| Message ID | 1349276133-26408-6-git-send-email-mporter@ti.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Headers | show |
On 10/3/2012 8:25 PM, Matt Porter wrote: > Adds PRUSS clock, registers the L3RAM pool, and registers the > platform device for uio_pruss on DA850. > > Signed-off-by: Matt Porter <mporter@ti.com> I am interested in knowing how this patch was tested. > --- > arch/arm/mach-davinci/board-da850-evm.c | 12 +++++ > arch/arm/mach-davinci/da850.c | 7 +++ > arch/arm/mach-davinci/devices-da8xx.c | 66 ++++++++++++++++++++++++++++ > arch/arm/mach-davinci/include/mach/da8xx.h | 2 + > 4 files changed, 87 insertions(+) > > diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c > index 1295e61..acc6e84 100644 > --- a/arch/arm/mach-davinci/board-da850-evm.c > +++ b/arch/arm/mach-davinci/board-da850-evm.c > @@ -29,6 +29,7 @@ > #include <linux/regulator/machine.h> > #include <linux/regulator/tps6507x.h> > #include <linux/input/tps6507x-ts.h> > +#include <linux/platform_data/uio_pruss.h> > #include <linux/spi/spi.h> > #include <linux/spi/flash.h> > #include <linux/delay.h> > @@ -42,6 +43,7 @@ > #include <mach/da8xx.h> > #include <linux/platform_data/mtd-davinci.h> > #include <mach/mux.h> > +#include <mach/sram.h> > #include <linux/platform_data/mtd-davinci-aemif.h> > #include <linux/platform_data/spi-davinci.h> I know you did not introduce the mess, but can you include a patch to fix the mixture of mach/ and linux/ includes here? mach/ includes should follow the linux/ includes. > > @@ -1253,6 +1255,10 @@ static __init int da850_wl12xx_init(void) > > #endif /* CONFIG_DA850_WL12XX */ > > +struct uio_pruss_pdata da8xx_pruss_uio_pdata = { > + .pintc_base = 0x4000, > +}; > + > #define DA850EVM_SATA_REFCLKPN_RATE (100 * 1000 * 1000) > > static __init void da850_evm_init(void) > @@ -1339,6 +1345,12 @@ static __init void da850_evm_init(void) > pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n", > ret); > > + da8xx_pruss_uio_pdata.l3ram_pool = sram_get_gen_pool(); I wonder if this platform data should still be called l3ram pool. L3RAM is OMAP terminology. May be just call it sram_pool? Also this patch should follow 6/6 to prevent build breakage. > + ret = da8xx_register_pruss_uio(&da8xx_pruss_uio_pdata); > + if (ret) > + pr_warning("pruss_uio initialization failed: %d\n", > + ret); > + > /* Handle board specific muxing for LCD here */ > ret = davinci_cfg_reg_list(da850_evm_lcdc_pins); > if (ret) > diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c > index d8d69de..7c01d31 100644 > --- a/arch/arm/mach-davinci/da850.c > +++ b/arch/arm/mach-davinci/da850.c Can you separate out board and SoC changes into different patches? > @@ -212,6 +212,12 @@ static struct clk tptc2_clk = { > .flags = ALWAYS_ENABLED, > }; > > +static struct clk pruss_clk = { > + .name = "pruss", > + .parent = &pll0_sysclk2, > + .lpsc = DA8XX_LPSC0_PRUSS, > +}; > + > static struct clk uart0_clk = { > .name = "uart0", > .parent = &pll0_sysclk2, > @@ -378,6 +384,7 @@ static struct clk_lookup da850_clks[] = { > CLK(NULL, "tptc1", &tptc1_clk), > CLK(NULL, "tpcc1", &tpcc1_clk), > CLK(NULL, "tptc2", &tptc2_clk), > + CLK(NULL, "pruss", &pruss_clk), This is actually incorrect since we should use device name rather than con_id for matching the clock. If there is just one clock that the driver needs, connection