Message ID | 1375825216-18119-1-git-send-email-s-anna@ti.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On Aug 6, 2013, at 4:40 PM, Suman Anna wrote: > Logic has been added to the OMAP2+ mailbox code to > parse the mailbox dt nodes and construct the different > mailboxes associated with the instance. The design is > based on gathering the same information that was being > passed previously through the platform data, except for > the interrupt type configuration information. > > Signed-off-by: Suman Anna <s-anna@ti.com> > --- > .../devicetree/bindings/mailbox/omap-mailbox.txt | 43 +++++++ > drivers/mailbox/mailbox-omap2.c | 130 ++++++++++++++++++--- > 2 files changed, 158 insertions(+), 15 deletions(-) > create mode 100644 Documentation/devicetree/bindings/mailbox/omap-mailbox.txt > > diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt > new file mode 100644 > index 0000000..8ffb08a > --- /dev/null > +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt > @@ -0,0 +1,43 @@ > +OMAP2+ Mailbox Driver > + > +Required properties: > +- compatible: Should be one of the following, > + "ti,omap2-mailbox" for > + OMAP2420, OMAP2430, OMAP3430, OMAP3630 SoCs > + "ti,omap4-mailbox" for > + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs > +- reg: Contains the mailbox register address range (base address > + and length) > +- interrupts: Contains the interrupt information for the mailbox > + device. The format is dependent on which interrupt > + controller the OMAP device uses > +- ti,hwmods: Name of the hwmod associated with the mailbox > +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox device > + can interrupt > +- ti,mbox-num-fifos: Number of h/w fifos within the mailbox device Isn't "ti,mbox-num-users", "ti,mbox-num-fifos" this SoC specific, why do we need to encode in the device tree. Can we not have a more SoC specific compatiable and encode such info in the driver as part of the .data field in of_device_id ? > +- ti,mbox-names: Array of the names of the mailboxes > +- ti,mbox-data: Mailbox descriptor data private to each mailbox. The 4 > + cells represent the following data, > + Cell #1 (tx_id) - mailbox fifo id used for > + transmitting messages > + Cell #2 (rx_id) - mailbox fifo id on which messages > + are received > + Cell #3 (irq_id) - irq identifier index number to use > + from the interrupts data > + Cell #4 (usr_id) - mailbox user id for identifying the > + interrupt into the MPU interrupt > + controller. > + ti,mbox-data really seems like it should be encoded in the driver and not in the device tree. Is it specific to the SoC? > +Example: > + > +/* OMAP4 */ > +mailbox: mailbox@4a0f4000 { > + compatible = "ti,omap4-mailbox"; > + reg = <0x4a0f4000 0x200>; > + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; > + ti,hwmods = "mailbox"; > + ti,mbox-num-users = <3>; > + ti,mbox-num-fifos = <8>; > + ti,mbox-names = "mbox-ipu", "mbox-dsp"; > + ti,mbox-data = <0 1 0 0>, <3 2 0 0>; > +}; [snip] - k -- Employee of Qualcomm Innovation Center, Inc. Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Kumar, >> Logic has been added to the OMAP2+ mailbox code to >> parse the mailbox dt nodes and construct the different >> mailboxes associated with the instance. The design is >> based on gathering the same information that was being >> passed previously through the platform data, except for >> the interrupt type configuration information. >> >> Signed-off-by: Suman Anna <s-anna@ti.com> >> --- >> .../devicetree/bindings/mailbox/omap-mailbox.txt | 43 +++++++ >> drivers/mailbox/mailbox-omap2.c | 130 ++++++++++++++++++--- >> 2 files changed, 158 insertions(+), 15 deletions(-) >> create mode 100644 Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >> >> diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >> new file mode 100644 >> index 0000000..8ffb08a >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >> @@ -0,0 +1,43 @@ >> +OMAP2+ Mailbox Driver >> + >> +Required properties: >> +- compatible: Should be one of the following, >> + "ti,omap2-mailbox" for >> + OMAP2420, OMAP2430, OMAP3430, OMAP3630 SoCs >> + "ti,omap4-mailbox" for >> + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs >> +- reg: Contains the mailbox register address range (base address >> + and length) >> +- interrupts: Contains the interrupt information for the mailbox >> + device. The format is dependent on which interrupt >> + controller the OMAP device uses >> +- ti,hwmods: Name of the hwmod associated with the mailbox >> +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox device >> + can interrupt >> +- ti,mbox-num-fifos: Number of h/w fifos within the mailbox device > > Isn't "ti,mbox-num-users", "ti,mbox-num-fifos" this SoC