| Message ID | 201303290051.32106.sergei.shtylyov@cogentembedded.com (mailing list archive) |
|---|---|
| State | Accepted |
| Headers | show |
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Date: Fri, 29 Mar 2013 00:51:31 +0300 > Commit d0418bb7123f44b23d69ac349eec7daf9103472f (net: sh_eth: Add eth support > for R8A7779 device) was a failed attempt to add support for one of members of > the R-Car SoC family. That's for three reasons: it treated R8A7779 the same > as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask > in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in > R-Car Ether), and it didn't add a new register offset array despite the closest > SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether > registers have, and also some of the registers in this old mapping don't exist > on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not > adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724 > related section to its pristine state... > > Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Applied. -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Mar 29, 2013 at 12:51:31AM +0300, Sergei Shtylyov wrote: > Commit d0418bb7123f44b23d69ac349eec7daf9103472f (net: sh_eth: Add eth support > for R8A7779 device) was a failed attempt to add support for one of members of > the R-Car SoC family. That's for three reasons: it treated R8A7779 the same > as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask > in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in > R-Car Ether), and it didn't add a new register offset array despite the closest > SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether > registers have, and also some of the registers in this old mapping don't exist > on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not > adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724 > related section to its pristine state... > > Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Hi Sergei, thanks for this and sorry for not noticing it earlier. I will try exercising it on the r8a7790 lager. IIRC you previously mentioned that you were doing work on unravelling the #define mess in sh_eth. I am wondering if you have made any progress in that area. In particular, other than sh_eth it looks like the r8a7740 and r8a7790 could use a common .config. So it would be nice if sh_eth could support at least those two in the same build. > --- > The patch is against the David Miller's 'net-next.git' repo. > > Support for the other members of R-Car family such as R8A7778 and R8A7790 should > probably be added when they hit mainline (support for the former is already in > the 'next' branch of Simon Horman's 'renesas.git' repo). > > drivers/net/ethernet/renesas/sh_eth.c | 107 +++++++++++++++++++++++++++++++--- > include/linux/sh_eth.h | 1 > 2 files changed, 100 insertions(+), 8 deletions(-) > > Index: net-next/drivers/net/ethernet/renesas/sh_eth.c > =================================================================== > --- net-next.orig/drivers/net/ethernet/renesas/sh_eth.c > +++ net-next/drivers/net/ethernet/renesas/sh_eth.c > @@ -2,7 +2,8 @@ > * SuperH Ethernet device driver > * > * Copyright (C) 2006-2012 Nobuhiro Iwamatsu > - * Copyright (C) 2008-2012 Renesas Solutions Corp. > + * Copyright (C) 2008-2013 Renesas Solutions Corp. > + * Copyright (C) 2013 Cogent Embedded, Inc. > * > * This program is free software; you can redistribute it and/or modify it > * under the terms and conditions of the GNU General Public License, > @@ -147,6 +148,51 @@ static const u16 sh_eth_offset_gigabit[S > [FWALCR1] = 0x00b4, > }; > > +static const u16 sh_eth_offset_fast_rcar[SH_ETH_MAX_REGISTER_OFFSET] = { > + [ECMR] = 0x0300, > + [RFLR] = 0x0308, > + [ECSR] = 0x0310, > + [ECSIPR] = 0x0318, > + [PIR] = 0x0320, > + [PSR] = 0x0328, > + [RDMLR] = 0x0340, > + [IPGR] = 0x0350, > + [APR] = 0x0354, > + [MPR] = 0x0358, > + [RFCF] = 0x0360, > + [TPAUSER] = 0x0364, > + [TPAUSECR] = 0x0368, > + [MAHR] = 0x03c0, > + [MALR] = 0x03c8, > + [TROCR] = 0x03d0, > + [CDCR] = 0x03d4, > + [LCCR] = 0x03d8, > + [CNDCR] = 0x03dc, > + [CEFCR] = 0x03e4, > + [FRECR] = 0x03e8, > + [TSFRCR] = 0x03ec, > + [TLFRCR] = 0x03f0, > + [RFCR] = 0x03f4, > + [MAFCR] = 0x03f8, > + > + [EDMR] = 0x0200, > + [EDTRR] = 0x0208, > + [EDRRR] = 0x0210, > + [TDLAR] = 0x0218, > + [RDLAR] = 0x0220, > + [EESR] = 0x0228, > + [EESIPR] = 0x0230, > + [TRSCER] = 0x0238, > + [RMFCR] = 0x0240, > + [TFTR] = 0x0248, > + [FDR] = 0x0250, > + [RMCR] = 0x0258, > + [TFUCR] = 0x0264, > + [RFOCR] = 0x0268, > + [FCFTR] = 0x0270, > + [TRIMD] = 0x027c, > +}; > + > static const u16 sh_eth_offset_fast_sh4[SH_ETH_MAX_REGISTER_OFFSET] = { > [ECMR] = 0x0100, > [RFLR] = 0x0108, > @@ -296,7 +342,7 @@ static void sh_eth_select_mii(struct net > #endif > > /* There is CPU dependent code */ > -#if defined(CONFIG_CPU_SUBTYPE_SH7724) || defined(CONFIG_ARCH_R8A7779) > +#if defined(CONFIG_ARCH_R8A7779) > #define SH_ETH_RESET_DEFAULT 1 > static void sh_eth_set_duplex(struct net_device *ndev) > { > @@ -311,18 +357,60 @@ static void sh_eth_set_duplex(struct net > static void sh_eth_set_rate(struct net_device *ndev) > { > struct sh_eth_private *mdp = netdev_priv(ndev); > - unsigned int bits = ECMR_RTM; > > -#if defined(CONFIG_ARCH_R8A7779) > - bits |= ECMR_ELB; > -#endif > + switch (mdp->speed) { > + case 10: /* 10BASE */ > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~ECMR_ELB, ECMR); > + break; > + case 100:/* 100BASE */ > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | ECMR_ELB, ECMR); > + break; > + default: > + break; > + } > +} > + > +/* R8A7779 */ > +static struct sh_eth_cpu_data sh_eth_my_cpu_data = { > + .set_duplex = sh_eth_set_duplex, > + .set_rate = sh_eth_set_rate, > + > + .ecsr_value = ECSR_PSRTO | ECSR_LCHNG | ECSR_ICD, > + .ecsipr_value = ECSIPR_PSRTOIP | ECSIPR_LCHNGIP | ECSIPR_ICDIP, > + .eesipr_value = 0x01ff009f, > + > + .tx_check = EESR_FTC | EESR_CND | EESR_DLC | EESR_CD | EESR_RTO, > + .eesr_err_check = EESR_TWB | EESR_TABT | EESR_RABT | EESR_RDE | > + EESR_RFRMER | EESR_TFE | EESR_TDE | EESR_ECI, > + .tx_error_check = EESR_TWB | EESR_TABT | EESR_TDE | EESR_TFE, > + > + .apr = 1, > + .mpr = 1, > + .tpauser = 1, > + .hw_swap = 1, > +}; > +#elif defined(CONFIG_CPU_SUBTYPE_SH7724) > +#define SH_ETH_RESET_DEFAULT 1 > +static void sh_eth_set_duplex(struct net_device *ndev) > +{ > + struct sh_eth_private *mdp = netdev_priv(ndev); > + > + if (mdp->duplex) /* Full */ > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | ECMR_DM, ECMR); > + else /* Half */ > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~ECMR_DM, ECMR); > +} > + > +static void sh_eth_set_rate(struct net_device *ndev) > +{ > + struct sh_eth_private *mdp = netdev_priv(ndev); > > switch (mdp->speed) { > case 10: /* 10BASE */ > - sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~bits, ECMR); > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~ECMR_RTM, ECMR); > break; > case 100:/* 100BASE */ > - sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | bits, ECMR); > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | ECMR_RTM, ECMR); > break; > default: > break; > @@ -2521,6 +2609,9 @@ static const u16 *sh_eth_get_register_of > case SH_ETH_REG_GIGABIT: > reg_offset = sh_eth_offset_gigabit; > break; > + case SH_ETH_REG_FAST_RCAR: > + reg_offset = sh_eth_offset_fast_rcar; > + break; > case SH_ETH_REG_FAST_SH4: > reg_offset = sh_eth_offset_fast_sh4; > break; > Index: net-next/include/linux/sh_eth.h > =================================================================== > --- net-next.orig/include/linux/sh_eth.h > +++ net-next/include/linux/sh_eth.h > @@ -6,6 +6,7 @@ > enum {EDMAC_LITTLE_ENDIAN, EDMAC_BIG_ENDIAN}; > enum { > SH_ETH_REG_GIGABIT, > + SH_ETH_REG_FAST_RCAR, > SH_ETH_REG_FAST_SH4, > SH_ETH_REG_FAST_SH3_SH2 > }; > -- > To unsubscribe from this list: send the line "unsubscribe linux-sh" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Mon, Apr 08, 2013 at 11:39:37AM +0900, Simon Horman wrote: > On Fri, Mar 29, 2013 at 12:51:31AM +0300, Sergei Shtylyov wrote: > > Commit d0418bb7123f44b23d69ac349eec7daf9103472f (net: sh_eth: Add eth support > > for R8A7779 device) was a failed attempt to add support for one of members of > > the R-Car SoC family. That's for three reasons: it treated R8A7779 the same > > as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask > > in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in > > R-Car Ether), and it didn't add a new register offset array despite the closest > > SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether > > registers have, and also some of the registers in this old mapping don't exist > > on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not > > adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724 > > related section to its pristine state... > > > > Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> > > Hi Sergei, > > thanks for this and sorry for not noticing it earlier. > I will try exercising it on the r8a7790 lager. I am having a little trouble getting bringing up a link on the r8a7790 lager. I wonder if: * You know of any sh_eth side changes that need to be made, other than adding r8a7790 obvious ones relating to adding ARCH_R8A7790 wherever ARCH_R8A7779 is found. * You have any sample board code for the marzen/r8a7779 or bockw/r8a7778 handy. > > IIRC you previously mentioned that you were doing work on unravelling > the #define mess in sh_eth. I am wondering if you have made any progress > in that area. In particular, other than sh_eth it looks like > the r8a7740 and r8a7790 could use a common .config. So it would > be nice if sh_eth could support at least those two in the same build. > > > --- > > The patch is against the David Miller's 'net-next.git' repo. > > > > Support for the other members of R-Car family such as R8A7778 and R8A7790 should > > probably be added when they hit mainline (support for the former is already in > > the 'next' branch of Simon Horman's 'renesas.git' repo). > > > > drivers/net/ethernet/renesas/sh_eth.c | 107 +++++++++++++++++++++++++++++++--- > > include/linux/sh_eth.h | 1 > > 2 files changed, 100 insertions(+), 8 deletions(-) > > > > Index: net-next/drivers/net/ethernet/renesas/sh_eth.c > > =================================================================== > > --- net-next.orig/drivers/net/ethernet/renesas/sh_eth.c > > +++ net-next/drivers/net/ethernet/renesas/sh_eth.c > > @@ -2,7 +2,8 @@ > > * SuperH Ethernet device driver > > * > > * Copyright (C) 2006-2012 Nobuhiro Iwamatsu > > - * Copyright (C) 2008-2012 Renesas Solutions Corp. > > + * Copyright (C) 2008-2013 Renesas Solutions