| Message ID | 20131001103305.813.70296.sendpatchset@w520 (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, Oct 01, 2013 at 07:33:05PM +0900, Magnus Damm wrote: > From: Magnus Damm <damm@opensource.se> > > Copy the device nodes from KZM9D reference into the KZM9D > device tree file. This will allow us to use a single DTS > file regarless of kernel configuration. In case of legacy > C board code the device nodes may or may not be used, but > in the multiplatform case all the DT device nodes are used. > > Signed-off-by: Magnus Damm <damm@opensource.se> > --- > > arch/arm/boot/dts/emev2-kzm9d.dts | 33 ++++++++++++++++++++++++++++++++- > 1 file changed, 32 insertions(+), 1 deletion(-) Thanks, I have queued this up in the dt3 branch. It should make it into v3.13 but if not I'll rename the branch dt after rebasing it on v3.13-rcX which will then be targeted at v3.14.
Hi Simon, On Thursday 03 October 2013 12:49:48 Simon Horman wrote: > On Tue, Oct 01, 2013 at 07:33:05PM +0900, Magnus Damm wrote: > > From: Magnus Damm <damm@opensource.se> > > > > Copy the device nodes from KZM9D reference into the KZM9D > > device tree file. This will allow us to use a single DTS > > file regarless of kernel configuration. In case of legacy > > C board code the device nodes may or may not be used, but > > in the multiplatform case all the DT device nodes are used. > > > > Signed-off-by: Magnus Damm <damm@opensource.se> > > --- > > > > arch/arm/boot/dts/emev2-kzm9d.dts | 33 +++++++++++++++++++++++++++++++- > > 1 file changed, 32 insertions(+), 1 deletion(-) > > Thanks, I have queued this up in the dt3 branch. Splitting the series across two branches would result in bisection breakages I'm afraid. Would it be an issue to queue all patches to a single branch ? > It should make it into v3.13 but if not I'll rename the branch > dt after rebasing it on v3.13-rcX which will then be targeted at v3.14.
On Thu, Oct 03, 2013 at 11:56:40AM +0200, Laurent Pinchart wrote: > Hi Simon, > > On Thursday 03 October 2013 12:49:48 Simon Horman wrote: > > On Tue, Oct 01, 2013 at 07:33:05PM +0900, Magnus Damm wrote: > > > From: Magnus Damm <damm@opensource.se> > > > > > > Copy the device nodes from KZM9D reference into the KZM9D > > > device tree file. This will allow us to use a single DTS > > > file regarless of kernel configuration. In case of legacy > > > C board code the device nodes may or may not be used, but > > > in the multiplatform case all the DT device nodes are used. > > > > > > Signed-off-by: Magnus Damm <damm@opensource.se> > > > --- > > > > > > arch/arm/boot/dts/emev2-kzm9d.dts | 33 +++++++++++++++++++++++++++++++- > > > 1 file changed, 32 insertions(+), 1 deletion(-) > > > > Thanks, I have queued this up in the dt3 branch. > > Splitting the series across two branches would result in bisection breakages > I'm afraid. Would it be an issue to queue all patches to a single branch ? Sure, I will re-arrange things accordingly.
--- 0001/arch/arm/boot/dts/emev2-kzm9d.dts +++ work/arch/arm/boot/dts/emev2-kzm9d.dts 2013-09-26 19:42:16.000000000 +0900 @@ -1,7 +1,7 @@ /* * Device Tree Source for the KZM9D board * - * Copyright (C) 2012 Renesas Solutions Corp. + * Copyright (C) 2013 Renesas Solutions Corp. * * This file is licensed under the terms of the GNU General Public License * version 2. This program is licensed "as is" without any warranty of any @@ -23,4 +23,35 @@ chosen { bootargs = "console=ttyS1,115200n81 ignore_loglevel root=/dev/nfs ip=dhcp"; }; + + reg_1p8v: regulator@0 { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_3p3v: regulator@1 { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + lan9220@20000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0x20000000 0x10000>; + phy-mode = "mii"; + interrupt-parent = <&gpio0>; + interrupts = <1 1>; /* active high */ + reg-io-width = <4>; + smsc,irq-active-high; + smsc,irq-push-pull; + vddvario-supply = <®_1p8v>; + vdd33a-supply = <®_3p3v>; + }; };