id should be NULL. Looking at the driver now, the clk_get() call seems to pass a valid device pointer. So, I wonder how you are able to look up the clock even with a NULL device name. > CLK(NULL, "uart0", &uart0_clk), > CLK(NULL, "uart1", &uart1_clk), > CLK(NULL, "uart2", &uart2_clk), > diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c > index bd2f72b..7c2e0d2 100644 > --- a/arch/arm/mach-davinci/devices-da8xx.c > +++ b/arch/arm/mach-davinci/devices-da8xx.c > @@ -518,6 +518,72 @@ void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata) > } > } > > +#define DA8XX_PRUSS_MEM_BASE 0x01C30000 In this file all base addresses are added at the top of the file. The defines are sorted in ascending order of address. If that's broken, its all my fault, but please don't add to the breakage when adding this entry :) > + > +static struct resource da8xx_pruss_resources[] = { > + { > + .start = DA8XX_PRUSS_MEM_BASE, > + .end = DA8XX_PRUSS_MEM_BASE + 0xFFFF, > + .flags = IORESOURCE_MEM, > + }, > + { > + .start = IRQ_DA8XX_EVTOUT0, > + .end = IRQ_DA8XX_EVTOUT0, > + .flags = IORESOURCE_IRQ, > + }, > + { > + .start = IRQ_DA8XX_EVTOUT1, > + .end = IRQ_DA8XX_EVTOUT1, > + .flags = IORESOURCE_IRQ, > + }, > + { > + .start = IRQ_DA8XX_EVTOUT2, > + .end = IRQ_DA8XX_EVTOUT2, > + .flags = IORESOURCE_IRQ, > + }, > + { > + .start = IRQ_DA8XX_EVTOUT3, > + .end = IRQ_DA8XX_EVTOUT3, > + .flags = IORESOURCE_IRQ, > + }, > + { > + .start = IRQ_DA8XX_EVTOUT4, > + .end = IRQ_DA8XX_EVTOUT4, > + .flags = IORESOURCE_IRQ, > + }, > + { > + .start = IRQ_DA8XX_EVTOUT5, > + .end = IRQ_DA8XX_EVTOUT5, > + .flags = IORESOURCE_IRQ, > + }, > + { > + .start = IRQ_DA8XX_EVTOUT6, > + .end = IRQ_DA8XX_EVTOUT6, > + .flags = IORESOURCE_IRQ, > + }, > + { > + .start = IRQ_DA8XX_EVTOUT7, > + .end = IRQ_DA8XX_EVTOUT7, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device da8xx_pruss_uio_dev = { > + .name = "pruss_uio", > + .id = -1, > + .num_resources = ARRAY_SIZE(da8xx_pruss_resources), > + .resource = da8xx_pruss_resources, > + .dev = { > + .coherent_dma_mask = 0xffffffff, DMA_BIT_MASK(32)? Thanks, Sekhar
On Thu, Oct 04, 2012 at 05:52:45PM +0530, Sekhar Nori wrote: > On 10/3/2012 8:25 PM, Matt Porter wrote: > > Adds PRUSS clock, registers the L3RAM pool, and registers the > > platform device for uio_pruss on DA850. > > > > Signed-off-by: Matt Porter <mporter@ti.com> > > I am interested in knowing how this patch was tested. I'll add similar test information in the commit that I mention in my other reply. Basically, I use the examples in the PRU package downloadable from ti.com. There's a PRU_memAccessL3andDDR example which will fail miserably if the uio_pruss driver SRAM resource is not configured properly. With the complete series in place, it's able to complete execution successfully, communicating via the shared sram pool. > > --- > > arch/arm/mach-davinci/board-da850-evm.c | 12 +++++ > > arch/arm/mach-davinci/da850.c | 7 +++ > > arch/arm/mach-davinci/devices-da8xx.c | 66 ++++++++++++++++++++++++++++ > > arch/arm/mach-davinci/include/mach/da8xx.h | 2 + > > 4 files changed, 87 insertions(+) > > > > diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c > > index 1295e61..acc6e84 100644 > > --- a/arch/arm/mach-davinci/board-da850-evm.c > > +++ b/arch/arm/mach-davinci/board-da850-evm.c > > @@ -29,6 +29,7 @@ > > #include <linux/regulator/machine.h> > > #include <linux/regulator/tps6507x.h> > > #include <linux/input/tps6507x-ts.h> > > +#include <linux/platform_data/uio_pruss.h> > > #include <linux/spi/spi.h> > > #include <linux/spi/flash.h> > > #include <linux/delay.h> > > @@ -42,6 +43,7 @@ > > #include <mach/da8xx.h> > > #include <linux/platform_data/mtd-davinci.h> > > #include <mach/mux.h> > > +#include <mach/sram.h> > > #include <linux/platform_data/mtd-davinci-aemif.h> > > #include <linux/platform_data/spi-davinci.h> > > I know you did not introduce the mess, but can you include a patch to > fix the mixture of mach/ and linux/ includes here? mach/ includes should > follow the linux/ includes. Ok. Yeah, I agree it's a mess there. > > @@ -1253,6 +1255,10 @@ static __init int da850_wl12xx_init(void) > > > > #endif /* CONFIG_DA850_WL12XX */ > > > > +struct uio_pruss_pdata da8xx_pruss_uio_pdata = { > > + .pintc_base = 0x4000, > > +}; > > + > > #define DA850EVM_SATA_REFCLKPN_RATE (100 * 1000 * 1000) > > > > static __init void da850_evm_init(void) > > @@ -1339,6 +1345,12 @@ static __init void da850_evm_init(void) > > pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n", > > ret); > > > > + da8xx_pruss_uio_pdata.l3ram_pool = sram_get_gen_pool(); > > I wonder if this platform data should still be called l3ram pool. L3RAM > is OMAP terminology. May be just call it sram_pool? Also this patch > should follow 6/6 to prevent build breakage. I agree, I'll change to sram_pool. I went back and forth on this because I found even the userspace PRU tools had it called L3...I think it's wise just say sram and avoid confusion. I'll move the patch too. > > + ret = da8xx_register_pruss_uio(&da8xx_pruss_uio_pdata); > > + if (ret) > > + pr_warning("pruss_uio initialization failed: %d\n", > > + ret); > > + > > /* Handle board specific muxing for LCD here */ > > ret = davinci_cfg_reg_list(da850_evm_lcdc_pins); > > if (ret) > > diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c > > index d8d69de..7c01d31 100644 > > --- a/arch/arm/mach-davinci/da850.c > > +++ b/arch/arm/mach-davinci/da850.c > > Can you separate out board and SoC changes into different patches? Ok, yes. > > @@ -212,6 +212,12 @@ static struct clk tptc2_clk = { > > .flags = ALWAYS_ENABLED, > > }; > > > > +static struct clk pruss_clk = { > > + .name = "pruss", > > + .parent = &pll0_sysclk2, > > + .lpsc = DA8XX_LPSC0_PRUSS, > > +}; > > + > > static struct clk uart0_clk = { > > .name = "uart0", > > .parent = &pll0_sysclk2, > > @@ -378,6 +384,7 @@ static struct clk_lookup da850_clks[] = { > > CLK(NULL, "tptc1", &tptc1_clk), > > CLK(NULL, "tpcc1", &tpcc1_clk), > > CLK(NULL, "tptc2", &tptc2_clk), > > + CLK(NULL, "pruss", &pruss_clk), > > This is actually incorrect since we should use device name rather than > con_id for matching the clock. If there is just one clock that the > driver needs, connection id should be NULL. Looking at the driver now, > the clk_get() call seems to pass a valid device pointer. So, I wonder > how you are able to look up the clock even with a NULL device name. Hrm, I'll look into this. This part was a not looked at closely, just a quick copy/paste/modify and worked as tested with the PRU examples so I didn't look further. I'll look again let you know why it actually works. I'm guessing I got lucky here, and should be a simple