| Message ID | 1366015721-25608-1-git-send-email-rogerq@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
* Roger Quadros <rogerq@ti.com> [130415 01:53]: > Provide the RESET and Power regulators for the USB PHY, > the USB Host port mode and the PHY device. > > The USB PHY needs AUXCLK3 to operate. Provide this information > as well. > > Also provide pin multiplexer information for the USB host > pins. > > This patch depends on OMAP clock binding introduced in > https://lkml.org/lkml/2013/4/12/407 Cool looks like EHCI works with this on my panda with linux next booting with DT. One comment below. Regards, Tony > CC: Benoît Cousson <b-cousson@ti.com> > Signed-off-by: Roger Quadros <rogerq@ti.com> > --- > arch/arm/boot/dts/omap4-panda-common.dtsi | 58 +++++++++++++++++++++++++++++ > arch/arm/boot/dts/omap4.dtsi | 5 ++ > 2 files changed, 63 insertions(+), 0 deletions(-) > > diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi > index 03bd60d..628f744 100644 > --- a/arch/arm/boot/dts/omap4-panda-common.dtsi > +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi > @@ -54,6 +54,38 @@ > "AFML", "Line In", > "AFMR", "Line In"; > }; > + > + /* HS USB Port 1 RESET */ > + hsusb1_reset: hsusb1_reset_reg { > + compatible = "regulator-fixed"; > + regulator-name = "hsusb1_reset"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio2 30 0>; /* gpio_62 */ > + startup-delay-us = <70000>; > + enable-active-high; > + }; > + > + /* HS USB Port 1 Power */ > + hsusb1_power: hsusb1_power_reg { > + compatible = "regulator-fixed"; > + regulator-name = "hsusb1_vbus"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio1 1 0>; /* gpio_1 */ > + startup-delay-us = <70000>; > + enable-active-high; > + }; > + > + /* HS USB Host PHY on PORT 1 */ > + hsusb1_phy: hsusb1_phy { > + compatible = "usb-nop-xceiv"; > + reset-supply = <&hsusb1_reset>; > + vcc-supply = <&hsusb1_power>; > + clocks = <&auxclk3>; > + clock-names = "main_clk"; > + clock-frequency = <19200000>; > + }; > }; > > &omap4_pmx_core { > @@ -64,6 +96,7 @@ > &mcbsp1_pins > &dss_hdmi_pins > &tpd12s015_pins > + &hsusbb1_pins > >; > > twl6040_pins: pinmux_twl6040_pins { > @@ -108,6 +141,23 @@ > >; > }; > > + hsusbb1_pins: pinmux_hsusbb1_pins { > + pinctrl-single,pins = < > + 0x82 0x10C /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk INPUT | PULLDOWN */ > + 0x84 0x4 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */ > + 0x86 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */ > + 0x88 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */ > + 0x8a 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */ > + 0x8c 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */ > + 0x8e 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */ > + 0x90 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */ > + 0x92 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */ > + 0x94 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */ > + 0x96 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */ > + 0x98 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */ > + >; > + }; > + > i2c1_pins: pinmux_i2c1_pins { > pinctrl-single,pins = < > 0xe2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */ Looks like your comments are wrong above, it's not PULLDOWN? Also the naming should be mode0name.modename to be consistent. Here's what I dumped out, please check and replace spaces with tabs: 0x82 0x10c /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk gpio84 INPUT_PULLDOWN | MODE4 */ 0x84 0x4 /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp gpio85 OUTPUT | MODE4 */ 0x86 0x104 /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir gpio86 INPUT | MODE4 */ 0x88 0x104 /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt gpio87 INPUT | MODE4 */ 0x8a 0x104 /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 gpio88 INPUT | MODE4 */ 0x8c 0x104 /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 gpio89 INPUT | MODE4 */ 0x8e 0x104 /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 gpio90 INPUT | MODE4 */ 0x90 0x104 /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 gpio91 INPUT | MODE4 */ 0x92 0x104 /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 gpio92 INPUT | MODE4 */ 0x94 0x104 /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 gpio93 INPUT | MODE4 */ 0x96 0x104 /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 gpio94 INPUT | MODE4 */ 0x98 0x104 /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 gpio95 INPUT | MODE4 */ Then at some point soon we can just replace the mode value with DT preprocessor automatically. > @@ -249,3 +299,11 @@ > mode = <3>; > power = <50>; > }; > + > +&usbhshost { > + port1-mode = "ehci-phy"; > +}; > + > +&usbhsehci { > + phys = <&hsusb1_phy>; > +}; > diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi > index 2a56428..bd6036e 100644 > --- a/arch/arm/boot/dts/omap4.dtsi > +++ b/arch/arm/boot/dts/omap4.dtsi > @@ -660,5 +660,10 @@ > ram-bits = <12>; > ti,has-mailbox; > }; > + > + auxclk3: auxclk3 { > + #clock-cells = <0>; > + compatible = "ti,omap-clock"; > + }; > }; > }; > -- > 1.7.4.1 >
