diff mbox series

[v2] usbnet: asix AX88772: leave the carrier control to phylink

Message ID m3plhmdfte.fsf_-_@t19.piap.pl (mailing list archive)
State New
Headers show
Series [v2] usbnet: asix AX88772: leave the carrier control to phylink | expand

Commit Message

Krzysztof Hałasa April 8, 2025, 11:59 a.m. UTC 
ASIX AX88772B based USB 10/100 Ethernet adapter doesn't come
up ("carrier off"), despite the built-in 100BASE-FX PHY positive link
indication. The internal PHY is configured (using EEPROM) in fixed
100 Mbps full duplex mode.

The primary problem appears to be using carrier_netif_{on,off}() while,
at the same time, delegating carrier management to phylink. Use only the
latter and remove "manual control" in the asix driver.

I don't have any other AX88772 board here, but the problem doesn't seem
specific to a particular board or settings - it's probably
timing-dependent.

Remove unused asix_adjust_link() as well.

Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>

Comments

Jakub Kicinski April 8, 2025, 3:22 p.m. UTC | #1 
On Tue, 08 Apr 2025 13:59:41 +0200 Krzysztof Hałasa wrote:
> ASIX AX88772B based USB 10/100 Ethernet adapter doesn't come
> up ("carrier off"), despite the built-in 100BASE-FX PHY positive link
> indication. The internal PHY is configured (using EEPROM) in fixed
> 100 Mbps full duplex mode.
> 
> The primary problem appears to be using carrier_netif_{on,off}() while,
> at the same time, delegating carrier management to phylink. Use only the
> latter and remove "manual control" in the asix driver.
> 
> I don't have any other AX88772 board here, but the problem doesn't seem
> specific to a particular board or settings - it's probably
> timing-dependent.
> 
> Remove unused asix_adjust_link() as well.
> 
> Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>

In the future, if you don't mind, please add a lore link here, like
this:
---
v1: https://lore.kernel.org/all/m35xjgdvih.fsf@t19.piap.pl/

Sending in-reply-to is discouraged, it messes up patch ordering for
reviewers:
https://www.kernel.org/doc/html/next/process/maintainer-netdev.html#resending-after-review
Oleksij Rempel April 10, 2025, 12:14 p.m. UTC | #2 
On Tue, Apr 08, 2025 at 01:59:41PM +0200, Krzysztof Hałasa wrote:
> ASIX AX88772B based USB 10/100 Ethernet adapter doesn't come
> up ("carrier off"), despite the built-in 100BASE-FX PHY positive link
> indication. The internal PHY is configured (using EEPROM) in fixed
> 100 Mbps full duplex mode.
> 
> The primary problem appears to be using carrier_netif_{on,off}() while,
> at the same time, delegating carrier management to phylink. Use only the
> latter and remove "manual control" in the asix driver.
> 
> I don't have any other AX88772 board here, but the problem doesn't seem
> specific to a particular board or settings - it's probably
> timing-dependent.
> 
> Remove unused asix_adjust_link() as well.
> 
> Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>

Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
 
Link detection is still working on variants with copper interface.

Thank you!

Best Regards,
Oleksij
patchwork-bot+netdevbpf@kernel.org April 11, 2025, 2:20 a.m. UTC | #3 
Hello:

This patch was applied to netdev/net-next.git (main)
by Jakub Kicinski <kuba@kernel.org>:

On Tue, 08 Apr 2025 13:59:41 +0200 you wrote:
> ASIX AX88772B based USB 10/100 Ethernet adapter doesn't come
> up ("carrier off"), despite the built-in 100BASE-FX PHY positive link
> indication. The internal PHY is configured (using EEPROM) in fixed
> 100 Mbps full duplex mode.
> 
> The primary problem appears to be using carrier_netif_{on,off}() while,
> at the same time, delegating carrier management to phylink. Use only the
> latter and remove "manual control" in the asix driver.
> 
> [...]

Here is the summary with links:
  - [v2] usbnet: asix AX88772: leave the carrier control to phylink
    https://git.kernel.org/netdev/net-next/c/4145f00227ee

You are awesome, thank you!
diff mbox series

Patch

--- a/drivers/net/usb/asix.h
+++ b/drivers/net/usb/asix.h
@@ -224,7 +224,6 @@  int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm);
 
 u16 asix_read_medium_status(struct usbnet *dev, int in_pm);
 int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm);
-void asix_adjust_link(struct net_device *netdev);
 
 int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm);
 
--- a/drivers/net/usb/asix_common.c
+++ b/drivers/net/usb/asix_common.c
@@ -414,28 +414,6 @@  int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm)
 	return ret;
 }
 
-/* set MAC link settings according to information from phylib */
-void asix_adjust_link(struct net_device *netdev)
-{
-	struct phy_device *phydev = netdev->phydev;
-	struct usbnet *dev = netdev_priv(netdev);
-	u16 mode = 0;
-
-	if (phydev->link) {
-		mode = AX88772_MEDIUM_DEFAULT;
-
-		if (phydev->duplex == DUPLEX_HALF)
-			mode &= ~AX_MEDIUM_FD;
-
-		if (phydev->speed != SPEED_100)
-			mode &= ~AX_MEDIUM_PS;
-	}
-
-	asix_write_medium_mode(dev, mode, 0);
-	phy_print_status(phydev);
-	usbnet_link_change(dev, phydev->link, 0);
-}
-
 int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm)
 {
 	int ret;
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -752,7 +736,6 @@  static void ax88772_mac_link_down(struct phylink_config *config,
 	struct usbnet *dev = netdev_priv(to_net_dev(config->dev));
 
 	asix_write_medium_mode(dev, 0, 0);
-	usbnet_link_change(dev, false, false);
 }
 
 static void ax88772_mac_link_up(struct phylink_config *config,
@@ -783,7 +766,6 @@  static void ax88772_mac_link_up(struct phylink_config *config,
 		m |= AX_MEDIUM_RFC;
 
 	asix_write_medium_mode(dev, m, 0);
-	usbnet_link_change(dev, true, false);
 }
 
 static const struct phylink_mac_ops ax88772_phylink_mac_ops = {
@@ -1350,10 +1328,9 @@  static const struct driver_info ax88772_info = {
 	.description = "ASIX AX88772 USB 2.0 Ethernet",
 	.bind = ax88772_bind,
 	.unbind = ax88772_unbind,
-	.status = asix_status,
 	.reset = ax88772_reset,
 	.stop = ax88772_stop,
-	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | FLAG_MULTI_PACKET,
+	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_MULTI_PACKET,
 	.rx_fixup = asix_rx_fixup_common,
 	.tx_fixup = asix_tx_fixup,
 };
@@ -1362,11 +1339,9 @@  static const struct driver_info ax88772b_info = {
 	.description = "ASIX AX88772B USB 2.0 Ethernet",
 	.bind = ax88772_bind,
 	.unbind = ax88772_unbind,
-	.status = asix_status,
 	.reset = ax88772_reset,
 	.stop = ax88772_stop,
-	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |
-	         FLAG_MULTI_PACKET,
+	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_MULTI_PACKET,
 	.rx_fixup = asix_rx_fixup_common,
 	.tx_fixup = asix_tx_fixup,
 	.data = FLAG_EEPROM_MAC,
@@ -1376,11 +1351,9 @@  static const struct driver_info lxausb_t1l_info = {
 	.description = "Linux Automation GmbH USB 10Base-T1L",
 	.bind = ax88772_bind,
 	.unbind = ax88772_unbind,
-	.status = asix_status,
 	.reset = ax88772_reset,
 	.stop = ax88772_stop,
-	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |
-		 FLAG_MULTI_PACKET,
+	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_MULTI_PACKET,
 	.rx_fixup = asix_rx_fixup_common,
 	.tx_fixup = asix_tx_fixup,
 	.data = FLAG_EEPROM_MAC,
@@ -1412,10 +1383,8 @@  static const struct driver_info hg20f9_info = {
 	.description = "HG20F9 USB 2.0 Ethernet",
 	.bind = ax88772_bind,
 	.unbind = ax88772_unbind,
-	.status = asix_status,
 	.reset = ax88772_reset,
-	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |
-	         FLAG_MULTI_PACKET,
+	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_MULTI_PACKET,
 	.rx_fixup = asix_rx_fixup_common,
 	.tx_fixup = asix_tx_fixup,
 	.data = FLAG_EEPROM_MAC,