Corp. > > + * Copyright (C) 2013 Cogent Embedded, Inc. > > * > > * This program is free software; you can redistribute it and/or modify it > > * under the terms and conditions of the GNU General Public License, > > @@ -147,6 +148,51 @@ static const u16 sh_eth_offset_gigabit[S > > [FWALCR1] = 0x00b4, > > }; > > > > +static const u16 sh_eth_offset_fast_rcar[SH_ETH_MAX_REGISTER_OFFSET] = { > > + [ECMR] = 0x0300, > > + [RFLR] = 0x0308, > > + [ECSR] = 0x0310, > > + [ECSIPR] = 0x0318, > > + [PIR] = 0x0320, > > + [PSR] = 0x0328, > > + [RDMLR] = 0x0340, > > + [IPGR] = 0x0350, > > + [APR] = 0x0354, > > + [MPR] = 0x0358, > > + [RFCF] = 0x0360, > > + [TPAUSER] = 0x0364, > > + [TPAUSECR] = 0x0368, > > + [MAHR] = 0x03c0, > > + [MALR] = 0x03c8, > > + [TROCR] = 0x03d0, > > + [CDCR] = 0x03d4, > > + [LCCR] = 0x03d8, > > + [CNDCR] = 0x03dc, > > + [CEFCR] = 0x03e4, > > + [FRECR] = 0x03e8, > > + [TSFRCR] = 0x03ec, > > + [TLFRCR] = 0x03f0, > > + [RFCR] = 0x03f4, > > + [MAFCR] = 0x03f8, > > + > > + [EDMR] = 0x0200, > > + [EDTRR] = 0x0208, > > + [EDRRR] = 0x0210, > > + [TDLAR] = 0x0218, > > + [RDLAR] = 0x0220, > > + [EESR] = 0x0228, > > + [EESIPR] = 0x0230, > > + [TRSCER] = 0x0238, > > + [RMFCR] = 0x0240, > > + [TFTR] = 0x0248, > > + [FDR] = 0x0250, > > + [RMCR] = 0x0258, > > + [TFUCR] = 0x0264, > > + [RFOCR] = 0x0268, > > + [FCFTR] = 0x0270, > > + [TRIMD] = 0x027c, > > +}; > > + > > static const u16 sh_eth_offset_fast_sh4[SH_ETH_MAX_REGISTER_OFFSET] = { > > [ECMR] = 0x0100, > > [RFLR] = 0x0108, > > @@ -296,7 +342,7 @@ static void sh_eth_select_mii(struct net > > #endif > > > > /* There is CPU dependent code */ > > -#if defined(CONFIG_CPU_SUBTYPE_SH7724) || defined(CONFIG_ARCH_R8A7779) > > +#if defined(CONFIG_ARCH_R8A7779) > > #define SH_ETH_RESET_DEFAULT 1 > > static void sh_eth_set_duplex(struct net_device *ndev) > > { > > @@ -311,18 +357,60 @@ static void sh_eth_set_duplex(struct net > > static void sh_eth_set_rate(struct net_device *ndev) > > { > > struct sh_eth_private *mdp = netdev_priv(ndev); > > - unsigned int bits = ECMR_RTM; > > > > -#if defined(CONFIG_ARCH_R8A7779) > > - bits |= ECMR_ELB; > > -#endif > > + switch (mdp->speed) { > > + case 10: /* 10BASE */ > > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~ECMR_ELB, ECMR); > > + break; > > + case 100:/* 100BASE */ > > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | ECMR_ELB, ECMR); > > + break; > > + default: > > + break; > > + } > > +} > > + > > +/* R8A7779 */ > > +static struct sh_eth_cpu_data sh_eth_my_cpu_data = { > > + .set_duplex = sh_eth_set_duplex, > > + .set_rate = sh_eth_set_rate, > > + > > + .ecsr_value = ECSR_PSRTO | ECSR_LCHNG | ECSR_ICD, > > + .ecsipr_value = ECSIPR_PSRTOIP | ECSIPR_LCHNGIP | ECSIPR_ICDIP, > > + .eesipr_value = 0x01ff009f, > > + > > + .tx_check = EESR_FTC | EESR_CND | EESR_DLC | EESR_CD | EESR_RTO, > > + .eesr_err_check = EESR_TWB | EESR_TABT | EESR_RABT | EESR_RDE | > > + EESR_RFRMER | EESR_TFE | EESR_TDE | EESR_ECI, > > + .tx_error_check = EESR_TWB | EESR_TABT | EESR_TDE | EESR_TFE, > > + > > + .apr = 1, > > + .mpr = 1, > > + .tpauser = 1, > > + .hw_swap = 1, > > +}; > > +#elif defined(CONFIG_CPU_SUBTYPE_SH7724) > > +#define SH_ETH_RESET_DEFAULT 1 > > +static void sh_eth_set_duplex(struct net_device *ndev) > > +{ > > + struct sh_eth_private *mdp = netdev_priv(ndev); > > + > > + if (mdp->duplex) /* Full */ > > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | ECMR_DM, ECMR); > > + else /* Half */ > > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~ECMR_DM, ECMR); > > +} > > + > > +static void