Message ID | 1368435233-8587-4-git-send-email-horms+renesas@verge.net.au (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On 13-05-2013 12:53, Simon Horman wrote: > The lager board has pins 1 - 4 of SW2 wired up to GPIO pins. > This patch allows access to those pins as KEYS 1 - 4 using > gpio-keys. > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> [...] > diff --git a/arch/arm/mach-shmobile/board-lager.c b/arch/arm/mach-shmobile/board-lager.c > index 6a1ba38..4d1b42b 100644 > --- a/arch/arm/mach-shmobile/board-lager.c > +++ b/arch/arm/mach-shmobile/board-lager.c [...] > @@ -52,6 +55,22 @@ static struct gpio_led_platform_data lager_leds_pdata = { > .num_leds = ARRAY_SIZE(lager_leds), > }; > > +/* GPIO KEY */ > +#define GPIO_KEY(c, g, d, ...) \ > + { .code = c, .gpio = g, .desc = d, .active_low = 1 } > + > +static struct gpio_keys_button gpio_buttons[] = { > + GPIO_KEY(KEY_4, RCAR_GP_PIN(1, 28), "SW2-pin4"), > + GPIO_KEY(KEY_3, RCAR_GP_PIN(1, 26), "SW2-pin3"), > + GPIO_KEY(KEY_2, RCAR_GP_PIN(1, 24), "SW2-pin2"), > + GPIO_KEY(KEY_1, RCAR_GP_PIN(1, 14), "SW2-pin1"), > +}; > + > +static struct gpio_keys_platform_data lager_keys_pdata = { You forgot to annotate this with __initdata. > + .buttons = gpio_buttons, > + .nbuttons = ARRAY_SIZE(gpio_buttons), > +}; > + > static const struct pinctrl_map lager_pinctrl_map[] = { > /* SCIF0 (CN19: DEBUG SERIAL0) */ > PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7790", > @@ -73,6 +92,9 @@ static void __init lager_add_standard_devices(void) > platform_device_register_data(&platform_bus, "leds-gpio", -1, > &lager_leds_pdata, > sizeof(lager_leds_pdata)); > + platform_device_register_data(&platform_bus, "gpio-keys", -1, > + &lager_keys_pdata, > + sizeof(lager_keys_pdata)); > } WBR, Sergei
Hi Simon, Thank you for the patch. On Monday 13 May 2013 17:53:53 Simon Horman wrote: > The lager board has pins 1 - 4 of SW2 wired up to GPIO pins. > This patch allows access to those pins as KEYS 1 - 4 using > gpio-keys. > > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > --- > > This patch has run time dependencies on > 1. "gpio-rcar: Add support for IRQ_TYPE_EDGE_BOTH" > 2. "ARM: shmobile: r8a7790: Configure R-Car GPIO for IRQ_TYPE_EDGE_BOTH" > > Without those dependencies satisfied the gpio-keys driver will > fail to be initialise itself. The boot should be otherwise successful > and the board otherwise functional. > --- > arch/arm/mach-shmobile/board-lager.c | 22 ++++++++++++++++++++++ > 1 file changed, 22 insertions(+) > > diff --git a/arch/arm/mach-shmobile/board-lager.c > b/arch/arm/mach-shmobile/board-lager.c index 6a1ba38..4d1b42b 100644 > --- a/arch/arm/mach-shmobile/board-lager.c > +++ b/arch/arm/mach-shmobile/board-lager.c > @@ -18,7 +18,10 @@ > * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 > USA */ > > +#include <linux/gpio.h> > +#include <linux/gpio_keys.h> > #include <linux/interrupt.h> > +#include <linux/input.h> My dictionary lists input before interrupt :-) > #include <linux/irqchip.h> > #include <linux/kernel.h> > #include <linux/leds.h> > @@ -52,6 +55,22 @@ static struct gpio_led_platform_data lager_leds_pdata = { > .num_leds = ARRAY_SIZE(lager_leds), > }; > > +/* GPIO KEY */ > +#define GPIO_KEY(c, g, d, ...) \ > + { .code = c, .gpio = g, .desc = d, .active_low = 1 } > + > +static struct gpio_keys_button gpio_buttons[] = { > + GPIO_KEY(KEY_4, RCAR_GP_PIN(1, 28), "SW2-pin4"), > + GPIO_KEY(KEY_3, RCAR_GP_PIN(1, 26), "SW2-pin3"), > + GPIO_KEY(KEY_2, RCAR_GP_PIN(1, 