fix. > > CLK(NULL, "uart0", &uart0_clk), > > CLK(NULL, "uart1", &uart1_clk), > > CLK(NULL, "uart2", &uart2_clk), > > diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c > > index bd2f72b..7c2e0d2 100644 > > --- a/arch/arm/mach-davinci/devices-da8xx.c > > +++ b/arch/arm/mach-davinci/devices-da8xx.c > > @@ -518,6 +518,72 @@ void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata) > > } > > } > > > > +#define DA8XX_PRUSS_MEM_BASE 0x01C30000 > > In this file all base addresses are added at the top of the file. The > defines are sorted in ascending order of address. If that's broken, its > all my fault, but please don't add to the breakage when adding this entry :) Ok :) Will fix. > > + > > +static struct resource da8xx_pruss_resources[] = { > > + { > > + .start = DA8XX_PRUSS_MEM_BASE, > > + .end = DA8XX_PRUSS_MEM_BASE + 0xFFFF, > > + .flags = IORESOURCE_MEM, > > + }, > > + { > > + .start = IRQ_DA8XX_EVTOUT0, > > + .end = IRQ_DA8XX_EVTOUT0, > > + .flags = IORESOURCE_IRQ, > > + }, > > + { > > + .start = IRQ_DA8XX_EVTOUT1, > > + .end = IRQ_DA8XX_EVTOUT1, > > + .flags = IORESOURCE_IRQ, > > + }, > > + { > > + .start = IRQ_DA8XX_EVTOUT2, > > + .end = IRQ_DA8XX_EVTOUT2, > > + .flags = IORESOURCE_IRQ, > > + }, > > + { > > + .start = IRQ_DA8XX_EVTOUT3, > > + .end = IRQ_DA8XX_EVTOUT3, > > + .flags = IORESOURCE_IRQ, > > + }, > > + { > > + .start = IRQ_DA8XX_EVTOUT4, > > + .end = IRQ_DA8XX_EVTOUT4, > > + .flags = IORESOURCE_IRQ, > > + }, > > + { > > + .start = IRQ_DA8XX_EVTOUT5, > > + .end = IRQ_DA8XX_EVTOUT5, > > + .flags = IORESOURCE_IRQ, > > + }, > > + { > > + .start = IRQ_DA8XX_EVTOUT6, > > + .end = IRQ_DA8XX_EVTOUT6, > > + .flags = IORESOURCE_IRQ, > > + }, > > + { > > + .start = IRQ_DA8XX_EVTOUT7, > > + .end = IRQ_DA8XX_EVTOUT7, > > + .flags = IORESOURCE_IRQ, > > + }, > > +}; > > + > > +static struct platform_device da8xx_pruss_uio_dev = { > > + .name = "pruss_uio", > > + .id = -1, > > + .num_resources = ARRAY_SIZE(da8xx_pruss_resources), > > + .resource = da8xx_pruss_resources, > > + .dev = { > > + .coherent_dma_mask = 0xffffffff, > > DMA_BIT_MASK(32)? Yeah, more copy/paste/modify stuff. I'll fix that. -Matt
On Thu, Oct 04, 2012 at 05:52:45PM +0530, Sekhar Nori wrote: > On 10/3/2012 8:25 PM, Matt Porter wrote: > > +static struct clk pruss_clk = { > > + .name = "pruss", > > + .parent = &pll0_sysclk2, > > + .lpsc = DA8XX_LPSC0_PRUSS, > > +}; > > + > > static struct clk uart0_clk = { > > .name = "uart0", > > .parent = &pll0_sysclk2, > > @@ -378,6 +384,7 @@ static struct clk_lookup da850_clks[] = { > > CLK(NULL, "tptc1", &tptc1_clk), > > CLK(NULL, "tpcc1", &tpcc1_clk), > > CLK(NULL, "tptc2", &tptc2_clk), > > + CLK(NULL, "pruss", &pruss_clk), > > This is actually incorrect since we should use device name rather than > con_id for matching the clock. If there is just one clock that the > driver needs, connection id should be NULL. Looking at the driver now, > the clk_get() call seems to pass a valid device pointer. So, I wonder > how you are able to look up the clock even with a NULL device name. I doublechecked the clk_get() find implentation to confirm that I indeed did get lucky here. Since pruss has only one instance and the clk_find() implementation looks for the best found match, it's able to find the clock just by the con_id, though it's not the "best possible" match in the find implementation...it's the "best found" match.. As you noted, this is incorrect though for a clock expected to be used from a driver context so I will address this in the update. -Matt