On 04/18/2013 11:09 PM, Tony Lindgren wrote: > * Roger Quadros <rogerq@ti.com> [130415 01:53]: >> Provide the RESET and Power regulators for the USB PHY, >> the USB Host port mode and the PHY device. >> >> The USB PHY needs AUXCLK3 to operate. Provide this information >> as well. >> >> Also provide pin multiplexer information for the USB host >> pins. >> >> This patch depends on OMAP clock binding introduced in >> https://lkml.org/lkml/2013/4/12/407 > > Cool looks like EHCI works with this on my panda with linux > next booting with DT. One comment below. > > Regards, > > Tony > > >> CC: Benoît Cousson <b-cousson@ti.com> >> Signed-off-by: Roger Quadros <rogerq@ti.com> >> --- >> arch/arm/boot/dts/omap4-panda-common.dtsi | 58 +++++++++++++++++++++++++++++ >> arch/arm/boot/dts/omap4.dtsi | 5 ++ >> 2 files changed, 63 insertions(+), 0 deletions(-) >> >> diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi >> index 03bd60d..628f744 100644 >> --- a/arch/arm/boot/dts/omap4-panda-common.dtsi >> +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi >> @@ -54,6 +54,38 @@ >> "AFML", "Line In", >> "AFMR", "Line In"; >> }; >> + >> + /* HS USB Port 1 RESET */ >> + hsusb1_reset: hsusb1_reset_reg { >> + compatible = "regulator-fixed"; >> + regulator-name = "hsusb1_reset"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + gpio = <&gpio2 30 0>; /* gpio_62 */ >> + startup-delay-us = <70000>; >> + enable-active-high; >> + }; >> + >> + /* HS USB Port 1 Power */ >> + hsusb1_power: hsusb1_power_reg { >> + compatible = "regulator-fixed"; >> + regulator-name = "hsusb1_vbus"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + gpio = <&gpio1 1 0>; /* gpio_1 */ >> + startup-delay-us = <70000>; >> + enable-active-high; >> + }; >> + >> + /* HS USB Host PHY on PORT 1 */ >> + hsusb1_phy: hsusb1_phy { >> + compatible = "usb-nop-xceiv"; >> + reset-supply = <&hsusb1_reset>; >> + vcc-supply = <&hsusb1_power>; >> + clocks = <&auxclk3>; >> + clock-names = "main_clk"; >> + clock-frequency = <19200000>; >> + }; >> }; >> >> &omap4_pmx_core { >> @@ -64,6 +96,7 @@ >> &mcbsp1_pins >> &dss_hdmi_pins >> &tpd12s015_pins >> + &hsusbb1_pins >> >; >> >> twl6040_pins: pinmux_twl6040_pins { >> @@ -108,6 +141,23 @@ >> >; >> }; >> >> + hsusbb1_pins: pinmux_hsusbb1_pins { >> + pinctrl-single,pins = < >> + 0x82 0x10C /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk INPUT | PULLDOWN */ >> + 0x84 0x4 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */ >> + 0x86 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */ >> + 0x88 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */ >> + 0x8a 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */ >> + 0x8c 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */ >> + 0x8e 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */ >> + 0x90 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */ >> + 0x92 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */ >> + 0x94 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */ >> + 0x96 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */ >> + 0x98 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */ >> + >; >> + }; >> + >> i2c1_pins: pinmux_i2c1_pins { >> pinctrl-single,pins = < >> 0xe2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */ > > Looks like your comments are wrong above, it's not PULLDOWN? Also right it's not. > the naming should be mode0name.modename to be consistent. Here's > what I dumped out, please check and replace spaces with tabs: > > 0x82 0x10c /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk gpio84 INPUT_PULLDOWN | MODE4 */ > 0x84 0x4 /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp gpio85 OUTPUT | MODE4 */ > 0x86 0x104 /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir gpio86 INPUT | MODE4 */ > 0x88 0x104 /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt gpio87 INPUT | MODE4 */ > 0x8a 0x104 /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 gpio88 INPUT | MODE4 */ > 0x8c 0x104 /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 gpio89 INPUT | MODE4 */ > 0x8e 0x104 /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 gpio90 INPUT | MODE4 */ > 0x90 0x104 /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 gpio91 INPUT | MODE4 */ > 0x92 0x104 /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 gpio92 INPUT | MODE4 */ > 0x94 0x104 /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 gpio93 INPUT | MODE4 */ > 0x96 0x104 /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 gpio94 INPUT | MODE4 */ > 0x98 0x104 /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 gpio95 INPUT | MODE4 */ I don't think gpioXX is necessary as we aren't using any of them as GPIOs. cheers, -roger