specific, why do we need to encode in the device tree. Can we not have a more SoC specific compatiable and encode such info in the driver as part of the .data field in of_device_id ? They are IP design parameters for the number of h/w fifos and interrupts coming out of the IP block, with the functionality identical. This information could not be read from any registers. Until OMAP5, we always had a single IP in the SoC and so these could been encoded in the driver. But in DRA7xx, a new SoC, we have 13 mailboxes which have differing number of these properties even though the functional IP block is same. > >> +- ti,mbox-names: Array of the names of the mailboxes >> +- ti,mbox-data: Mailbox descriptor data private to each mailbox. The 4 >> + cells represent the following data, >> + Cell #1 (tx_id) - mailbox fifo id used for >> + transmitting messages >> + Cell #2 (rx_id) - mailbox fifo id on which messages >> + are received >> + Cell #3 (irq_id) - irq identifier index number to use >> + from the interrupts data >> + Cell #4 (usr_id) - mailbox user id for identifying the >> + interrupt into the MPU interrupt >> + controller. >> + > > ti,mbox-data really seems like it should be encoded in the driver and not in the device tree. Is it specific to the SoC? The mbox-data represents the assignment of h/w fifos between a pair of processors on an SoC, so it is specific to a mailbox IP instance in an SoC. Also, this assignment makes it flexible for anyone wishing to use their own firmware/stack on the remote processor side if using different h/w fifo combination. So, a single SoC-specific compatible string would not be enough to identify either of the above data in the driver. regards Suman > >> +Example: >> + >> +/* OMAP4 */ >> +mailbox: mailbox@4a0f4000 { >> + compatible = "ti,omap4-mailbox"; >> + reg = <0x4a0f4000 0x200>; >> + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; >> + ti,hwmods = "mailbox"; >> + ti,mbox-num-users = <3>; >> + ti,mbox-num-fifos = <8>; >> + ti,mbox-names = "mbox-ipu", "mbox-dsp"; >> + ti,mbox-data = <0 1 0 0>, <3 2 0 0>; >> +}; > > [snip] > > - k > > -- > Employee of Qualcomm Innovation Center, Inc. > Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Aug 7, 2013, at 11:59 AM, Suman Anna wrote: > Kumar, > >>> Logic has been added to the OMAP2+ mailbox code to >>> parse the mailbox dt nodes and construct the different >>> mailboxes associated with the instance. The design is >>> based on gathering the same information that was being >>> passed previously through the platform data, except for >>> the interrupt type configuration information. >>> >>> Signed-off-by: Suman Anna <s-anna@ti.com> >>> --- >>> .../devicetree/bindings/mailbox/omap-mailbox.txt | 43 +++++++ >>> drivers/mailbox/mailbox-omap2.c | 130 ++++++++++++++++++--- >>> 2 files changed, 158 insertions(+), 15 deletions(-) >>> create mode 100644 Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>> >>> diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>> new file mode 100644 >>> index 0000000..8ffb08a >>> --- /dev/null >>> +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>> @@ -0,0 +1,43 @@ >>> +OMAP2+ Mailbox Driver >>> + >>> +Required properties: >>> +- compatible: Should be one of the following, >>> + "ti,omap2-mailbox" for >>> + OMAP2420, OMAP2430, OMAP3430, OMAP3630 SoCs >>> + "ti,omap4-mailbox" for >>> + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs >>> +- reg: Contains the mailbox register address range (base address >>> + and length) >>> +- interrupts: Contains the interrupt information for the mailbox >>> + device. The format is dependent on which interrupt >>> + controller the OMAP device uses >>> +- ti,hwmods: Name of the hwmod associated with the mailbox >>> +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox device >>> + can interrupt >>> +- ti,mbox-num-fifos: Number of h/w fifos within the mailbox device >> >> Isn't "ti,mbox-num-users", "ti,mbox-num-fifos" this SoC specific, why do we need to encode in the device tree. Can we not have a more SoC specific compatiable and encode such info in the driver as part of the .data field in of_device_id ? > > They are IP design parameters for the number of h/w fifos and interrupts > coming out of the IP block, with the functionality identical. This > information could not be read from any registers. Until OMAP5, we always > had a single IP in the SoC and so these could been encoded in the > driver. But in DRA7xx, a new SoC, we have 13 mailboxes which have > differing number of these properties even though the functional IP block > is same. Ah, I see. Since you've got examples of the same IP with different design params in a given SoC than this makes sense. Is that true of