On 10/4/2012 10:05 PM, Matt Porter wrote: > On Thu, Oct 04, 2012 at 05:52:45PM +0530, Sekhar Nori wrote: >> On 10/3/2012 8:25 PM, Matt Porter wrote: >>> +static struct clk pruss_clk = { >>> + .name = "pruss", >>> + .parent = &pll0_sysclk2, >>> + .lpsc = DA8XX_LPSC0_PRUSS, >>> +}; >>> + >>> static struct clk uart0_clk = { >>> .name = "uart0", >>> .parent = &pll0_sysclk2, >>> @@ -378,6 +384,7 @@ static struct clk_lookup da850_clks[] = { >>> CLK(NULL, "tptc1", &tptc1_clk), >>> CLK(NULL, "tpcc1", &tpcc1_clk), >>> CLK(NULL, "tptc2", &tptc2_clk), >>> + CLK(NULL, "pruss", &pruss_clk), >> >> This is actually incorrect since we should use device name rather than >> con_id for matching the clock. If there is just one clock that the >> driver needs, connection id should be NULL. Looking at the driver now, >> the clk_get() call seems to pass a valid device pointer. So, I wonder >> how you are able to look up the clock even with a NULL device name. > > I doublechecked the clk_get() find implentation to confirm that I indeed > did get lucky here. Since pruss has only one instance and the clk_find() > implementation looks for the best found match, it's able to find the > clock just by the con_id, though it's not the "best possible" match in > the find implementation...it's the "best found" match.. As you noted, > this is incorrect though for a clock expected to be used from a driver > context so I will address this in the update. Thanks for debugging and clarifying. Regards, Sekhar
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 1295e61..acc6e84 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -29,6 +29,7 @@ #include <linux/regulator/machine.h> #include <linux/regulator/tps6507x.h> #include <linux/input/tps6507x-ts.h> +#include <linux/platform_data/uio_pruss.h> #include <linux/spi/spi.h> #include <linux/spi/flash.h> #include <linux/delay.h> @@ -42,6 +43,7 @@ #include <mach/da8xx.h> #include <linux/platform_data/mtd-davinci.h> #include <mach/mux.h> +#include <mach/sram.h> #include <linux/platform_data/mtd-davinci-aemif.h> #include <linux/platform_data/spi-davinci.h> @@ -1253,6 +1255,10 @@ static __init int da850_wl12xx_init(void) #endif /* CONFIG_DA850_WL12XX */ +struct uio_pruss_pdata da8xx_pruss_uio_pdata = { + .pintc_base = 0x4000, +}; + #define DA850EVM_SATA_REFCLKPN_RATE (100 * 1000 * 1000) static __init void da850_evm_init(void) @@ -1339,6 +1345,12 @@ static __init void da850_evm_init(void) pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n", ret); + da8xx_pruss_uio_pdata.l3ram_pool = sram_get_gen_pool(); + ret = da8xx_register_pruss_uio(&da8xx_pruss_uio_pdata); + if (ret) + pr_warning("pruss_uio initialization failed: %d\n", + ret); + /* Handle board specific muxing for LCD here */ ret = davinci_cfg_reg_list(da850_evm_lcdc_pins); if (ret) diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index d8d69de..7c01d31 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -212,6 +212,12 @@ static struct clk tptc2_clk = { .flags = ALWAYS_ENABLED, }; +static struct clk pruss_clk = { + .name = "pruss", + .parent = &pll0_sysclk2, + .lpsc = DA8XX_LPSC0_PRUSS, +}; + static struct clk uart0_clk = { .name = "uart0", .parent = &pll0_sysclk2, @@ -378,6 +384,7 @@ static struct clk_lookup da850_clks[] = { CLK(NULL, "tptc1", &tptc1_clk), CLK(NULL, "tpcc1", &tpcc1_clk), CLK(NULL, "tptc2", &tptc2_clk), + CLK(NULL, "pruss", &pruss_clk), CLK(NULL, "uart0", &uart0_clk), CLK(NULL, "uart1", &uart1_clk), CLK(NULL, "uart2", &uart2_clk), diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c index bd2f72b..7c2e0d2 100644 --- a/arch/arm/mach-davinci/devices-da8xx.c +++ b/arch/arm/mach-davinci/devices-da8xx.c @@ -518,6 +518,72 @@ void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata) } } +#define DA8XX_PRUSS_MEM_BASE 0x01C30000 + +static struct resource da8xx_pruss_resources[] = { + { + .start = DA8XX_PRUSS_MEM_BASE, + .end = DA8XX_PRUSS_MEM_BASE + 0xFFFF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_DA8XX_EVTOUT0, + .end = IRQ_DA8XX_EVTOUT0, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_DA8XX_EVTOUT1, + .end = IRQ_DA8XX_EVTOUT1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_DA8XX_EVTOUT2, + .end = IRQ_DA8XX_EVTOUT2, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_DA8XX_EVTOUT3, + .end = IRQ_DA8XX_EVTOUT3, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_DA8XX_EVTOUT4, + .end = IRQ_DA8XX_EVTOUT4, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_DA8XX_EVTOUT5, + .end = IRQ_DA8XX_EVTOUT5, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_DA8XX_EVTOUT6, + .end = IRQ_DA8XX_EVTOUT6, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_DA8XX_EVTOUT7, + .end = IRQ_DA8XX_EVTOUT7, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device da8xx_pruss_uio_dev = { + .name = "pruss_uio", + .id = -1, + .num_resources = ARRAY_SIZE(da8xx_pruss_resources), + .resource = da8xx_pruss_resources, + .dev = { + .coherent_dma_mask = 0xffffffff, + } +}; + +int __init da8xx_register_pruss_uio(struct uio_pruss_pdata *config) +{ + da8xx_pruss_uio_dev.dev.platform_data = config; + return platform_device_register(&da8xx_pruss_uio_dev); +} + static const struct display_panel disp_panel = { QVGA, 16, diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h index 20553cf..138e618 100644 --- a/arch/arm/mach-davinci/include/mach/da8xx.h +++ b/arch/arm/mach-davinci/include/mach/da8xx.h @@ -25,6 +25,7 @@ #include <linux/platform_data/mmc-davinci.h> #include <linux/platform_data/usb-davinci.h> #include <linux/platform_data/spi-davinci.h> +#include <linux/platform_data/uio_pruss.h> extern void __iomem *da8xx_syscfg0_base; extern void __iomem *da8xx_syscfg1_base; @@ -83,6 +84,7 @@ int da8xx_register_watchdog(void); int da8xx_register_usb20(unsigned mA, unsigned potpgt); int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata); int da8xx_register_emac(void); +int da8xx_register_pruss_uio(struct uio_pruss_pdata *config); int da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata); int da8xx_register_mmcsd0(struct davinci_mmc_config *config); int da850_register_mmcsd1(struct davinci_mmc_config *config);
Adds PRUSS clock, registers the L3RAM pool, and registers the platform device for uio_pruss on DA850. Signed-off-by: Matt Porter <mporter@ti.com> --- arch/arm/mach-davinci/board-da850-evm.c | 12 +++++ arch/arm/mach-davinci/da850.c | 7 +++ arch/arm/mach-davinci/devices-da8xx.c | 66 ++++++++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/da8xx.h | 2 + 4 files changed, 87 insertions(+)