| Message ID | 20250220143354.2532448-1-macpaul.lin@mediatek.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | [v4,1/2] arm64: dts: mediatek: mt8395-genio-1200-evk: add support for TCPC port | expand |
Il 20/02/25 15:33, Macpaul Lin ha scritto: > From: Fabien Parent <fparent@baylibre.com> > > Enable USB Type-C support on MediaTek MT8395 Genio 1200 EVK by adding > configuration for TCPC Port, USB-C connector, and related settings. > > Configure dual role switch capability, set up PD (Power Delivery) profiles, > and establish endpoints for SS (SuperSpeed) and HS (HighSpeed) USB. > > Update pinctrl configurations for U3 P0 VBus default pins and set dr_mode > to "otg" for OTG (On-The-Go) mode operation. > > Signed-off-by: Fabien Parent <fparent@baylibre.com> > Signed-off-by: Yow-Shin Liou <yow-shin.liou@mediatek.com> > Signed-off-by: Simon Sun <simon.sun@yunjingtech.com> > Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> > --- > .../dts/mediatek/mt8395-genio-1200-evk.dts | 72 +++++++++++++++++++ > 1 file changed, 72 insertions(+) > > Changes for v2: > - Drop the no need '1/2' DT Schema update patch in the 1st version. > - Fix indent for 'ports' node, it should under the 'connector' node. > - Correct the index for 'port@0' and 'port@1' node. > > Changes for v3: > - Correct the order between new added nodes. > > Changes for v4: > - Reorder for property 'op-sink-microwatt'. > - Fix indentation for 'source-pdos' and 'sink-pdos' nodes. > - Correct node 'pin-cmd-dat' with 'pins-vbus'. > - Add both Highspeed and Superspeed ports to ssusb0 port. > - Set 'role-switch-default-mode' = "peripheral" for ssusb0 port. > - Rename endpoint of USB data port to 'mtu3_hs0_role_sw' and > 'mtu3_ss0_role_sw'. > > diff --git a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts > index 1ef6262b65c9..ca039c8e4c71 100644 > --- a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts > +++ b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts > @@ -330,6 +330,47 @@ mt6360_ldo7: ldo7 { > regulator-always-on; > }; > }; > + > + tcpc { > + compatible = "mediatek,mt6360-tcpc"; > + interrupts-extended = <&pio 17 IRQ_TYPE_LEVEL_LOW>; > + interrupt-names = "PD_IRQB"; > + > + connector { > + compatible = "usb-c-connector"; > + label = "USB-C"; > + data-role = "dual"; > + op-sink-microwatt = <10000000>; > + power-role = "dual"; > + try-power-role = "sink"; Would be appreciated if you could also complete the node by adding the pd-revision property, enabling full USBC Power Delivery for the MT6360 PMIC. Same for the alternate modes, adding the DP alt mode is a matter of seconds... and well, it does sound a bit weird to add alternate modes without a mux... so, in this case you can choose either to: - Squash the two commits (tcpc, it5205) and do everything in one; or - Add the alternate mode node to the connector in the commit introducing the mux. Either of the two options is okay for me, so you choose. > + > + source-pdos = <PDO_FIXED(5000, 1000, > + PDO_FIXED_DUAL_ROLE | > + PDO_FIXED_DATA_SWAP)>; > + sink-pdos = <PDO_FIXED(5000, 2000, > + PDO_FIXED_DUAL_ROLE | > + PDO_FIXED_DATA_SWAP)>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + typec_con_hs: endpoint { > + remote-endpoint = <&mtu3_hs0_role_sw>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + typec_con_ss: endpoint { > + remote-endpoint = <&mtu3_ss0_role_sw>; > + }; > + }; > + }; > + }; > + }; > }; > }; > > @@ -755,6 +796,13 @@ pins-reset { > }; > }; > > + u3_p0_vbus: u3-p0-vbus-default-pins { > + pins-vbus { > + pinmux = <PINMUX_GPIO63__FUNC_VBUSVALID>; > + input-enable; > + }; > + }; > + > uart0_pins: uart0-pins { > pins { > pinmux = <PINMUX_GPIO98__FUNC_UTXD0>, > @@ -885,8 +933,32 @@ &ufsphy { > }; > > &ssusb0 { > + dr_mode = "otg"; > + pinctrl-names = "default"; > + pinctrl-0 = <&u3_p0_vbus>; > + role-switch-default-mode = "peripheral"; There's no need for a default mode here, luckily the MediaTek MTU3 controllers don't need that for real :-) Drop please. Cheers, Angelo
On Thu, 20 Feb 2025 22:33:53 +0800, Macpaul Lin wrote: > From: Fabien Parent <fparent@baylibre.com> > > Enable USB Type-C support on MediaTek MT8395 Genio 1200 EVK by adding > configuration for TCPC Port, USB-C connector, and related settings. > > Configure dual role switch capability, set up PD (Power Delivery) profiles, > and establish endpoints for SS (SuperSpeed) and HS (HighSpeed) USB. > > Update pinctrl configurations for U3 P0 VBus default pins and set dr_mode > to "otg" for OTG (On-The-Go) mode operation. > > Signed-off-by: Fabien Parent <fparent@baylibre.com> > Signed-off-by: Yow-Shin Liou <yow-shin.liou@mediatek.com> > Signed-off-by: Simon Sun <simon.sun@yunjingtech.com> > Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> > --- > .../dts/mediatek/mt8395-genio-1200-evk.dts | 72 +++++++++++++++++++ > 1 file changed, 72 insertions(+) > > Changes for v2: > - Drop the no need '1/2' DT Schema update patch in the 1st version. > - Fix indent for 'ports' node, it should under the 'connector' node. > - Correct the index for 'port@0' and 'port@1' node. > > Changes for v3: > - Correct the order between new added nodes. > > Changes for v4: > - Reorder for property 'op-sink-microwatt'. > - Fix indentation for 'source-pdos' and 'sink-pdos' nodes. > - Correct node 'pin-cmd-dat' with 'pins-vbus'. > - Add both Highspeed and Superspeed ports to ssusb0 port. > - Set 'role-switch-default-mode' = "peripheral" for ssusb0 port. > - Rename endpoint of USB data port to 'mtu3_hs0_role_sw' and > 'mtu3_ss0_role_sw'. > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/mediatek/' for 20250220143354.2532448-1-macpaul.lin@mediatek.com: arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dtb: usb@11201000: 'ports' does not match any of the regexes: '^usb@[0-9a-f]+$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/usb/mediatek,mtu3.yaml#
On Thu, 2025-02-20 at 16:58 +0100, AngeloGioacchino Del Regno wrote: > > [snip] > > + tcpc { > > + compatible = "mediatek,mt6360-tcpc"; > > + interrupts-extended = <&pio 17 > > IRQ_TYPE_LEVEL_LOW>; > > + interrupt-names = "PD_IRQB"; > > + > > + connector { > > + compatible = "usb-c-connector"; > > + label = "USB-C"; > > + data-role = "dual"; > > + op-sink-microwatt = <10000000>; > > + power-role = "dual"; > > + try-power-role = "sink"; > > Would be appreciated if you could also complete the node by adding > the pd-revision > property, enabling full USBC Power Delivery for the MT6360 PMIC. > Well, I have no idea about the pd-revision of MT6360. I could found MT6360 supports PD 3.0 according to the datasheet, however, I have no idea about the other fields like major and minor values. Dear ChiYuan, could you help to provide the value of pd- revision? The property has been defined in Documentation/devicetree/bindings/connector/usb-connector.yaml. > Same for the alternate modes, adding the DP alt mode is a matter of > seconds... and > well, it does sound a bit weird to add alternate modes without a > mux... so, in this > case you can choose either to: > - Squash the two commits (tcpc, it5205) and do everything in one; > or > - Add the alternate mode node to the connector in the commit > introducing the mux. > > Either of the two options is okay for me, so you choose. > > Well, I could squash the two commits together and adding the DP alt mode values in next version. > > > > &ssusb0 { > > + dr_mode = "otg"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&u3_p0_vbus>; > > + role-switch-default-mode = "peripheral"; > > There's no need for a default mode here, luckily the MediaTek MTU3 > controllers > don't need that for real :-) Okay, will drop it than. Thanks. Macpaul Lin > Drop please. > > Cheers, > Angelo > >
diff --git a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts index 1ef6262b65c9..ca039c8e4c71 100644 --- a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts +++ b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts @@ -330,6 +330,47 @@ mt6360_ldo7: ldo7 { regulator-always-on; }; }; + + tcpc { + compatible = "mediatek,mt6360-tcpc"; + interrupts-extended = <&pio 17 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "PD_IRQB"; + + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + op-sink-microwatt = <10000000>; + power-role = "dual"; + try-power-role = "sink"; + + source-pdos = <PDO_FIXED(5000, 1000, + PDO_FIXED_DUAL_ROLE | + PDO_FIXED_DATA_SWAP)>; + sink-pdos = <PDO_FIXED(5000, 2000, + PDO_FIXED_DUAL_ROLE | + PDO_FIXED_DATA_SWAP)>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + typec_con_hs: endpoint { + remote-endpoint = <&mtu3_hs0_role_sw>; + }; + }; + + port@1 { + reg = <1>; + typec_con_ss: endpoint { + remote-endpoint = <&mtu3_ss0_role_sw>; + }; + }; + }; + }; + }; }; }; @@ -755,6 +796,13 @@ pins-reset { }; }; + u3_p0_vbus: u3-p0-vbus-default-pins { + pins-vbus { + pinmux = <PINMUX_GPIO63__FUNC_VBUSVALID>; + input-enable; + }; + }; + uart0_pins: uart0-pins { pins { pinmux = <PINMUX_GPIO98__FUNC_UTXD0>, @@ -885,8 +933,32 @@ &ufsphy { }; &ssusb0 { + dr_mode = "otg"; + pinctrl-names = "default"; + pinctrl-0 = <&u3_p0_vbus>; + role-switch-default-mode = "peripheral"; + usb-role-switch; vusb33-supply = <&mt6359_vusb_ldo_reg>; status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mtu3_hs0_role_sw: endpoint { + remote-endpoint = <&typec_con_hs>; + }; + }; + + port@1 { + reg = <1>; + mtu3_ss0_role_sw: endpoint { + remote-endpoint = <&typec_con_ss>; + }; + }; + }; }; &ssusb2 {