| Message ID | 1405047349-15101-6-git-send-email-d-gerlach@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Thursday 10 July 2014 10:55 PM, Dave Gerlach wrote: > Add the device tree bindings document for am3353 wkup_m3. > > Signed-off-by: Dave Gerlach <d-gerlach@ti.com> > CC: Ohad Ben-Cohen <ohad@wizery.com> > CC: Benoit Cousson <bcousson@baylibre.com> > --- Looks like you missed to copy device tree list and maintainers. As Tony suggested, split up the series and send the wkup_m3 related patches separately along with bindings and mark the DT folks on email. > .../bindings/remoteproc/wkup_m3_rproc.txt | 46 ++++++++++++++++++++++ > 1 file changed, 46 insertions(+) > create mode 100644 Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt > > diff --git a/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt > new file mode 100644 > index 0000000..e9dd909 > --- /dev/null > +++ b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt > @@ -0,0 +1,46 @@ > +Wakeup M3 Remote Proc Driver > +===================== > + > +TI AMx3 Family devices use a Cortex M3 co-processor to help with various > +low power tasks that cannot be controlled from the MPU. The CM3 requires > +a firmware binary to accomplish this and communicates with the MPU through > +IPC registers present in the SoCs control module. The wkup_m3 remoteproc > +driver handles the loading of the firmware and exposes an API to > +communicate with the wkup_m3 through the use of the IPC registers and a > +mailbox. > + > +Wkup M3 Device Node: > +==================== > +A wkup_m3 device node is used to represent a wakeup M3 IP instance within > +a SoC. The sub-mailboxes are represented as child node of this parent node. > + > +Required properties: > +-------------------- > +- compatible: Should be "ti,am3353-wkup-m3" for AM33xx SoCs > +- reg: Contains the wkup_m3 register address ranges for > + umem, dmem, and ipc-regs. > +- reg-names: Names for reg addresses given above > +- interrupts: Contains the interrupt information for the wkup_m3 > + interrupt that signals the MPU. > +- ti,hwmods: Name of the hwmod associated with the mailbox > +- ti,no-reset-on-init: Reset is handled after fw has been loaded, not at > + init of hwmod. > +- mbox-names: Name of the mbox channel for the IPC framework > +- mbox: Phandle used by IPC framework to get correct mbox > + channel for communication. > + > +Example: > +-------- > +/* AM33xx */ > +wkup_m3: wkup_m3@44d00000 { > + compatible = "ti,am3353-wkup-m3"; > + reg = <0x44d00000 0x4000 > + 0x44d80000 0x2000 > + 0x44e11324 0x0024>; > + reg-names = "m3_umem", "m3_dmem", "ipc_regs"; > + interrupts = <78>; > + ti,hwmods = "wkup_m3"; > + ti,no-reset-on-init; > + mbox-names = "wkup_m3"; > + mbox = <&mailbox &mbox_wkupm3>; > +}; > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Dave, On 07/14/2014 09:41 AM, Santosh Shilimkar wrote: > On Thursday 10 July 2014 10:55 PM, Dave Gerlach wrote: >> Add the device tree bindings document for am3353 wkup_m3. >> >> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> >> CC: Ohad Ben-Cohen <ohad@wizery.com> >> CC: Benoit Cousson <bcousson@baylibre.com> >> --- > Looks like you missed to copy device tree list and maintainers. > As Tony suggested, split up the series and send the wkup_m3 related > patches separately along with bindings and mark the DT folks on email. > >> .../bindings/remoteproc/wkup_m3_rproc.txt | 46 ++++++++++++++++++++++ >> 1 file changed, 46 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt >> >> diff --git a/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt >> new file mode 100644 >> index 0000000..e9dd909 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt >> @@ -0,0 +1,46 @@ >> +Wakeup M3 Remote Proc Driver >> +===================== >> + >> +TI AMx3 Family devices