@@ -11,6 +11,10 @@ Required properties:
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
- dma
+- #iommu-cells : Must be <1>. This dictates the length of DMA specifiers in
+ client nodes' dmas properties. The specifier represents the DMA request
+ select value for the peripheral. For more details, consult the Tegra TRM's
+ documentation of the APB DMA channel control register REQ_SEL field.
Examples:
@@ -36,4 +40,5 @@ apbdma: dma@6000a000 {
clocks = <&tegra_car 34>;
resets = <&tegra_car 34>;
reset-names = "dma";
+ #iommu-cells = <1>;
};
@@ -51,6 +51,11 @@ Required properties:
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
- i2c
+- dmas : Must contain an entry for each entry in clock-names.
+ See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+ - rx
+ - tx
Example:
@@ -64,5 +69,7 @@ Example:
clock-names = "div-clk", "fast-clk";
resets = <&tegra_car 12>;
reset-names = "i2c";
+ dmas = <&apbdma 16>, <&apbdma 16>;
+ dma-names = "rx", "tx";
status = "disabled";
};
@@ -4,14 +4,17 @@ Required properties:
- compatible : should be "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart".
- reg: Should contain UART controller registers location and length.
- interrupts: Should contain UART controller interrupts.
-- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
- request selector for this UART controller.
- clocks : Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- resets : Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
- serial
+- dmas : Must contain an entry for each entry in clock-names.
+ See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+ - rx
+ - tx
Optional properties:
- nvidia,enable-modem-interrupt: Enable modem interrupts. Should be enable
@@ -24,10 +27,11 @@ serial@70006000 {
reg = <0x70006000 0x40>;
reg-shift = <2>;
interrupts = <0 36 0x04>;
- nvidia,dma-request-selector = <&apbdma 8>;
nvidia,enable-modem-interrupt;
clocks = <&tegra_car 6>;
resets = <&tegra_car 6>;
reset-names = "serial";
+ dmas = <&apbdma 8>, <&apbdma 8>;
+ dma-names = "rx", "tx";
status = "disabled";
};
@@ -4,14 +4,17 @@ Required properties:
- compatible : "nvidia,tegra20-ac97"
- reg : Should contain AC97 controller registers location and length
- interrupts : Should contain AC97 interrupt
-- clocks : Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- resets : Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
- ac97
-- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
- request selector for the AC97 controller
+- dmas : Must contain an entry for each entry in clock-names.
+ See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+ - rx
+ - tx
+- clocks : Must contain one entry, for the module clock.
+ See ../clocks/clock-bindings.txt for details.
- nvidia,codec-reset-gpio : The Tegra GPIO controller's phandle and the number
of the GPIO used to reset the external AC97 codec
- nvidia,codec-sync-gpio : The Tegra GPIO controller's phandle and the number
@@ -23,10 +26,11 @@ ac97@70002000 {
compatible = "nvidia,tegra20-ac97";
reg = <0x70002000 0x200>;
interrupts = <0 81 0x04>;
- nvidia,dma-request-selector = <&apbdma 12>;
nvidia,codec-reset-gpio = <&gpio 170 0>;
nvidia,codec-sync-gpio = <&gpio 120 0>;
clocks = <&tegra_car 3>;
resets = <&tegra_car 3>;
reset-names = "ac97";
+ dmas = <&apbdma 12>, <&apbdma 12>;
+ dma-names = "rx", "tx";
};
@@ -4,14 +4,17 @@ Required properties:
- compatible : "nvidia,tegra20-i2s"
- reg : Should contain I2S registers location and length
- interrupts : Should contain I2S interrupt
-- clocks : Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- resets : Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
- i2s
-- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
- request selector for this I2S controller
+- dmas : Must contain an entry for each entry in clock-names.
+ See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+ - rx
+ - tx
+- clocks : Must contain one entry, for the module clock.
+ See ../clocks/clock-bindings.txt for details.
Example:
@@ -19,8 +22,9 @@ i2s@70002800 {
compatible = "nvidia,tegra20-i2s";
reg = <0x70002800 0x200>;
interrupts = < 45 >;
- nvidia,dma-request-selector = < &apbdma 2 >;
clocks = <&tegra_car 11>;
resets = <&tegra_car 11>;
reset-names = "i2s";
+ dmas = <&apbdma 21>, <&apbdma 21>;
+ dma-names = "rx", "tx";
};
@@ -7,11 +7,6 @@ Required properties:
- Tegra30 requires 2 entries, for the APBIF and AHUB/AUDIO register blocks.
- Tegra114 requires an additional entry, for the APBIF2 register block.