24), "SW2-pin2"), > + GPIO_KEY(KEY_1, RCAR_GP_PIN(1, 14), "SW2-pin1"), > +}; > + > +static struct gpio_keys_platform_data lager_keys_pdata = { > + .buttons = gpio_buttons, > + .nbuttons = ARRAY_SIZE(gpio_buttons), > +}; > + Could you please also update the lager dts file ? > static const struct pinctrl_map lager_pinctrl_map[] = { > /* SCIF0 (CN19: DEBUG SERIAL0) */ > PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7790", > @@ -73,6 +92,9 @@ static void __init lager_add_standard_devices(void) > platform_device_register_data(&platform_bus, "leds-gpio", -1, > &lager_leds_pdata, > sizeof(lager_leds_pdata)); > + platform_device_register_data(&platform_bus, "gpio-keys", -1, > + &lager_keys_pdata, > + sizeof(lager_keys_pdata)); > } > > static const char *lager_boards_compat_dt[] __initdata = {
On Tue, May 14, 2013 at 12:35:20AM +0200, Laurent Pinchart wrote: > Hi Simon, > > Thank you for the patch. > > On Monday 13 May 2013 17:53:53 Simon Horman wrote: > > The lager board has pins 1 - 4 of SW2 wired up to GPIO pins. > > This patch allows access to those pins as KEYS 1 - 4 using > > gpio-keys. > > > > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > > > --- > > > > This patch has run time dependencies on > > 1. "gpio-rcar: Add support for IRQ_TYPE_EDGE_BOTH" > > 2. "ARM: shmobile: r8a7790: Configure R-Car GPIO for IRQ_TYPE_EDGE_BOTH" > > > > Without those dependencies satisfied the gpio-keys driver will > > fail to be initialise itself. The boot should be otherwise successful > > and the board otherwise functional. > > --- > > arch/arm/mach-shmobile/board-lager.c | 22 ++++++++++++++++++++++ > > 1 file changed, 22 insertions(+) > > > > diff --git a/arch/arm/mach-shmobile/board-lager.c > > b/arch/arm/mach-shmobile/board-lager.c index 6a1ba38..4d1b42b 100644 > > --- a/arch/arm/mach-shmobile/board-lager.c > > +++ b/arch/arm/mach-shmobile/board-lager.c > > @@ -18,7 +18,10 @@ > > * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 > > USA */ > > > > +#include <linux/gpio.h> > > +#include <linux/gpio_keys.h> > > #include <linux/interrupt.h> > > +#include <linux/input.h> > > My dictionary lists input before interrupt :-) Thanks, I will fix that. > > #include <linux/irqchip.h> > > #include <linux/kernel.h> > > #include <linux/leds.h> > > @@ -52,6 +55,22 @@ static struct gpio_led_platform_data lager_leds_pdata = { > > .num_leds = ARRAY_SIZE(lager_leds), > > }; > > > > +/* GPIO KEY */ > > +#define GPIO_KEY(c, g, d, ...) \ > > + { .code = c, .gpio = g, .desc = d, .active_low = 1 } > > + > > +static struct gpio_keys_button gpio_buttons[] = { > > + GPIO_KEY(KEY_4, RCAR_GP_PIN(1, 28), "SW2-pin4"), > > + GPIO_KEY(KEY_3, RCAR_GP_PIN(1, 26), "SW2-pin3"), > > + GPIO_KEY(KEY_2, RCAR_GP_PIN(1, 24), "SW2-pin2"), > > + GPIO_KEY(KEY_1, RCAR_GP_PIN(1, 14), "SW2-pin1"), > > +}; > > + > > +static struct gpio_keys_platform_data lager_keys_pdata = { > > + .buttons = gpio_buttons, > > + .nbuttons = ARRAY_SIZE(gpio_buttons), > > +}; > > + > > Could you please also update the lager dts file ? I wonder if in that case we can remove the C code above. And probably the C code for the GPIO leds too. Magnus, could you clarify how you would like C-code and DTS to look on the lager board? > > static const struct pinctrl_map lager_pinctrl_map[] = { > > /* SCIF0 (CN19: DEBUG SERIAL0) */ > > PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7790", > > @@ -73,6 +92,9 @@ static void __init lager_add_standard_devices(void) > > platform_device_register_data(&platform_bus, "leds-gpio", -1, > > &lager_leds_pdata, > > sizeof(lager_leds_pdata)); > > + platform_device_register_data(&platform_bus, "gpio-keys", -1, > > + &lager_keys_pdata, > > + sizeof(lager_keys_pdata)); > > } > > > > static const char *lager_boards_compat_dt[] __initdata = {
