Message ID | CAN8cciaAazGX4HZet+UgbWGN4iOk9hknCjYTtdwD+k+ptqakOw@mail.gmail.com (mailing list archive) |
---|---|
State | Changes Requested |
Delegated to: | Takashi Iwai |
Headers | show |
24.05.2014 11:10, Raymond Yau wrote: > > > >> > >> The appl_ptr can be placed in any position in the ring buffer for the > >> application to write data but the sound card fetch data from this ring > >> buffer sequentially, however snd_pcm_write() assume the maximum distance > >> between appl_ptr and hwptr is only one buffer > >> > >> > https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda/hda_intel.c?id=2ae66c26550cd94b0e2606a9275eb0ab7070ad0e > >> > >> Do you mean hwptr does not decrease by one period when you use arbitrary > >> period sizes for hda-Intel ? > > > > > > I cannot comment on this commit. But > "snd_hda_intel.align_buffer_size=1" indeed existed on my kernel command > line (for no good reason now - so removed), and I don't use a strange > period size. > > 3.6.2 Buffer Descriptor List > > There must be at least two entries in the list, with a maximum of 256 > entries. > > 3.6.3 Buffer Descriptor List Entry > > the buffers described by BDLE must start on 128 bytes boundary > > refer to azx_setup_periods, if one period represent one BDLE , the > buffers described by two periods must start on 128 bytes boundary > > with default prealloc_max = 64, pulseaudio are forced to use maximum > buffer size / period size which are also 128 bytes aligned > > when you specifiy prealloc_max = 4096, one second 48000Hz is also > aligned to 128 bytes boundary but one second 44100 Hz is not I am not sure I can continue this line of discussion usefully, because I don't understand the purpose. If this is an attempt to understand the granularity of hw_ptr (which would indeed be useful), then I cannot help. If this is a report of a possible non-rewind-related bug in PulseAudio, please start a new thread. > > > > > > > Still, the bug (negative reported rewindable amount) also exists > without align_buffer_size=1. > > > > > >> > >> e.g. 48 samples (192 bytes) when using 1ms period time and stereo > >> instead of 4 channels > > > > > > Not tested. > > The implementation dependent FIFO Size affect the number of the bytes > that could be fetched by the controller at one time. > > 3.3.40 Offset 90: {IOB}SDnFIFOS – Input/Output/Bidirectional Stream > Descriptor n FIFO Size > > FIFO Size (FIFOS): Indicates the maximum number of bytes that could be > fetched by the controller at one time. This is the maximum number of > bytes that may have been DMA?d into memory but not yet transmitted on > the link, and is also the maximum possible value that the LPIB count > will increase by at one time. OK, this looks very relevant. Is this the same value as would be returned by snd_pcm_hw_params_get_fifo_size()? If not, why, and how do I view this value? > > > > > > > > >> > >> you program seen hang when using pulse plugin > > > > > > I am not interested in any more rewind-related bug reports for the > pulse plugin. This particular bug will be fixed, together with many > others, by always returning 0 from the .rewindable callback for ioplug > if mmap_rw is false. > > why do you assume rewind is supported if mmap_rw is true ? any example The example is jack plugin (in fact, the only plugin known to me that sets mmap_rw to true). It does support rewinds, as I have already explained and tested. It works because the periodic transfer of samples to JACK is done in a separate realtime thread. Application writes samples into a circular mmap-style buffer, ioplug uses the generic mmap-style functions for rewinding that buffer, and the thread reads from it, just as a real sound card would do. So an application can safely rewind any samples that it has written to that buffer but that the thread hasn't yet copied to JACK. Of course it is possible to write a buggy ioplug-based plugin that doesn't really support rewinds even though it sets mmap_rw to true (e.g. by implementing the transfer callback - the real problem here, if my understanding is correct, is that it has no access to the application pointer). But in reality I don't know any such plugin. Still, you are right, and a better idea would be to say: an ioplug-based plugin can be assumed to support rewinds if and only if it sets mmap_rw to true and does not provide a transfer callback. I say so because such architecture forces the plugin to use a low-latency thread to do the actual transfers and also avoids the need to care about the application pointer altogether. In other words, such plugin implements an architecture similar to one of a real DMA-based sound card. > > > > > > >> > >> > > >> > > >> > How do I test this? Could you please post some userspace test code or > >> a kernel patch, together with the instructions? > >> > > >> > >> Attach the patch to dump the values of the audio function group > capability > > > > > > There was no attachment. > > > > > >> There are three cases > >> > >> 1) delay in analog output > delay in digital output e.g, idt codecs > >> 2) delay in analog output < delay in digital output e.g. adi codecs > >> 3) no delay in audio widgets , digital output and analog output have no > >> delay difference when output delay in audio function group is non > zero ? > > > > > > Yes, that's logical. > > > > > >> > >> It is unlikely for ordinary user to measure the delay without using > >> oscilloscope since the Analog speaker and digital receiver also have > delay > > > > > > Correct. Also, while delay in analog speakers can be often rightfully > assumed to be 0 samples, this is not the case for digital receivers. In > other words, the delay on the digital path is in fact unknown. > > If 13 samples delay in analog output is due to the five bands equalizer > in IDT codecs, the headphone should not has same delay since equalizer > in not present in the headphone path, may need to implement > multi-channel capture to find out any delay between headphone and line out > For me an easier way would be to go to the nearest electronic components shop and buy three 3.5mm jacks and some wires to do a non-standard interconnection. You only need to capture two channels anyway: one from headphones and one from line output.