sh_eth_set_rate(struct net_device *ndev) > > +{ > > + struct sh_eth_private *mdp = netdev_priv(ndev); > > > > switch (mdp->speed) { > > case 10: /* 10BASE */ > > - sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~bits, ECMR); > > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~ECMR_RTM, ECMR); > > break; > > case 100:/* 100BASE */ > > - sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | bits, ECMR); > > + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | ECMR_RTM, ECMR); > > break; > > default: > > break; > > @@ -2521,6 +2609,9 @@ static const u16 *sh_eth_get_register_of > > case SH_ETH_REG_GIGABIT: > > reg_offset = sh_eth_offset_gigabit; > > break; > > + case SH_ETH_REG_FAST_RCAR: > > + reg_offset = sh_eth_offset_fast_rcar; > > + break; > > case SH_ETH_REG_FAST_SH4: > > reg_offset = sh_eth_offset_fast_sh4; > > break; > > Index: net-next/include/linux/sh_eth.h > > =================================================================== > > --- net-next.orig/include/linux/sh_eth.h > > +++ net-next/include/linux/sh_eth.h > > @@ -6,6 +6,7 @@ > > enum {EDMAC_LITTLE_ENDIAN, EDMAC_BIG_ENDIAN}; > > enum { > > SH_ETH_REG_GIGABIT, > > + SH_ETH_REG_FAST_RCAR, > > SH_ETH_REG_FAST_SH4, > > SH_ETH_REG_FAST_SH3_SH2 > > }; > > -- > > To unsubscribe from this list: send the line "unsubscribe linux-sh" in > > the body of a message to majordomo@vger.kernel.org > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello. On 08-04-2013 6:39, Simon Horman wrote: >> Commit d0418bb7123f44b23d69ac349eec7daf9103472f (net: sh_eth: Add eth support >> for R8A7779 device) was a failed attempt to add support for one of members of >> the R-Car SoC family. That's for three reasons: it treated R8A7779 the same >> as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask >> in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in >> R-Car Ether), and it didn't add a new register offset array despite the closest >> SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether >> registers have, and also some of the registers in this old mapping don't exist >> on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not >> adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724 >> related section to its pristine state... >> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> > Hi Sergei, > thanks for this and sorry for not noticing it earlier. > I will try exercising it on the r8a7790 lager. > IIRC you previously mentioned that you were doing work on unravelling > the #define mess in sh_eth. I am wondering if you have made any progress > in that area. Not much -- I was swithced to USB work. WBR, Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello. On 08-04-2013 13:04, Simon Horman wrote: >>> Commit d0418bb7123f44b23d69ac349eec7daf9103472f (net: sh_eth: Add eth support >>> for R8A7779 device) was a failed attempt to add support for one of members of >>> the R-Car SoC family. That's for three reasons: it treated R8A7779 the same >>> as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask >>> in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in >>> R-Car Ether), and it didn't add a new register offset array despite the closest >>> SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether >>> registers have, and also some of the registers in this old mapping don't exist >>> on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not >>> adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724 >>> related section to its pristine state... >>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> >> Hi