ti,mbox-num-users? >>> +- ti,mbox-names: Array of the names of the mailboxes >>> +- ti,mbox-data: Mailbox descriptor data private to each mailbox. The 4 >>> + cells represent the following data, >>> + Cell #1 (tx_id) - mailbox fifo id used for >>> + transmitting messages >>> + Cell #2 (rx_id) - mailbox fifo id on which messages >>> + are received >>> + Cell #3 (irq_id) - irq identifier index number to use >>> + from the interrupts data >>> + Cell #4 (usr_id) - mailbox user id for identifying the >>> + interrupt into the MPU interrupt >>> + controller. >>> + >> >> ti,mbox-data really seems like it should be encoded in the driver and not in the device tree. Is it specific to the SoC? > > The mbox-data represents the assignment of h/w fifos between a pair of > processors on an SoC, so it is specific to a mailbox IP instance in an > SoC. Also, this assignment makes it flexible for anyone wishing to use > their own firmware/stack on the remote processor side if using different > h/w fifo combination. > > So, a single SoC-specific compatible string would not be enough to > identify either of the above data in the driver. ok - k > > regards > Suman > >> >>> +Example: >>> + >>> +/* OMAP4 */ >>> +mailbox: mailbox@4a0f4000 { >>> + compatible = "ti,omap4-mailbox"; >>> + reg = <0x4a0f4000 0x200>; >>> + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; >>> + ti,hwmods = "mailbox"; >>> + ti,mbox-num-users = <3>; >>> + ti,mbox-num-fifos = <8>; >>> + ti,mbox-names = "mbox-ipu", "mbox-dsp"; >>> + ti,mbox-data = <0 1 0 0>, <3 2 0 0>; >>> +}; >> >> [snip] >> >> - k >> >> -- >> Employee of Qualcomm Innovation Center, Inc. >> Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation >> > -- Employee of Qualcomm Innovation Center, Inc. Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 08/07/2013 12:41 PM, Kumar Gala wrote: > > On Aug 7, 2013, at 11:59 AM, Suman Anna wrote: > >> Kumar, >> >>>> Logic has been added to the OMAP2+ mailbox code to >>>> parse the mailbox dt nodes and construct the different >>>> mailboxes associated with the instance. The design is >>>> based on gathering the same information that was being >>>> passed previously through the platform data, except for >>>> the interrupt type configuration information. >>>> >>>> Signed-off-by: Suman Anna <s-anna@ti.com> >>>> --- >>>> .../devicetree/bindings/mailbox/omap-mailbox.txt | 43 +++++++ >>>> drivers/mailbox/mailbox-omap2.c | 130 ++++++++++++++++++--- >>>> 2 files changed, 158 insertions(+), 15 deletions(-) >>>> create mode 100644 Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>> >>>> diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>> new file mode 100644 >>>> index 0000000..8ffb08a >>>> --- /dev/null >>>> +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>> @@ -0,0 +1,43 @@ >>>> +OMAP2+ Mailbox Driver >>>> + >>>> +Required properties: >>>> +- compatible: Should be one of the following, >>>> + "ti,omap2-mailbox" for >>>> + OMAP2420, OMAP2430, OMAP3430, OMAP3630 SoCs >>>> + "ti,omap4-mailbox" for >>>> + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs >>>> +- reg: Contains the mailbox register address range (base address >>>> + and length) >>>> +- interrupts: Contains the interrupt information for the mailbox >>>> + device. The format is dependent on which interrupt >>>> + controller the OMAP device uses >>>> +- ti,hwmods: Name of the hwmod associated with the mailbox >>>> +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox device >>>> + can interrupt >>>> +- ti,mbox-num-fifos: Number of h/w fifos within the mailbox device >>> >>> Isn't "ti,mbox-num-users", "ti,mbox-num-fifos" this SoC specific, why do we need to encode in the device tree. Can we not have a more SoC specific compatiable and encode such info in the driver as part of the .data field in of_device_id ? >> >> They are IP design parameters for the number of h/w fifos and interrupts >> coming out of the IP block, with the functionality identical. This >> information could not be read from any registers. Until OMAP5, we always >> had a single IP in the SoC and so these could been encoded in the >> driver. But in DRA7xx, a new SoC, we have 13 mailboxes which have >> differing number of these properties even though the functional IP block >> is same. > > Ah, I see. Since you've got examples of the same IP with different design params in a given SoC than this makes sense. > > Is that true of ti,mbox-num-users? Yes, it is true of both "ti,mbox-num-users" and "ti,mbox-num-fifos". regards Suman > >>>> +- ti,mbox-names: Array of the names of the mailboxes >>>> +- ti,mbox-data: Mailbox descriptor data private to each mailbox. The 4 >>>> + cells represent the following data, >>>> + Cell #1 (tx_id) - mailbox