Hi Simon and Laurent, On Tue, May 14, 2013 at 11:59 AM, Simon Horman <horms@verge.net.au> wrote: > On Tue, May 14, 2013 at 12:35:20AM +0200, Laurent Pinchart wrote: >> Hi Simon, >> >> Thank you for the patch. >> >> On Monday 13 May 2013 17:53:53 Simon Horman wrote: >> > The lager board has pins 1 - 4 of SW2 wired up to GPIO pins. >> > This patch allows access to those pins as KEYS 1 - 4 using >> > gpio-keys. >> > >> > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> >> > >> > --- >> > >> > This patch has run time dependencies on >> > 1. "gpio-rcar: Add support for IRQ_TYPE_EDGE_BOTH" >> > 2. "ARM: shmobile: r8a7790: Configure R-Car GPIO for IRQ_TYPE_EDGE_BOTH" >> > >> > Without those dependencies satisfied the gpio-keys driver will >> > fail to be initialise itself. The boot should be otherwise successful >> > and the board otherwise functional. >> > --- >> > arch/arm/mach-shmobile/board-lager.c | 22 ++++++++++++++++++++++ >> > 1 file changed, 22 insertions(+) >> > >> > diff --git a/arch/arm/mach-shmobile/board-lager.c >> > b/arch/arm/mach-shmobile/board-lager.c index 6a1ba38..4d1b42b 100644 >> > --- a/arch/arm/mach-shmobile/board-lager.c >> > +++ b/arch/arm/mach-shmobile/board-lager.c >> > @@ -18,7 +18,10 @@ >> > * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 >> > USA */ >> > >> > +#include <linux/gpio.h> >> > +#include <linux/gpio_keys.h> >> > #include <linux/interrupt.h> >> > +#include <linux/input.h> >> >> My dictionary lists input before interrupt :-) > > Thanks, I will fix that. > >> > #include <linux/irqchip.h> >> > #include <linux/kernel.h> >> > #include <linux/leds.h> >> > @@ -52,6 +55,22 @@ static struct gpio_led_platform_data lager_leds_pdata = { >> > .num_leds = ARRAY_SIZE(lager_leds), >> > }; >> > >> > +/* GPIO KEY */ >> > +#define GPIO_KEY(c, g, d, ...) \ >> > + { .code = c, .gpio = g, .desc = d, .active_low = 1 } >> > + >> > +static struct gpio_keys_button gpio_buttons[] = { >> > + GPIO_KEY(KEY_4, RCAR_GP_PIN(1, 28), "SW2-pin4"), >> > + GPIO_KEY(KEY_3, RCAR_GP_PIN(1, 26), "SW2-pin3"), >> > + GPIO_KEY(KEY_2, RCAR_GP_PIN(1, 24), "SW2-pin2"), >> > + GPIO_KEY(KEY_1, RCAR_GP_PIN(1, 14), "SW2-pin1"), >> > +}; >> > + >> > +static struct gpio_keys_platform_data lager_keys_pdata = { >> > + .buttons = gpio_buttons, >> > + .nbuttons = ARRAY_SIZE(gpio_buttons), >> > +}; >> > + >> >> Could you please also update the lager dts file ? > > I wonder if in that case we can remove the C code above. > And probably the C code for the GPIO leds too. > > Magnus, could you clarify how you would like > C-code and DTS to look on the lager board? I'd like C and DTS to coexist in parallel until we can ditch C fully. I believe there is a need for us to be able to back port the C code. For the future we want to use DTS. To support DTS for Lager I think you should create a -reference DTS file for Lager where you put the DT version of your GPIO LED / switch code. At the time when we can configure the PFC via PINCTRL DT then I believe we should be able to replace most of the platform device code with DT versions. At that we should hopefully be able to ditch all the C board code, or maybe we need to keep some around until we have the common clocks going... Thanks, / magnus
On Tue, May 14, 2013 at 03:09:08PM +0900, Magnus Damm wrote: > Hi Simon and Laurent, > > On Tue, May 14, 2013 at 11:59 AM, Simon Horman <horms@verge.net.au> wrote: > > On Tue, May 14, 2013 at 12:35:20AM +0200, Laurent Pinchart wrote: > >> Hi Simon, > >> > >> Thank you for the patch. > >> > >> On Monday 13 May 2013 17:53:53 Simon Horman wrote: > >> > The lager board has pins 1 - 4 of SW2 wired up to GPIO pins. > >> > This patch allows access to those pins as KEYS 1 - 4 using > >> > gpio-keys. > >> > > >> > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > >> > > >> > --- > >> > > >> > This patch has run time dependencies on > >> > 1. "gpio-rcar: Add support for IRQ_TYPE_EDGE_BOTH" > >> > 2. "ARM: shmobile: r8a7790: Configure R-Car GPIO for IRQ_TYPE_EDGE_BOTH" > >> > > >> > Without those dependencies satisfied the gpio-keys driver will > >> > fail to be initialise itself. The boot should be otherwise successful > >> > and the board otherwise functional. > >> > --- > >> > arch/arm/mach-shmobile/board-lager.c | 22 ++++++++++++++++++++++ > >> > 1 file changed, 22 insertions(+) > >> > > >> > diff --git a/arch/arm/mach-shmobile/board-lager.c > >> > b/arch/arm/mach-shmobile/board-lager.c index 6a1ba38..4d1b42b 100644 > >> > --- a/arch/arm/mach-shmobile/board-lager.c > >> > +++ b/arch/arm/mach-shmobile/board-lager.c > >> > @@ -18,7 +18,10 @@ > >> > * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 > >> > USA */ > >> > > >> > +#include <linux/gpio.h> > >> > +#include <linux/gpio_keys.h> > >> > #include <linux/interrupt.h> > >> > +#include <linux/input.h> > >> > >> My dictionary lists input before interrupt :-) > > > > Thanks, I will fix that. > > > >> > #include <linux/irqchip.h> > >> > #include <linux/kernel.h> > >> > #include <linux/leds.h> > >> > @@ -52,6 +55,22 @@ static struct gpio_led_platform_data lager_leds_pdata = { > >> > .num_leds = ARRAY_SIZE(lager_leds), > >> > }; > >> > > >> > +/* GPIO KEY */ > >> > +#define GPIO_KEY(c, g, d, ...) \ > >> > + { .code = c, .gpio = g, .desc = d, .active_low = 1 } > >> > + > >> > +static struct gpio_keys_button gpio_buttons[] = { > >> > + GPIO_KEY(KEY_4, RCAR_GP_PIN(1, 28), "SW2-pin4"), > >> > + GPIO_KEY(KEY_3, RCAR_GP_PIN(1, 26), "SW2-pin3"), > >> > + GPIO_KEY(KEY_2, RCAR_GP_PIN(1, 24), "SW2-pin2"), > >> > + GPIO_KEY(KEY_1, RCAR_GP_PIN(1, 14), "SW2-pin1"), > >> > +}; > >> > + > >> > +static struct gpio_keys_platform_data lager_keys_pdata = { > >> > + .buttons = gpio_buttons, > >> > + .nbuttons = ARRAY_SIZE(gpio_buttons), > >> > +}; > >> > + > >> > >> Could you please also update the lager dts file ? > > > > I wonder if in that case we can remove the C code above. > > And probably the C code for the GPIO leds too. > > > > Magnus, could you clarify how you would like > > C-code and DTS to look on the lager board? > > I'd like C and DTS to coexist in parallel until we can ditch C fully. > I believe there is a need for us to be able to back port the C code. > For the future we want to use DTS. > > To support DTS for Lager I think you should create a -reference DTS > file for Lager where you put the DT version of your GPIO LED / switch > code. At the time when we can configure the PFC via PINCTRL DT then I > believe we should be able to replace most of the platform device code > with DT versions. At that we should hopefully be able to ditch all the > C board code, or maybe we need to keep some around until we have the > common clocks going... Hi Magnus, thanks for the clarification. That all sounds reasonable and I will see about making it so.
