@@ -599,14 +599,14 @@ parse_mipi(struct drm_i915_private *dev_priv, struct bdb_header *bdb)
{
struct bdb_mipi *mipi;
- mipi = find_section(bdb, BDB_MIPI);
+ mipi = find_section(bdb, BDB_MIPI_CONFIG);
if (!mipi) {
DRM_DEBUG_KMS("No MIPI BDB found");
return;
}
/* XXX: add more info */
- dev_priv->vbt.dsi.panel_id = mipi->panel_id;
+ dev_priv->vbt.dsi.panel_id = MIPI_DSI_GENERIC_PANEL_ID;
}
static void parse_ddi_port(struct drm_i915_private *dev_priv, enum port port,
@@ -104,7 +104,8 @@ struct vbios_data {
#define BDB_LVDS_LFP_DATA 42
#define BDB_LVDS_BACKLIGHT 43
#define BDB_LVDS_POWER 44
-#define BDB_MIPI 50
+#define BDB_MIPI_CONFIG 52
+#define BDB_MIPI_SEQUENCE 53
#define BDB_SKIP 254 /* VBIOS private block, ignore */
struct bdb_general_features {
@@ -711,44 +712,159 @@ int intel_parse_bios(struct drm_device *dev);
#define DVO_PORT_DPD 9
#define DVO_PORT_DPA 10
-/* MIPI DSI panel info */
-struct bdb_mipi {
- u16 panel_id;
- u16 bridge_revision;
-
- /* General params */
- u32 dithering:1;
- u32 bpp_pixel_format:1;
- u32 rsvd1:1;
- u32 dphy_valid:1;
- u32 resvd2:28;
+/* Block 52 contains MIPI Panel info
+ * 6 such enteries will there. Index into correct
+ * entery is based on the panel_index in #40 LFP
+ */
+#define MAX_MIPI_CONFIGURATIONS 6
- u16 port_info;
- u16 rsvd3:2;
- u16 num_lanes:2;
- u16 rsvd4:12;
+#define MIPI_DSI_UNDEFINED_PANEL_ID 0
+#define MIPI_DSI_GENERIC_PANEL_ID 1
- /* DSI config */
- u16 virt_ch_num:2;
- u16 vtm:2;
- u16 rsvd5:12;
+struct mipi_config {
+ u16 panel_id;
- u32 dsi_clock;
+ /* General Params */
+ u32 enable_dithering:1;
+ u32 rsvd1:1;
+ u32 is_bridge:1;
+
+ u32 panel_arch_type:2;
+ u32 is_cmd_mode:1;
+
+#define NON_BURST_SYNC_PULSE 0x1
+#define NON_BURST_SYNC_EVENTS 0x2
+#define BURST_MODE 0x3
+ u32 video_transfer_mode:2;
+
+ u32 cabc_supported:1;
+ u32 pwm_blc:1;
+
+ /* Bit 13:10 */
+#define PIXEL_FORMAT_RGB565 0x1
+#define PIXEL_FORMAT_RGB666 0x2
+#define PIXEL_FORMAT_RGB666_LOOSELY_PACKED 0x3
+#define PIXEL_FORMAT_RGB888 0x4
+ u32 videomode_color_format:4;
+
+ /* Bit 15:14 */
+#define ENABLE_ROTATION_0 0x0
+#define ENABLE_ROTATION_90 0x1
+#define ENABLE_ROTATION_180 0x2
+#define ENABLE_ROTATION_270 0x3
+ u32 rotation:2;
+ u32 bta_enabled:1;
+ u32 rsvd2:15;
+
+ /* 2 byte Port Description */
+#define DUAL_LINK_NOT_SUPPORTED 0
+#define DUAL_LINK_FRONT_BACK 1
+#define DUAL_LINK_PIXEL_ALT 2
+ u16 dual_link:2;
+ u16 lane_cnt:2;
+ u16 rsvd3:12;
+
+ u16 rsvd4;
+
+ u8 rsvd5[5];
+ u32 dsi_ddr_clk;
u32 bridge_ref_clk;
- u16 rsvd_pwr;
- /* Dphy Params */
- u32 prepare_cnt:5;
- u32 rsvd6:3;
