@@ -65,11 +65,21 @@
#define OTGSC_ASVIS BIT(18)
#define OTGSC_BSVIS BIT(19)
#define OTGSC_BSEIS BIT(20)
+#define OTGSC_1MSIS BIT(21)
+#define OTGSC_DPIS BIT(22)
#define OTGSC_IDIE BIT(24)
#define OTGSC_AVVIE BIT(25)
#define OTGSC_ASVIE BIT(26)
#define OTGSC_BSVIE BIT(27)
#define OTGSC_BSEIE BIT(28)
+#define OTGSC_1MSIE BIT(29)
+#define OTGSC_DPIE BIT(30)
+#define OTGSC_INT_EN_BITS (OTGSC_IDIE | OTGSC_AVVIE | OTGSC_ASVIE \
+ | OTGSC_BSVIE | OTGSC_BSEIE | OTGSC_1MSIE \
+ | OTGSC_DPIE)
+#define OTGSC_INT_STATUS_BITS (OTGSC_IDIS | OTGSC_AVVIS | OTGSC_ASVIS \
+ | OTGSC_BSVIS | OTGSC_BSEIS | OTGSC_1MSIS \
+ | OTGSC_DPIS)
/* USBMODE */
#define USBMODE_CM (0x03UL << 0)
@@ -130,6 +130,7 @@ struct hw_bank {
* @transceiver: pointer to USB PHY, if any
* @hcd: pointer to usb_hcd for ehci host driver
* @otg: for otg support
+ * @events: events for otg, and handled at ci_role_work
*/
struct ci13xxx {
struct device *dev;
@@ -140,6 +141,7 @@ struct ci13xxx {
enum ci_role role;
bool is_otg;
struct work_struct work;
+ struct delayed_work dwork;
struct workqueue_struct *wq;
struct dma_pool *qh_pool;
@@ -165,7 +167,9 @@ struct ci13xxx {
bool global_phy;
struct usb_phy *transceiver;
struct usb_hcd *hcd;
- struct usb_otg otg;
+ struct usb_otg otg;
+ bool id_event;
+ bool b_sess_valid_event;
};
static inline struct ci_role_driver *ci_role(struct ci13xxx *ci)
@@ -314,4 +318,6 @@ int hw_port_test_set(struct ci13xxx *ci, u8 mode);
u8 hw_port_test_get(struct ci13xxx *ci);
+void ci_handle_vbus_change(struct ci13xxx *ci);
+
#endif /* __DRIVERS_USB_CHIPIDEA_CI_H */
@@ -73,6 +73,7 @@
#include "bits.h"
#include "host.h"
#include "debug.h"
+#include "otg.h"
/* Controller register map */
static uintptr_t ci_regs_nolpm[] = {
@@ -199,6 +200,14 @@ static int hw_device_init(struct ci13xxx *ci, void __iomem *base)
if (ci->hw_ep_max > ENDPT_MAX)
return -ENODEV;
+ /* Disable all interrupts bits */
+ hw_write(ci, OP_USBINTR, 0xffffffff, 0);
+ ci_disable_otg_interrupt(ci, OTGSC_INT_EN_BITS);
+
+ /* Clear all interrupts status bits*/
+ hw_write(ci, OP_USBSTS, 0xffffffff, 0xffffffff);
+ ci_clear_otg_interrupt(ci, OTGSC_INT_STATUS_BITS);
+
dev_dbg(ci->dev, "ChipIdea HDRC found, lpm: %d; cap: %p op: %p\n",
ci->hw_bank.lpm, ci->hw_bank.cap, ci->hw_bank.op);
@@ -265,24 +274,124 @@ static enum ci_role ci_otg_role(struct ci13xxx *ci)
}
/**
- * ci_role_work - perform role changing based on ID pin
- * @work: work struct
+ * hw_wait_reg: wait the register value
+ *
+ * Sometimes, it needs to wait register value before going on.
+ * Eg, when switch to device mode, the vbus value should be lower
+ * than OTGSC_BSV before connects to host.
+ *
+ * @ci: the controller
+ * @reg: register index
+ * @mask: mast bit
+ * @value: the bit value to wait
+ * @timeout: timeout to indicate an error
+ *
+ * This function returns an error code if timeout
*/
-static void ci_role_work(struct work_struct *work)
+static int hw_wait_reg(struct ci13xxx *ci, enum ci13xxx_regs reg, u32 mask,
+ u32 value, unsigned long timeout)
+{
+ unsigned long elapse = jiffies + timeout;
+
+ while (hw_read(ci, reg, mask) != value) {
+ if (time_after(jiffies, elapse)) {
+ dev_err(ci->dev, "timeout waiting for %08x in %d\n",
+ mask, reg);
+ return -ETIMEDOUT;
+ }
+ msleep(20);
+ }
+
+ return 0;
+}
+
+#define CI_VBUS_STABLE_TIMEOUT 500
+static void ci_handle_id_switch(struct ci13xxx *ci)
{
- struct ci13xxx *ci = container_of(work, struct ci13xxx, work);
enum ci_role role = ci_otg_role(ci);
if (role != ci->role) {
dev_dbg(ci->dev, "switching from %s to %s\n",
ci_role(ci)->name, ci->roles[role]->name);
- ci_role_stop(ci);
- ci_role_start(ci, role);
- enable_irq(ci->irq);
+ /* 1. Finish the current role */
+ if (ci->role == CI_ROLE_GADGET) {
+ usb_gadget_vbus_disconnect(&ci->gadget);
+ /* host doesn't care B_SESSION_VALID event */
+ ci_clear_otg_interrupt(ci, OTGSC_BSVIS);
+ ci_disable_otg_interrupt(ci, OTGSC_BSVIE);
+ ci->role = CI_ROLE_END;
+ /* reset controller */
+ hw_device_reset(ci, USBMODE_CM_IDLE);
+ } else if (ci->role == CI_ROLE_HOST) {
+ ci_role_stop(ci);
+ /* reset controller */
+ hw_device_reset(ci, USBMODE_CM_IDLE);
+ }
+
+ /* 2. Turn on/off vbus according to coming role */
+ if (ci_otg_role(ci) == CI_ROLE_GADGET) {
+ otg_set_vbus(&ci->otg, false);
+ /* wait vbus lower than OTGSC_BSV */
+ hw_wait_reg(ci, OP_OTGSC, OTGSC_BSV, 0,
+ CI_VBUS_STABLE_TIMEOUT);
+ } else if (ci_otg_role(ci) == CI_ROLE_HOST) {
+ otg_set_vbus(&ci->otg, true);
+ /* wait vbus higher than OTGSC_AVV */
+ hw_wait_reg(ci, OP_OTGSC, OTGSC_AVV, OTGSC_AVV,
+ CI_VBUS_STABLE_TIMEOUT);
+ }
+
+ /* 3. Begin the new role */
+ if (ci_otg_role(ci) == CI_ROLE_GADGET) {
+ ci->role = role;
+ ci_clear_otg_interrupt(ci, OTGSC_BSVIS);
+ ci_enable_otg_interrupt(ci, OTGSC_BSVIE);
+ } else if (ci_otg_role(ci) == CI_ROLE_HOST) {
+ ci_role_start(ci, role);
+ }
}
}
+void ci_handle_vbus_change(struct ci13xxx *ci)
+{
+ u32 otgsc = hw_read(ci, OP_OTGSC, ~0);
+
+ if (otgsc & OTGSC_BSV)
+ usb_gadget_vbus_connect(&ci->gadget);
+ else
+ usb_gadget_vbus_disconnect(&ci->gadget);
+}
+
+/**
+ * ci_otg_work - perform otg (vbus/id) event handle
+ * @work: work struct
+ */
+static void ci_otg_work(struct work_struct *work)
+{
+ struct ci13xxx *ci = container_of(work, struct ci13xxx, work);
+
+ if (ci->id_event) {
+ ci->id_event = false;
+ ci_handle_id_switch(ci);
+ } else if (ci->b_sess_valid_event) {
+ ci->b_sess_valid_event = false;
+ ci_handle_vbus_change(ci);
+ } else
+ dev_err(ci->dev, "unexpected event occurs at %s\n", __func__);
+
+ enable_irq(ci->irq);
+}
+
+static void ci_delayed_work(struct work_struct *work)
+{
+ struct delayed_work *dwork = to_delayed_work(work);
+ struct ci13xxx *ci = container_of(dwork, struct ci13xxx, dwork);
+
+ otg_set_vbus(&ci->otg, true);
+
+}
+
static ssize_t show_role(struct device *dev, struct device_attribute *attr,
char *buf)
{
@@ -321,19 +430,36 @@ static irqreturn_t ci_irq(int irq, void *data)
irqreturn_t ret = IRQ_NONE;
u32 otgsc = 0;
- if (ci->is_otg)
- otgsc = hw_read(ci, OP_OTGSC, ~0);
+ otgsc = hw_read(ci, OP_OTGSC, ~0);
- if (ci->role != CI_ROLE_END)
- ret = ci_role(ci)->irq(ci);
+ /*
+ * Handle id change interrupt, it indicates device/host function
+ * switch.
+ */
+ if (ci->is_otg && (otgsc & OTGSC_IDIE) && (otgsc & OTGSC_IDIS)) {
+ ci->id_event = true;
+ ci_clear_otg_interrupt(ci, OTGSC_IDIS);
+ disable_irq_nosync(ci->irq);
+ queue_work(ci->wq, &ci->work);
+ return IRQ_HANDLED;
+ }
- if (ci->is_otg && (otgsc & OTGSC_IDIS)) {
- hw_write(ci, OP_OTGSC, OTGSC_IDIS, OTGSC_IDIS);
+ /*
+ * Handle vbus change interrupt, it indicates device connection
+ * and disconnection events.
+ */
+ if ((otgsc & OTGSC_BSVIE) && (otgsc & OTGSC_BSVIS)) {
+ ci->b_sess_valid_event = true;
+ ci_clear_otg_interrupt(ci, OTGSC_BSVIS);
disable_irq_nosync(ci->irq);
queue_work(ci->wq, &ci->work);
- ret = IRQ_HANDLED;
+ return IRQ_HANDLED;
}
+ /* Handle device/host interrupt */
+ if (ci->role != CI_ROLE_END)
+ ret = ci_role(ci)->irq(ci);
+
return ret;
}
@@ -398,6 +524,7 @@ static int ci_hdrc_probe(struct platform_device *pdev)
struct resource *res;
void __iomem *base;
int ret;
+ u32 otgsc;
if (!dev->platform_data) {
dev_err(dev, "platform data missing\n");
@@ -443,7 +570,8 @@ static int ci_hdrc_probe(struct platform_device *pdev)
return -ENODEV;
}
- INIT_WORK(&ci->work, ci_role_work);
+ INIT_WORK(&ci->work, ci_otg_work);
+ INIT_DELAYED_WORK(&ci->dwork, ci_delayed_work);
ci->wq = create_singlethread_workqueue("ci_otg");
if (!ci->wq) {
dev_err(dev, "can't create workqueue\n");
@@ -466,7 +594,10 @@ static int ci_hdrc_probe(struct platform_device *pdev)
}
if (ci->roles[CI_ROLE_HOST] && ci->roles[CI_ROLE_GADGET]) {
+ dev_dbg(dev, "support otg\n");
ci->is_otg = true;
+ /* if otg is supported, create struct usb_otg */
+ ci_hdrc_otg_init(ci);
/* ID pin needs 1ms debouce time, we delay 2ms for safe */
mdelay(2);
ci->role = ci_otg_role(ci);
@@ -483,6 +614,17 @@ static int ci_hdrc_probe(struct platform_device *pdev)
goto rm_wq;
}
+ otgsc = hw_read(ci, OP_OTGSC, ~0);
+ /*
+ * if it is device mode:
+ * - Enable vbus detect
+ * - If it has already connected to host, notify udc
+ */
+ if (ci->role == CI_ROLE_GADGET) {
+ ci_enable_otg_interrupt(ci, OTGSC_BSVIE);
+ ci_handle_vbus_change(ci);
+ }
+
platform_set_drvdata(pdev, ci);
ret = request_irq(ci->irq, ci_irq, IRQF_SHARED, ci->platdata->name,
ci);
@@ -493,8 +635,9 @@ static int ci_hdrc_probe(struct platform_device *pdev)
if (ret)
goto rm_attr;
- if (ci->is_otg)
- hw_write(ci, OP_OTGSC, OTGSC_IDIE, OTGSC_IDIE);
+ /* Handle the situation that usb device at the MicroB to A cable */
+ if (ci->is_otg && !(otgsc & OTGSC_ID))
+ queue_delayed_work(ci->wq, &ci->dwork, msecs_to_jiffies(500));
return ret;
@@ -10,21 +10,28 @@
* published by the Free Software Foundation.
*/
-#include <linux/platform_device.h>
-#include <linux/module.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/usb/gadget.h>
#include <linux/usb/otg.h>
+#include <linux/usb/gadget.h>
#include <linux/usb/chipidea.h>
#include "ci.h"
-#include "udc.h"
#include "bits.h"
-#include "host.h"
-#include "debug.h"
+
+void ci_clear_otg_interrupt(struct ci13xxx *ci, u32 bits)
+{
+ /* Only clear request bits */
+ hw_write(ci, OP_OTGSC, OTGSC_INT_STATUS_BITS, bits);
+}
+
+void ci_enable_otg_interrupt(struct ci13xxx *ci, u32 bits)
+{
+ hw_write(ci, OP_OTGSC, bits, bits);
+}
+
+void ci_disable_otg_interrupt(struct ci13xxx *ci, u32 bits)
+{
+ hw_write(ci, OP_OTGSC, bits, 0);
+}
static int ci_otg_set_peripheral(struct usb_otg *otg,
struct usb_gadget *periph)
@@ -55,6 +62,7 @@ int ci_hdrc_otg_init(struct ci13xxx *ci)
ci->otg.set_host = ci_otg_set_host;
if (!IS_ERR_OR_NULL(ci->transceiver))
ci->transceiver->otg = &ci->otg;
+ ci_enable_otg_interrupt(ci, OTGSC_IDIE);
return 0;
}
@@ -2,5 +2,8 @@
#define __DRIVERS_USB_CHIPIDEA_OTG_H
int ci_hdrc_otg_init(struct ci13xxx *ci);
+void ci_clear_otg_interrupt(struct ci13xxx *ci, u32 bits);
+void ci_enable_otg_interrupt(struct ci13xxx *ci, u32 bits);
+void ci_disable_otg_interrupt(struct ci13xxx *ci, u32 bits);
#endif /* __DRIVERS_USB_CHIPIDEA_OTG_H */
@@ -1371,6 +1371,7 @@ static int ci13xxx_vbus_session(struct usb_gadget *_gadget, int is_active)
pm_runtime_get_sync(&_gadget->dev);
hw_device_reset(ci, USBMODE_CM_DC);
hw_device_state(ci, ci->ep0out->qh.dma);
+ dev_dbg(ci->dev, "Connected to host\n");
} else {
hw_device_state(ci, 0);
if (ci->platdata->notify_event)
@@ -1378,6 +1379,7 @@ static int ci13xxx_vbus_session(struct usb_gadget *_gadget, int is_active)
CI13XXX_CONTROLLER_STOPPED_EVENT);
_gadget_stop_activity(&ci->gadget);
pm_runtime_put_sync(&_gadget->dev);
+ dev_dbg(ci->dev, "disconnected from host\n");
}
}
The main design flow is the same with msm otg driver, that is the id and vbus interrupt are handled at core driver, others are handled by individual drivers. - At former design, when switch usb role from device->host, it will call udc_stop, it will remove the gadget driver, so when switch role from host->device, it can't add gadget driver any more. At new design, when role switch occurs, the gadget just calls usb_gadget_vbus_disconnect/usb_gadget_vbus_connect as well as reset controller, it will not free any device/gadget structure - Add vbus connect and disconnect to core interrupt handler, it can notify udc driver by calling usb_gadget_vbus_disconnect /usb_gadget_vbus_connect. Signed-off-by: Peter Chen <peter.chen@freescale.com> --- Changes for v4: - Change the otg event flag from the bitmask to bool flag - Add some otg helper functions - Move some hardware init to hw_device_init - Move the otg init to one block Changes for v3: - Add prefix CI_ for ID and B_SESS_VALID - Use new API hw_wait_reg which is alexander sugguested to wait vbus voltage stable drivers/usb/chipidea/bits.h | 10 +++ drivers/usb/chipidea/ci.h | 8 ++- drivers/usb/chipidea/core.c | 177 ++++++++++++++++++++++++++++++++++++++---- drivers/usb/chipidea/otg.c | 28 +++++--- drivers/usb/chipidea/otg.h | 3 + drivers/usb/chipidea/udc.c | 2 + 6 files changed, 200 insertions(+), 28 deletions(-)