Hi Magnus, On Tuesday 14 May 2013 15:09:08 Magnus Damm wrote: > On Tue, May 14, 2013 at 11:59 AM, Simon Horman <horms@verge.net.au> wrote: > > On Tue, May 14, 2013 at 12:35:20AM +0200, Laurent Pinchart wrote: > >> On Monday 13 May 2013 17:53:53 Simon Horman wrote: > >> > The lager board has pins 1 - 4 of SW2 wired up to GPIO pins. > >> > This patch allows access to those pins as KEYS 1 - 4 using > >> > gpio-keys. > >> > > >> > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > >> > > >> > --- > >> > > >> > This patch has run time dependencies on > >> > 1. "gpio-rcar: Add support for IRQ_TYPE_EDGE_BOTH" > >> > 2. "ARM: shmobile: r8a7790: Configure R-Car GPIO for > >> > IRQ_TYPE_EDGE_BOTH" > >> > > >> > Without those dependencies satisfied the gpio-keys driver will > >> > fail to be initialise itself. The boot should be otherwise successful > >> > and the board otherwise functional. > >> > --- > >> > > >> > arch/arm/mach-shmobile/board-lager.c | 22 ++++++++++++++++++++++ > >> > 1 file changed, 22 insertions(+) > >> > > >> > diff --git a/arch/arm/mach-shmobile/board-lager.c > >> > b/arch/arm/mach-shmobile/board-lager.c index 6a1ba38..4d1b42b 100644 > >> > --- a/arch/arm/mach-shmobile/board-lager.c > >> > +++ b/arch/arm/mach-shmobile/board-lager.c > >> > @@ -18,7 +18,10 @@ > >> > > >> > * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA > >> > 02110-1301 > >> > > >> > USA */ > >> > > >> > +#include <linux/gpio.h> > >> > +#include <linux/gpio_keys.h> > >> > > >> > #include <linux/interrupt.h> > >> > > >> > +#include <linux/input.h> > >> > >> My dictionary lists input before interrupt :-) > > > > Thanks, I will fix that. > > > >> > #include <linux/irqchip.h> > >> > #include <linux/kernel.h> > >> > #include <linux/leds.h> > >> > > >> > @@ -52,6 +55,22 @@ static struct gpio_led_platform_data > >> > lager_leds_pdata = { .num_leds = ARRAY_SIZE(lager_leds), > >> > > >> > }; > >> > > >> > +/* GPIO KEY */ > >> > +#define GPIO_KEY(c, g, d, ...) \ > >> > + { .code = c, .gpio = g, .desc = d, .active_low = 1 } > >> > + > >> > +static struct gpio_keys_button gpio_buttons[] = { > >> > + GPIO_KEY(KEY_4, RCAR_GP_PIN(1, 28), "SW2-pin4"), > >> > + GPIO_KEY(KEY_3, RCAR_GP_PIN(1, 26), "SW2-pin3"), > >> > + GPIO_KEY(KEY_2, RCAR_GP_PIN(1, 24), "SW2-pin2"), > >> > + GPIO_KEY(KEY_1, RCAR_GP_PIN(1, 14), "SW2-pin1"), > >> > +}; > >> > + > >> > +static struct gpio_keys_platform_data lager_keys_pdata = { > >> > + .buttons = gpio_buttons, > >> > + .nbuttons = ARRAY_SIZE(gpio_buttons), > >> > +}; > >> > + > >> > >> Could you please also update the lager dts file ? > > > > I wonder if in that case we can remove the C code above. > > And probably the C code for the GPIO leds too. > > > > Magnus, could you clarify how you would like > > C-code and DTS to look on the lager board? > > I'd like C and DTS to coexist in parallel until we can ditch C fully. > I believe there is a need for us to be able to back port the C code. > For the future