* Roger Quadros <rogerq@ti.com> [130419 01:23]: > On 04/18/2013 11:09 PM, Tony Lindgren wrote: > > > the naming should be mode0name.modename to be consistent. Here's > > what I dumped out, please check and replace spaces with tabs: > > > > 0x82 0x10c /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk gpio84 INPUT_PULLDOWN | MODE4 */ > > 0x84 0x4 /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp gpio85 OUTPUT | MODE4 */ > > 0x86 0x104 /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir gpio86 INPUT | MODE4 */ > > 0x88 0x104 /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt gpio87 INPUT | MODE4 */ > > 0x8a 0x104 /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 gpio88 INPUT | MODE4 */ > > 0x8c 0x104 /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 gpio89 INPUT | MODE4 */ > > 0x8e 0x104 /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 gpio90 INPUT | MODE4 */ > > 0x90 0x104 /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 gpio91 INPUT | MODE4 */ > > 0x92 0x104 /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 gpio92 INPUT | MODE4 */ > > 0x94 0x104 /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 gpio93 INPUT | MODE4 */ > > 0x96 0x104 /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 gpio94 INPUT | MODE4 */ > > 0x98 0x104 /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 gpio95 INPUT | MODE4 */ > > I don't think gpioXX is necessary as we aren't using any of them as GPIOs. Oops sorry yeah please check as that's something I just dumped from the system. The gpio numbering is just data for debugging that you can leave out. Also check please check I dumped the right pins, I just grepped for usbb1. Regards, Tony
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 03bd60d..628f744 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -54,6 +54,38 @@ "AFML", "Line In", "AFMR", "Line In"; }; + + /* HS USB Port 1 RESET */ + hsusb1_reset: hsusb1_reset_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb1_reset"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 30 0>; /* gpio_62 */ + startup-delay-us = <70000>; + enable-active-high; + }; + + /* HS USB Port 1 Power */ + hsusb1_power: hsusb1_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb1_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 1 0>; /* gpio_1 */ + startup-delay-us = <70000>; + enable-active-high; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + reset-supply = <&hsusb1_reset>; + vcc-supply = <&hsusb1_power>; + clocks = <&auxclk3>; + clock-names = "main_clk"; + clock-frequency = <19200000>; + }; }; &omap4_pmx_core { @@ -64,6 +96,7 @@ &mcbsp1_pins &dss_hdmi_pins &tpd12s015_pins + &hsusbb1_pins >; twl6040_pins: pinmux_twl6040_pins { @@ -108,6 +141,23 @@ >; }; + hsusbb1_pins: pinmux_hsusbb1_pins { + pinctrl-single,pins = < + 0x82 0x10C /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk INPUT | PULLDOWN */ + 0x84 0x4 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */ + 0x86 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */ + 0x88 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */ + 0x8a 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */ + 0x8c 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */ + 0x8e 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */ + 0x90 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */ + 0x92 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */ + 0x94 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */ + 0x96 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */ + 0x98 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */ + >; + }; + i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < 0xe2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */ @@ -249,3 +299,11 @@ mode = <3>; power = <50>; }; + +&usbhshost { + port1-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy>; +}; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 2a56428..bd6036e 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -660,5 +660,10 @@ ram-bits = <12>; ti,has-mailbox; }; + + auxclk3: auxclk3 { + #clock-cells = <0>; + compatible = "ti,omap-clock"; + }; }; };
Provide the RESET and Power regulators for the USB PHY, the USB Host port mode and the PHY device. The USB PHY needs AUXCLK3 to operate. Provide this information as well. Also provide pin multiplexer information for the USB host pins. This patch depends on OMAP clock binding introduced in https://lkml.org/lkml/2013/4/12/407 CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> --- arch/arm/boot/dts/omap4-panda-common.dtsi | 58 +++++++++++++++++++++++++++++ arch/arm/boot/dts/omap4.dtsi | 5 ++ 2 files changed, 63 insertions(+), 0 deletions(-)