = "usb2-phy";
+ tx-fifo-resize;
+ snps,is-utmi-l1-suspend;
+ snps,hird-threshold = /bits/ 8 <0x0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ };
+ };
+
+ qusb_phy_0: phy@7b000 {
+ compatible = "qcom,ipq5424-qusb2-phy";
+ reg = <0 0x0007b000 0 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
+ <&xo_board>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
+ status = "disabled";
+ };
+
+ ssphy_0: phy@7d000 {
+ compatible = "qcom,ipq5424-qmp-usb3-phy";
+ reg = <0 0x0007d000 0 0xa00>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB0_AUX_CLK>,
+ <&xo_board>,
+ <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_USB0_PIPE_CLK>;
+ clock-names = "aux",
+ "ref",
+ "cfg_ahb",
+ "pipe";
+
+ resets = <&gcc GCC_USB0_PHY_BCR>,
+ <&gcc GCC_USB3PHY_0_PHY_BCR>;
+ reset-names = "phy",
+ "phy_phy";
+
+ #clock-cells = <0>;
+ clock-output-names = "usb0_pipe_clk";
+
+ status = "disabled";
+ };
+
+ usb3: usb3@8a00000 {
+ compatible = "qcom,ipq5424-dwc3", "qcom,dwc3";
+ reg = <0 0x08af8800 0 0x400>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_USB0_MASTER_CLK>,
+ <&gcc GCC_USB0_SLEEP_CLK>,
+ <&gcc GCC_USB0_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_CNOC_USB_CLK>;
+
+ clock-names = "core",
+ "sleep",
+ "mock_utmi",
+ "iface",
+ "cfg_noc";
+
+ assigned-clocks = <&gcc GCC_USB0_MASTER_CLK>,
+ <&gcc GCC_USB0_MOCK_UTMI_CLK>;
+ assigned-clock-rates = <200000000>,
+ <24000000>;
+
+ interrupts-extended = <&intc GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "pwr_event",
+ "qusb2_phy",
+ "dm_hs_phy_irq",
+ "dp_hs_phy_irq";
+
+ resets = <&gcc GCC_USB_BCR>;
+ status = "disabled";
+
+ dwc_0: usb@8a00000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x08a00000 0 0xcd00>;
+ clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>;
+ clock-names = "ref";
+ interrupts = <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&qusb_phy_0>, <&ssphy_0>;
+ phy-names = "usb2-phy", "usb3-phy";
+ tx-fifo-resize;
+ snps,is-utmi-l1-suspend;
+ snps,hird-threshold = /bits/ 8 <0x0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ snps,dis-u1-entry-quirk;
+ snps,dis-u2-entry-quirk;
+ };
+ };
+
timer@f420000 {
compatible = "arm,armv7-timer-mem";
reg = <0 0xf420000 0 0x1000>;
The IPQ5424 SoC has both USB2.0 and USB3.0 controllers. The USB3.0 can connect to either of USB2.0 or USB3.0 phy and operate in the respective mode. Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> --- v2: Add dm/dp_hs_phy_irq to usb3@8a00000 node Add u1/u2-entry quirks to usb@8a00000 node --- arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts | 67 +++++++++ arch/arm64/boot/dts/qcom/ipq5424.dtsi | 159 ++++++++++++++++++++ 2 files changed, 226 insertions(+)