| Message ID | 20241128-qcs8300_initial_dtsi-v3-4-26aa8a164914@quicinc.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | Add initial support for QCS8300 SoC and QCS8300 RIDE board | expand |
On Thu, Nov 28, 2024 at 04:44:46PM +0800, Jingyi Wang wrote: > Add initial support for Qualcomm QCS8300 RIDE board which enables DSPs, > UFS and booting to shell with uart console. > > Written with help from Tingguo Cheng (added rpmhpd nodes) and Xin Liu > (added ufs, adsp and gpdsp nodes). > > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> > Signed-off-by: Jingyi Wang <quic_jingyw@quicinc.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 2 +- > arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 267 ++++++++++++++++++++++++++++++ > 2 files changed, 268 insertions(+), 1 deletion(-) > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 9bb8b191aeb5..d9545743606a 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -114,7 +114,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb > -dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb > +dtb-$(CONFIG_ARCH_QCOM) += qcs8300-ride.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb > dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb > diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts > new file mode 100644 > index 000000000000..7eed19a694c3 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts > @@ -0,0 +1,267 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > + > +#include "qcs8300.dtsi" > +/ { > + model = "Qualcomm Technologies, Inc. QCS8300 Ride"; > + compatible = "qcom,qcs8300-ride", "qcom,qcs8300"; > + chassis-type = "embedded"; > + > + aliases { > + serial0 = &uart7; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + clocks { > + xo_board_clk: xo-board-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <38400000>; > + }; > + > + sleep_clk: sleep-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <32000>; > + }; Move both clocks to the qcs8300.dtsi. If you wish, you can keep frequencies in the board DT file. > + }; > +}; > + > +&apps_rsc { > + regulators-0 { > + compatible = "qcom,pmm8654au-rpmh-regulators"; > + qcom,pmic-id = "a"; > + > + vreg_s4a: smps4 { > + regulator-name = "vreg_s4a"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s9a: smps9 { > + regulator-name = "vreg_s9a"; > + regulator-min-microvolt = <1352000>; > + regulator-max-microvolt = <1352000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3a: ldo3 { > + regulator-name = "vreg_l3a"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l4a: ldo4 { > + regulator-name = "vreg_l4a"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l5a: ldo5 { > + regulator-name = "vreg_l5a"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6a: ldo6 { > + regulator-name = "vreg_l6a"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7a: ldo7 { > + regulator-name = "vreg_l7a"; > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <912000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l8a: ldo8 { > + regulator-name = "vreg_l8a"; > + regulator-min-microvolt = <2504000>; > + regulator-max-microvolt = <2960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9a: ldo9 { > + regulator-name = "vreg_l9a"; > + regulator-min-microvolt = <2970000>; > + regulator-max-microvolt = <3072000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-1 { > + compatible = "qcom,pmm8654au-rpmh-regulators"; > + qcom,pmic-id = "c"; > + > + vreg_s5c: smps5 { > + regulator-name = "vreg_s5c"; > + regulator-min-microvolt = <1104000>; > + regulator-max-microvolt = <1104000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1c: ldo1 { > + regulator-name = "vreg_l1c"; > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <500000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2c: ldo2 { > + regulator-name = "vreg_l2c"; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <904000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l4c: ldo4 { > + regulator-name = "vreg_l4c"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6c: ldo6 { > + regulator-name = "vreg_l6c"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7c: ldo7 { > + regulator-name = "vreg_l7c"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l8c: ldo8 { > + regulator-name = "vreg_l8c"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9c: ldo9 { > + regulator-name = "vreg_l9c"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-allow-set-load; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM > + RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > +}; > + > +&gcc { > + clocks = <&rpmhcc RPMH_CXO_CLK>, > + <&sleep_clk>, > + <0>, > + <0>, > + <0>, > + <0>, > + <0>, > + <0>, > + <0>, > + <0>; Move this to the qcs8300.dtsi (and rpmhcc too). > +}; > + > +&qupv3_id_0 { > + status = "okay"; > +}; > + > +&remoteproc_adsp { > + firmware-name = "qcom/qcs8300/adsp.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_cdsp { > + firmware-name = "qcom/qcs8300/cdsp0.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_gpdsp { > + firmware-name = "qcom/qcs8300/gpdsp0.mbn"; > + status = "okay"; > +}; > + > +&rpmhcc { > + clocks = <&xo_board_clk>; > + clock-names = "xo"; qcs8300.dtsi > +}; > + > +&uart7 { > + status = "okay"; > +}; > + > +&ufs_mem_hc { > + reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>; > + vcc-supply = <&vreg_l8a>; > + vcc-max-microamp = <1100000>; > + vccq-supply = <&vreg_l4c>; > + vccq-max-microamp = <1200000>; > + status = "okay"; > +}; > + > +&ufs_mem_phy { > + vdda-phy-supply = <&vreg_l4a>; > + vdda-pll-supply = <&vreg_l5a>; > + status = "okay"; > +}; > > -- > 2.25.1 >