- interrupts : Should contain AHUB interrupt
-- nvidia,dma-request-selector : A list of the DMA channel specifiers. Each
- entry contains the Tegra DMA controller's phandle and request selector.
- If a single entry is present, the request selectors for the channels are
- assumed to be contiguous, and increment from this value.
- If multiple values are given, one value must be given per channel.
- clocks : Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
- clock-names : Must include the following entries:
@@ -36,6 +31,14 @@ Required properties:
- amx
- adx
- ranges : The bus address mapping for the configlink register bus.
+- dmas : Must contain an entry for each entry in clock-names.
+ See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+ - rx0 .. rx<n>
+ - tx0 .. tx<n>
+ ... where n is:
+ Tegra30: 3
+ Tegra114, Tegra124: 9
Can be empty since the mapping is 1:1.
- #address-cells : For the configlink bus. Should be <1>;
- #size-cells : For the configlink bus. Should be <1>.
@@ -62,6 +65,11 @@ ahub@70080000 {
reset-names = "d_audio", "apbif", "i2s0", "i2s1", "i2s2",
"i2s3", "i2s4", "dam0", "dam1", "dam2",
"spdif";
+ dmas = <&apbdma 1>, <&apbdma 1>;
+ <&apbdma 2>, <&apbdma 2>;
+ <&apbdma 3>, <&apbdma 3>;
+ <&apbdma 4>, <&apbdma 4>;
+ dma-names = "rx0", "tx0", "rx1", "tx1", "rx2", "tx2", "rx3", "tx3";
ranges;
#address-cells = <1>;
#size-cells = <1>;
@@ -4,16 +4,19 @@ Required properties:
- compatible : should be "nvidia,tegra114-spi".
- reg: Should contain SPI registers location and length.
- interrupts: Should contain SPI interrupts.
-- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
- request selector for this SPI controller.
-- clocks : Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- clock-names : Must include the following entries:
- spi
- resets : Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
- spi
+- dmas : Must contain an entry for each entry in clock-names.
+ See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+ - rx
+ - tx
+- clocks : Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
Recommended properties:
- spi-max-frequency: Definition as per
@@ -24,7 +27,6 @@ spi@7000d600 {
compatible = "nvidia,tegra114-spi";
reg = <0x7000d600 0x200>;
interrupts = <0 82 0x04>;
- nvidia,dma-request-selector = <&apbdma 16>;
spi-max-frequency = <25000000>;
#address-cells = <1>;
#size-cells = <0>;
@@ -32,5 +34,7 @@ spi@7000d600 {
clock-names = "spi";
resets = <&tegra_car 44>;
reset-names = "spi";
+ dmas = <&apbdma 16>, <&apbdma 16>;
+ dma-names = "rx", "tx";
status = "disabled";
};
@@ -4,14 +4,17 @@ Required properties:
- compatible : should be "nvidia,tegra20-sflash".
- reg: Should contain SFLASH registers location and length.
- interrupts: Should contain SFLASH interrupts.
-- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
- request selector for this SFLASH controller.
- clocks : Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- resets : Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
- spi
+- dmas : Must contain an entry for each entry in clock-names.
+ See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+ - rx
+ - tx
Recommended properties:
- spi-max-frequency: Definition as per
@@ -23,12 +26,13 @@ spi@7000c380 {
compatible = "nvidia,tegra20-sflash";
reg = <0x7000c380 0x80>;
interrupts = <0 39 0x04>;
- nvidia,dma-request-selector = <&apbdma 16>;
spi-max-frequency = <25000000>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&tegra_car 43>;
resets = <&tegra_car 43>;
reset-names = "spi";
+ dmas = <&apbdma 11>, <&apbdma 11>;
+ dma-names = "rx", "tx";
status = "disabled";
};
@@ -4,14 +4,17 @@ Required properties:
- compatible : should be "nvidia,tegra20-slink", "nvidia,tegra30-slink".
- reg: Should contain SLINK registers location and length.
- interrupts: Should contain SLINK interrupts.
-- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
- request selector for this SLINK controller.
- clocks : Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- resets : Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
- spi
+- dmas : Must contain an entry for each entry in clock-names.
+ See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+ - rx
+ - tx
Recommended properties:
- spi-max-frequency: Definition as per
@@ -23,12 +26,13 @@ spi@7000d600 {
compatible = "nvidia,tegra20-slink";
reg = <0x7000d600 0x200>;
interrupts = <0 82 0x04>;
- nvidia,dma-request-selector = <&apbdma 16>;
spi-max-frequency = <25000000>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&tegra_car 44>;
resets = <&tegra_car 44>;
reset-names = "spi";
+ dmas = <&apbdma 16>, <&apbdma 16>;
+ dma-names = "rx", "tx";
status = "disabled";
};