new file mode 100644
@@ -0,0 +1,82 @@
+/*
+ * Common file for omap dpi panels with QVGA and reset pins
+ *
+ * Note that the board specifc DTS file needs to specify
+ * at minimum the GPIO enable-gpios for display, and
+ * gpios for gpio-backlight.
+ */
+
+/ {
+ aliases {
+ display0 = &lcd0;
+ };
+
+ backlight0: backlight {
+ compatible = "gpio-backlight";
+ };
+
+ /* 3.3V GPIO controlled regulator for LCD_ENVDD */
+ lcd_3v3: regulator-lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <70000>;
+ regulator-always-on;
+ };
+
+ lcd0: display {
+ compatible = "sharp,ls037v7dw01";
+ label = "lcd";
+ power-supply = <&lcd_3v3>;
+ panel-timing {
+ clock-frequency = <5400000>;
+ hback-porch = <39>;
+ hactive = <240>;
+ hfront-porch = <3>;
+ hsync-len = <3>;
+ vback-porch = <7>;
+ vactive = <320>;
+ vfront-porch = <2>;
+ vsync-len = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+ };
+};
+
+&dss {
+ status = "ok";
+ vdds_dsi-supply = <&vpll2>;
+ port {
+ dpi_out: endpoint {
+ remote-endpoint = <&lcd_in>;
+ data-lines = <18>;
+ };
+ };
+};
+
+&mcspi1 {
+ tsc2046@0 {
+ reg = <0>; /* CS0 */
+ compatible = "ti,tsc2046";
+ spi-max-frequency = <1000000>;
+ vcc-supply = <&lcd_3v3>;
+ ti,x-min = /bits/ 16 <0>;
+ ti,x-max = /bits/ 16 <8000>;
+ ti,y-min = /bits/ 16 <0>;
+ ti,y-max = /bits/ 16 <4800>;
+ ti,x-plate-ohms = /bits/ 16 <40>;
+ ti,pressure-max = /bits/ 16 <255>;
+ ti,swap-xy;
+ linux,wakeup;
+ };
+};
@@ -26,7 +26,44 @@
};
};
+&dss {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &dss_dpi_pins1
+ &dss_dpi_pins2
+ >;
+};
+
&omap3_pmx_core {
+ dss_dpi_pins1: pinmux_dss_dpi_pins2 {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+
+ OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+
+ OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
+ OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
+ OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
+ OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
+ OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
+ OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
+ >;
+ };
+
mmc1_pins: pinmux_mmc1_pins {
pinctrl-single,pins = <
0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
@@ -75,6 +112,19 @@
};
};
+&omap3_pmx_wkup {
+ dss_dpi_pins2: pinmux_dss_dpi_pins1 {
+ pinctrl-single,pins = <
+ 0x0a (PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
+ 0x0c (PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
+ 0x10 (PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
+ 0x12 (PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
+ 0x14 (PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
+ 0x16 (PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
+ >;
+ };
+};
+
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
@@ -44,6 +44,11 @@
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
+#include "omap-panel-sharp-ls037v7dw01.dtsi"
+
+&backlight0 {
+ gpios = <&twl_gpio 18 GPIO_ACTIVE_HIGH>;
+};
&i2c2 {
clock-frequency = <400000>;
@@ -61,6 +66,48 @@
};
};
+&lcd_3v3 {
+ gpio = <&gpio5 25 GPIO_ACTIVE_LOW>; /* gpio153 */
+ enable-active-low;
+};
+
+&lcd0 {
+ reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */
+ /*
+ * The LCD is sideways, so we want the VGA mode instead of
+ * QVGA mode. Probably also want to have omapfb.rotate=3
+ * in the kernel cmdline until there's a binding for that.
+ */
+ enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */
+ &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */
+ &gpio1 3 GPIO_ACTIVE_HIGH /* gpio3, lcd UD */
+ &gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */
+
+ panel-timing {
+ clock-frequency = <19200000>;
+ hback-porch = <28>;
+ hactive = <480>;
+ hfront-porch = <1>;
+ hsync-len = <2>;
+ vback-porch = <1>;
+ vactive = <640>;
+ vfront-porch = <1>;
+ vsync-len = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+};
+
+&mcspi1 {
+ tsc2046@0 {
+ interrupt-parent = <&gpio6>;
+ interrupts = <15 0>; /* gpio175 */
+ pendown-gpio = <&gpio6 15 0>;
+ };
+};
+
&mmc1 {
vmmc-supply = <&vmmc1>;
vmmc_aux-supply = <&vsim>;
@@ -164,6 +164,7 @@
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
+#include "omap-panel-sharp-ls037v7dw01.dtsi"
&i2c2 {
clock-frequency = <400000>;
@@ -173,6 +174,31 @@
clock-frequency = <400000>;
};
+&lcd_3v3 {
+ gpio = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+};
+
+&lcd0 {
+ reset-gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>; /* gpio55, lcd RESB */
+ gpios = <&gpio2 24 GPIO_ACTIVE_LOW /* gpio56, lcd MO */
+ 0 /* lcd LR */
+ 0 /* lcd UD */
+ 0>; /* lcd INI */
+};
+
+&backlight0 {
+ gpios = <&twl_gpio 15 GPIO_ACTIVE_LOW>;
+};
+
+&mcspi1 {
+ tsc2046@0 {
+ interrupt-parent = <&gpio2>;
+ interrupts = <22 0>; /* gpio54 */
+ pendown-gpio = <&gpio2 22 0>;
+ };
+};
+
&mmc1 {
/* See 35xx errata 2.1.1.128 in SPRZ278F */
compatible = "ti,omap3-pre-es3-hsmmc";
@@ -247,8 +273,3 @@
/* Needed for ads7846 */
regulator-name = "vcc";
};
-
-&vpll2 {
- /* Needed for DSS */
- regulator-name = "vdds_dsi";
-};
Looks like quite a few omaps have sharp ls037v7dw01 that's configured as various panel dpi entries for whatever legacy reasons. For device tree based support, let's just configure these properly for panel ls037v7dw01 instead of panel dpi. This patch creates a common file for panel ls037v7dw01, and makes boards ldp and omap3-evm to use it. The panel for ldp is configured in the qvga mode and omap3-evm panel in vga mode. The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen controller for the omaps, so let's add a basic configuration for the touchscreen also using the default values. Note that we can now remove the regulator-name = "vdds_dsi" entry for ldp, that's no longer needed as we have the entry for vdds_dsi-supply = <&vpll2>. Signed-off-by: Tony Lindgren <tony@atomide.com> --- .../arm/boot/dts/omap-panel-sharp-ls037v7dw01.dtsi | 82 ++++++++++++++++++++++ arch/arm/boot/dts/omap3-evm-37xx.dts | 50 +++++++++++++ arch/arm/boot/dts/omap3-evm-common.dtsi | 47 +++++++++++++ arch/arm/boot/dts/omap3-ldp.dts | 31 ++++++-- 4 files changed, 205 insertions(+), 5 deletions(-) create mode 100644 arch/arm/boot/dts/omap-panel-sharp-ls037v7dw01.dtsi