use a Cortex M3 co-processor to help with various >> +low power tasks that cannot be controlled from the MPU. The CM3 requires >> +a firmware binary to accomplish this and communicates with the MPU through >> +IPC registers present in the SoCs control module. The wkup_m3 remoteproc >> +driver handles the loading of the firmware and exposes an API to >> +communicate with the wkup_m3 through the use of the IPC registers and a >> +mailbox. >> + >> +Wkup M3 Device Node: >> +==================== >> +A wkup_m3 device node is used to represent a wakeup M3 IP instance within >> +a SoC. The sub-mailboxes are represented as child node of this parent node. >> + >> +Required properties: >> +-------------------- >> +- compatible: Should be "ti,am3353-wkup-m3" for AM33xx SoCs >> +- reg: Contains the wkup_m3 register address ranges for >> + umem, dmem, and ipc-regs. >> +- reg-names: Names for reg addresses given above You should explicitly state the names here. Giving any different names will cause the driver to fail. >> +- interrupts: Contains the interrupt information for the wkup_m3 >> + interrupt that signals the MPU. >> +- ti,hwmods: Name of the hwmod associated with the mailbox hwmod is not associated with mailbox here, please fix the cut-copy-paste error. regards Suman >> +- ti,no-reset-on-init: Reset is handled after fw has been loaded, not at >> + init of hwmod. >> +- mbox-names: Name of the mbox channel for the IPC framework >> +- mbox: Phandle used by IPC framework to get correct mbox >> + channel for communication. >> + >> +Example: >> +-------- >> +/* AM33xx */ >> +wkup_m3: wkup_m3@44d00000 { >> + compatible = "ti,am3353-wkup-m3"; >> + reg = <0x44d00000 0x4000 >> + 0x44d80000 0x2000 >> + 0x44e11324 0x0024>; >> + reg-names = "m3_umem", "m3_dmem", "ipc_regs"; >> + interrupts = <78>; >> + ti,hwmods = "wkup_m3"; >> + ti,no-reset-on-init; >> + mbox-names = "wkup_m3"; >> + mbox = <&mailbox &mbox_wkupm3>; >> +}; >> > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Santosh, Suman, On 07/14/2014 11:33 AM, Suman Anna wrote: > Hi Dave, > > On 07/14/2014 09:41 AM, Santosh Shilimkar wrote: >> On Thursday 10 July 2014 10:55 PM, Dave Gerlach wrote: >>> Add the device tree bindings document for am3353 wkup_m3. >>> >>> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> >>> CC: Ohad Ben-Cohen <ohad@wizery.com> >>> CC: Benoit Cousson <bcousson@baylibre.com> >>> --- >> Looks like you missed to copy device tree list and maintainers. >> As Tony suggested, split up the series and send the wkup_m3 related >> patches separately along with bindings and mark the DT folks on email. Yes I did, I will fix this when I resend the split up series. Thanks. >> >>> .../bindings/remoteproc/wkup_m3_rproc.txt | 46 ++++++++++++++++++++++ >>> 1 file changed, 46 insertions(+) >>> create mode 100644 Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt >>> >>> diff --git a/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt >>> new file mode 100644 >>> index 0000000..e9dd909 >>> --- /dev/null >>> +++ b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt >>> @@ -0,0 +1,46 @@ >>> +Wakeup M3 Remote Proc Driver >>> +===================== >>> + >>> +TI AMx3 Family devices use a Cortex M3 co-processor to help with various >>> +low power tasks that cannot be controlled from the MPU. The CM3 requires >>> +a firmware binary to accomplish this and communicates with the MPU through >>> +IPC registers present in the SoCs control module. The wkup_m3 remoteproc >>> +driver handles the loading of the firmware and exposes an API to >>> +communicate with the wkup_m3 through the use of the IPC registers and a >>> +mailbox. >>> + >>> +Wkup M3 Device Node: >>> +==================== >>> +A wkup_m3 device node is used to represent a wakeup M3 IP instance within >>> +a