we want to use DTS. > > To support DTS for Lager I think you should create a -reference DTS > file for Lager where you put the DT version of your GPIO LED / switch > code. At the time when we can configure the PFC via PINCTRL DT then I > believe we should be able to replace most of the platform device code > with DT versions. I've sent an RFC for gpio-rcar DT bindings, and I'll send one for sh-pfc in the next few days. DT support for GPIO and PINCTRL should then hopefully be available very soon. > At that we should hopefully be able to ditch all the C board code, Will we also ditch non-reference board files ? > or maybe we need to keep some around until we have the common clocks > going... What's the status of CCF support development in sh-mobile ?
diff --git a/arch/arm/mach-shmobile/board-lager.c b/arch/arm/mach-shmobile/board-lager.c index 6a1ba38..4d1b42b 100644 --- a/arch/arm/mach-shmobile/board-lager.c +++ b/arch/arm/mach-shmobile/board-lager.c @@ -18,7 +18,10 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ +#include <linux/gpio.h> +#include <linux/gpio_keys.h> #include <linux/interrupt.h> +#include <linux/input.h> #include <linux/irqchip.h> #include <linux/kernel.h> #include <linux/leds.h> @@ -52,6 +55,22 @@ static struct gpio_led_platform_data lager_leds_pdata = { .num_leds = ARRAY_SIZE(lager_leds), }; +/* GPIO KEY */ +#define GPIO_KEY(c, g, d, ...) \ + { .code = c, .gpio = g, .desc = d, .active_low = 1 } + +static struct gpio_keys_button gpio_buttons[] = { + GPIO_KEY(KEY_4, RCAR_GP_PIN(1, 28), "SW2-pin4"), + GPIO_KEY(KEY_3, RCAR_GP_PIN(1, 26), "SW2-pin3"), + GPIO_KEY(KEY_2, RCAR_GP_PIN(1, 24), "SW2-pin2"), + GPIO_KEY(KEY_1, RCAR_GP_PIN(1, 14), "SW2-pin1"), +}; + +static struct gpio_keys_platform_data lager_keys_pdata = { + .buttons = gpio_buttons, + .nbuttons = ARRAY_SIZE(gpio_buttons), +}; + static const struct pinctrl_map lager_pinctrl_map[] = { /* SCIF0 (CN19: DEBUG SERIAL0) */ PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7790", @@ -73,6 +92,9 @@ static void __init lager_add_standard_devices(void) platform_device_register_data(&platform_bus, "leds-gpio", -1, &lager_leds_pdata, sizeof(lager_leds_pdata)); + platform_device_register_data(&platform_bus, "gpio-keys", -1, + &lager_keys_pdata, + sizeof(lager_keys_pdata)); } static const char *lager_boards_compat_dt[] __initdata = {
The lager board has pins 1 - 4 of SW2 wired up to GPIO pins. This patch allows access to those pins as KEYS 1 - 4 using gpio-keys. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> --- This patch has run time dependencies on 1. "gpio-rcar: Add support for IRQ_TYPE_EDGE_BOTH" 2. "ARM: shmobile: r8a7790: Configure R-Car GPIO for IRQ_TYPE_EDGE_BOTH" Without those dependencies satisfied the gpio-keys driver will fail to be initialise itself. The boot should be otherwise successful and the board otherwise functional. --- arch/arm/mach-shmobile/board-lager.c | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)