Message ID | 1398759638-13299-1-git-send-email-srinivas.kandagatla@linaro.org (mailing list archive) |
---|---|
State | Superseded, archived |
Headers | show |
On Tue, Apr 29, 2014 at 10:20 AM, <srinivas.kandagatla@linaro.org> wrote: > From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > MCICLK register layout is bit different to the standard pl180 register layout. > Qcom SDCC controller some setup in MCICLK register to get it going. So this > patch adds new setup and makes it specific to Qcom hw designer. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (...) > - if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) > - clk |= MCI_4BIT_BUS; > - if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) > - clk |= MCI_ST_8BIT_BUS; > + if (host->hw_designer == AMBA_VENDOR_QCOM) { > + clk |= MCI_CLK_QCOM_FLOWENA; > + clk |= (MCI_CLK_QCOM_SEL_FEEDBACK_CLK << > + MCI_CLK_QCOM_SEL_IN_SHIFT); /* feedback clk */ > + if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) > + clk |= MCI_CLK_QCOM_WIDEBUS_8; > + else if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) > + clk |= MCI_CLK_QCOM_WIDEBUS_4; > + else > + clk |= MCI_CLK_QCOM_WIDEBUS_1; > + > + if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50) { > + /* clear SELECT_IN field */ > + clk &= ~(MCI_CLK_QCOM_SEL_MASK << > + MCI_CLK_QCOM_SEL_IN_SHIFT); > + /* set DDR timing mode */ > + clk |= (MCI_CLK_QCOM_SEL_DDR_MODE << > + MCI_CLK_QCOM_SEL_IN_SHIFT); > + } > + clk |= (MCI_CLK_SDC4_MCLK_SEL_MCLK << > + MCI_CLK_SDC4_MCLK_SEL_SHIFT); > > - if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50) > - clk |= MCI_ST_UX500_NEG_EDGE; > + } else { > + if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) > + clk |= MCI_4BIT_BUS; > + if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) > + clk |= MCI_ST_8BIT_BUS; > + > + if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50) > + clk |= MCI_ST_UX500_NEG_EDGE; > + } Again follow the pattern of storing register templates in the vendor_data struct. I think you will quickly realize how this can be cut down with new fields like .clk_4bitmode etc. > /* Modified PL180 on Versatile Express platform */ > #define MCI_ARM_HWFCEN (1 << 12) > > +/* Modified on Qualcomm Integrations */ First: follow the convention set for the ST-specific registers that look e.g. like this: MCI_ST_8BIT_BUS i.e. MCI_<vendor>_SPECIFIER So the below becomes MCI_QCOM_CLK_WIDEBUS... etc. > +#define MCI_CLK_QCOM_WIDEBUS_1 (0 << 10) > +#define MCI_CLK_QCOM_WIDEBUS_4 (2 << 10) > +#define MCI_CLK_QCOM_WIDEBUS_8 (3 << 10) Compare to what we have: #define MMCICLOCK 0x004 #define MCI_CLK_ENABLE (1 << 8) #define MCI_CLK_PWRSAVE (1 << 9) #define MCI_CLK_BYPASS (1 << 10) #define MCI_4BIT_BUS (1 << 11) MCI_CLK_QCOM_WIDEBUS_1 is clearly surplus since it is not setting any bit. MCI_CLK_QCOM_WIDEBUS_4 (2 << 10) == MCI_4BIT_BUS (1 <<11), this is the same thing just expressed in two ways! No need to have some surplus definition adding to the confusion. Just use MCI_4BIT_BUS The only thing that is really different is MCI_CLK_QCOM_WIDEBUS_8 which whould have the name (following the sibling definitions for the ST block): #define MCI_QCOM_8BIT_BUS (3 << 10) > +#define MCI_CLK_QCOM_FLOWENA (1 << 12) Rename: MCI_QCOM_CLK_HWFCEN (1<<13) to match sibling definitions. It's clear that this enabled hardware flow control and that name is more helpful to understand what is going on. > +#define MCI_CLK_QCOM_INVERTOUT (1 << 13) Rename: MCI_QCOM_CLK_INV To match siblings. > +/* select in latch data and command */ > +#define MCI_CLK_QCOM_SEL_IN_SHIFT (14) > +#define MCI_CLK_QCOM_SEL_MASK (0x3) > +#define MCI_CLK_QCOM_SEL_RISING_EDGE (1) > +#define MCI_CLK_QCOM_SEL_FEEDBACK_CLK (2) > +#define MCI_CLK_QCOM_SEL_DDR_MODE (3) > + > +/* mclk selection */ > +#define MCI_CLK_SDC4_MCLK_SEL_SHIFT (23) > +#define MCI_CLK_SDC4_MCLK_SEL_MASK (0x3) > +#define MCI_CLK_SDC4_MCLK_SEL_FB_CLK (1) > +#define MCI_CLK_SDC4_MCLK_SEL_MCLK (2) These seem to have no related siblings but should still be renamed MCL_QCOM_* Yours, Linus Walleij -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Thanks Linus W. On 13/05/14 09:19, Linus Walleij wrote: > Again follow the pattern of storing register templates in the vendor_data > struct. I think you will quickly realize how this can be cut down with > new fields like .clk_4bitmode etc. > >> > /* Modified PL180 on Versatile Express platform */ >> > #define MCI_ARM_HWFCEN (1 << 12) >> > >> >+/* Modified on Qualcomm Integrations */ > First: follow the convention set for the ST-specific registers that > look e.g. like this: I agree, Will fix these in next version. > > MCI_ST_8BIT_BUS i.e. MCI_<vendor>_SPECIFIER > So the below becomes MCI_QCOM_CLK_WIDEBUS... etc. > -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index 306e0c8..35aed38 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -326,13 +326,37 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired) /* Set actual clock for debug */ host->mmc->actual_clock = host->cclk; - if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) - clk |= MCI_4BIT_BUS; - if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) - clk |= MCI_ST_8BIT_BUS; + if (host->hw_designer == AMBA_VENDOR_QCOM) { + clk |= MCI_CLK_QCOM_FLOWENA; + clk |= (MCI_CLK_QCOM_SEL_FEEDBACK_CLK << + MCI_CLK_QCOM_SEL_IN_SHIFT); /* feedback clk */ + if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) + clk |= MCI_CLK_QCOM_WIDEBUS_8; + else if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) + clk |= MCI_CLK_QCOM_WIDEBUS_4; + else + clk |= MCI_CLK_QCOM_WIDEBUS_1; + + if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50) { + /* clear SELECT_IN field */ + clk &= ~(MCI_CLK_QCOM_SEL_MASK << + MCI_CLK_QCOM_SEL_IN_SHIFT); + /* set DDR timing mode */ + clk |= (MCI_CLK_QCOM_SEL_DDR_MODE << + MCI_CLK_QCOM_SEL_IN_SHIFT); + } + clk |= (MCI_CLK_SDC4_MCLK_SEL_MCLK << + MCI_CLK_SDC4_MCLK_SEL_SHIFT); - if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50) - clk |= MCI_ST_UX500_NEG_EDGE; + } else { + if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) + clk |= MCI_4BIT_BUS; + if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) + clk |= MCI_ST_8BIT_BUS; + + if (host->mmc->ios.timing == MMC_TIMING_UHS_DDR50) + clk |= MCI_ST_UX500_NEG_EDGE; + } mmci_write_clkreg(host, clk); } diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h index 58b1b88..0a6de1c 100644 --- a/drivers/mmc/host/mmci.h +++ b/drivers/mmc/host/mmci.h @@ -31,6 +31,27 @@ /* Modified PL180 on Versatile Express platform */ #define MCI_ARM_HWFCEN (1 << 12) +/* Modified on Qualcomm Integrations */ +#define MCI_CLK_QCOM_WIDEBUS_1 (0 << 10) +#define MCI_CLK_QCOM_WIDEBUS_4 (2 << 10) +#define MCI_CLK_QCOM_WIDEBUS_8 (3 << 10) +#define MCI_CLK_QCOM_FLOWENA (1 << 12) +#define MCI_CLK_QCOM_INVERTOUT (1 << 13) + +/* select in latch data and command */ +#define MCI_CLK_QCOM_SEL_IN_SHIFT (14) +#define MCI_CLK_QCOM_SEL_MASK (0x3) +#define MCI_CLK_QCOM_SEL_RISING_EDGE (1) +#define MCI_CLK_QCOM_SEL_FEEDBACK_CLK (2) +#define MCI_CLK_QCOM_SEL_DDR_MODE (3) + +/* mclk selection */ +#define MCI_CLK_SDC4_MCLK_SEL_SHIFT (23) +#define MCI_CLK_SDC4_MCLK_SEL_MASK (0x3) +#define MCI_CLK_SDC4_MCLK_SEL_FB_CLK (1) +#define MCI_CLK_SDC4_MCLK_SEL_MCLK (2) + + #define MMCIARGUMENT 0x008 #define MMCICOMMAND 0x00c #define MCI_CPSM_RESPONSE (1 << 6)