>> >> >> >> The appl_ptr can be placed in any position in the ring buffer for the >> >> application to write data but the sound card fetch data from this ring >> >> buffer sequentially, however snd_pcm_write() assume the maximum distance >> >> between appl_ptr and hwptr is only one buffer >> >> >> >> >> https://git.kernel.org/cgit/linux/kernel/git/tiwai/sound.git/commit/sound/pci/hda/hda_intel.c?id=2ae66c26550cd94b0e2606a9275eb0ab7070ad0e >> >> >> >> Do you mean hwptr does not decrease by one period when you use arbitrary >> >> period sizes for hda-Intel ? >> > >> > >> > I cannot comment on this commit. But >> "snd_hda_intel.align_buffer_size=1" indeed existed on my kernel command >> line (for no good reason now - so removed), and I don't use a strange >> period size. Loaded sound module options !!-------------------------- !!Module: snd_hda_intel align_buffer_size : -1 bdl_pos_adj : 32,32,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1 Why only one entry for align_buffer_size if it is specific to hda controller when the computer have two hda controllers ? https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/1324426 https://launchpadlibrarian.net/176540072/Symptom_PulseAudioLog.txt May 29 06:57:49 Lihkin pulseaudio[1874]: [alsa-sink-92HD81B1X5 Analog] alsa-sink.c: ALSA woke us up to write new data to the device, but there was actually nothing to write! Most likely this is a bug in the ALSA driver 'snd_hda_intel'. Please report this issue to the ALSA developers. We were woken up with POLLOUT set -- however a subsequent snd_pcm_avail() returned 0 or another value < min_avail. snd_pcm_avail() returned a value that is exceptionally large: 181132 bytes (1026 ms). Most likely this is a bug in the ALSA driver 'snd_hda_intel'. Please report this issue to the ALSA developers. Seem pulseaudio can use strange period size May 29 11:36:52 Lihkin pulseaudio[1306]: [alsa-sink-HDMI 0] alsa-util.c: Its setup is: stream : PLAYBACK access : MMAP_INTERLEAVED format : S16_LE subformat : STD channels : 2 rate : 44100 exact rate : 44100 (44100/1) msbits : 16 buffer_size : 3520 period_size : 352 period_time : 7981 tstamp_mode : ENABLE period_step : 1 avail_min : 352 period_event : 1 start_threshold : -1 stop_threshold : 7926335344172072960 silence_threshold: 0 silence_size : 0 boundary : 7926335344172072960 appl_ptr : 2916662 hw_ptr : 2958425 start_threshold : -1 This mean the playback will automatically start if pulseaudio write any audio data instead of start after write pre buffer Try aplay with any arbitrary period size/period time and xrun_debug , check whether hw_ptr is updated on every period update in the system log aplay -v --period-size=352 --buffer-size=3520 -Dhw:0,0 stereo.wav http://www.alsa-project.org/main/index.php/XRUN_Debug /proc/asound/card#/pcm0p/xrun_debug Replace '#' with your card number (usually 0). This proc file can enable various debugging tools. The CONFIG_SND_PCM_XRUN_DEBUG, CONFIG_SND_VERBOSE_PROCFS, CONFIG_SND_DEBUG options must be enabled in your kernel (if xrun_debug proc file is present - this feature is enabled). # Enable basic debugging, do jiffies check and dump position on each period and hardware pointer update calls # Usefull when the lowlevel (specific) hardware driver is somehow broken echo 29 > /proc/asound/card0/pcm0p/xrun_debug
diff --git a/sound/pci/hda/hda_proc.c b/sound/pci/hda/hda_proc.c index ce5a6da..65c1da9 100644 --- a/sound/pci/hda/hda_proc.c +++ b/sound/pci/hda/hda_proc.c @@ -482,6 +482,14 @@ static void print_power_state(struct snd_info_buffer *buffer, snd_iprintf(buffer, "\n"); } +static void print_afg_caps(struct snd_info_buffer *buffer, + struct hda_codec *codec, hda_nid_t nid) +{ + int afg_cap = snd_hda_param_read(codec, nid, AC_PAR_AUDIO_FG_CAP); + snd_iprintf(buffer, "0x%08x OutputDelay=0x%02x InputDelay=0x%02x BeepGen=%x\n", + afg_cap, afg_cap & 0xf, (afg_cap >> 8) & 0xf, (afg_cap >> 16) & 1); +} + static void print_unsol_cap(struct snd_info_buffer *buffer, struct hda_codec *codec, hda_nid_t nid) { @@ -682,6 +690,8 @@ static void print_codec_info(struct snd_info_entry *entry, print_amp_caps(buffer, codec, codec->afg, HDA_OUTPUT); snd_iprintf(buffer, "State of AFG node 0x%02x:\n", codec->afg); print_power_state(buffer, codec, codec->afg); + snd_iprintf(buffer, "AFG caps: "); + print_afg_caps(buffer, codec, codec->afg); nodes = snd_hda_get_sub_nodes(codec, codec->afg, &nid); if (! nid || nodes < 0) {