On Thu, Nov 28, 2024 at 04:44:46PM +0800, Jingyi Wang wrote: > Add initial support for Qualcomm QCS8300 RIDE board which enables DSPs, > UFS and booting to shell with uart console. > > Written with help from Tingguo Cheng (added rpmhpd nodes) and Xin Liu > (added ufs, adsp and gpdsp nodes). > > Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> > Signed-off-by: Jingyi Wang <quic_jingyw@quicinc.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 2 +- > arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 267 ++++++++++++++++++++++++++++++ > 2 files changed, 268 insertions(+), 1 deletion(-) > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 9bb8b191aeb5..d9545743606a 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -114,7 +114,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb > -dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb > +dtb-$(CONFIG_ARCH_QCOM) += qcs8300-ride.dtb It would be good to add a comment to the commit message about why you are removing qcs8550-aim300-aiot.dtb from the Makefile. Andrew
On 28/11/2024 17:49, Andrew Lunn wrote: > On Thu, Nov 28, 2024 at 04:44:46PM +0800, Jingyi Wang wrote: >> Add initial support for Qualcomm QCS8300 RIDE board which enables DSPs, >> UFS and booting to shell with uart console. >> >> Written with help from Tingguo Cheng (added rpmhpd nodes) and Xin Liu >> (added ufs, adsp and gpdsp nodes). >> >> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> >> Signed-off-by: Jingyi Wang <quic_jingyw@quicinc.com> >> --- >> arch/arm64/boot/dts/qcom/Makefile | 2 +- >> arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 267 ++++++++++++++++++++++++++++++ >> 2 files changed, 268 insertions(+), 1 deletion(-) >> >> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile >> index 9bb8b191aeb5..d9545743606a 100644 >> --- a/arch/arm64/boot/dts/qcom/Makefile >> +++ b/arch/arm64/boot/dts/qcom/Makefile >> @@ -114,7 +114,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb >> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb >> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb >> dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb >> -dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb >> +dtb-$(CONFIG_ARCH_QCOM) += qcs8300-ride.dtb > > It would be good to add a comment to the commit message about why you > are removing qcs8550-aim300-aiot.dtb from the Makefile. Especially that it was not in v2 (which I reviewed) and nothing in the changelog explains this removal. Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 9bb8b191aeb5..d9545743606a 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -114,7 +114,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb -dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb +dtb-$(CONFIG_ARCH_QCOM) += qcs8300-ride.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts new file mode 100644 index 000000000000..7eed19a694c3 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts @@ -0,0 +1,267 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "qcs8300.dtsi" +/ { + model = "Qualcomm Technologies, Inc. QCS8300 Ride"; + compatible = "qcom,qcs8300-ride", "qcom,qcs8300"; + chassis-type = "embedded"; + + aliases { + serial0 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32000>; + }; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pmm8654au-rpmh-regulators"; + qcom,pmic-id = "a"; + + vreg_s4a: smps4 { + regulator-name = "vreg_s4a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s9a: smps9 { + regulator-name = "vreg_s9a"; + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3a: ldo3 { + regulator-name = "vreg_l3a"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4a: ldo4 { + regulator-name = "vreg_l4a"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5a: ldo5 { + regulator-name = "vreg_l5a"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6a: ldo6 { + regulator-name = "vreg_l6a"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a: ldo7 { + regulator-name = "vreg_l7a"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a: ldo8 { + regulator-name = "vreg_l8a"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9a: ldo9 { + regulator-name = "vreg_l9a"; + regulator-min-microvolt = <2970000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pmm8654au-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_s5c: smps5 { + regulator-name = "vreg_s5c"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c: ldo1 { + regulator-name = "vreg_l1c"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <500000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c: ldo2 { + regulator-name = "vreg_l2c"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4c: ldo4 { + regulator-name = "vreg_l4c"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6c: ldo6 { + regulator-name = "vreg_l6c"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c: ldo7 { + regulator-name = "vreg_l7c"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c: ldo8 { + regulator-name = "vreg_l8c"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c: ldo9 { + regulator-name = "vreg_l9c"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gcc { + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&sleep_clk>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/qcs8300/adsp.mbn"; + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/qcs8300/cdsp0.mbn"; + status = "okay"; +}; + +&remoteproc_gpdsp { + firmware-name = "qcom/qcs8300/gpdsp0.mbn"; + status = "okay"; +}; + +&rpmhcc { + clocks = <&xo_board_clk>; + clock-names = "xo"; +}; + +&uart7 { + status = "okay"; +}; + +&ufs_mem_hc { + reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>; + vcc-supply = <&vreg_l8a>; + vcc-max-microamp = <1100000>; + vccq-supply = <&vreg_l4c>; + vccq-max-microamp = <1200000>; + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l4a>; + vdda-pll-supply = <&vreg_l5a>; + status = "okay"; +};