diff mbox

[1/4] mtd: nand: omap2: Update nerrors using ecc.strength

Message ID 1349274589-11389-2-git-send-email-avinashphilip@ti.com (mailing list archive)
State New, archived
Headers show

Commit Message

avinash philip Oct. 3, 2012, 2:29 p.m. UTC
Update number of errors using nand ecc strength.
Also add macro definitions BCH8_ERROR_MAX & BCH4_ERROR_MAX

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
---
:100644 100644 5b31386... af511a9... M	drivers/mtd/nand/omap2.c
 drivers/mtd/nand/omap2.c |   12 ++++++++----
 1 files changed, 8 insertions(+), 4 deletions(-)

Comments

Peter Korsgaard Oct. 15, 2012, 6:56 p.m. UTC | #1
>>>>> Philip, Avinash <avinashphilip@ti.com> writes:

 > Update number of errors using nand ecc strength.
 > Also add macro definitions BCH8_ERROR_MAX & BCH4_ERROR_MAX

 > Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
 > ---
 > :100644 100644 5b31386... af511a9... M	drivers/mtd/nand/omap2.c
 >  drivers/mtd/nand/omap2.c |   12 ++++++++----
 >  1 files changed, 8 insertions(+), 4 deletions(-)

 > diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
 > index 5b31386..af511a9 100644
 > --- a/drivers/mtd/nand/omap2.c
 > +++ b/drivers/mtd/nand/omap2.c
 > @@ -111,6 +111,9 @@
 >  #define	ECCCLEAR			0x100
 >  #define	ECC1				0x1
 
 > +#define BCH8_MAX_ERROR		8	/* upto 8 bit coorectable */
 > +#define BCH4_MAX_ERROR		4	/* upto 4 bit correctable */

First 'correctable' misspelled.

I don't personally think these defines improve readability very much
compared to to just using 4/8, though.
avinash philip Oct. 23, 2012, 10:17 a.m. UTC | #2
On Tue, Oct 16, 2012 at 00:26:40, Peter Korsgaard wrote:
> >>>>> Philip, Avinash <avinashphilip@ti.com> writes:
> 
>  > Update number of errors using nand ecc strength.
>  > Also add macro definitions BCH8_ERROR_MAX & BCH4_ERROR_MAX
> 
>  > Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
>  > ---
>  > :100644 100644 5b31386... af511a9... M	drivers/mtd/nand/omap2.c
>  >  drivers/mtd/nand/omap2.c |   12 ++++++++----
>  >  1 files changed, 8 insertions(+), 4 deletions(-)
> 
>  > diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
>  > index 5b31386..af511a9 100644
>  > --- a/drivers/mtd/nand/omap2.c
>  > +++ b/drivers/mtd/nand/omap2.c
>  > @@ -111,6 +111,9 @@
>  >  #define	ECCCLEAR			0x100
>  >  #define	ECC1				0x1
>  
>  > +#define BCH8_MAX_ERROR		8	/* upto 8 bit coorectable */
>  > +#define BCH4_MAX_ERROR		4	/* upto 4 bit correctable */
> 
> First 'correctable' misspelled.

I will correct it

> 
> I don't personally think these defines improve readability very much
> compared to to just using 4/8, though.

Thought of removing magic numbers & provide information also.

Thanks
Avinash

> 
> -- 
> Bye, Peter Korsgaard
>
diff mbox

Patch

diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index 5b31386..af511a9 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -111,6 +111,9 @@ 
 #define	ECCCLEAR			0x100
 #define	ECC1				0x1
 
+#define BCH8_MAX_ERROR		8	/* upto 8 bit coorectable */
+#define BCH4_MAX_ERROR		4	/* upto 4 bit correctable */
+
 /* oob info generated runtime depending on ecc algorithm and layout selected */
 static struct nand_ecclayout omap_oobinfo;
 /* Define some generic bad / good block scan pattern which are used
@@ -1034,7 +1037,7 @@  static void omap3_enable_hwecc_bch(struct mtd_info *mtd, int mode)
 						   mtd);
 	struct nand_chip *chip = mtd->priv;
 
-	nerrors = (info->nand.ecc.bytes == 13) ? 8 : 4;
+	nerrors = info->nand.ecc.strength;
 	dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0;
 	/*
 	 * Program GPMC to perform correction on one 512-byte sector at a time.
@@ -1129,13 +1132,14 @@  static int omap3_init_bch(struct mtd_info *mtd, int ecc_opt)
 	struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
 						   mtd);
 #ifdef CONFIG_MTD_NAND_OMAP_BCH8
-	const int hw_errors = 8;
+	const int hw_errors = BCH8_MAX_ERROR;
 #else
-	const int hw_errors = 4;
+	const int hw_errors = BCH4_MAX_ERROR;
 #endif
 	info->bch = NULL;
 
-	max_errors = (ecc_opt == OMAP_ECC_BCH8_CODE_HW) ? 8 : 4;
+	max_errors = (ecc_opt == OMAP_ECC_BCH8_CODE_HW) ?
+		BCH8_MAX_ERROR : BCH4_MAX_ERROR;
 	if (max_errors != hw_errors) {
 		pr_err("cannot configure %d-bit BCH ecc, only %d-bit supported",
 		       max_errors, hw_errors);