| Message ID | 1387329451-17480-3-git-send-email-john.tobias.ph@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, Dec 17, 2013 at 05:17:30PM -0800, John Tobias wrote: > Since of_init_opp_table is in imx6q-cpufreq.c, the imx6q_opp_init is no longer needed anymore. > The only question right now is the imx6q_opp_check_1p2ghz function. > > Is the function below are acceptible under imx6q_init_late?. > > if (!cpu_dev) > imx6q_opp_check_1p2ghz(cpu_dev); > > If not, what is the better way to impelement because the said function is board specific?. > > Signed-off-by: John Tobias <john.tobias.ph@gmail.com> > --- > arch/arm/mach-imx/mach-imx6q.c | 30 ++++-------------------------- > 1 file changed, 4 insertions(+), 26 deletions(-) > > diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c > index d0cfb22..f5d9e04 100644 > --- a/arch/arm/mach-imx/mach-imx6q.c > +++ b/arch/arm/mach-imx/mach-imx6q.c > @@ -183,31 +183,6 @@ put_node: > of_node_put(np); > } > > -static void __init imx6q_opp_init(void) > -{ > - struct device_node *np; > - struct device *cpu_dev = get_cpu_device(0); > - > - if (!cpu_dev) { > - pr_warn("failed to get cpu0 device\n"); > - return; > - } > - np = of_node_get(cpu_dev->of_node); > - if (!np) { > - pr_warn("failed to find cpu0 node\n"); > - return; > - } > - > - if (of_init_opp_table(cpu_dev)) { > - pr_warn("failed to init OPP table\n"); > - goto put_node; > - } > - > - imx6q_opp_check_1p2ghz(cpu_dev); > - > -put_node: > - of_node_put(np); > -} > > static struct platform_device imx6q_cpufreq_pdev = { > .name = "imx6q-cpufreq", > @@ -215,6 +190,7 @@ static struct platform_device imx6q_cpufreq_pdev = { > > static void __init imx6q_init_late(void) > { > + struct device *cpu_dev = get_cpu_device(0); > /* > * WAIT mode is broken on TO 1.0 and 1.1, so there is no point > * to run cpuidle on them. > @@ -223,8 +199,10 @@ static void __init imx6q_init_late(void) > imx6q_cpuidle_init(); > > if (IS_ENABLED(CONFIG_ARM_IMX6Q_CPUFREQ)) { > - imx6q_opp_init(); > platform_device_register(&imx6q_cpufreq_pdev); > + > + if (!cpu_dev) > + imx6q_opp_check_1p2ghz(cpu_dev); imx6q_opp_check_1p2ghz() only works after of_init_opp_table() is called. So you shouldn't make these changes in mach-imx6q.c, but in cpufreq driver check if platform already supplies an opp table, and only calls of_init_opp_table() in driver in case that platform hasn't. Then, for imx6q case where opp table is supplied by platform, driver will skip of_init_opp_table() call, while for imx6sl case where platform does not handle opp table, driver will just call of_init_opp_table(). Shawn > } > } > > -- > 1.8.3.2 > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Got it. thanks john On Tue, Dec 17, 2013 at 11:49 PM, Shawn Guo <shawn.guo@linaro.org> wrote: > On Tue, Dec 17, 2013 at 05:17:30PM -0800, John Tobias wrote: >> Since of_init_opp_table is in imx6q-cpufreq.c, the imx6q_opp_init is no longer needed anymore. >> The only question right now is the imx6q_opp_check_1p2ghz function. >> >> Is the function below are acceptible under imx6q_init_late?. >> >> if (!cpu_dev) >> imx6q_opp_check_1p2ghz(cpu_dev); >> >> If not, what is the better way to impelement because the said function is board specific?. >> >> Signed-off-by: John Tobias <john.tobias.ph@gmail.com> >> --- >> arch/arm/mach-imx/mach-imx6q.c | 30 ++++-------------------------- >> 1 file changed, 4 insertions(+), 26 deletions(-) >> >> diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c >> index d0cfb22..f5d9e04 100644 >> --- a/arch/arm/mach-imx/mach-imx6q.c >> +++ b/arch/arm/mach-imx/mach-imx6q.c >> @@ -183,31 +183,6 @@ put_node: >> of_node_put(np); >> } >> >> -static void __init imx6q_opp_init(void) >> -{ >> - struct device_node *np; >> - struct device *cpu_dev = get_cpu_device(0); >> - >> - if (!cpu_dev) { >> - pr_warn("failed to get cpu0 device\n"); >> - return; >> - } >> - np = of_node_get(cpu_dev->of_node); >> - if (!np) { >> - pr_warn("failed to find cpu0 node\n"); >> - return; >> - } >> - >> - if (of_init_opp_table(cpu_dev)) { >> - pr_warn("failed to init OPP table\n"); >> - goto put_node; >> - } >> - >> - imx6q_opp_check_1p2ghz(cpu_dev); >> - >> -put_node: >> - of_node_put(np); >> -} >> >> static struct platform_device imx6q_cpufreq_pdev = { >> .name = "imx6q-cpufreq", >> @@ -215,6 +190,7 @@ static struct platform_device imx6q_cpufreq_pdev = { >> >> static void __init imx6q_init_late(void) >> { >> + struct device *cpu_dev = get_cpu_device(0); >> /* >> * WAIT mode is broken on TO 1.0 and 1.1, so there is no point >> * to run cpuidle on them. >> @@ -223,8 +199,10 @@ static void __init imx6q_init_late(void) >> imx6q_cpuidle_init(); >> >> if (IS_ENABLED(CONFIG_ARM_IMX6Q_CPUFREQ)) { >> - imx6q_opp_init(); >> platform_device_register(&imx6q_cpufreq_pdev); >> + >> + if (!cpu_dev) >> + imx6q_opp_check_1p2ghz(cpu_dev); > > imx6q_opp_check_1p2ghz() only works after of_init_opp_table() is called. > So you shouldn't make these changes in mach-imx6q.c, but in cpufreq > driver check if platform already supplies an opp table, and only calls > of_init_opp_table() in driver in case that platform hasn't. Then, for > imx6q case where opp table is supplied by platform, driver will skip > of_init_opp_table() call, while for imx6sl case where platform does not > handle opp table, driver will just call of_init_opp_table(). > > Shawn > >> } >> } >> >> -- >> 1.8.3.2 >> > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c index d0cfb22..f5d9e04 100644 --- a/arch/arm/mach-imx/mach-imx6q.c +++ b/arch/arm/mach-imx/mach-imx6q.c @@ -183,31 +183,6 @@ put_node: of_node_put(np); } -static void __init imx6q_opp_init(void) -{ - struct device_node *np; - struct device *cpu_dev = get_cpu_device(0); - - if (!cpu_dev) { - pr_warn("failed to get cpu0 device\n"); - return; - } - np = of_node_get(cpu_dev->of_node); - if (!np) { - pr_warn("failed to find cpu0 node\n"); - return; - } - - if (of_init_opp_table(cpu_dev)) { - pr_warn("failed to init OPP table\n"); - goto put_node; - } - - imx6q_opp_check_1p2ghz(cpu_dev); - -put_node: - of_node_put(np); -} static struct platform_device imx6q_cpufreq_pdev = { .name = "imx6q-cpufreq", @@ -215,6 +190,7 @@ static struct platform_device imx6q_cpufreq_pdev = { static void __init imx6q_init_late(void) { + struct device *cpu_dev = get_cpu_device(0); /* * WAIT mode is broken on TO 1.0 and 1.1, so there is no point * to run cpuidle on them. @@ -223,8 +199,10 @@ static void __init imx6q_init_late(void) imx6q_cpuidle_init(); if (IS_ENABLED(CONFIG_ARM_IMX6Q_CPUFREQ)) { - imx6q_opp_init(); platform_device_register(&imx6q_cpufreq_pdev); + + if (!cpu_dev) + imx6q_opp_check_1p2ghz(cpu_dev); } }
Since of_init_opp_table is in imx6q-cpufreq.c, the imx6q_opp_init is no longer needed anymore. The only question right now is the imx6q_opp_check_1p2ghz function. Is the function below are acceptible under imx6q_init_late?. if (!cpu_dev) imx6q_opp_check_1p2ghz(cpu_dev); If not, what is the better way to impelement because the said function is board specific?. Signed-off-by: John Tobias <john.tobias.ph@gmail.com> --- arch/arm/mach-imx/mach-imx6q.c | 30 ++++-------------------------- 1 file changed, 4 insertions(+), 26 deletions(-)