+#define BYTE_CLK_SEL_20MHZ 0
+#define BYTE_CLK_SEL_10MHZ 1
+#define BYTE_CLK_SEL_5MHZ 2
+ u8 byte_clk_sel:2;
+
+ u8 rsvd6:6;
+
+ /* DPHY Flags */
+ u16 dphy_param_valid:1;
+ u16 eot_pkt_disabled:1;
+ u16 enable_clk_stop:1;
+ u16 rsvd7:13;
+
+ u32 hs_tx_timeout;
+ u32 lp_rx_timeout;
+ u32 turn_around_timeout;
+ u32 device_reset_timer;
+ u32 master_init_timer;
+ u32 dbi_bw_timer;
+ u32 lp_byte_clk_val;
+
+ /* 4 byte Dphy Params */
+ u32 prepare_cnt:6;
+ u32 rsvd8:2;
u32 clk_zero_cnt:8;
u32 trail_cnt:5;
- u32 rsvd7:3;
+ u32 rsvd9:3;
u32 exit_zero_cnt:6;
- u32 rsvd8:2;
+ u32 rsvd10:2;
- u32 hl_switch_cnt;
- u32 lp_byte_clk;
u32 clk_lane_switch_cnt;
+ u32 hl_switch_cnt;
+
+ u32 rsvd11[6];
+
+ /* timings based on dphy spec */
+ u8 tclk_miss;
+ u8 tclk_post;
+ u8 rsvd12;
+ u8 tclk_pre;
+ u8 tclk_prepare;
+ u8 tclk_settle;
+ u8 tclk_term_enable;
+ u8 tclk_trail;
+ u16 tclk_prepare_clkzero;
+ u8 rsvd13;
+ u8 td_term_enable;
+ u8 teot;
+ u8 ths_exit;
+ u8 ths_prepare;
+ u16 ths_prepare_hszero;
+ u8 rsvd14;
+ u8 ths_settle;
+ u8 ths_skip;
+ u8 ths_trail;
+ u8 tinit;
+ u8 tlpx;
+ u8 rsvd15[3];
+
+ /* GPIOs */
+ u8 panel_enable;
+ u8 bl_enable;
+ u8 pwm_enable;
+ u8 reset_r_n;
+ u8 pwr_down_r;
+ u8 stdby_r_n;
+
} __packed;
+/* Block 52 contains MIPI configuration block
+ * 6 * bdb_mipi_config, followed by 6 pps data
+ * block below
+ *
+ * all delays in ms
+ */
+struct mipi_pps_data {
+ u16 panel_on_delay;
+ u16 bl_enable_delay;
+ u16 bl_disable_delay;
+ u16 panel_off_delay;
+ u16 panel_power_cycle_delay;
+};
+
+struct bdb_mipi_config {
+ struct mipi_config config[MAX_MIPI_CONFIGURATIONS];
+ struct mipi_pps_data pps[MAX_MIPI_CONFIGURATIONS];
+};
+
+/* Block 53 contains MIPI sequences as needed by the panel
+ * for enabling it. This block can be variable in size and
+ * can be maximum of 6 blocks
+ */
+struct bdb_mipi_sequence {
+ u8 version;
+ u8 data[0];
+};
+
#endif /* _I830_BIOS_H_ */
MIPI Block #52 which provides configuration details for the MIPI panel including dphy settings as per panel and tcon specs Block #53 gives information on panel enable sequences v2: Address review comemnts from Jani - Move panel ids from intel_dsi.h to intel_bios.h - bdb_mipi_config structure improvements for cleaner code - Adding units for the pps delays, all in ms - change data structure to be more cleaner and simple Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> --- drivers/gpu/drm/i915/intel_bios.c | 4 +- drivers/gpu/drm/i915/intel_bios.h | 174 +++++++++++++++++++++++++++++++------- 2 files changed, 147 insertions(+), 31 deletions(-)