Sergei, >> thanks for this and sorry for not noticing it earlier. >> I will try exercising it on the r8a7790 lager. > I am having a little trouble getting bringing up a link on the > r8a7790 lager. I wonder if: > * You know of any sh_eth side changes that need to be made, > other than adding r8a7790 obvious ones relating to adding > ARCH_R8A7790 wherever ARCH_R8A7779 is found. Unfortunately, the only datasheet for R8A7790 Ether I have is in Japanese. And I don't have the board info either. :-( > * You have any sample board code for the marzen/r8a7779 or > bockw/r8a7778 handy. On Marzen the driver simply doesn't work right (and I don't even have the datasheet for the Ethernet daughter board that I have, only for some other type of board), on the BOCK-W the driver works but I have only tested it with the version 1 of Morimoto-san's R8A7778/BOCK-W patches (which included pinmux support), so this patch doesn't compile anymore with the current renesas.git/next. With BOCK-W you need to set 'no_ether_link' in the platform data since the Ether's LINK signal is connected to PHY's link/activity LED output. WBR, Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Sergei, > >>> Commit d0418bb7123f44b23d69ac349eec7daf9103472f (net: sh_eth: > Add eth support > >>> for R8A7779 device) was a failed attempt to add support for one > of members of > >>> the R-Car SoC family. That's for three reasons: it treated > R8A7779 the same > >>> as SH7724 except including quite dirty hack adding ECMR_ELB bit > to the mask > >>> in sh_eth_set_rate() while not removing ECMR_RTM bit (despite > it's reserved in > >>> R-Car Ether), and it didn't add a new register offset array > despite the closest > >>> SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all > the R-Car Ether > >>> registers have, and also some of the registers in this old > mapping don't exist > >>> on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' > structure is not > >>> adequeate for R-Car too). Fix all these shortcomings, restoringthe SH7724 > >>> related section to its pristine state... > > >>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> > > >> Hi Sergei, > > >> thanks for this and sorry for not noticing it earlier. > >> I will try exercising it on the r8a7790 lager. > > > I am having a little trouble getting bringing up a link on the > > r8a7790 lager. I wonder if: > > > * You know of any sh_eth side changes that need to be made, > > other than adding r8a7790 obvious ones relating to adding > > ARCH_R8A7790 wherever ARCH_R8A7779 is found. > > Unfortunately, the only datasheet for R8A7790 Ether I have is inJapanese. > And I don't have the board info either. :-( > > > * You have any sample board code for the marzen/r8a7779 or > > bockw/r8a7778 handy. > > On Marzen the driver simply doesn't work right (and I don't evenhave the > datasheet for the Ethernet daughter board that I have, only for some other > type of board), on the BOCK-W the driver works but I have only tested it with > the version 1 of Morimoto-san's R8A7778/BOCK-W patches (which included pinmux > support), so this patch doesn't compile anymore with the current > renesas.git/next. With BOCK-W you need to set 'no_ether_link' in theplatform > data since the Ether's LINK signal is connected to PHY's link/ > activity LED output. Thanks for the patch. When I added r8a7779 support, I had a rather poor manual with a lot of information missing. I submitted the patch once I got the driver working on a Marzen board, with an REE Expansion Board. One of the main