fifo id used for >>>> + transmitting messages >>>> + Cell #2 (rx_id) - mailbox fifo id on which messages >>>> + are received >>>> + Cell #3 (irq_id) - irq identifier index number to use >>>> + from the interrupts data >>>> + Cell #4 (usr_id) - mailbox user id for identifying the >>>> + interrupt into the MPU interrupt >>>> + controller. >>>> + >>> >>> ti,mbox-data really seems like it should be encoded in the driver and not in the device tree. Is it specific to the SoC? >> >> The mbox-data represents the assignment of h/w fifos between a pair of >> processors on an SoC, so it is specific to a mailbox IP instance in an >> SoC. Also, this assignment makes it flexible for anyone wishing to use >> their own firmware/stack on the remote processor side if using different >> h/w fifo combination. >> >> So, a single SoC-specific compatible string would not be enough to >> identify either of the above data in the driver. > > ok > > - k > >> >> regards >> Suman >> >>> >>>> +Example: >>>> + >>>> +/* OMAP4 */ >>>> +mailbox: mailbox@4a0f4000 { >>>> + compatible = "ti,omap4-mailbox"; >>>> + reg = <0x4a0f4000 0x200>; >>>> + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; >>>> + ti,hwmods = "mailbox"; >>>> + ti,mbox-num-users = <3>; >>>> + ti,mbox-num-fifos = <8>; >>>> + ti,mbox-names = "mbox-ipu", "mbox-dsp"; >>>> + ti,mbox-data = <0 1 0 0>, <3 2 0 0>; >>>> +}; >>> >>> [snip] >>> >>> - k >>> >>> -- >>> Employee of Qualcomm Innovation Center, Inc. >>> Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation >>> >> > > -- > Employee of Qualcomm Innovation Center, Inc. > Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Aug 7, 2013, at 3:08 PM, Suman Anna wrote: > On 08/07/2013 12:41 PM, Kumar Gala wrote: >> >> On Aug 7, 2013, at 11:59 AM, Suman Anna wrote: >> >>> Kumar, >>> >>>>> Logic has been added to the OMAP2+ mailbox code to >>>>> parse the mailbox dt nodes and construct the different >>>>> mailboxes associated with the instance. The design is >>>>> based on gathering the same information that was being >>>>> passed previously through the platform data, except for >>>>> the interrupt type configuration information. >>>>> >>>>> Signed-off-by: Suman Anna <s-anna@ti.com> >>>>> --- >>>>> .../devicetree/bindings/mailbox/omap-mailbox.txt | 43 +++++++ >>>>> drivers/mailbox/mailbox-omap2.c | 130 ++++++++++++++++++--- >>>>> 2 files changed, 158 insertions(+), 15 deletions(-) >>>>> create mode 100644 Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>> >>>>> diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>> new file mode 100644 >>>>> index 0000000..8ffb08a >>>>> --- /dev/null >>>>> +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>> @@ -0,0 +1,43 @@ >>>>> +OMAP2+ Mailbox Driver >>>>> + >>>>> +Required properties: >>>>> +- compatible: Should be one of the following, >>>>> + "ti,omap2-mailbox" for >>>>> + OMAP2420, OMAP2430, OMAP3430, OMAP3630 SoCs >>>>> + "ti,omap4-mailbox" for >>>>> + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs >>>>> +- reg: Contains the mailbox register address range (base address >>>>> + and length) >>>>> +- interrupts: Contains the interrupt information for the mailbox >>>>> + device. The format is dependent on which interrupt >>>>> + controller the OMAP device uses >>>>> +- ti,hwmods: Name of the hwmod associated with the mailbox >>>>> +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox device >>>>> + can interrupt >>>>> +- ti,mbox-num-fifos: Number of h/w fifos within the mailbox device >>>> >>>> Isn't "ti,mbox-num-users", "ti,mbox-num-fifos" this SoC specific, why do we need to encode in the device tree. Can we not have a more SoC specific compatiable and encode such info in the driver as part of the .data field in of_device_id ? >>> >>> They are IP design parameters for the number of h/w fifos and interrupts >>> coming out of the IP block, with the functionality identical. This >>> information could not be read from any registers. Until OMAP5, we always >>> had a single IP in the SoC and so these could been encoded in the >>> driver. But in DRA7xx, a new SoC, we have 13 mailboxes which have >>> differing number of these properties even though the functional IP block >>> is same. >> >> Ah, I see. Since you've got examples of the same IP with different design params in a given SoC than this makes sense. >> >> Is that true of ti,mbox-num-users? > > Yes, it is true of both "ti,mbox-num-users" and "ti,mbox-num-fifos". So I think it would be good to update the binding to convey that SoCs might have multiple mbox units w/different design pararms (maybe a short blurb as part of the intro). - k -- Employee of Qualcomm Innovation Center, Inc. Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 08/08/2013 09:34 AM, Kumar Gala wrote: > > On Aug 7, 2013, at 3:08 PM, Suman Anna wrote: > >> On 08/07/2013 12:41 PM, Kumar Gala wrote: >>> >>> On Aug 7, 2013, at 11:59 AM, Suman Anna wrote: >>> >>>> Kumar, >>>> >>>>>> Logic has been added to the OMAP2+ mailbox code to >>>>>> parse the mailbox dt nodes and construct the different >>>>>> mailboxes associated with the instance. The design is >>>>>> based on gathering the same information that was being >>>>>> passed previously through the platform data, except for >>>>>> the interrupt type configuration information. >>>>>> >>>>>> Signed-off-by: Suman Anna <s-anna@ti.com> >>>>>> --- >>>>>> .../devicetree/bindings/mailbox/omap-mailbox.txt | 43 +++++++ >>>>>> drivers/mailbox/mailbox-omap2.c | 130 ++++++++++++++++++--- >>>>>> 2 files changed, 158 insertions(+), 15 deletions(-) >>>>>> create mode 100644 Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>> >>>>>> diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>> new file mode 100644 >>>>>> index 0000000..8ffb08a >>>>>> --- /dev/null >>>>>> +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>> @@ -0,0 +1,43 @@ >>>>>> +OMAP2+ Mailbox Driver >>>>>> + >>>>>> +Required properties: >>>>>> +- compatible: Should be one of the following, >>>>>> + "ti,omap2-mailbox" for >>>>>> + OMAP2420, OMAP2430, OMAP3430, OMAP3630 SoCs >>>>>> + "ti,omap4-mailbox" for >>>>>> + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs >>>>>> +- reg: Contains the mailbox register address range (base address >>>>>> + and length) >>>>>> +- interrupts: Contains the interrupt information for the mailbox >>>>>> + device. The format is dependent on which interrupt >>>>>> + controller the OMAP device uses >>>>>> +- ti,hwmods: Name of the hwmod associated with the mailbox >>>>>> +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox device >>>>>> + can interrupt >>>>>> +- ti,mbox-num-fifos: Number of h/w fifos within the mailbox device >>>>> >>>>> Isn't "ti,mbox-num-users", "ti,mbox-num-fifos" this SoC specific, why do we need to encode in the device tree. Can we not have a more SoC specific compatiable and encode such info in the driver as part of the .data field in of_device_id ? >>>> >>>> They are IP design parameters for the number of h/w fifos and interrupts >>>> coming out of the IP block, with the functionality identical. This >>>> information could not be read from any registers. Until OMAP5, we always >>>> had a single IP in the SoC and so these could been encoded in the >>>> driver. But in DRA7xx, a new SoC, we have 13 mailboxes which have >>>> differing number of these properties even though the functional IP block >>>> is same. >>> >>> Ah, I see. Since you've got examples of the same IP with different design params in a given SoC than this makes sense. >>> >>> Is that true of ti,mbox-num-users? >> >> Yes, it is true of both "ti,mbox-num-users" and "ti,mbox-num-fifos". > > So I think it would be good to update the binding to convey that SoCs might have multiple mbox units w/different design pararms (maybe a short blurb as part of the intro). Sure will do. Will wait for Benoit also to come back on this series if I need to address any further review comments. regards Suman -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Suman, On 08/08/2013 17:44, Suman Anna wrote: > On 08/08/2013 09:34 AM, Kumar Gala wrote: >> >> On Aug 7, 2013, at 3:08 PM, Suman Anna wrote: >> >>> On 08/07/2013 12:41 PM, Kumar Gala wrote: >>>> >>>> On Aug 7, 2013, at 11:59 AM, Suman Anna wrote: >>>> >>>>> Kumar, >>>>> >>>>>>> Logic has been added to the OMAP2+ mailbox code to >>>>>>> parse the mailbox dt nodes and construct the different >>>>>>> mailboxes associated with the instance. The design is >>>>>>> based on gathering the same information that was being >>>>>>> passed previously through the platform data, except for >>>>>>> the interrupt type configuration information. >>>>>>> >>>>>>> Signed-off-by: Suman Anna <s-anna@ti.com> >>>>>>> --- >>>>>>> .../devicetree/bindings/mailbox/omap-mailbox.txt | 43 +++++++ >>>>>>> drivers/mailbox/mailbox-omap2.c | 130 ++++++++++++++++++--- >>>>>>> 2 files changed, 158 insertions(+), 15 deletions(-) >>>>>>> create mode 100644 Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>>> >>>>>>> diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>>> new file mode 100644 >>>>>>> index 0000000..8ffb08a >>>>>>> --- /dev/null >>>>>>> +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>>> @@ -0,0 +1,43 @@ >>>>>>> +OMAP2+ Mailbox Driver >>>>>>> + >>>>>>> +Required properties: >>>>>>> +- compatible: Should be one of the following, >>>>>>> + "ti,omap2-mailbox" for >>>>>>> + OMAP2420, OMAP2430, OMAP3430, OMAP3630 SoCs >>>>>>> + "ti,omap4-mailbox" for >>>>>>> + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs >>>>>>> +- reg: Contains the mailbox register address range (base address >>>>>>> + and length) >>>>>>> +- interrupts: Contains the interrupt information for the mailbox >>>>>>> + device. The format is dependent on which interrupt >>>>>>> + controller the OMAP device uses >>>>>>> +- ti,hwmods: Name of the hwmod associated with the mailbox >>>>>>> +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox device >>>>>>> + can interrupt >>>>>>> +- ti,mbox-num-fifos: Number of h/w fifos within the mailbox device >>>>>> >>>>>> Isn't "ti,mbox-num-users", "ti,mbox-num-fifos" this SoC specific, why do we need to encode in the device tree. Can we not have a more SoC specific compatiable and encode such info in the driver as part of the .data field in of_device_id ? >>>>> >>>>> They are IP design parameters for the number of h/w fifos and interrupts >>>>> coming out of the IP block, with the functionality identical. This >>>>> information could not be read from any registers. Until OMAP5, we always >>>>> had a single IP in the SoC and so these could been encoded in the >>>>> driver. But in DRA7xx, a new SoC, we have 13 mailboxes which have >>>>> differing number of these properties even though the functional IP block >>>>> is same. >>>> >>>> Ah, I see. Since you've got examples of the same IP with different design params in a given SoC than this makes sense. >>>> >>>> Is that true of ti,mbox-num-users? >>> >>> Yes, it is true of both "ti,mbox-num-users" and "ti,mbox-num-fifos". >> >> So I think it would be good to update the binding to convey that SoCs might have multiple mbox units w/different design pararms (maybe a short blurb as part of the intro). > > Sure will do. Will wait for Benoit also to come back on this series if I > need to address any further review comments. I had the same concern than Kumar originally, so if nobody has anymore complain with this binding, that fine to me. At least for the DTS part. Regards, Benoit -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Benoit, > On 08/08/2013 17:44, Suman Anna wrote: >> On 08/08/2013 09:34 AM, Kumar Gala wrote: >>> >>> On Aug 7, 2013, at 3:08 PM, Suman Anna wrote: >>> >>>> On 08/07/2013 12:41 PM, Kumar Gala wrote: >>>>> >>>>> On Aug 7, 2013, at 11:59 AM, Suman Anna wrote: >>>>> >>>>>> Kumar, >>>>>> >>>>>>>> Logic has been added to the OMAP2+ mailbox code to >>>>>>>> parse the mailbox dt nodes and construct the different >>>>>>>> mailboxes associated with the instance. The design is >>>>>>>> based on gathering the same information that was being >>>>>>>> passed previously through the platform data, except for >>>>>>>> the interrupt type configuration information. >>>>>>>> >>>>>>>> Signed-off-by: Suman Anna <s-anna@ti.com> >>>>>>>> --- >>>>>>>> .../devicetree/bindings/mailbox/omap-mailbox.txt | 43 +++++++ >>>>>>>> drivers/mailbox/mailbox-omap2.c | 130 >>>>>>>> ++++++++++++++++++--- >>>>>>>> 2 files changed, 158 insertions(+), 15 deletions(-) >>>>>>>> create mode 100644 >>>>>>>> Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>>>> >>>>>>>> diff --git >>>>>>>> a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>>>> b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>>>> new file mode 100644 >>>>>>>> index 0000000..8ffb08a >>>>>>>> --- /dev/null >>>>>>>> +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt >>>>>>>> @@ -0,0 +1,43 @@ >>>>>>>> +OMAP2+ Mailbox Driver >>>>>>>> + >>>>>>>> +Required properties: >>>>>>>> +- compatible: Should be one of the following, >>>>>>>> + "ti,omap2-mailbox" for >>>>>>>> + OMAP2420, OMAP2430, OMAP3430, OMAP3630 SoCs >>>>>>>> + "ti,omap4-mailbox" for >>>>>>>> + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs >>>>>>>> +- reg: Contains the mailbox register address range >>>>>>>> (base address >>>>>>>> + and length) >>>>>>>> +- interrupts: Contains the interrupt information for >>>>>>>> the mailbox >>>>>>>> + device. The format is dependent on which interrupt >>>>>>>> + controller the OMAP device uses >>>>>>>> +- ti,hwmods: Name of the hwmod associated with the mailbox >>>>>>>> +- ti,mbox-num-users: Number of targets (processor devices) >>>>>>>> that the mailbox device >>>>>>>> + can interrupt >>>>>>>> +- ti,mbox-num-fifos: Number of h/w fifos within the mailbox >>>>>>>> device >>>>>>> >>>>>>> Isn't "ti,mbox-num-users", "ti,mbox-num-fifos" this SoC specific, >>>>>>> why do we need to encode in the device tree. Can we not have a >>>>>>> more SoC specific compatiable and encode such info in the driver >>>>>>> as part of the .data field in of_device_id ? >>>>>> >>>>>> They are IP design parameters for the number of h/w fifos and >>>>>> interrupts >>>>>> coming out of the IP block, with the functionality identical. This >>>>>> information could not be read from any registers. Until OMAP5, we >>>>>> always >>>>>> had a single IP in the SoC and so these could been encoded in the >>>>>> driver. But in DRA7xx, a new SoC, we have 13 mailboxes which have >>>>>> differing number of these properties even though the functional IP >>>>>> block >>>>>> is same. >>>>> >>>>> Ah, I see. Since you've got examples of the same IP with different >>>>> design params in a given SoC than this makes sense. >>>>> >>>>> Is that true of ti,mbox-num-users? >>>> >>>> Yes, it is true of both "ti,mbox-num-users" and "ti,mbox-num-fifos". >>> >>> So I think it would be good to update the binding to convey that SoCs >>> might have multiple mbox units w/different design pararms (maybe a >>> short blurb as part of the intro). >> >> Sure will do. Will wait for Benoit also to come back on this series if I >> need to address any further review comments. > > I had the same concern than Kumar originally, so if nobody has anymore > complain with this binding, that fine to me. At least for the DTS part. > Thanks for the review. I will be re-spinning the series soon to address comments from Kevin on a different patch in this series, so planning to make some DT binding changes as well as part of that. regards Suman -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt new file mode 100644 index 0000000..8ffb08a --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt @@ -0,0 +1,43 @@ +OMAP2+ Mailbox Driver + +Required properties: +- compatible: Should be one of the following, + "ti,omap2-mailbox" for + OMAP2420, OMAP2430, OMAP3430, OMAP3630 SoCs + "ti,omap4-mailbox" for + OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs +- reg: Contains the mailbox register address range (base address + and length) +- interrupts: Contains the interrupt information for the mailbox + device. The format is dependent on which interrupt + controller the OMAP device uses +- ti,hwmods: Name of the hwmod associated with the mailbox +- ti,mbox-num-users: Number of targets (processor devices) that the mailbox device + can interrupt +- ti,mbox-num-fifos: Number of h/w fifos within the mailbox device +- ti,mbox-names: Array of the names of the mailboxes +- ti,mbox-data: Mailbox descriptor data private to each mailbox. The 4 + cells represent the following data, + Cell #1 (tx_id) - mailbox fifo id used for + transmitting messages + Cell #2 (rx_id) - mailbox fifo id on which messages + are received + Cell #3 (irq_id) - irq identifier index number to use + from the interrupts data + Cell #4 (usr_id) - mailbox user id for identifying the + interrupt into the MPU interrupt + controller. + +Example: + +/* OMAP4 */ +mailbox: mailbox@4a0f4000 { + compatible = "ti,omap4-mailbox"; + reg = <0x4a0f4000 0x200>; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mailbox"; + ti,mbox-num-users = <3>; + ti,mbox-num-fifos = <8>; + ti,mbox-names = "mbox-ipu", "mbox-dsp"; + ti,mbox-data = <0 1 0 0>, <3 2 0 0>; +}; diff --git a/drivers/mailbox/mailbox-omap2.c b/drivers/mailbox/mailbox-omap2.c index 6c0687c..759f72c 100644 --- a/drivers/mailbox/mailbox-omap2.c +++ b/drivers/mailbox/mailbox-omap2.c @@ -14,6 +14,7 @@ #include <linux/slab.h> #include <linux/clk.h> #include <linux/err.h> +#include <linux/of_device.h> #include <linux/platform_device.h> #include <linux/io.h> #include <linux/pm_runtime.h> @@ -222,6 +223,21 @@ static struct omap_mbox_ops omap2_mbox_ops = { .restore_ctx = omap2_mbox_restore_ctx, }; +static const struct of_device_id omap_mailbox_of_match[] = { + { + .compatible = "ti,omap2-mailbox", + .data = (void *) MBOX_INTR_CFG_TYPE1, + }, + { + .compatible = "ti,omap4-mailbox", + .data = (void *) MBOX_INTR_CFG_TYPE2, + }, + { + /* end */ + }, +}; +MODULE_DEVICE_TABLE(of, omap_mailbox_of_match); + static int omap2_mbox_probe(struct platform_device *pdev) { struct resource *mem; @@ -229,47 +245,127 @@ static int omap2_mbox_probe(struct platform_device *pdev) struct omap_mbox **list, *mbox, *mboxblk; struct omap_mbox2_priv *priv, *privblk; struct omap_mbox_pdata *pdata = pdev->dev.platform_data; - struct omap_mbox_dev_info *info; struct omap_mbox_device *mdev; - int i; - - if (!pdata || !pdata->info_cnt || !pdata->info) { + struct omap_mbox_dev_info *info, *of_info = NULL; + struct device_node *node = pdev->dev.of_node; + int i, j; + u32 info_count = 0, intr_type = 0; + u32 num_users = 0, num_fifos = 0; + u32 dlen, dsize = 4; + u32 *tmp; + const __be32 *mbox_data; + + if (!node && (!pdata || !pdata->info_cnt || !pdata->info)) { pr_err("%s: platform not supported\n", __func__); return -ENODEV; } + if (node) { + intr_type = (u32)of_match_device(omap_mailbox_of_match, + &pdev->dev)->data; + if (intr_type != 0 && intr_type != 1) { + dev_err(&pdev->dev, "invalid match data value\n"); + return -EINVAL; + } + + if (of_property_read_u32(node, "ti,mbox-num-users", + &num_users)) { + dev_err(&pdev->dev, + "no ti,mbox-num-users configuration found\n"); + return -ENODEV; + } + + if (of_property_read_u32(node, "ti,mbox-num-fifos", + &num_fifos)) { + dev_err(&pdev->dev, + "no ti,mbox-num-fifos configuration found\n"); + return -ENODEV; + } + + info_count = of_property_count_strings(node, "ti,mbox-names"); + if (!info_count) { + dev_err(&pdev->dev, "no mbox devices found\n"); + return -ENODEV; + } + + mbox_data = of_get_property(node, "ti,mbox-data", &dlen); + if (!mbox_data) { + dev_err(&pdev->dev, "no mbox device data found\n"); + return -ENODEV; + } + dlen /= sizeof(dsize); + if (dlen != dsize * info_count) { + dev_err(&pdev->dev, "mbox device data is truncated\n"); + return -ENODEV; + } + + of_info = kzalloc(info_count * sizeof(*of_info), GFP_KERNEL); + if (!of_info) + return -ENOMEM; + + i = 0; + while (i < info_count) { + info = of_info + i; + if (of_property_read_string_index(node, + "ti,mbox-names", i, &info->name)) { + dev_err(&pdev->dev, + "mbox_name [%d] read failed\n", i); + ret = -ENODEV; + goto free_of; + } + + tmp = &info->tx_id; + for (j = 0; j < dsize; j++) { + tmp[j] = of_read_number( + mbox_data + j + (i * dsize), 1); + } + i++; + } + } + + if (!node) { /* non-DT device creation */ + info_count = pdata->info_cnt; + info = pdata->info; + intr_type = pdata->intr_type; + num_users = pdata->num_users; + num_fifos = pdata->num_fifos; + } else { + info = of_info; + } + mdev = kzalloc(sizeof(*mdev), GFP_KERNEL); - if (!mdev) - return -ENOMEM; + if (!mdev) { + ret = -ENOMEM; + goto free_of; + } /* allocate one extra for marking end of list */ - list = kzalloc((pdata->info_cnt + 1) * sizeof(*list), GFP_KERNEL); + list = kzalloc((info_count + 1) * sizeof(*list), GFP_KERNEL); if (!list) { ret = -ENOMEM; goto free_mdev; } - mboxblk = mbox = kzalloc(pdata->info_cnt * sizeof(*mbox), GFP_KERNEL); + mboxblk = mbox = kzalloc(info_count * sizeof(*mbox), GFP_KERNEL); if (!mboxblk) { ret = -ENOMEM; goto free_list; } - privblk = priv = kzalloc(pdata->info_cnt * sizeof(*priv), GFP_KERNEL); + privblk = priv = kzalloc(info_count * sizeof(*priv), GFP_KERNEL); if (!privblk) { ret = -ENOMEM; goto free_mboxblk; } - info = pdata->info; - for (i = 0; i < pdata->info_cnt; i++, info++, priv++) { + for (i = 0; i < info_count; i++, info++, priv++) { priv->tx_fifo.msg = MAILBOX_MESSAGE(info->tx_id); priv->tx_fifo.fifo_stat = MAILBOX_FIFOSTATUS(info->tx_id); priv->rx_fifo.msg = MAILBOX_MESSAGE(info->rx_id); priv->rx_fifo.msg_stat = MAILBOX_MSGSTATUS(info->rx_id); priv->notfull_bit = MAILBOX_IRQ_NOTFULL(info->tx_id); priv->newmsg_bit = MAILBOX_IRQ_NEWMSG(info->rx_id); - if (pdata->intr_type) { + if (intr_type) { priv->irqenable = OMAP4_MAILBOX_IRQENABLE(info->usr_id); priv->irqstatus = OMAP4_MAILBOX_IRQSTATUS(info->usr_id); priv->irqdisable = @@ -279,7 +375,7 @@ static int omap2_mbox_probe(struct platform_device *pdev) priv->irqstatus = MAILBOX_IRQSTATUS(info->usr_id); priv->irqdisable = MAILBOX_IRQENABLE(info->usr_id); } - priv->intr_type = pdata->intr_type; + priv->intr_type = intr_type; mbox->priv = priv; mbox->parent = mdev; @@ -307,8 +403,8 @@ static int omap2_mbox_probe(struct platform_device *pdev) mutex_init(&mdev->cfg_lock); mdev->dev = &pdev->dev; - mdev->num_users = pdata->num_users; - mdev->num_fifos = pdata->num_fifos; + mdev->num_users = num_users; + mdev->num_fifos = num_fifos; mdev->mboxes = list; ret = omap_mbox_register(&pdev->dev, list); if (ret) @@ -317,6 +413,7 @@ static int omap2_mbox_probe(struct platform_device *pdev) pm_runtime_enable(mdev->dev); + kfree(of_info); return 0; unmap_mbox: @@ -329,6 +426,8 @@ free_list: kfree(list); free_mdev: kfree(mdev); +free_of: + kfree(of_info); return ret; } @@ -358,6 +457,7 @@ static struct platform_driver omap2_mbox_driver = { .remove = omap2_mbox_remove, .driver = { .name = "omap-mailbox", + .of_match_table = omap_mailbox_of_match, }, };
Logic has been added to the OMAP2+ mailbox code to parse the mailbox dt nodes and construct the different mailboxes associated with the instance. The design is based on gathering the same information that was being passed previously through the platform data, except for the interrupt type configuration information. Signed-off-by: Suman Anna <s-anna@ti.com> --- .../devicetree/bindings/mailbox/omap-mailbox.txt | 43 +++++++ drivers/mailbox/mailbox-omap2.c | 130 ++++++++++++++++++--- 2 files changed, 158 insertions(+), 15 deletions(-) create mode 100644 Documentation/devicetree/bindings/mailbox/omap-mailbox.txt