@@ -105,6 +105,8 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx27-pdk.dtb \
imx27-phytec-phycore-som.dtb \
imx27-phytec-phycore-rdk.dtb \
+ imx27-phytec-phycard-s-som.dtb \
+ imx27-phytec-phycard-s-rdk.dtb \
imx31-bug.dtb \
imx51-apf51.dtb \
imx51-apf51dev.dtb \
new file mode 100644
@@ -0,0 +1,62 @@
+/*
+ * Copyright 2012 Markus Pargmann, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "imx27-phytec-phycard-s-som.dts"
+
+/ {
+ model = "Phytec pca100 rapid development kit";
+ compatible = "phytec,imx27-pca100-rdk", "phytec,imx27-pca100", "fsl,imx27";
+
+ display: display {
+ model = "Primeview-PD050VL1";
+ native-mode = <&timing0>;
+ bits-per-pixel = <16>; /* non-standard but required */
+ fsl,pcr = <0xf0c88080>; /* non-standard but required */
+ display-timings {
+ timing0: 640x480 {
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <112>;
+ hfront-porch = <36>;
+ hsync-len = <32>;
+ vback-porch = <33>;
+ vfront-porch = <33>;
+ vsync-len = <2>;
+ clock-frequency = <25000000>;
+ };
+ };
+ };
+};
+
+&imxfb {
+ display = <&display>;
+ status = "okay";
+};
+
+&sdhci2 {
+ cd-gpios = <&gpio3 29 0>;
+ status = "okay";
+};
+
+&uart1 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart2 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart3 {
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,72 @@
+/*
+ * Copyright 2012 Sascha Hauer, Uwe Kleine-König, Steffen Trumtrar
+ * and Markus Pargmann, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx27.dtsi"
+
+/ {
+ model = "Phytec pca100";
+ compatible = "phytec,imx27-pca100", "fsl,imx27";
+
+ memory {
+ reg = <0x0 0x08000000>; /* 128MB */
+ };
+};
+
+&cspi1 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio4 28 0>,
+ <&gpio4 27 0>;
+ status = "okay";
+};
+
+&fec {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ ioexpander@41 {
+ compatible = "nxp,pca9536";
+ reg = <0x41>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ lm75@4a {
+ compatible = "national,lm75";
+ reg = <0x4a>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ at24@52 {
+ compatible = "at,24c32";
+ pagesize = <32>;
+ reg = <0x52>;
+ };
+};
+
+&owire {
+ status = "okay";
+};
Board files for Phytec PhyCARD-S "System on Module" and "Rapid Development Kit". Based on patches from: Steffen Trumtrar <s.trumtrar@pengutronix.de>: - Original patch - ARM: dts: Set partition offsets for phycard - ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100 - ARM: imx27-phytec-phycard-S.dts: resize nand partitions Jan Luebbe <jlu@pengutronix.de>: - ARM: dts: Enable bad block table in NAND Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de> Cc: Jan Luebbe <jlu@pengutronix.de> Signed-off-by: Markus Pargmann <mpa@pengutronix.de> --- Notes: Changes in v2: - Remove unnecessary Kconfig nand selection. - Style fixes - Replace node identifiers with node labels - Fix compatibility of cpu node - Remove device node for not mainlined dimmer driver - Remove nand partition table - Remove memory node - Splitted board file into "system on module" and "rapid development kit" arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts | 62 ++++++++++++++++++++ arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts | 72 ++++++++++++++++++++++++ 3 files changed, 136 insertions(+) create mode 100644 arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts create mode 100644 arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts