new file mode 100644
@@ -0,0 +1,88 @@
+Maxim MAX77802 multi-function device
+
+MAX77802 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is
+interfaced to host controller using i2c interface. PMIC, Charger and RTC
+submodules are addressed using same i2c slave address
+
+This document describes the binding for mfd device and PMIC submodule.
+
+Binding for the built-in 32k clock generator block is defined separately
+in bindings/clk/maxim,max77802.txt file.
+
+Required properties:
+- compatible : Must be "maxim,max77802";
+- reg : Specifies the i2c slave address of PMIC block.
+- interrupts : This i2c device has an IRQ line connected to the main SoC.
+- interrupt-parent : The parent interrupt controller.
+
+Optional properties:
+- max77802,pmic-buck-default-dvs-idx: We'll always write this DVS index in the
+ PMIC for BUCKs with DVS (Bucks 1-4, 6).
+ NOTE: at the moment these bindings don't include enough details for actual
+ GPIO-DVS--this just lets you choose which single slot to use.
+
+- max77802,pmic-buck-dvs-gpios: The DVS GPIOs. We'll try to set these GPIOs
+ to match pmic-buck-default-dvs-idx at probe time if they are defined. If
+ some or all of these GPIOs are not defined it's assumed that the board has
+ any missing GPIOs hardwired to match pmic-buck-default-dvs-idx.
+
+- max77802,pmic-buck-selb-gpios: GPIOs to enable DVS-GPIO for BUCKs.
+ Should be five values: 1, 2, 3, 4, 6. It is strongly suggested to include
+ these GPIOs if there's any chance that changing DVS GPIOs one line at a
+ time might glitch your DVS values.
+
+Optional node:
+- voltage-regulators : The regulators of max77802 have to be instantiated
+ under subnode named "voltage-regulators" using the following format.
+
+ regulator_name {
+ regulator-compatible = LDOn/BUCKn
+ standard regulator constraints....
+ };
+ refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+ The regulator-compatible property of regulator should initialized with string
+to get matched with their hardware counterparts as follow:
+
+ -LDOn : for LDOs, where n can lie in range 1 to 35.
+ example: LDO1, LDO2, LDO35.
+ -BUCKn : for BUCKs, where n can lie in range 1 to 10.
+ example: BUCK1, BUCK5, BUCK10.
+Example:
+
+ max77802@09 {
+ compatible = "maxim,max77802";
+ interrupt-parent = <&wakeup_eint>;
+ interrupts = <26 0>;
+ reg = <0x09>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ max77802,pmic-buck-default-dvs-idx = <1>;
+ max77802,pmic-buck-dvs-gpios = <&gpy7 6 0>,
+ <&gpj4 2 0>,
+ <&gpj4 3 0>;
+ max77802,pmic-buck-selb-gpios = <&gph0 2 0>,
+ <&gph0 3 0>,
+ <&gph0 4 0>,
+ <&gph0 5 0>,
+ <&gph0 6 0>;
+
+ voltage-regulators {
+ ldo11_reg {
+ regulator-compatible = "LDO11";
+ regulator-name = "vdd_ldo11";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-always-on;
+ };
+
+ buck1_reg {
+ regulator-compatible = "BUCK1";
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
@@ -392,6 +392,19 @@ config MFD_MAX77693
additional drivers must be enabled in order to use the functionality
of the device.
+config MFD_MAX77802
+ bool "Maxim Integrated MAX77802 PMIC Support"
+ depends on I2C=y
+ select MFD_CORE
+ select REGMAP_I2C
+ select IRQ_DOMAIN
+ help
+ Say yes here to support for Maxim Integrated MAX77802.
+ This is a Power Management IC with RTC on chip.
+ This driver provides common support for accessing the device;
+ additional drivers must be enabled in order to use the functionality
+ of the device.
+
config MFD_MAX8907
tristate "Maxim Semiconductor MAX8907 PMIC Support"
select MFD_CORE
@@ -117,6 +117,7 @@ obj-$(CONFIG_MFD_DA9063) += da9063.o
obj-$(CONFIG_MFD_MAX14577) += max14577.o
obj-$(CONFIG_MFD_MAX77686) += max77686.o max77686-irq.o
obj-$(CONFIG_MFD_MAX77693) += max77693.o max77693-irq.o
+obj-$(CONFIG_MFD_MAX77802) += max77802.o max77802-irq.o
obj-$(CONFIG_MFD_MAX8907) += max8907.o
max8925-objs := max8925-core.o max8925-i2c.o
obj-$(CONFIG_MFD_MAX8925) += max8925.o
new file mode 100644
@@ -0,0 +1,332 @@
+/*
+ * max77802-irq.c - Interrupt controller support for MAX77802
+ *
+ * Copyright (C) 2013-2014 Google, Inc
+ *
+ * Copyright (C) 2012 Samsung Electronics Co.Ltd
+ * Chiwoong Byun <woong.byun@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * This driver is based on max8997-irq.c
+ */
+
+#include <linux/err.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <linux/mfd/max77802.h>
+#include <linux/mfd/max77802-private.h>
+#include <linux/irqdomain.h>
+#include <linux/regmap.h>
+
+enum {
+ MAX77802_DEBUG_IRQ_INFO = 1 << 0,
+ MAX77802_DEBUG_IRQ_MASK = 1 << 1,
+ MAX77802_DEBUG_IRQ_INT = 1 << 2,
+};
+
+static int debug_mask = 0;
+module_param(debug_mask, int, 0);
+MODULE_PARM_DESC(debug_mask, "Set debug_mask : 0x0=off 0x1=IRQ_INFO 0x2=IRQ_MASK 0x4=IRQ_INI)");
+
+static const u8 max77802_mask_reg[] = {
+ [PMIC_INT1] = MAX77802_REG_INT1MSK,
+ [PMIC_INT2] = MAX77802_REG_INT2MSK,
+ [RTC_INT] = MAX77802_RTC_INTM,
+};
+
+struct max77802_irq_data {
+ int mask;
+ enum max77802_irq_source group;
+};
+
+#define DECLARE_IRQ(idx, _group, _mask) \
+ [(idx)] = { .group = (_group), .mask = (_mask) }
+static const struct max77802_irq_data max77802_irqs[] = {
+ DECLARE_IRQ(MAX77802_PMICIRQ_PWRONF, PMIC_INT1, 1 << 0),
+ DECLARE_IRQ(MAX77802_PMICIRQ_PWRONR, PMIC_INT1, 1 << 1),
+ DECLARE_IRQ(MAX77802_PMICIRQ_JIGONBF, PMIC_INT1, 1 << 2),
+ DECLARE_IRQ(MAX77802_PMICIRQ_JIGONBR, PMIC_INT1, 1 << 3),
+ DECLARE_IRQ(MAX77802_PMICIRQ_ACOKBF, PMIC_INT1, 1 << 4),
+ DECLARE_IRQ(MAX77802_PMICIRQ_ACOKBR, PMIC_INT1, 1 << 5),
+ DECLARE_IRQ(MAX77802_PMICIRQ_ONKEY1S, PMIC_INT1, 1 << 6),
+ DECLARE_IRQ(MAX77802_PMICIRQ_MRSTB, PMIC_INT1, 1 << 7),
+ DECLARE_IRQ(MAX77802_PMICIRQ_140C, PMIC_INT2, 1 << 0),
+ DECLARE_IRQ(MAX77802_PMICIRQ_120C, PMIC_INT2, 1 << 1),
+ DECLARE_IRQ(MAX77802_RTCIRQ_RTC60S, RTC_INT, 1 << 0),
+ DECLARE_IRQ(MAX77802_RTCIRQ_RTCA1, RTC_INT, 1 << 1),
+ DECLARE_IRQ(MAX77802_RTCIRQ_RTCA2, RTC_INT, 1 << 2),
+ DECLARE_IRQ(MAX77802_RTCIRQ_SMPL, RTC_INT, 1 << 3),
+ DECLARE_IRQ(MAX77802_RTCIRQ_RTC1S, RTC_INT, 1 << 4),
+ DECLARE_IRQ(MAX77802_RTCIRQ_WTSR, RTC_INT, 1 << 5),
+};
+
+static void max77802_irq_lock(struct irq_data *data)
+{
+ struct max77802_dev *max77802 = irq_get_chip_data(data->irq);
+
+ if (debug_mask & MAX77802_DEBUG_IRQ_MASK)
+ pr_info("%s\n", __func__);
+
+ mutex_lock(&max77802->irqlock);
+}
+
+static void max77802_irq_sync_unlock(struct irq_data *data)
+{
+ struct max77802_dev *max77802 = irq_get_chip_data(data->irq);
+ int i;
+
+ for (i = 0; i < MAX77802_IRQ_GROUP_NR; i++) {
+ u8 mask_reg = max77802_mask_reg[i];
+
+ if (debug_mask & MAX77802_DEBUG_IRQ_MASK)
+ pr_debug("%s: mask_reg[%d]=0x%x, cur=0x%x\n",
+ __func__, i, mask_reg, max77802->irq_masks_cur[i]);
+
+ if (mask_reg == MAX77802_REG_INVALID ||
+ IS_ERR_OR_NULL(max77802->regmap))
+ continue;
+
+ max77802->irq_masks_cache[i] = max77802->irq_masks_cur[i];
+
+ regmap_write(max77802->regmap, mask_reg,
+ max77802->irq_masks_cur[i]);
+ }
+
+ mutex_unlock(&max77802->irqlock);
+}
+
+static const inline struct max77802_irq_data *to_max77802_irq(int irq)
+{
+ struct irq_data *data = irq_get_irq_data(irq);
+ return &max77802_irqs[data->hwirq];
+}
+
+static void max77802_irq_mask(struct irq_data *data)
+{
+ struct max77802_dev *max77802 = irq_get_chip_data(data->irq);
+ const struct max77802_irq_data *irq_data = to_max77802_irq(data->irq);
+
+ max77802->irq_masks_cur[irq_data->group] |= irq_data->mask;
+
+ if (debug_mask & MAX77802_DEBUG_IRQ_MASK)
+ pr_info("%s: group=%d, cur=0x%x\n",
+ __func__, irq_data->group,
+ max77802->irq_masks_cur[irq_data->group]);
+}
+
+static void max77802_irq_unmask(struct irq_data *data)
+{
+ struct max77802_dev *max77802 = irq_get_chip_data(data->irq);
+ const struct max77802_irq_data *irq_data = to_max77802_irq(data->irq);
+
+ max77802->irq_masks_cur[irq_data->group] &= ~irq_data->mask;
+
+ if (debug_mask & MAX77802_DEBUG_IRQ_MASK)
+ pr_info("%s: group=%d, cur=0x%x\n",
+ __func__, irq_data->group,
+ max77802->irq_masks_cur[irq_data->group]);
+}
+
+static int max77802_irq_set_wake(struct irq_data *data, unsigned int on)
+{
+ struct max77802_dev *max77802 = irq_get_chip_data(data->irq);
+
+ if (device_may_wakeup(max77802->dev)) {
+ if (on)
+ return enable_irq_wake(max77802->irq);
+ else
+ return disable_irq_wake(max77802->irq);
+ } else if (on) {
+ dev_warn(max77802->dev,
+ "Child requested wakeup but wakeup disabled\n");
+ return -ENXIO;
+ }
+ return 0;
+}
+
+static struct irq_chip max77802_irq_chip = {
+ .name = "max77802",
+ .irq_bus_lock = max77802_irq_lock,
+ .irq_bus_sync_unlock = max77802_irq_sync_unlock,
+ .irq_mask = max77802_irq_mask,
+ .irq_unmask = max77802_irq_unmask,
+ .irq_set_wake = max77802_irq_set_wake,
+};
+
+static irqreturn_t max77802_irq_thread(int irq, void *data)
+{
+ struct max77802_dev *max77802 = data;
+ unsigned int irq_reg[MAX77802_IRQ_GROUP_NR] = {};
+ unsigned int irq_src;
+ int ret;
+ int i, cur_irq;
+
+ ret = regmap_read(max77802->regmap, MAX77802_REG_INTSRC, &irq_src);
+ if (ret < 0) {
+ dev_err(max77802->dev, "Failed to read interrupt source: %d\n",
+ ret);
+ return IRQ_NONE;
+ }
+
+ if (debug_mask & MAX77802_DEBUG_IRQ_INT)
+ pr_info("%s: irq_src=0x%x\n", __func__, irq_src);
+
+ if (irq_src == MAX77802_IRQSRC_PMIC) {
+ ret = regmap_bulk_read(max77802->regmap,
+ MAX77802_REG_INT1, irq_reg, 2);
+ if (ret < 0) {
+ dev_err(max77802->dev, "Failed to read interrupt source: %d\n",
+ ret);
+ return IRQ_NONE;
+ }
+
+ if (debug_mask & MAX77802_DEBUG_IRQ_INT)
+ pr_info("%s: int1=0x%x, int2=0x%x\n", __func__,
+ irq_reg[PMIC_INT1], irq_reg[PMIC_INT2]);
+ }
+
+ if (irq_src & MAX77802_IRQSRC_RTC) {
+ ret = regmap_read(max77802->regmap,
+ MAX77802_RTC_INT, &irq_reg[RTC_INT]);
+ if (ret < 0) {
+ dev_err(max77802->dev, "Failed to read interrupt source: %d\n",
+ ret);
+ return IRQ_NONE;
+ }
+
+ if (debug_mask & MAX77802_DEBUG_IRQ_INT)
+ pr_info("%s: rtc int=0x%x\n", __func__,
+ irq_reg[RTC_INT]);
+
+ }
+
+ for (i = 0; i < MAX77802_IRQ_GROUP_NR; i++)
+ irq_reg[i] &= ~max77802->irq_masks_cur[i];
+
+ for (i = 0; i < MAX77802_IRQ_NR; i++) {
+ if (irq_reg[max77802_irqs[i].group] & max77802_irqs[i].mask) {
+ cur_irq = irq_find_mapping(max77802->irq_domain, i);
+ if (cur_irq)
+ handle_nested_irq(cur_irq);
+ }
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int max77802_irq_domain_map(struct irq_domain *d, unsigned int irq,
+ irq_hw_number_t hw)
+{
+ struct max77802_dev *max77802 = d->host_data;
+
+ irq_set_chip_data(irq, max77802);
+ irq_set_chip_and_handler(irq, &max77802_irq_chip, handle_simple_irq);
+ irq_set_nested_thread(irq, 1);
+ irq_set_parent(irq, max77802->irq);
+#ifdef CONFIG_ARM
+ set_irq_flags(irq, IRQF_VALID);
+#else
+ irq_set_noprobe(irq);
+#endif
+ return 0;
+}
+
+static struct irq_domain_ops max77802_irq_domain_ops = {
+ .map = max77802_irq_domain_map,
+};
+
+int max77802_irq_init(struct max77802_dev *max77802)
+{
+ struct irq_domain *domain;
+ int i;
+ int ret;
+ int val;
+
+ mutex_init(&max77802->irqlock);
+
+ if (max77802->irq_gpio && !max77802->irq) {
+ max77802->irq = gpio_to_irq(max77802->irq_gpio);
+
+ if (debug_mask & MAX77802_DEBUG_IRQ_INT) {
+ ret = gpio_request(max77802->irq_gpio, "pmic_irq");
+ if (ret < 0) {
+ dev_err(max77802->dev,
+ "Failed to request gpio %d with ret:"
+ "%d\n", max77802->irq_gpio, ret);
+ return IRQ_NONE;
+ }
+
+ gpio_direction_input(max77802->irq_gpio);
+ val = gpio_get_value(max77802->irq_gpio);
+ gpio_free(max77802->irq_gpio);
+ pr_info("%s: gpio_irq=%x\n", __func__, val);
+ }
+ }
+
+ if (!max77802->irq) {
+ dev_err(max77802->dev, "irq is not specified\n");
+ return -ENODEV;
+ }
+
+ /* Mask individual interrupt sources */
+ for (i = 0; i < MAX77802_IRQ_GROUP_NR; i++) {
+ max77802->irq_masks_cur[i] = 0xff;
+ max77802->irq_masks_cache[i] = 0xff;
+
+ if (IS_ERR_OR_NULL(max77802->regmap))
+ continue;
+ if (max77802_mask_reg[i] == MAX77802_REG_INVALID)
+ continue;
+
+ regmap_write(max77802->regmap, max77802_mask_reg[i], 0xff);
+ }
+ domain = irq_domain_add_linear(NULL, MAX77802_IRQ_NR,
+ &max77802_irq_domain_ops, max77802);
+ if (!domain) {
+ dev_err(max77802->dev, "could not create irq domain\n");
+ return -ENODEV;
+ }
+ max77802->irq_domain = domain;
+
+ ret = request_threaded_irq(max77802->irq, NULL, max77802_irq_thread,
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "max77802-irq", max77802);
+
+ if (ret)
+ dev_err(max77802->dev, "Failed to request IRQ %d: %d\n",
+ max77802->irq, ret);
+
+
+ if (debug_mask & MAX77802_DEBUG_IRQ_INFO)
+ pr_info("%s-\n", __func__);
+
+ return 0;
+}
+
+void max77802_irq_exit(struct max77802_dev *max77802)
+{
+ if (max77802->irq)
+ free_irq(max77802->irq, max77802);
+}
+
+int max77802_irq_resume(struct max77802_dev *max77802)
+{
+ /*
+ * The IRQ that woke us up may still need to be ACK'ed on resume.
+ * If it isn't ever ACK'ed, future IRQs may not be delivered.
+ */
+ if (max77802->irq)
+ max77802_irq_thread(0, max77802);
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,282 @@
+/*
+ * max77802.c - mfd core driver for the Maxim 77802
+ *
+ * Copyright (C) 2013-2014 Google, Inc
+ * Simon Glass <sjg@chromium.org>
+ *
+ * Copyright (C) 2012 Samsung Electronics
+ * Chiwoong Byun <woong.byun@smasung.com>
+ * Jonghwa Lee <jonghwa3.lee@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * This driver is based on max8997.c
+ */
+
+#include <linux/export.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/pm_runtime.h>
+#include <linux/module.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/max77802.h>
+#include <linux/mfd/max77802-private.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/err.h>
+
+static const struct mfd_cell max77802_devs[] = {
+ { .name = "max77802-pmic", },
+};
+
+static bool max77802_pmic_is_accessible_reg(struct device *dev,
+ unsigned int reg)
+{
+ return (reg >= MAX77802_REG_DEVICE_ID && reg < MAX77802_REG_PMIC_END);
+}
+
+static bool max77802_rtc_is_accessible_reg(struct device *dev,
+ unsigned int reg)
+{
+ return (reg >= MAX77802_RTC_INT && reg < MAX77802_RTC_END);
+}
+
+static bool max77802_is_accessible_reg(struct device *dev, unsigned int reg)
+{
+ return (max77802_pmic_is_accessible_reg(dev, reg) ||
+ max77802_rtc_is_accessible_reg(dev, reg));
+}
+
+static bool max77802_pmic_is_precious_reg(struct device *dev, unsigned int reg)
+{
+ return (reg == MAX77802_REG_INTSRC || reg == MAX77802_REG_INT1 ||
+ reg == MAX77802_REG_INT2);
+}
+
+static bool max77802_rtc_is_precious_reg(struct device *dev, unsigned int reg)
+{
+ return (reg == MAX77802_RTC_INT ||
+ reg == MAX77802_RTC_UPDATE0 ||
+ reg == MAX77802_RTC_UPDATE1);
+}
+
+static bool max77802_is_precious_reg(struct device *dev, unsigned int reg)
+{
+ return (max77802_pmic_is_precious_reg(dev, reg) ||
+ max77802_rtc_is_precious_reg(dev, reg));
+}
+
+static bool max77802_pmic_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ return (max77802_is_precious_reg(dev, reg) ||
+ reg == MAX77802_REG_STATUS1 || reg == MAX77802_REG_STATUS2 ||
+ reg == MAX77802_REG_PWRON);
+}
+
+static bool max77802_rtc_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ return (max77802_rtc_is_precious_reg(dev, reg) ||
+ reg == MAX77802_RTC_SEC ||
+ reg == MAX77802_RTC_MIN ||
+ reg == MAX77802_RTC_HOUR ||
+ reg == MAX77802_RTC_WEEKDAY ||
+ reg == MAX77802_RTC_MONTH ||
+ reg == MAX77802_RTC_YEAR ||
+ reg == MAX77802_RTC_DATE);
+}
+
+static bool max77802_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ return (max77802_pmic_is_volatile_reg(dev, reg) ||
+ max77802_rtc_is_volatile_reg(dev, reg));
+}
+
+static struct regmap_config max77802_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .writeable_reg = max77802_is_accessible_reg,
+ .readable_reg = max77802_is_accessible_reg,
+ .precious_reg = max77802_is_precious_reg,
+ .volatile_reg = max77802_is_volatile_reg,
+ .name = "max77802-pmic",
+ .cache_type = REGCACHE_RBTREE,
+};
+
+#ifdef CONFIG_OF
+static struct of_device_id max77802_pmic_dt_match[] = {
+ {.compatible = "maxim,max77802", .data = NULL},
+ {},
+};
+
+static void max77802_dt_parse_dvs_gpio(struct device *dev,
+ struct max77802_platform_data *pd,
+ struct device_node *np)
+{
+ int i;
+
+ /*
+ * NOTE: we don't consider GPIO errors fatal; board may have some lines
+ * directly pulled high or low and thus doesn't specify them.
+ */
+ for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_dvs); i++)
+ pd->buck_gpio_dvs[i] =
+ of_get_named_gpio(np,
+ "max77802,pmic-buck-dvs-gpios", i);
+
+ for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_selb); i++)
+ pd->buck_gpio_selb[i] =
+ of_get_named_gpio(np,
+ "max77802,pmic-buck-selb-gpios", i);
+}
+
+static struct max77802_platform_data *max77802_i2c_parse_dt_pdata(struct device
+ *dev)
+{
+ struct device_node *np = dev->of_node;
+ struct max77802_platform_data *pd;
+
+ pd = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL);
+ if (!pd) {
+ dev_err(dev, "could not allocate memory for pdata\n");
+ return NULL;
+ }
+
+ /* Read default index and ignore errors, since default is 0 */
+ of_property_read_u32(np, "max77802,pmic-buck-default-dvs-idx",
+ &pd->buck_default_idx);
+
+ max77802_dt_parse_dvs_gpio(dev, pd, np);
+
+ dev->platform_data = pd;
+ return pd;
+}
+#else
+static struct max77802_platform_data *max77802_i2c_parse_dt_pdata(struct device
+ *dev)
+{
+ return 0;
+}
+#endif
+
+static int max77802_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct max77802_dev *max77802 = NULL;
+ struct max77802_platform_data *pdata = dev_get_platdata(&i2c->dev);
+ unsigned int data;
+ int ret = 0;
+
+ if (i2c->dev.of_node)
+ pdata = max77802_i2c_parse_dt_pdata(&i2c->dev);
+
+ if (!pdata) {
+ dev_err(&i2c->dev, "No platform data found.\n");
+ return -EIO;
+ }
+
+ max77802 = devm_kzalloc(&i2c->dev, sizeof(struct max77802_dev),
+ GFP_KERNEL);
+ if (max77802 == NULL)
+ return -ENOMEM;
+
+ i2c_set_clientdata(i2c, max77802);
+ max77802->dev = &i2c->dev;
+ max77802->i2c = i2c;
+ max77802->type = id->driver_data;
+
+ max77802->wakeup = pdata->wakeup;
+ max77802->irq_gpio = pdata->irq_gpio;
+ max77802->irq = i2c->irq;
+
+ max77802->regmap = devm_regmap_init_i2c(i2c, &max77802_regmap_config);
+ if (IS_ERR(max77802->regmap)) {
+ ret = PTR_ERR(max77802->regmap);
+ dev_err(max77802->dev, "Failed to allocate register map: %d\n",
+ ret);
+ return ret;
+ }
+
+ if (regmap_read(max77802->regmap,
+ MAX77802_REG_DEVICE_ID, &data) < 0) {
+ dev_err(max77802->dev,
+ "device not found on this channel (this is not an error)\n");
+ return -ENODEV;
+ } else {
+ dev_info(max77802->dev, "device found\n");
+ }
+
+ max77802_irq_init(max77802);
+
+ ret = mfd_add_devices(max77802->dev, -1, max77802_devs,
+ ARRAY_SIZE(max77802_devs), NULL, 0, NULL);
+ if (ret < 0)
+ mfd_remove_devices(max77802->dev);
+
+ return ret;
+}
+
+static int max77802_i2c_remove(struct i2c_client *i2c)
+{
+ struct max77802_dev *max77802 = i2c_get_clientdata(i2c);
+
+ mfd_remove_devices(max77802->dev);
+
+ return 0;
+}
+
+static const struct i2c_device_id max77802_i2c_id[] = {
+ { "max77802", TYPE_MAX77802 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, max77802_i2c_id);
+
+#ifdef CONFIG_PM_SLEEP
+static int max77802_resume(struct device *dev)
+{
+ struct i2c_client *i2c = container_of(dev, struct i2c_client, dev);
+ struct max77802_dev *max77802 = i2c_get_clientdata(i2c);
+
+ max77802_irq_resume(max77802);
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(max77802_pm_ops, NULL, max77802_resume);
+
+static struct i2c_driver max77802_i2c_driver = {
+ .driver = {
+ .name = "max77802",
+ .owner = THIS_MODULE,
+ .pm = &max77802_pm_ops,
+ .of_match_table = of_match_ptr(max77802_pmic_dt_match),
+ },
+ .probe = max77802_i2c_probe,
+ .remove = max77802_i2c_remove,
+ .id_table = max77802_i2c_id,
+};
+
+static int __init max77802_i2c_init(void)
+{
+ return i2c_add_driver(&max77802_i2c_driver);
+}
+/* init early so consumer devices can complete system boot */
+subsys_initcall(max77802_i2c_init);
+
+static void __exit max77802_i2c_exit(void)
+{
+ i2c_del_driver(&max77802_i2c_driver);
+}
+module_exit(max77802_i2c_exit);
+
+MODULE_DESCRIPTION("MAXIM 77802 multi-function core driver");
+MODULE_AUTHOR("Simon Glass <sjg@chromium.org>");
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,291 @@
+/*
+ * max77802-private.h - Voltage regulator driver for the Maxim 77802
+ *
+ * Copyright (C) 2012 Samsung Electrnoics
+ * Chiwoong Byun <woong.byun@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __LINUX_MFD_MAX77802_PRIV_H
+#define __LINUX_MFD_MAX77802_PRIV_H
+
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/module.h>
+
+#define MAX77802_REG_INVALID (0xff)
+
+enum max77802_pmic_reg {
+ MAX77802_REG_DEVICE_ID = 0x00,
+ MAX77802_REG_INTSRC = 0x01,
+ MAX77802_REG_INT1 = 0x02,
+ MAX77802_REG_INT2 = 0x03,
+
+ MAX77802_REG_INT1MSK = 0x04,
+ MAX77802_REG_INT2MSK = 0x05,
+
+ MAX77802_REG_STATUS1 = 0x06,
+ MAX77802_REG_STATUS2 = 0x07,
+
+ MAX77802_REG_PWRON = 0x08,
+ /* Reserved: 0x09 */
+ MAX77802_REG_MRSTB = 0x0A,
+ MAX77802_REG_EPWRHOLD = 0x0B,
+ /* Reserved: 0x0C-0x0D */
+ MAX77802_REG_BOOSTCTRL = 0x0E,
+ MAX77802_REG_BOOSTOUT = 0x0F,
+
+ MAX77802_REG_BUCK1CTRL = 0x10,
+ MAX77802_REG_BUCK1DVS1 = 0x11,
+ MAX77802_REG_BUCK1DVS2 = 0x12,
+ MAX77802_REG_BUCK1DVS3 = 0x13,
+ MAX77802_REG_BUCK1DVS4 = 0x14,
+ MAX77802_REG_BUCK1DVS5 = 0x15,
+ MAX77802_REG_BUCK1DVS6 = 0x16,
+ MAX77802_REG_BUCK1DVS7 = 0x17,
+ MAX77802_REG_BUCK1DVS8 = 0x18,
+ /* Reserved: 0x19 */
+ MAX77802_REG_BUCK2CTRL1 = 0x1A,
+ MAX77802_REG_BUCK2CTRL2 = 0x1B,
+ MAX77802_REG_BUCK2PHTRAN = 0x1C,
+ MAX77802_REG_BUCK2DVS1 = 0x1D,
+ MAX77802_REG_BUCK2DVS2 = 0x1E,
+ MAX77802_REG_BUCK2DVS3 = 0x1F,
+ MAX77802_REG_BUCK2DVS4 = 0x20,
+ MAX77802_REG_BUCK2DVS5 = 0x21,
+ MAX77802_REG_BUCK2DVS6 = 0x22,
+ MAX77802_REG_BUCK2DVS7 = 0x23,
+ MAX77802_REG_BUCK2DVS8 = 0x24,
+ /* Reserved: 0x25-0x26 */
+ MAX77802_REG_BUCK3CTRL1 = 0x27,
+ MAX77802_REG_BUCK3DVS1 = 0x28,
+ MAX77802_REG_BUCK3DVS2 = 0x29,
+ MAX77802_REG_BUCK3DVS3 = 0x2A,
+ MAX77802_REG_BUCK3DVS4 = 0x2B,
+ MAX77802_REG_BUCK3DVS5 = 0x2C,
+ MAX77802_REG_BUCK3DVS6 = 0x2D,
+ MAX77802_REG_BUCK3DVS7 = 0x2E,
+ MAX77802_REG_BUCK3DVS8 = 0x2F,
+ /* Reserved: 0x30-0x36 */
+ MAX77802_REG_BUCK4CTRL1 = 0x37,
+ MAX77802_REG_BUCK4DVS1 = 0x38,
+ MAX77802_REG_BUCK4DVS2 = 0x39,
+ MAX77802_REG_BUCK4DVS3 = 0x3A,
+ MAX77802_REG_BUCK4DVS4 = 0x3B,
+ MAX77802_REG_BUCK4DVS5 = 0x3C,
+ MAX77802_REG_BUCK4DVS6 = 0x3D,
+ MAX77802_REG_BUCK4DVS7 = 0x3E,
+ MAX77802_REG_BUCK4DVS8 = 0x3F,
+ /* Reserved: 0x40 */
+ MAX77802_REG_BUCK5CTRL = 0x41,
+ MAX77802_REG_BUCK5OUT = 0x42,
+ /* Reserved: 0x43 */
+ MAX77802_REG_BUCK6CTRL = 0x44,
+ MAX77802_REG_BUCK6DVS1 = 0x45,
+ MAX77802_REG_BUCK6DVS2 = 0x46,
+ MAX77802_REG_BUCK6DVS3 = 0x47,
+ MAX77802_REG_BUCK6DVS4 = 0x48,
+ MAX77802_REG_BUCK6DVS5 = 0x49,
+ MAX77802_REG_BUCK6DVS6 = 0x4A,
+ MAX77802_REG_BUCK6DVS7 = 0x4B,
+ MAX77802_REG_BUCK6DVS8 = 0x4C,
+ /* Reserved: 0x4D */
+ MAX77802_REG_BUCK7CTRL = 0x4E,
+ MAX77802_REG_BUCK7OUT = 0x4F,
+ /* Reserved: 0x50 */
+ MAX77802_REG_BUCK8CTRL = 0x51,
+ MAX77802_REG_BUCK8OUT = 0x52,
+ /* Reserved: 0x53 */
+ MAX77802_REG_BUCK9CTRL = 0x54,
+ MAX77802_REG_BUCK9OUT = 0x55,
+ /* Reserved: 0x56 */
+ MAX77802_REG_BUCK10CTRL = 0x57,
+ MAX77802_REG_BUCK10OUT = 0x58,
+
+ /* Reserved: 0x59-0x5F */
+
+ MAX77802_REG_LDO1CTRL1 = 0x60,
+ MAX77802_REG_LDO2CTRL1 = 0x61,
+ MAX77802_REG_LDO3CTRL1 = 0x62,
+ MAX77802_REG_LDO4CTRL1 = 0x63,
+ MAX77802_REG_LDO5CTRL1 = 0x64,
+ MAX77802_REG_LDO6CTRL1 = 0x65,
+ MAX77802_REG_LDO7CTRL1 = 0x66,
+ MAX77802_REG_LDO8CTRL1 = 0x67,
+ MAX77802_REG_LDO9CTRL1 = 0x68,
+ MAX77802_REG_LDO10CTRL1 = 0x69,
+ MAX77802_REG_LDO11CTRL1 = 0x6A,
+ MAX77802_REG_LDO12CTRL1 = 0x6B,
+ MAX77802_REG_LDO13CTRL1 = 0x6C,
+ MAX77802_REG_LDO14CTRL1 = 0x6D,
+ MAX77802_REG_LDO15CTRL1 = 0x6E,
+ /* Reserved: 0x6F */
+ MAX77802_REG_LDO17CTRL1 = 0x70,
+ MAX77802_REG_LDO18CTRL1 = 0x71,
+ MAX77802_REG_LDO19CTRL1 = 0x72,
+ MAX77802_REG_LDO20CTRL1 = 0x73,
+ MAX77802_REG_LDO21CTRL1 = 0x74,
+ MAX77802_REG_LDO22CTRL1 = 0x75,
+ MAX77802_REG_LDO23CTRL1 = 0x76,
+ MAX77802_REG_LDO24CTRL1 = 0x77,
+ MAX77802_REG_LDO25CTRL1 = 0x78,
+ MAX77802_REG_LDO26CTRL1 = 0x79,
+ MAX77802_REG_LDO27CTRL1 = 0x7A,
+ MAX77802_REG_LDO28CTRL1 = 0x7B,
+ MAX77802_REG_LDO29CTRL1 = 0x7C,
+ MAX77802_REG_LDO30CTRL1 = 0x7D,
+ /* Reserved: 0x7E */
+ MAX77802_REG_LDO32CTRL1 = 0x7F,
+ MAX77802_REG_LDO33CTRL1 = 0x80,
+ MAX77802_REG_LDO34CTRL1 = 0x81,
+ MAX77802_REG_LDO35CTRL1 = 0x82,
+ /* Reserved: 0x83-0x8F */
+ MAX77802_REG_LDO1CTRL2 = 0x90,
+ MAX77802_REG_LDO2CTRL2 = 0x91,
+ MAX77802_REG_LDO3CTRL2 = 0x92,
+ MAX77802_REG_LDO4CTRL2 = 0x93,
+ MAX77802_REG_LDO5CTRL2 = 0x94,
+ MAX77802_REG_LDO6CTRL2 = 0x95,
+ MAX77802_REG_LDO7CTRL2 = 0x96,
+ MAX77802_REG_LDO8CTRL2 = 0x97,
+ MAX77802_REG_LDO9CTRL2 = 0x98,
+ MAX77802_REG_LDO10CTRL2 = 0x99,
+ MAX77802_REG_LDO11CTRL2 = 0x9A,
+ MAX77802_REG_LDO12CTRL2 = 0x9B,
+ MAX77802_REG_LDO13CTRL2 = 0x9C,
+ MAX77802_REG_LDO14CTRL2 = 0x9D,
+ MAX77802_REG_LDO15CTRL2 = 0x9E,
+ /* Reserved: 0x9F */
+ MAX77802_REG_LDO17CTRL2 = 0xA0,
+ MAX77802_REG_LDO18CTRL2 = 0xA1,
+ MAX77802_REG_LDO19CTRL2 = 0xA2,
+ MAX77802_REG_LDO20CTRL2 = 0xA3,
+ MAX77802_REG_LDO21CTRL2 = 0xA4,
+ MAX77802_REG_LDO22CTRL2 = 0xA5,
+ MAX77802_REG_LDO23CTRL2 = 0xA6,
+ MAX77802_REG_LDO24CTRL2 = 0xA7,
+ MAX77802_REG_LDO25CTRL2 = 0xA8,
+ MAX77802_REG_LDO26CTRL2 = 0xA9,
+ MAX77802_REG_LDO27CTRL2 = 0xAA,
+ MAX77802_REG_LDO28CTRL2 = 0xAB,
+ MAX77802_REG_LDO29CTRL2 = 0xAC,
+ MAX77802_REG_LDO30CTRL2 = 0xAD,
+ /* Reserved: 0xAE */
+ MAX77802_REG_LDO32CTRL2 = 0xAF,
+ MAX77802_REG_LDO33CTRL2 = 0xB0,
+ MAX77802_REG_LDO34CTRL2 = 0xB1,
+ MAX77802_REG_LDO35CTRL2 = 0xB2,
+ /* Reserved: 0xB3 */
+
+ MAX77802_REG_BBAT_CHG = 0xB4,
+ MAX77802_REG_32KHZ = 0xB5,
+
+ MAX77802_REG_PMIC_END = 0xB6,
+};
+
+enum max77802_rtc_reg {
+ MAX77802_RTC_INT = 0xC0,
+ MAX77802_RTC_INTM = 0xC1,
+ MAX77802_RTC_CONTROLM = 0xC2,
+ MAX77802_RTC_CONTROL = 0xC3,
+ MAX77802_RTC_UPDATE0 = 0xC4,
+ MAX77802_RTC_UPDATE1 = 0xC5,
+ MAX77802_WTSR_SMPL_CNTL = 0xC6,
+ MAX77802_RTC_SEC = 0xC7,
+ MAX77802_RTC_MIN = 0xC8,
+ MAX77802_RTC_HOUR = 0xC9,
+ MAX77802_RTC_WEEKDAY = 0xCA,
+ MAX77802_RTC_MONTH = 0xCB,
+ MAX77802_RTC_YEAR = 0xCC,
+ MAX77802_RTC_DATE = 0xCD,
+ MAX77802_RTC_AE1 = 0xCE,
+ MAX77802_ALARM1_SEC = 0xCF,
+ MAX77802_ALARM1_MIN = 0xD0,
+ MAX77802_ALARM1_HOUR = 0xD1,
+ MAX77802_ALARM1_WEEKDAY = 0xD2,
+ MAX77802_ALARM1_MONTH = 0xD3,
+ MAX77802_ALARM1_YEAR = 0xD4,
+ MAX77802_ALARM1_DATE = 0xD5,
+ MAX77802_RTC_AE2 = 0xD6,
+ MAX77802_ALARM2_SEC = 0xD7,
+ MAX77802_ALARM2_MIN = 0xD8,
+ MAX77802_ALARM2_HOUR = 0xD9,
+ MAX77802_ALARM2_WEEKDAY = 0xDA,
+ MAX77802_ALARM2_MONTH = 0xDB,
+ MAX77802_ALARM2_YEAR = 0xDC,
+ MAX77802_ALARM2_DATE = 0xDD,
+
+ MAX77802_RTC_END = 0xDF,
+};
+
+#define MAX77802_IRQSRC_PMIC (0)
+#define MAX77802_IRQSRC_RTC (1 << 0)
+
+enum max77802_irq_source {
+ PMIC_INT1 = 0,
+ PMIC_INT2,
+ RTC_INT,
+
+ MAX77802_IRQ_GROUP_NR,
+};
+
+enum max77802_irq {
+ MAX77802_PMICIRQ_PWRONF,
+ MAX77802_PMICIRQ_PWRONR,
+ MAX77802_PMICIRQ_JIGONBF,
+ MAX77802_PMICIRQ_JIGONBR,
+ MAX77802_PMICIRQ_ACOKBF,
+ MAX77802_PMICIRQ_ACOKBR,
+ MAX77802_PMICIRQ_ONKEY1S,
+ MAX77802_PMICIRQ_MRSTB,
+
+ MAX77802_PMICIRQ_140C,
+ MAX77802_PMICIRQ_120C,
+
+ MAX77802_RTCIRQ_RTC60S,
+ MAX77802_RTCIRQ_RTCA1,
+ MAX77802_RTCIRQ_RTCA2,
+ MAX77802_RTCIRQ_SMPL,
+ MAX77802_RTCIRQ_RTC1S,
+ MAX77802_RTCIRQ_WTSR,
+
+ MAX77802_IRQ_NR,
+};
+
+struct max77802_dev {
+ struct device *dev;
+ struct i2c_client *i2c; /* 0x09 / PMIC, Battery Control and RTC */
+
+ int type;
+
+ struct regmap *regmap; /* regmap for mfd and rtc devices */
+
+ struct irq_domain *irq_domain;
+
+ int irq;
+ int irq_gpio;
+ bool wakeup;
+ struct mutex irqlock;
+ int irq_masks_cur[MAX77802_IRQ_GROUP_NR];
+ int irq_masks_cache[MAX77802_IRQ_GROUP_NR];
+};
+
+enum max77802_types {
+ TYPE_MAX77802,
+};
+
+extern int max77802_irq_init(struct max77802_dev *max77802);
+extern void max77802_irq_exit(struct max77802_dev *max77802);
+extern int max77802_irq_resume(struct max77802_dev *max77802);
+
+#endif /* __LINUX_MFD_MAX77802_PRIV_H */
new file mode 100644
@@ -0,0 +1,124 @@
+/*
+ * max77802.h - Driver for the Maxim 77802
+ *
+ * Copyright (c) 2013-2014 Google, Inc
+ *
+ * Copyright (C) 2012 Samsung Electrnoics
+ * Chiwoong Byun <woong.byun@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * This driver is based on max8997.h
+ *
+ * MAX77802 has PMIC, RTC devices.
+ * The devices share the same I2C bus and included in
+ * this mfd driver.
+ */
+
+#ifndef __LINUX_MFD_MAX77802_H
+#define __LINUX_MFD_MAX77802_H
+
+#include <linux/regulator/consumer.h>
+
+/* MAX77802 regulator IDs - LDOS must come before BUCKs */
+enum max77802_regulators {
+ MAX77802_LDO1 = 0,
+ MAX77802_LDO2,
+ MAX77802_LDO3,
+ MAX77802_LDO4,
+ MAX77802_LDO5,
+ MAX77802_LDO6,
+ MAX77802_LDO7,
+ MAX77802_LDO8,
+ MAX77802_LDO9,
+ MAX77802_LDO10,
+ MAX77802_LDO11,
+ MAX77802_LDO12,
+ MAX77802_LDO13,
+ MAX77802_LDO14,
+ MAX77802_LDO15,
+ MAX77802_LDO16,
+ MAX77802_LDO17,
+ MAX77802_LDO18,
+ MAX77802_LDO19,
+ MAX77802_LDO20,
+ MAX77802_LDO21,
+ MAX77802_LDO22,
+ MAX77802_LDO23,
+ MAX77802_LDO24,
+ MAX77802_LDO25,
+ MAX77802_LDO26,
+ MAX77802_LDO27,
+ MAX77802_LDO28,
+ MAX77802_LDO29,
+ MAX77802_LDO30,
+ MAX77802_LDO31,
+ MAX77802_LDO32,
+ MAX77802_LDO33,
+ MAX77802_LDO34,
+ MAX77802_LDO35,
+ MAX77802_BUCK1,
+ MAX77802_BUCK2,
+ MAX77802_BUCK3,
+ MAX77802_BUCK4,
+ MAX77802_BUCK5,
+ MAX77802_BUCK6,
+ MAX77802_BUCK7,
+ MAX77802_BUCK8,
+ MAX77802_BUCK9,
+ MAX77802_BUCK10,
+
+ MAX77802_REG_MAX,
+};
+
+struct max77802_regulator_data {
+ int id;
+ int opmode;
+ struct regulator_init_data *initdata;
+ struct device_node *of_node;
+};
+
+enum max77802_opmode {
+ MAX77802_OPMODE_OFF,
+ MAX77802_OPMODE_STANDBY,
+ MAX77802_OPMODE_LP,
+ MAX77802_OPMODE_NORMAL,
+};
+
+struct max77802_opmode_data {
+ int id;
+ int mode;
+};
+
+struct max77802_platform_data {
+ /* IRQ */
+ int irq_gpio;
+ int ono;
+ int wakeup;
+
+ /* ---- PMIC ---- */
+ struct max77802_regulator_data *regulators;
+ int num_regulators;
+
+ struct max77802_opmode_data *opmode_data;
+
+ /*
+ * GPIO-DVS feature is not fully enabled with the current version of
+ * MAX77802 driver, but the driver does support using a DVS index other
+ * than the default of 0.
+ */
+ int buck_gpio_dvs[3]; /* GPIO of [0]DVS1, [1]DVS2, [2]DVS3 */
+ int buck_default_idx; /* Default value of DVS1, 2, 3 */
+
+ int buck_gpio_selb[5]; /* 77802: 1, 2, 3, 4, 6 */
+};
+
+#endif /* __LINUX_MFD_MAX77802_H */
Maxim MAX77802 is a power management chip that contains 10 high efficiency Buck regulators, 32 Low-dropout (LDO) regulators used to power up application processors and peripherals, a 2-channel 32kHz clock outputs, a Real-Time-Clock (RTC) and a I2C interface to program the individual regulators, clocks outputs and the RTC. This patch adds the core support for MAX77802 PMIC and is based on a driver added by Simon Glass to the Chrome OS kernel 3.8 tree. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> --- Documentation/devicetree/bindings/mfd/max77802.txt | 88 ++++++ drivers/mfd/Kconfig | 13 + drivers/mfd/Makefile | 1 + drivers/mfd/max77802-irq.c | 332 +++++++++++++++++++++ drivers/mfd/max77802.c | 282 +++++++++++++++++ include/linux/mfd/max77802-private.h | 291 ++++++++++++++++++ include/linux/mfd/max77802.h | 124 ++++++++ 7 files changed, 1131 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/max77802.txt create mode 100644 drivers/mfd/max77802-irq.c create mode 100644 drivers/mfd/max77802.c create mode 100644 include/linux/mfd/max77802-private.h create mode 100644 include/linux/mfd/max77802.h