changes you have made is adjusting the offset of the control registers. When I did this work originally, I just assumed that the base address start at 0x1DE00200, i.e. it included the 0x200 offset. This made sense as the registers are then identically positioned to sh4a. Regards Phil -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello. On 08-04-2013 18:40, phil.edworthy@renesas.com wrote: > Thanks for the patch. When I added r8a7779 support, I had a rather poor > manual with a lot of information missing. I submitted the patch once I got > the driver working on a Marzen board, with an REE Expansion Board. That must be 3rd type of the expansion board even. I have documentation on some Y-R-CAR-H1-BOARD-EXP board, and I have the R0P7779A00020S board mounted below Marzen. They seem very different as the latter don't have any switches on it. > One of the main changes you have made is adjusting the offset of the > control registers. When I did this work originally, I just assumed that > the base address start at 0x1DE00200, i.e. it included the 0x200 offset. > This made sense as the registers are then identically positioned to sh4a. Yes, but not all SH4 registers exist on R-Car and the Ether base is 0xFDE00000 according to the datasheet. > Regards > Phil WBR, Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Index: net-next/drivers/net/ethernet/renesas/sh_eth.c =================================================================== --- net-next.orig/drivers/net/ethernet/renesas/sh_eth.c +++ net-next/drivers/net/ethernet/renesas/sh_eth.c @@ -2,7 +2,8 @@ * SuperH Ethernet device driver * * Copyright (C) 2006-2012 Nobuhiro Iwamatsu - * Copyright (C) 2008-2012 Renesas Solutions Corp. + * Copyright (C) 2008-2013 Renesas Solutions Corp. + * Copyright (C) 2013 Cogent Embedded, Inc. * * This program is free software; you can redistribute it and/or modify it * under the terms and conditions of the GNU General Public License, @@ -147,6 +148,51 @@ static const u16 sh_eth_offset_gigabit[S [FWALCR1] = 0x00b4, }; +static const u16 sh_eth_offset_fast_rcar[SH_ETH_MAX_REGISTER_OFFSET] = { + [ECMR] = 0x0300, + [RFLR] = 0x0308, + [ECSR] = 0x0310, + [ECSIPR] = 0x0318, + [PIR] = 0x0320, + [PSR] = 0x0328, + [RDMLR] = 0x0340, + [IPGR] = 0x0350, + [APR] = 0x0354, + [MPR] = 0x0358, + [RFCF] = 0x0360, + [TPAUSER] = 0x0364, + [TPAUSECR] = 0x0368, + [MAHR] = 0x03c0, + [MALR] = 0x03c8, + [TROCR] = 0x03d0, + [CDCR] = 0x03d4, + [LCCR] = 0x03d8, + [CNDCR] = 0x03dc, + [CEFCR] = 0x03e4, + [FRECR] = 0x03e8, + [TSFRCR] = 0x03ec, + [TLFRCR] = 0x03f0, + [RFCR] = 0x03f4, + [MAFCR] = 0x03f8, + + [EDMR] = 0x0200, + [EDTRR] = 0x0208, + [EDRRR] = 0x0210, + [TDLAR] = 0x0218, + [RDLAR] = 0x0220, + [EESR] = 0x0228, + [EESIPR] = 0x0230, + [TRSCER] = 0x0238, + [RMFCR] = 0x0240, + [TFTR] = 0x0248, + [FDR] = 0x0250, + [RMCR] = 0x0258, + [TFUCR] = 0x0264, + [RFOCR] = 0x0268, + [FCFTR] = 0x0270, + [TRIMD] = 0x027c, +}; + static const u16 sh_eth_offset_fast_sh4[SH_ETH_MAX_REGISTER_OFFSET] = { [ECMR] = 0x0100, [RFLR] = 0x0108, @@ -296,7 +342,7 @@ static void sh_eth_select_mii(struct net #endif /* There is CPU dependent code */ -#if defined(CONFIG_CPU_SUBTYPE_SH7724) || defined(CONFIG_ARCH_R8A7779) +#if defined(CONFIG_ARCH_R8A7779) #define SH_ETH_RESET_DEFAULT 1 static void sh_eth_set_duplex(struct net_device *ndev) { @@ -311,18 +357,60 @@ static void sh_eth_set_duplex(struct net static void sh_eth_set_rate(struct net_device *ndev) { struct sh_eth_private *mdp = netdev_priv(ndev); - unsigned int bits = ECMR_RTM; -#if defined(CONFIG_ARCH_R8A7779) - bits |= ECMR_ELB; -#endif + switch (mdp->speed) { + case 10: /* 10BASE */ + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~ECMR_ELB, ECMR); + break; + case 100:/* 100BASE */ + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | ECMR_ELB, ECMR); + break; + default: + break; + } +} + +/* R8A7779 */ +static struct sh_eth_cpu_data sh_eth_my_cpu_data = { + .set_duplex = sh_eth_set_duplex, + .set_rate = sh_eth_set_rate, + + .ecsr_value = ECSR_PSRTO | ECSR_LCHNG | ECSR_ICD, + .ecsipr_value = ECSIPR_PSRTOIP | ECSIPR_LCHNGIP | ECSIPR_ICDIP, + .eesipr_value = 0x01ff009f, + + .tx_check = EESR_FTC | EESR_CND | EESR_DLC | EESR_CD | EESR_RTO, + .eesr_err_check = EESR_TWB | EESR_TABT | EESR_RABT | EESR_RDE | + EESR_RFRMER | EESR_TFE | EESR_TDE | EESR_ECI, + .tx_error_check = EESR_TWB | EESR_TABT | EESR_TDE | EESR_TFE, + + .apr = 1, + .mpr = 1, + .tpauser = 1, + .hw_swap = 1, +}; +#elif defined(CONFIG_CPU_SUBTYPE_SH7724) +#define SH_ETH_RESET_DEFAULT 1 +static void sh_eth_set_duplex(struct net_device *ndev) +{ + struct sh_eth_private *mdp = netdev_priv(ndev); + + if (mdp->duplex) /* Full */ + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | ECMR_DM, ECMR); + else /* Half */ + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~ECMR_DM, ECMR); +} + +static void sh_eth_set_rate(struct net_device *ndev) +{ + struct sh_eth_private *mdp = netdev_priv(ndev); switch (mdp->speed) { case 10: /* 10BASE */ - sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~bits, ECMR); + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) & ~ECMR_RTM, ECMR); break; case 100:/* 100BASE */ - sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | bits, ECMR); + sh_eth_write(ndev, sh_eth_read(ndev, ECMR) | ECMR_RTM, ECMR); break; default: break; @@ -2521,6 +2609,9 @@ static const u16 *sh_eth_get_register_of case SH_ETH_REG_GIGABIT: reg_offset = sh_eth_offset_gigabit; break; + case SH_ETH_REG_FAST_RCAR: + reg_offset = sh_eth_offset_fast_rcar; + break; case SH_ETH_REG_FAST_SH4: reg_offset = sh_eth_offset_fast_sh4; break; Index: net-next/include/linux/sh_eth.h =================================================================== --- net-next.orig/include/linux/sh_eth.h +++ net-next/include/linux/sh_eth.h @@ -6,6 +6,7 @@ enum {EDMAC_LITTLE_ENDIAN, EDMAC_BIG_ENDIAN}; enum { SH_ETH_REG_GIGABIT, + SH_ETH_REG_FAST_RCAR, SH_ETH_REG_FAST_SH4, SH_ETH_REG_FAST_SH3_SH2 };
Commit d0418bb7123f44b23d69ac349eec7daf9103472f (net: sh_eth: Add eth support for R8A7779 device) was a failed attempt to add support for one of members of the R-Car SoC family. That's for three reasons: it treated R8A7779 the same as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in R-Car Ether), and it didn't add a new register offset array despite the closest SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether registers have, and also some of the registers in this old mapping don't exist on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724 related section to its pristine state... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> --- The patch is against the David Miller's 'net-next.git' repo. Support for the other members of R-Car family such as R8A7778 and R8A7790 should probably be added when they hit mainline (support for the former is already in the 'next' branch of Simon Horman's 'renesas.git' repo). drivers/net/ethernet/renesas/sh_eth.c | 107 +++++++++++++++++++++++++++++++--- include/linux/sh_eth.h | 1 2 files changed, 100 insertions(+), 8 deletions(-) -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html