SoC. The sub-mailboxes are represented as child node of this parent node. >>> + >>> +Required properties: >>> +-------------------- >>> +- compatible: Should be "ti,am3353-wkup-m3" for AM33xx SoCs >>> +- reg: Contains the wkup_m3 register address ranges for >>> + umem, dmem, and ipc-regs. >>> +- reg-names: Names for reg addresses given above > > You should explicitly state the names here. Giving any different names > will cause the driver to fail. Alright I will move the names from the item above and add some details. > >>> +- interrupts: Contains the interrupt information for the wkup_m3 >>> + interrupt that signals the MPU. >>> +- ti,hwmods: Name of the hwmod associated with the mailbox > > hwmod is not associated with mailbox here, please fix the cut-copy-paste > error. Yep that's my bad, sorry about that. Regards, Dave > > regards > Suman > > >>> +- ti,no-reset-on-init: Reset is handled after fw has been loaded, not at >>> + init of hwmod. >>> +- mbox-names: Name of the mbox channel for the IPC framework >>> +- mbox: Phandle used by IPC framework to get correct mbox >>> + channel for communication. >>> + >>> +Example: >>> +-------- >>> +/* AM33xx */ >>> +wkup_m3: wkup_m3@44d00000 { >>> + compatible = "ti,am3353-wkup-m3"; >>> + reg = <0x44d00000 0x4000 >>> + 0x44d80000 0x2000 >>> + 0x44e11324 0x0024>; >>> + reg-names = "m3_umem", "m3_dmem", "ipc_regs"; >>> + interrupts = <78>; >>> + ti,hwmods = "wkup_m3"; >>> + ti,no-reset-on-init; >>> + mbox-names = "wkup_m3"; >>> + mbox = <&mailbox &mbox_wkupm3>; >>> +}; >>> >> > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt new file mode 100644 index 0000000..e9dd909 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt @@ -0,0 +1,46 @@ +Wakeup M3 Remote Proc Driver +===================== + +TI AMx3 Family devices use a Cortex M3 co-processor to help with various +low power tasks that cannot be controlled from the MPU. The CM3 requires +a firmware binary to accomplish this and communicates with the MPU through +IPC registers present in the SoCs control module. The wkup_m3 remoteproc +driver handles the loading of the firmware and exposes an API to +communicate with the wkup_m3 through the use of the IPC registers and a +mailbox. + +Wkup M3 Device Node: +==================== +A wkup_m3 device node is used to represent a wakeup M3 IP instance within +a SoC. The sub-mailboxes are represented as child node of this parent node. + +Required properties: +-------------------- +- compatible: Should be "ti,am3353-wkup-m3" for AM33xx SoCs +- reg: Contains the wkup_m3 register address ranges for + umem, dmem, and ipc-regs. +- reg-names: Names for reg addresses given above +- interrupts: Contains the interrupt information for the wkup_m3 + interrupt that signals the MPU. +- ti,hwmods: Name of the hwmod associated with the mailbox +- ti,no-reset-on-init: Reset is handled after fw has been loaded, not at + init of hwmod. +- mbox-names: Name of the mbox channel for the IPC framework +- mbox: Phandle used by IPC framework to get correct mbox + channel for communication. + +Example: +-------- +/* AM33xx */ +wkup_m3: wkup_m3@44d00000 { + compatible = "ti,am3353-wkup-m3"; + reg = <0x44d00000 0x4000 + 0x44d80000 0x2000 + 0x44e11324 0x0024>; + reg-names = "m3_umem", "m3_dmem", "ipc_regs"; + interrupts = <78>; + ti,hwmods = "wkup_m3"; + ti,no-reset-on-init; + mbox-names = "wkup_m3"; + mbox = <&mailbox &mbox_wkupm3>; +};
Add the device tree bindings document for am3353 wkup_m3. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> CC: Ohad Ben-Cohen <ohad@wizery.com> CC: Benoit Cousson <bcousson@baylibre.com> --- .../bindings/remoteproc/wkup_m3_rproc.txt | 46 ++++++++++++++++++++++ 1 file changed, 46 insertions(+) create mode 100644 Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt