| Message ID | 20250220152640.49010-4-john.madieu.xa@bp.renesas.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | thermal: renesas: Add support fot RZ/G3E | expand |
On Thu, 20 Feb 2025 16:26:08 +0100, John Madieu wrote: > The Renesas RZ/G3E SoC includes a Thermal Sensor Unit (TSU) block designed > to measure the junction temperature. The device provides real-time temperature > measurements for thermal management, utilizing a single dedicated channel > (channel 1) for temperature sensing. > > Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com> > --- > .../thermal/renesas,r9a09g047-tsu.yaml | 123 ++++++++++++++++++ > 1 file changed, 123 insertions(+) > create mode 100644 Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml > My bot found errors running 'make dt_binding_check' on your patch: yamllint warnings/errors: dtschema/dtc warnings/errors: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.example.dtb: thermal@14002000: reg: [[0, 335552512], [0, 4096]] is too long from schema $id: http://devicetree.org/schemas/thermal/renesas,r9a09g047-tsu.yaml# doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20250220152640.49010-4-john.madieu.xa@bp.renesas.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
On Thu, Feb 20, 2025 at 04:26:08PM +0100, John Madieu wrote: > The Renesas RZ/G3E SoC includes a Thermal Sensor Unit (TSU) block designed > to measure the junction temperature. The device provides real-time temperature > measurements for thermal management, utilizing a single dedicated channel > (channel 1) for temperature sensing. > > Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com> > --- > .../thermal/renesas,r9a09g047-tsu.yaml | 123 ++++++++++++++++++ > 1 file changed, 123 insertions(+) > create mode 100644 Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml > > diff --git a/Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml b/Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml > new file mode 100644 > index 000000000000..dbd3860a31d0 > --- /dev/null > +++ b/Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml > @@ -0,0 +1,123 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/thermal/renesas,r9a09g047-tsu.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Renesas RZ/G3E Temperature Sensor Unit (TSU) > + > +maintainers: > + - John Madieu <john.madieu.xa@bp.renesas.com> > + > +description: | Don't need '|' if there is no formatting to preserve. > + The Temperature Sensor Unit (TSU) is an integrated thermal sensor that monitors Wrap lines at <80 char. > + the chip temperature on the Renesas RZ/G3E SoC. The TSU provides real-time > + temperature measurements for thermal management. > + > +properties: > + compatible: > + const: renesas,r9a09g047-tsu > + > + reg: > + maxItems: 1 > + > + clocks: > + maxItems: 1 > + > + resets: > + maxItems: 1 > + > + power-domains: > + maxItems: 1 > + > + interrupts: > + description: | > + Interrupt specifiers for the TSU: > + - S12TSUADI1: Conversion complete interrupt signal (pulse) > + - S12TSUADCMPI1: Comparison result interrupt signal (level) > + > + interrupt-names: > + items: > + - const: S12TSUADI1 > + - const: S12TSUADCMPI1 Odd names for the interrupts... 'S12TSUAD' is the same for both, so that part is redundant from my perspective. I guess if these strings are meaningful for anyone familiar with this h/w, then it's fine. > + > + "#thermal-sensor-cells": > + const: 0 > + > + renesas,tsu-calibration-sys: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: | > + Phandle to the system controller (sys) that contains the TSU > + calibration values used for temperature calculations. > + > + renesas,tsu-operating-mode: > + $ref: /schemas/types.yaml#/definitions/uint32 > + enum: [0, 1] > + description: | > + TSU operating mode: > + 0: Mode 0 - Conversion started by software > + 1: Mode 1 - Conversion started by ELC trigger > + > +required: > + - compatible > + - reg > + - clocks > + - resets > + - power-domains > + - interrupts > + - interrupt-names > + - "#thermal-sensor-cells" > + - renesas,tsu-operating-mode > + - renesas,tsu-calibration-sys > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/renesas,r9a09g047-cpg.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + > + tsu: thermal@14002000 { > + compatible = "renesas,r9a09g047-tsu"; > + reg = <0 0x14002000 0 0x1000>; > + clocks = <&cpg CPG_MOD 0x10a>; > + resets = <&cpg 0xf8>; > + power-domains = <&cpg>; > + interrupts = <GIC_SPI 250 IRQ_TYPE_EDGE_RISING>, > + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "S12TSUADI1", "S12TSUADCMPI1"; > + #thermal-sensor-cells = <0>; > + renesas,tsu-operating-mode = <0>; > + renesas,tsu-calibration-sys = <&sys>; > + }; > + > + thermal-zones { > + cpu-thermal { > + polling-delay = <1000>; > + polling-delay-passive = <250>; > + thermal-sensors = <&tsu>; > + > + cooling-maps { > + map0 { > + trip = <&target>; > + cooling-device = <&cpu0 0 3>, <&cpu1 0 3>, > + <&cpu2 0 3>, <&cpu3 0 3>; > + contribution = <1024>; > + }; > + }; > + > + trips { > + target: trip-point { > + temperature = <95000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + > + sensor_crit: sensor-crit { > + temperature = <120000>; > + hysteresis = <1000>; > + type = "critical"; > + }; > + }; > + }; > + }; > -- > 2.25.1 >
diff --git a/Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml b/Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml new file mode 100644 index 000000000000..dbd3860a31d0 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml @@ -0,0 +1,123 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/renesas,r9a09g047-tsu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas RZ/G3E Temperature Sensor Unit (TSU) + +maintainers: + - John Madieu <john.madieu.xa@bp.renesas.com> + +description: | + The Temperature Sensor Unit (TSU) is an integrated thermal sensor that monitors + the chip temperature on the Renesas RZ/G3E SoC. The TSU provides real-time + temperature measurements for thermal management. + +properties: + compatible: + const: renesas,r9a09g047-tsu + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + power-domains: + maxItems: 1 + + interrupts: + description: | + Interrupt specifiers for the TSU: + - S12TSUADI1: Conversion complete interrupt signal (pulse) + - S12TSUADCMPI1: Comparison result interrupt signal (level) + + interrupt-names: + items: + - const: S12TSUADI1 + - const: S12TSUADCMPI1 + + "#thermal-sensor-cells": + const: 0 + + renesas,tsu-calibration-sys: + $ref: /schemas/types.yaml#/definitions/phandle + description: | + Phandle to the system controller (sys) that contains the TSU + calibration values used for temperature calculations. + + renesas,tsu-operating-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + description: | + TSU operating mode: + 0: Mode 0 - Conversion started by software + 1: Mode 1 - Conversion started by ELC trigger + +required: + - compatible + - reg + - clocks + - resets + - power-domains + - interrupts + - interrupt-names + - "#thermal-sensor-cells" + - renesas,tsu-operating-mode + - renesas,tsu-calibration-sys + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/renesas,r9a09g047-cpg.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + tsu: thermal@14002000 { + compatible = "renesas,r9a09g047-tsu"; + reg = <0 0x14002000 0 0x1000>; + clocks = <&cpg CPG_MOD 0x10a>; + resets = <&cpg 0xf8>; + power-domains = <&cpg>; + interrupts = <GIC_SPI 250 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "S12TSUADI1", "S12TSUADCMPI1"; + #thermal-sensor-cells = <0>; + renesas,tsu-operating-mode = <0>; + renesas,tsu-calibration-sys = <&sys>; + }; + + thermal-zones { + cpu-thermal { + polling-delay = <1000>; + polling-delay-passive = <250>; + thermal-sensors = <&tsu>; + + cooling-maps { + map0 { + trip = <&target>; + cooling-device = <&cpu0 0 3>, <&cpu1 0 3>, + <&cpu2 0 3>, <&cpu3 0 3>; + contribution = <1024>; + }; + }; + + trips { + target: trip-point { + temperature = <95000>; + hysteresis = <1000>; + type = "passive"; + }; + + sensor_crit: sensor-crit { + temperature = <120000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + };
The Renesas RZ/G3E SoC includes a Thermal Sensor Unit (TSU) block designed to measure the junction temperature. The device provides real-time temperature measurements for thermal management, utilizing a single dedicated channel (channel 1) for temperature sensing. Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com> --- .../thermal/renesas,r9a09g047-tsu.yaml | 123 ++++++++++++++++++ 1 file changed, 123 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml