| Message ID | 1355326422-12357-1-git-send-email-matthias.bgg@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Matthias, On 12/12/2012 04:33 PM, Matthias Brugger wrote: > This patch is a follow-up patch for Javier Martinez effort adding initial > device tree support to IGEP technology devices. [1] > > It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards. > > [1] http://www.spinics.net/lists/linux-omap/msg83409.html > > Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> > --- > arch/arm/boot/dts/omap3-igep.dtsi | 24 ++++++++++++++++++++++++ > 1 file changed, 24 insertions(+) > > diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi > index 125fe00..c02e3c0 100644 > --- a/arch/arm/boot/dts/omap3-igep.dtsi > +++ b/arch/arm/boot/dts/omap3-igep.dtsi > @@ -27,6 +27,20 @@ > }; > > &omap3_pmx_core { > + uart1_pins: pinmux_uart1_pins { > + pinctrl-single,pins = < > + 0x152 0x100 /* uart1_rx.uart1_rx INPUT | MODE0 */ > + 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | MODE0 */ > + >; > + }; > + > + uart2_pins: pinmux_uart2_pins { > + pinctrl-single,pins = < > + 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | MODE0 */ > + 0x148 0 /* uart2_tx.uart2_tx OUTPUT | MODE0 */ > + >; > + }; > + > uart3_pins: pinmux_uart3_pins { > pinctrl-single,pins = < > 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | MODE0 */ > @@ -77,6 +91,16 @@ > status = "disabled"; > }; > > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart1_pins>; > +}; > + > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart2_pins>; > +}; > + > &uart3 { > pinctrl-names = "default"; > pinctrl-0 = <&uart3_pins>; > That looks good to me. I'll apply it on top of javier's series for 3.9. Thanks, Benoit -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Benoit, 2012/12/12 Benoit Cousson <b-cousson@ti.com>: > Hi Matthias, > > On 12/12/2012 04:33 PM, Matthias Brugger wrote: >> This patch is a follow-up patch for Javier Martinez effort adding initial >> device tree support to IGEP technology devices. [1] >> >> It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards. >> >> [1] http://www.spinics.net/lists/linux-omap/msg83409.html >> >> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> >> --- >> arch/arm/boot/dts/omap3-igep.dtsi | 24 ++++++++++++++++++++++++ >> 1 file changed, 24 insertions(+) >> >> diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi >> index 125fe00..c02e3c0 100644 >> --- a/arch/arm/boot/dts/omap3-igep.dtsi >> +++ b/arch/arm/boot/dts/omap3-igep.dtsi >> @@ -27,6 +27,20 @@ >> }; >> >> &omap3_pmx_core { >> + uart1_pins: pinmux_uart1_pins { >> + pinctrl-single,pins = < >> + 0x152 0x100 /* uart1_rx.uart1_rx INPUT | MODE0 */ >> + 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | MODE0 */ >> + >; >> + }; >> + >> + uart2_pins: pinmux_uart2_pins { >> + pinctrl-single,pins = < >> + 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | MODE0 */ >> + 0x148 0 /* uart2_tx.uart2_tx OUTPUT | MODE0 */ >> + >; >> + }; >> + >> uart3_pins: pinmux_uart3_pins { >> pinctrl-single,pins = < >> 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | MODE0 */ >> @@ -77,6 +91,16 @@ >> status = "disabled"; >> }; >> >> +&uart1 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart1_pins>; >> +}; >> + >> +&uart2 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart2_pins>; >> +}; >> + >> &uart3 { >> pinctrl-names = "default"; >> pinctrl-0 = <&uart3_pins>; >> > > That looks good to me. I'll apply it on top of javier's series for 3.9. Can you pin-point me to the repository where this patches are in right now? I tried to figure it out these days, but didn't found where to clone the repository from. Thanks, Matthias > > Thanks, > Benoit >
2013/1/26 Javier Martinez Canillas <martinez.javier@gmail.com>: > On Sat, Jan 26, 2013 at 4:16 PM, Matthias Brugger <matthias.bgg@gmail.com> > wrote: >> Hi Benoit, >> >> 2012/12/12 Benoit Cousson <b-cousson@ti.com>: >>> Hi Matthias, >>> >>> On 12/12/2012 04:33 PM, Matthias Brugger wrote: >>>> This patch is a follow-up patch for Javier Martinez effort adding >>>> initial >>>> device tree support to IGEP technology devices. [1] >>>> >>>> It adds uart1 and uart2 bindings to the generic dtsi for the IGEP >>>> boards. >>>> >>>> [1] http://www.spinics.net/lists/linux-omap/msg83409.html >>>> >>>> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> >>>> --- >>>> arch/arm/boot/dts/omap3-igep.dtsi | 24 ++++++++++++++++++++++++ >>>> 1 file changed, 24 insertions(+) >>>> >>>> diff --git a/arch/arm/boot/dts/omap3-igep.dtsi >>>> b/arch/arm/boot/dts/omap3-igep.dtsi >>>> index 125fe00..c02e3c0 100644 >>>> --- a/arch/arm/boot/dts/omap3-igep.dtsi >>>> +++ b/arch/arm/boot/dts/omap3-igep.dtsi >>>> @@ -27,6 +27,20 @@ >>>> }; >>>> >>>> &omap3_pmx_core { >>>> + uart1_pins: pinmux_uart1_pins { >>>> + pinctrl-single,pins = < >>>> + 0x152 0x100 /* uart1_rx.uart1_rx INPUT | MODE0 >>>> */ >>>> + 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | >>>> MODE0 */ >>>> + >; >>>> + }; >>>> + >>>> + uart2_pins: pinmux_uart2_pins { >>>> + pinctrl-single,pins = < >>>> + 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | MODE0 >>>> */ >>>> + 0x148 0 /* uart2_tx.uart2_tx OUTPUT | >>>> MODE0 */ >>>> + >; >>>> + }; >>>> + >>>> uart3_pins: pinmux_uart3_pins { >>>> pinctrl-single,pins = < >>>> 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | MODE0 >>>> */ >>>> @@ -77,6 +91,16 @@ >>>> status = "disabled"; >>>> }; >>>> >>>> +&uart1 { >>>> + pinctrl-names = "default"; >>>> + pinctrl-0 = <&uart1_pins>; >>>> +}; >>>> + >>>> +&uart2 { >>>> + pinctrl-names = "default"; >>>> + pinctrl-0 = <&uart2_pins>; >>>> +}; >>>> + >>>> &uart3 { >>>> pinctrl-names = "default"; >>>> pinctrl-0 = <&uart3_pins>; >>>> >>> >>> That looks good to me. I'll apply it on top of javier's series for 3.9. >> >> Can you pin-point me to the repository where this patches are in right >> now? I tried to figure it out these days, but didn't found where to >> clone the repository from. >> >> Thanks, >> Matthias >> > > Hi Matthias, > > OMAP DT tree is: > git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git Hi all, unfortunately I can't find the patch in this tree. Benoit, can you pin point me to the right tree/branch? (I had a look in for_3.9/dts branch). Thanks, Matthias > > Hope it helps, > Javier
Hi Matthias, On 2/15/2013 10:35 AM, Matthias Brugger wrote: > 2013/1/26 Javier Martinez Canillas <martinez.javier@gmail.com>: >> On Sat, Jan 26, 2013 at 4:16 PM, Matthias Brugger <matthias.bgg@gmail.com> >> wrote: >>> Hi Benoit, >>> >>> 2012/12/12 Benoit Cousson <b-cousson@ti.com>: >>>> Hi Matthias, >>>> >>>> On 12/12/2012 04:33 PM, Matthias Brugger wrote: >>>>> This patch is a follow-up patch for Javier Martinez effort adding >>>>> initial >>>>> device tree support to IGEP technology devices. [1] >>>>> >>>>> It adds uart1 and uart2 bindings to the generic dtsi for the IGEP >>>>> boards. >>>>> >>>>> [1] http://www.spinics.net/lists/linux-omap/msg83409.html >>>>> >>>>> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> >>>>> --- >>>>> arch/arm/boot/dts/omap3-igep.dtsi | 24 ++++++++++++++++++++++++ >>>>> 1 file changed, 24 insertions(+) >>>>> >>>>> diff --git a/arch/arm/boot/dts/omap3-igep.dtsi >>>>> b/arch/arm/boot/dts/omap3-igep.dtsi >>>>> index 125fe00..c02e3c0 100644 >>>>> --- a/arch/arm/boot/dts/omap3-igep.dtsi >>>>> +++ b/arch/arm/boot/dts/omap3-igep.dtsi >>>>> @@ -27,6 +27,20 @@ >>>>> }; >>>>> >>>>> &omap3_pmx_core { >>>>> + uart1_pins: pinmux_uart1_pins { >>>>> + pinctrl-single,pins = < >>>>> + 0x152 0x100 /* uart1_rx.uart1_rx INPUT | MODE0 >>>>> */ >>>>> + 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | >>>>> MODE0 */ >>>>> + >; >>>>> + }; >>>>> + >>>>> + uart2_pins: pinmux_uart2_pins { >>>>> + pinctrl-single,pins = < >>>>> + 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | MODE0 >>>>> */ >>>>> + 0x148 0 /* uart2_tx.uart2_tx OUTPUT | >>>>> MODE0 */ >>>>> + >; >>>>> + }; >>>>> + >>>>> uart3_pins: pinmux_uart3_pins { >>>>> pinctrl-single,pins = < >>>>> 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | MODE0 >>>>> */ >>>>> @@ -77,6 +91,16 @@ >>>>> status = "disabled"; >>>>> }; >>>>> >>>>> +&uart1 { >>>>> + pinctrl-names = "default"; >>>>> + pinctrl-0 = <&uart1_pins>; >>>>> +}; >>>>> + >>>>> +&uart2 { >>>>> + pinctrl-names = "default"; >>>>> + pinctrl-0 = <&uart2_pins>; >>>>> +}; >>>>> + >>>>> &uart3 { >>>>> pinctrl-names = "default"; >>>>> pinctrl-0 = <&uart3_pins>; >>>>> >>>> >>>> That looks good to me. I'll apply it on top of javier's series for 3.9. >>> >>> Can you pin-point me to the repository where this patches are in right >>> now? I tried to figure it out these days, but didn't found where to >>> clone the repository from. >>> >>> Thanks, >>> Matthias >>> >> >> Hi Matthias, >> >> OMAP DT tree is: >> git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git > > Hi all, > > unfortunately I can't find the patch in this tree. Sorry about that. I've never pushed the latest branch, and was busy the past month. I'll refresh the branch with all the pending patches. Regards, Benoit -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Feb 15, 2013 at 11:03 AM, Cousson, Benoit <b-cousson@ti.com> wrote: > Hi Matthias, > > > On 2/15/2013 10:35 AM, Matthias Brugger wrote: >> >> 2013/1/26 Javier Martinez Canillas <martinez.javier@gmail.com>: >>> >>> On Sat, Jan 26, 2013 at 4:16 PM, Matthias Brugger >>> <matthias.bgg@gmail.com> >>> wrote: >>>> >>>> Hi Benoit, >>>> >>>> 2012/12/12 Benoit Cousson <b-cousson@ti.com>: >>>>> >>>>> Hi Matthias, >>>>> >>>>> On 12/12/2012 04:33 PM, Matthias Brugger wrote: >>>>>> >>>>>> This patch is a follow-up patch for Javier Martinez effort adding >>>>>> initial >>>>>> device tree support to IGEP technology devices. [1] >>>>>> >>>>>> It adds uart1 and uart2 bindings to the generic dtsi for the IGEP >>>>>> boards. >>>>>> >>>>>> [1] http://www.spinics.net/lists/linux-omap/msg83409.html >>>>>> >>>>>> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> >>>>>> --- >>>>>> arch/arm/boot/dts/omap3-igep.dtsi | 24 ++++++++++++++++++++++++ >>>>>> 1 file changed, 24 insertions(+) >>>>>> >>>>>> diff --git a/arch/arm/boot/dts/omap3-igep.dtsi >>>>>> b/arch/arm/boot/dts/omap3-igep.dtsi >>>>>> index 125fe00..c02e3c0 100644 >>>>>> --- a/arch/arm/boot/dts/omap3-igep.dtsi >>>>>> +++ b/arch/arm/boot/dts/omap3-igep.dtsi >>>>>> @@ -27,6 +27,20 @@ >>>>>> }; >>>>>> >>>>>> &omap3_pmx_core { >>>>>> + uart1_pins: pinmux_uart1_pins { >>>>>> + pinctrl-single,pins = < >>>>>> + 0x152 0x100 /* uart1_rx.uart1_rx INPUT | >>>>>> MODE0 >>>>>> */ >>>>>> + 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | >>>>>> MODE0 */ >>>>>> + >; >>>>>> + }; >>>>>> + >>>>>> + uart2_pins: pinmux_uart2_pins { >>>>>> + pinctrl-single,pins = < >>>>>> + 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | >>>>>> MODE0 >>>>>> */ >>>>>> + 0x148 0 /* uart2_tx.uart2_tx OUTPUT | >>>>>> MODE0 */ >>>>>> + >; >>>>>> + }; >>>>>> + >>>>>> uart3_pins: pinmux_uart3_pins { >>>>>> pinctrl-single,pins = < >>>>>> 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | >>>>>> MODE0 >>>>>> */ >>>>>> @@ -77,6 +91,16 @@ >>>>>> status = "disabled"; >>>>>> }; >>>>>> >>>>>> +&uart1 { >>>>>> + pinctrl-names = "default"; >>>>>> + pinctrl-0 = <&uart1_pins>; >>>>>> +}; >>>>>> + >>>>>> +&uart2 { >>>>>> + pinctrl-names = "default"; >>>>>> + pinctrl-0 = <&uart2_pins>; >>>>>> +}; >>>>>> + >>>>>> &uart3 { >>>>>> pinctrl-names = "default"; >>>>>> pinctrl-0 = <&uart3_pins>; >>>>>> >>>>> >>>>> That looks good to me. I'll apply it on top of javier's series for 3.9. >>>> >>>> >>>> Can you pin-point me to the repository where this patches are in right >>>> now? I tried to figure it out these days, but didn't found where to >>>> clone the repository from. >>>> >>>> Thanks, >>>> Matthias >>>> >>> >>> Hi Matthias, >>> >>> OMAP DT tree is: >>> git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git >> >> >> Hi all, >> >> unfortunately I can't find the patch in this tree. > > > Sorry about that. I've never pushed the latest branch, and was busy the past > month. I'll refresh the branch with all the pending patches. > > Regards, > Benoit > Hi Benoit, I realized that your for_3.9/dts branch has not landed in mainline yet and we are near to the end of the merge window. Are you still planing to include those changes for 3.9 or are you going to wait until the next release? Thanks a lot and best regards, Javier -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Javier, On 03/02/2013 02:52 AM, Javier Martinez Canillas wrote: > On Fri, Feb 15, 2013 at 11:03 AM, Cousson, Benoit <b-cousson@ti.com> wrote: >> Hi Matthias, >> >> >> On 2/15/2013 10:35 AM, Matthias Brugger wrote: >>> >>> 2013/1/26 Javier Martinez Canillas <martinez.javier@gmail.com>: >>>> >>>> On Sat, Jan 26, 2013 at 4:16 PM, Matthias Brugger >>>> <matthias.bgg@gmail.com> >>>> wrote: >>>>> >>>>> Hi Benoit, >>>>> >>>>> 2012/12/12 Benoit Cousson <b-cousson@ti.com>: >>>>>> >>>>>> Hi Matthias, >>>>>> >>>>>> On 12/12/2012 04:33 PM, Matthias Brugger wrote: >>>>>>> >>>>>>> This patch is a follow-up patch for Javier Martinez effort adding >>>>>>> initial >>>>>>> device tree support to IGEP technology devices. [1] >>>>>>> >>>>>>> It adds uart1 and uart2 bindings to the generic dtsi for the IGEP >>>>>>> boards. >>>>>>> >>>>>>> [1] http://www.spinics.net/lists/linux-omap/msg83409.html >>>>>>> >>>>>>> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> >>>>>>> --- >>>>>>> arch/arm/boot/dts/omap3-igep.dtsi | 24 ++++++++++++++++++++++++ >>>>>>> 1 file changed, 24 insertions(+) >>>>>>> >>>>>>> diff --git a/arch/arm/boot/dts/omap3-igep.dtsi >>>>>>> b/arch/arm/boot/dts/omap3-igep.dtsi >>>>>>> index 125fe00..c02e3c0 100644 >>>>>>> --- a/arch/arm/boot/dts/omap3-igep.dtsi >>>>>>> +++ b/arch/arm/boot/dts/omap3-igep.dtsi >>>>>>> @@ -27,6 +27,20 @@ >>>>>>> }; >>>>>>> >>>>>>> &omap3_pmx_core { >>>>>>> + uart1_pins: pinmux_uart1_pins { >>>>>>> + pinctrl-single,pins = < >>>>>>> + 0x152 0x100 /* uart1_rx.uart1_rx INPUT | >>>>>>> MODE0 >>>>>>> */ >>>>>>> + 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | >>>>>>> MODE0 */ >>>>>>> + >; >>>>>>> + }; >>>>>>> + >>>>>>> + uart2_pins: pinmux_uart2_pins { >>>>>>> + pinctrl-single,pins = < >>>>>>> + 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | >>>>>>> MODE0 >>>>>>> */ >>>>>>> + 0x148 0 /* uart2_tx.uart2_tx OUTPUT | >>>>>>> MODE0 */ >>>>>>> + >; >>>>>>> + }; >>>>>>> + >>>>>>> uart3_pins: pinmux_uart3_pins { >>>>>>> pinctrl-single,pins = < >>>>>>> 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | >>>>>>> MODE0 >>>>>>> */ >>>>>>> @@ -77,6 +91,16 @@ >>>>>>> status = "disabled"; >>>>>>> }; >>>>>>> >>>>>>> +&uart1 { >>>>>>> + pinctrl-names = "default"; >>>>>>> + pinctrl-0 = <&uart1_pins>; >>>>>>> +}; >>>>>>> + >>>>>>> +&uart2 { >>>>>>> + pinctrl-names = "default"; >>>>>>> + pinctrl-0 = <&uart2_pins>; >>>>>>> +}; >>>>>>> + >>>>>>> &uart3 { >>>>>>> pinctrl-names = "default"; >>>>>>> pinctrl-0 = <&uart3_pins>; >>>>>>> >>>>>> >>>>>> That looks good to me. I'll apply it on top of javier's series for 3.9. >>>>> >>>>> >>>>> Can you pin-point me to the repository where this patches are in right >>>>> now? I tried to figure it out these days, but didn't found where to >>>>> clone the repository from. >>>>> >>>>> Thanks, >>>>> Matthias >>>>> >>>> >>>> Hi Matthias, >>>> >>>> OMAP DT tree is: >>>> git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git >>> >>> >>> Hi all, >>> >>> unfortunately I can't find the patch in this tree. >> >> >> Sorry about that. I've never pushed the latest branch, and was busy the past >> month. I'll refresh the branch with all the pending patches. >> >> Regards, >> Benoit >> > > Hi Benoit, > > I realized that your for_3.9/dts branch has not landed in mainline yet > and we are near to the end of the merge window. > > Are you still planing to include those changes for 3.9 or are you > going to wait until the next release? I'm really sorry about that. I was not available to push it at the proper time. I've just rebased it on 3.9-rc2 and pushed it to a new branch. git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git for_3.10/dts It includes the one from Matthias and yours as well. I'm still checking my inbox to catch up on the new ones I missed. I'm planning to push this ASAP to avoid missing the deadline again. Regards, Benoit -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, Mar 13, 2013 at 5:41 PM, Benoit Cousson <b-cousson@ti.com> wrote: > Hi Javier, > > On 03/02/2013 02:52 AM, Javier Martinez Canillas wrote: >> On Fri, Feb 15, 2013 at 11:03 AM, Cousson, Benoit <b-cousson@ti.com> wrote: >>> Hi Matthias, >>> >>> >>> On 2/15/2013 10:35 AM, Matthias Brugger wrote: >>>> >>>> 2013/1/26 Javier Martinez Canillas <martinez.javier@gmail.com>: >>>>> >>>>> On Sat, Jan 26, 2013 at 4:16 PM, Matthias Brugger >>>>> <matthias.bgg@gmail.com> >>>>> wrote: >>>>>> >>>>>> Hi Benoit, >>>>>> >>>>>> 2012/12/12 Benoit Cousson <b-cousson@ti.com>: >>>>>>> >>>>>>> Hi Matthias, >>>>>>> >>>>>>> On 12/12/2012 04:33 PM, Matthias Brugger wrote: >>>>>>>> >>>>>>>> This patch is a follow-up patch for Javier Martinez effort adding >>>>>>>> initial >>>>>>>> device tree support to IGEP technology devices. [1] >>>>>>>> >>>>>>>> It adds uart1 and uart2 bindings to the generic dtsi for the IGEP >>>>>>>> boards. >>>>>>>> >>>>>>>> [1] http://www.spinics.net/lists/linux-omap/msg83409.html >>>>>>>> >>>>>>>> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> >>>>>>>> --- >>>>>>>> arch/arm/boot/dts/omap3-igep.dtsi | 24 ++++++++++++++++++++++++ >>>>>>>> 1 file changed, 24 insertions(+) >>>>>>>> >>>>>>>> diff --git a/arch/arm/boot/dts/omap3-igep.dtsi >>>>>>>> b/arch/arm/boot/dts/omap3-igep.dtsi >>>>>>>> index 125fe00..c02e3c0 100644 >>>>>>>> --- a/arch/arm/boot/dts/omap3-igep.dtsi >>>>>>>> +++ b/arch/arm/boot/dts/omap3-igep.dtsi >>>>>>>> @@ -27,6 +27,20 @@ >>>>>>>> }; >>>>>>>> >>>>>>>> &omap3_pmx_core { >>>>>>>> + uart1_pins: pinmux_uart1_pins { >>>>>>>> + pinctrl-single,pins = < >>>>>>>> + 0x152 0x100 /* uart1_rx.uart1_rx INPUT | >>>>>>>> MODE0 >>>>>>>> */ >>>>>>>> + 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | >>>>>>>> MODE0 */ >>>>>>>> + >; >>>>>>>> + }; >>>>>>>> + >>>>>>>> + uart2_pins: pinmux_uart2_pins { >>>>>>>> + pinctrl-single,pins = < >>>>>>>> + 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | >>>>>>>> MODE0 >>>>>>>> */ >>>>>>>> + 0x148 0 /* uart2_tx.uart2_tx OUTPUT | >>>>>>>> MODE0 */ >>>>>>>> + >; >>>>>>>> + }; >>>>>>>> + >>>>>>>> uart3_pins: pinmux_uart3_pins { >>>>>>>> pinctrl-single,pins = < >>>>>>>> 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | >>>>>>>> MODE0 >>>>>>>> */ >>>>>>>> @@ -77,6 +91,16 @@ >>>>>>>> status = "disabled"; >>>>>>>> }; >>>>>>>> >>>>>>>> +&uart1 { >>>>>>>> + pinctrl-names = "default"; >>>>>>>> + pinctrl-0 = <&uart1_pins>; >>>>>>>> +}; >>>>>>>> + >>>>>>>> +&uart2 { >>>>>>>> + pinctrl-names = "default"; >>>>>>>> + pinctrl-0 = <&uart2_pins>; >>>>>>>> +}; >>>>>>>> + >>>>>>>> &uart3 { >>>>>>>> pinctrl-names = "default"; >>>>>>>> pinctrl-0 = <&uart3_pins>; >>>>>>>> >>>>>>> >>>>>>> That looks good to me. I'll apply it on top of javier's series for 3.9. >>>>>> >>>>>> >>>>>> Can you pin-point me to the repository where this patches are in right >>>>>> now? I tried to figure it out these days, but didn't found where to >>>>>> clone the repository from. >>>>>> >>>>>> Thanks, >>>>>> Matthias >>>>>> >>>>> >>>>> Hi Matthias, >>>>> >>>>> OMAP DT tree is: >>>>> git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git >>>> >>>> >>>> Hi all, >>>> >>>> unfortunately I can't find the patch in this tree. >>> >>> >>> Sorry about that. I've never pushed the latest branch, and was busy the past >>> month. I'll refresh the branch with all the pending patches. >>> >>> Regards, >>> Benoit >>> >> >> Hi Benoit, >> >> I realized that your for_3.9/dts branch has not landed in mainline yet >> and we are near to the end of the merge window. >> >> Are you still planing to include those changes for 3.9 or are you >> going to wait until the next release? > > I'm really sorry about that. I was not available to push it at the proper time. > No worries, it was just a gentle remainder :-) > I've just rebased it on 3.9-rc2 and pushed it to a new branch. > git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git for_3.10/dts > > It includes the one from Matthias and yours as well. I'm still checking my inbox to catch up on the new ones I missed. > > I'm planning to push this ASAP to avoid missing the deadline again. > Great, thanks a lot for the information > > Regards, > Benoit Best regards, Javier -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 125fe00..c02e3c0 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -27,6 +27,20 @@ }; &omap3_pmx_core { + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x152 0x100 /* uart1_rx.uart1_rx INPUT | MODE0 */ + 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | MODE0 */ + >; + }; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | MODE0 */ + 0x148 0 /* uart2_tx.uart2_tx OUTPUT | MODE0 */ + >; + }; + uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | MODE0 */ @@ -77,6 +91,16 @@ status = "disabled"; }; +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + &uart3 { pinctrl-names = "default"; pinctrl-0 = <&uart3_pins>;
This patch is a follow-up patch for Javier Martinez effort adding initial device tree support to IGEP technology devices. [1] It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards. [1] http://www.spinics.net/lists/linux-omap/msg83409.html Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> --- arch/arm/boot/dts/omap3-igep.dtsi | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)